summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/wcn36xx/main.c
AgeCommit message (Collapse)Author
2020-11-07wcn36xx: Enable firmware offloaded keepaliveBryan O'Donoghue
This patch calls wcn36xx_smd_keep_alive_req() on the STA patch immediately after associating with an AP. This will cause the firmware to send a NULL packet out to the AP every 30 seconds, thus offloading keep-alive processing from the SoC to the firmware. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201103121735.291324-4-bryan.odonoghue@linaro.org
2020-11-07wcn36xx: Enable firmware link monitoringBryan O'Donoghue
This patch switches on CONNECTION_MONITOR. Once done it is up to the firmware to send keep alive and to monitor the link state. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201103121735.291324-3-bryan.odonoghue@linaro.org
2020-09-22wcn36xx: Ensure spaces between functionsBryan O'Donoghue
This is a small update to fix an error I saw where a few functions do not have a blank line in between them. Affects smd.c and main.c - no logic is affected by this change. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200910150845.2179320-3-bryan.odonoghue@linaro.org
2020-09-22wcn36xx: Advertise ieee802.11 VHT flagsBryan O'Donoghue
This patch adds ieee802.11 VHT flags for the wcn3680b. - RX_STBC1 - SU Beamformee - MU Beamformee - VHT80 SGI - Single spatial stream RX LDPC is declared as supported in the datasheet but not enabled at this time. After this patch is applied an AP should see the wcn3680 as an 802.11ac capable device. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200910150822.2179261-5-bryan.odonoghue@linaro.org
2020-09-22wcn36xx: Add VHT rates to wcn36xx_update_allowed_rates()Bryan O'Donoghue
This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine. Thus allowing the driver to latch the declared rates and transmit them to the firmware in the same way as other 80211.n rates are. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200910150822.2179261-4-bryan.odonoghue@linaro.org
2020-09-22wcn36xx: Encode PHY mode for 80MHz channel in hw_valueBryan O'Donoghue
This commit encodes the 802.11ac PHY mode for a given channel in the upper bits of the hw_value field. This allows for a neat read-out and application of the relevant PHY setting. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200910150708.2179043-5-bryan.odonoghue@linaro.org
2020-09-21wcn36xx: Add wcn36xx_set_default_rates_v1Bryan O'Donoghue
Add a routine to set some additional default parameters associated with the V1 data structure. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200910150552.2178882-2-bryan.odonoghue@linaro.org
2020-09-02wcn36xx: Hook and identify RF_IRIS_WCN3680Bryan O'Donoghue
If DT indicates we are dealing with a WCN3680 mark the rf_id field as RF_IRIS_WCN3680 allowing for further chip-specific logic. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200829033846.2167619-3-bryan.odonoghue@linaro.org
2020-08-27wcn36xx: Disable bmps when encryption is disabledLoic Poulain
For whatever reason, when connected to an open/no-security BSS, the wcn36xx controller in bmps mode does not forward 'wake-up' beacons despite AP sends DTIM with station AID. Meaning that AP is not able to wakeup the station and needs to wait for the station to wakeup by its own (TX data, keep alive pkt...), causing serious latency issues and unexpected deauth. When connected to AP with encryption enabled, this issue does not occur. So a simple workaround is to only enable bmps support in that case. Ideally, it should be propertly fixed to allow bmps support with open BSS, whatever the issue is at driver or firmware level. Tested on wcn3620 and wcn3680. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1598363127-26066-1-git-send-email-loic.poulain@linaro.org
2020-08-27wcn36xx: Fix software-driven scanLoic Poulain
For software-driven scan, rely on mac80211 software scan instead of internal driver implementation. The internal implementation cause connection trouble since it keep the antenna busy during the entire scan duration, moreover it's only a passive scanning (no probe request). Therefore, let mac80211 manages sw scan. Note: we fallback to software scan if firmware does not report scan offload support or if we need to scan the 5Ghz band (currently not supported by the offload scan...). Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1598288035-19790-1-git-send-email-loic.poulain@linaro.org
2020-08-17wcn36xx: Fix reported 802.11n rx_highest rate wcn3660/wcn3680Bryan O'Donoghue
Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here. This patch fixes the data-rate declared in the 5GHz table. Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
2020-08-14wcn36xx: Add TX ack supportLoic Poulain
