| Age | Commit message (Collapse) | Author |
|---|
|
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver can clearly enable fast-xmit since it does rate
control in the device and thus must do duration calculation
there as well.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With latest additions to the driver it seems
viable to enable support for IBSS-RSN.
It seems to work on QCA988X and 999.999.0.636 but
is a bit slow to exchange RSN keys for some
reason. This may be a firmware quirk or ath10k is
missing something. Nevertheless it makes sense to
finally enable IBSS-RSN in ath10k even if somewhat
handicapped.
QCA6174 firmware doesn't seem to be able to Tx
EAPOL frames at all now (they get stuck in hw
queues for some reason) so it never gets to set
the keys in driver. It's fairly safe to assume that
once this is fixed IBSS-RSN will work with QCA6174
firmware without any additional changes. Hence no
special handling for advertising
IEEE80211_HW_SUPPORTS_PER_STA_GTK and
WIPHY_FLAG_IBSS_RSN is done now.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Some time ago there was a weird issue with AP
using wrong multicast keys and generating
corrupted traffic on 10.1 firmware.
Apparently a very similar problem applies for
IBSS-RSN on 999.999.0.636.
ath10k doesn't have IBSS-RSN enabled yet. This
patch is a prerequisite to support it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Apparently firmware requires both pairwise and
groupwise keys to be installed per-peer for static
WEP in IBSS. This wasn't necessary for AP mode
(and installing both doesn't seem to break AP
mode thus there's no special handling).
Also there seems to be some kind of issue with
mapping tx/rx keys in firmware properly which
resulted in wrong keys being used and broken
communication between devices.
It can be argued the vdev param part is more of a
workaround than a real fix. However I couldn't
figure out how to fix this differently. It works
and isn't super ugly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Firmware actually re-creates peer entry when
reassoc flag is set. This is undesired and could
cause trouble with IBSS crypto-wise. This is also
important for upcomming bitrate mask improvement.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
mac80211 sets static WEP keys as groupwise while
firmware requires them to be installed twice as
both pairwise and groupwise.
Until now these keys were installed once as
pairwise only and, due to that special handling,
needed additional tricks to support 802.1x as
well.
Without this patch in some cases (when AP and
ath10k client use different default tx keys)
multicast communication was broken.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
|
|
This improves chances of getting onto a foreign
channel and thus makes P2P a bit more reliable.
Without scan burst it was possible for firmware to
not switch to foreign channel resulting in "failed
to switch to channel for roc scan" warning. This
would also effectively fail some offchan tx
requests and lead to P2P find/connect taking
longer. This could be observed when other vifs
were running/busy, e.g. with P2P GO.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It is not guaranteed firmware will switch to
foreign channel immediately after starting scan
sequence. To account for that don't use duration
parameter for scan time. Instead request insanely
long scan and use timeout worker to cancel it from
driver.
This should improve P2P reliability a bit.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
|
|
The default keyidx callback may be called after
more than 1 key is installed. This led to only 1
WEP key being reinstalled only. This caused Rxed
traffic encrypted with other WEP keys to be
dropped in client mode.
Tested-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The variable should be cleared regardless of
whether there's a peer associated with the key or
not.
This fixes case when user first associates with 2
WEP keys and then disconnects and connects with 1
WEP key. This resulted in WEP key count being 2 in
the driver leading to default keyidx fixup
failure.
Tested-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Firmwares that indicate BURST_SERVICE as enabled
could overwrite some wmm parameters (eg. txop).
This could lead IOT and balancing issues.
Hence disable this by default.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
WLAN.RM.2.0-00073 firmware requires self-peer to
be created prior to issuing scan command. Without
this wmi-tlv with qca6174 firmware crashes after
submitting a scan request.
Creating the peer as soon as add_interface()
shouldn't be a problem.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The code was a bit convoluted. Clean it up and
prepare for future changes.
While at it this fixes incorrect verification of
'single nss' case when ss2 rates were missing
while ss1 and ss3 were requested resulting in
nss=3 being set:
iw wlan1 set bitrates legacy-5 ht-mcs-5 0 1 2 3 4 5 6 7 16 17 18 19 20 21 22 23 vht-mcs-5 1:0-9 3:0-9
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This effectively enables multi-channel operation
on qca6174 WLAN.RM.2.0-00073 (and possibly any
newer firmware release for qca6174).
This adds appopriate interface combinations and
initializes firmware channel scheduler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
qca6174 wmi-tlv firmware defines a new wmi event
for host tx pausing (i.e. stop/wake tx queues).
Map these events to ath10k/mac80211 tx queue
control.
This is important for multi-channel throughput
performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Tx queue locking was very simple until now.
Multi-channel support will require a more flexible
and fine grained control.
This introduces a per-hw and per-vif (each with a
bitmask of reasons) tx queue locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The chanctx API will allow ath10k to support
multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Number of channels is stored in a separate macro
in a header file and channel list is constructed
independently. The macro is used to define survey
array.
This fixes a recent regression introduced after
adding support for 144 channel. The regression
would lead to a warning and incomplete survey data
on channel 165:
chan info: invalid frequency 5825 (idx 38 out of bounds)
Also make sure to enforce the sizes and avoid this
kind of problem in the future.
Fixes: 4a7898fed5f3 ("ath10k: enable channel 144 on 5GHz band")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, respectively 'ret'
renamed, and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While debugging something else I noticed AID was
set to 0. This could lead to powersave issues in
station mode. Maybe this isn't really necessary
but set it properly just to be sure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Don't use literal values for offsets. While at it
rename a function so it is more clear what it
checks for.
This finally takes care of the last magic
5GHz/OFDM offset.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It's possible to derive rate index from bitrate
without any additional mapping structures/logic.
This should have little to none impact on
performance since this is only done for management
frames and the previous approach wasn't
particularly optimized.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Instead of using a hacky table and magic values
use supported band information advertised to
mac80211.
This may impact performance a little when dealing
with legacy rx rates depending on system
architecture. It's probably negligible.
This also fixes a highly theoretical corner case
when HT/VHT rates weren't reported correctly if
channel frequency wasn't known.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Use the existing ieee80211_rate array instead of
definining separate one. This gets rid of the ugly
4-index offset when dealing with 5GHz band.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Using raw values is discouraged. Having
defines/enums is preferred.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It was superfluous and confusing. It's better to
define the structure explicitly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
There's no need to store rate values in hw_value.
This frees up the hw_value for better future use.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Prepare the code for future changes so that new
code can refer to rate-related stuff without
forward declarations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch introduces tdls without tdls peer uapsd and tdls channel switching.
Transmitting tdls data frames works only for ethernet type frames, that's why
data addressed to tdls sta is in ethernet format.
This patch depends on commit c23e31cf7b55 ("mac80211: initialize rate control
earlier for tdls station").
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently station counting functions
(inc_num_stations/dec_num_stations) does not handle
tdls type of stations. Tdls station should be counted
because it consumes peer in firmware. Only not tdls
stations are excluded from this counting.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
There are a few different tx paths depending on
firmware and frame itself.
Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
If htt.freq isn't cleared and contains garbage fw
may discard tx packets. Prevent this from
happening by clearing htt.freq properly.
Possible manifestation of the problem could be not
being able to send auth request/response frames on
firmware with HTT >= 3.4 (when freq param was
introduced), e.g. on qca6174.
Fixes: 8d6d36243610 ("ath10k: fix offchan reliability")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Patch "ath10k: introduce basic tdls functionality" depends on this mac80211
patch:
c23e31cf7b55 mac80211: initialize rate control earlier for tdls station
|
|
Add support for WOW disconnect and magic-packet.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs
echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ANI helps to improve connectvity and performance in a noisy environment.
Enabling this feature would help the user experience a better and stable
wireless connection in a noisy environmnet. This feature is currently not
enabled for ath10k. Enable this feature by default.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Enable channel 144 on 5GHz band since 802.11ac introduced it.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Thermal throttling is not handled in software restart and device
bootup. Also it needs to be configured whenever quiet period got
updated. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
By default rts protection is enabled in firmware for the second
rateset. Currently ath10k selects RTS profile (only for software
retries), when legacy stations are associated or asked by mac80211.
On congested environment, when AP is running in HT/VHT mode and
there are no legacy clients associated, this will impact the
robustness. Also enabling RTS protection only for second rateset will
not impact performance on clear environment. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Setup maximum number of associated stations supported in
AP/P2P_GO mode.
This allow hostapd/wpa_supplicant to play with that limit
and set more information (eg. P2P group limit bit for P2P_GO).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
NativeWifi tx mode expects QoS Data frames to be
delivered as Data frames with QoS part (e.g. tid)
being delievered out-of-band in fw tx command.
The QoS bit wasn't stripped before submitting to
firmware.
Stripping fixes two known problems:
* qca6174 IOT with some APs, e.g.
Cisco AIR-AP 1252 (which would crash after
ath10k association). Some ath9k APs would
crash as well.
* sniffing own tx frames via radiotap because,
e.g. wireshark was seeing QoS bit set but
since QoS Control was stripped in ath10k it
would parse beginning of LLC/SNAP
>From debugability point of view this removes the
ability to distinguish QoS from non-QoS frames
when sniffing own tx via radiotap. On the other
hand frames can be now parsed correctly without
special software modification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
While testing with older supplicant, .drv_set_key() was failing due to
higher than ath10k firmware could handle key_index (WMI_MAX_KEY_INDEX == 3).
--
wpa_driver_nl80211_set_key: ifindex=15 alg=4 addr=0x7f02b129fbe3 key_idx=4 set_tx=0 seq_len=6 key_len=16
broadcast key
nl80211: set_key failed; err=-22 Invalid argument)
wlan0: WPA: Failed to configure IGTK to the driver
wlan0: RSN: Failed to configure IGTK
--
In order to fix this case (PMF: AES-CMAC/IGTK) force the AES_CMAC cipher to
be handled by software.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Some firmware revisions (e.g. qca6174 with fw73)
don't deliver beacons to host reliably. This
causes random disconnects even in perfect
conditions. This is most visible with
multi-channel operation.
All available firmware revisions seem to support
beacon miss offloading so there shouldn't be any
problems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Commit 370e567363e6 ("ath10k: fix broken traffic for 802.1x in client mode")
introduced a regression on WPA crypto. All keys were treated as if they were
WEP which resulted in WPA being incorrectly installed to fw/hw and subsequently
no traffic.
Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Commit 548462133d98 ("ath10k: fix interrupt storm") introduced a
regression. The condition responsible for bringing up monitor vdev was broken
and it was never started for CAC so effectivelly CAC would not detect radar
pulses.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