The controller is capable of reporting TX indication which can be used to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set. The support was only partially implemented. The firmware can be configured for reporting event when a packet is acked, without specifying which packet though. In order to send a packet flagged with TX status callback, we need to stop the queue, submit the packet and wait for the firmware ack event. Then the queue can be restarted and mac80211 status callback called. In case the packet is not acked, no ack event will be received, therefore a timeout mechanism is introduced to restart the queue and call the status cb in case no event is received after a 100ms. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
2020-08-14wcn36xx: Fix multiple AMPDU sessions supportLoic Poulain
Several AMPDU sessions can be started, e.g. for different TIDs. Currently the driver does not take care of the session ID when requesting block-ack (statically set to 0), which leads to never block-acked packet with sessions other than 0. Fix this by saving the session id when creating the ba session and use it in subsequent ba operations. This issue can be reproduced with iperf in two steps (tid 0 strem then tid 6 stream). 1.0 iperf -s # wcn36xx side 1.1 iperf -c ${IP_ADDR} # host side Then 2.0 iperf -s -u -S 0xC0 # wcn36xx side 2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
2020-05-11wcn36xx: Fix error handling path in 'wcn36xx_probe()'Christophe JAILLET
In case of error, 'qcom_wcnss_open_channel()' must be undone by a call to 'rpmsg_destroy_ept()', as already done in the remove function. Fixes: 5052de8deff5 ("soc: qcom: smd: Transition client drivers from smd to rpmsg") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200507043619.200051-1-christophe.jaillet@wanadoo.fr
2019-12-18wcn36xx: disable HW_CONNECTION_MONITOREduardo Abinader
Whenever the signal stregth decays smoothly and physical connnection is already gone and no deauth has arrived, the qcom soc is not able to indicate neither WCN36XX_HAL_MISSED_BEACON_IND nor WCN36XX_HAL_MISSED_BEACON_IND. It was noticed that such situation gets even more reproducible, when the driver fails to enter bmps mode - which is highly likely to occur. Thus, in order to provide proper disconnection of the connected STA, let mac80211 handle it, instead of wcn3xx driver. Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-11-06Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo
ath.git patches for 5.5. Major changes: wil6210 * add SPDX license identifiers
2019-10-31wcn36xx: remove unecessary returnEduardo Abinader
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-10-04mac80211: simplify TX aggregation startJohannes Berg
There really is no need to make drivers call the ieee80211_start_tx_ba_cb_irqsafe() function and then schedule the worker if all we want is to set a bit. Add a new return value (that was previously considered invalid) to indicate that the driver is immediately ready for the session, and make drivers use it. The only drivers that remain different are the Intel ones as they need to negotiate more with the firmware. Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-07-02wcn36xx: drop unnecessary initialization of variablesDaniel Mack
Initialization is unneccessary when the variable is written before it is read. There were some occasions in which the driver would initialize `ret' during declaration without need. Purely a cosmetic change with no functional impact. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-29wcn36xx: Fix WEP encryptionLoic Poulain
In case of WEP encryption, driver has to configure shared key for associated station(s). Note that sta pointer is NULL in case of non pairwise key, causing NULL pointer dereference with existing code (sta_priv->is_data_encrypted). Fix this by using associated sta list instead. This enables WEP support as client, WEP AP is non-functional. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-29wcn36xx: Track associated stationsLoic Poulain
Add list of associated stations(STA, AP, peer...) per vif. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-29wcn36xx: Fix WEP104 encryption typeLoic Poulain
This is an obvious copy & paste bug. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: Add support for Factory Test Mode (FTM)Eyal Ilsar
Introduce infrastructure for supporting Factory Test Mode (FTM) of the wireless LAN subsystem. In order for the user space to access the firmware in test mode the relevant netlink channel needs to be exposed from the kernel driver. The above is achieved as follows: 1) Register wcn36xx driver to testmode callback from netlink 2) Add testmode callback implementation to handle incoming FTM commands 3) Add FTM command packet structure 4) Add handling for GET_BUILD_RELEASE_NUMBER (msgid=0x32A2) 5) Add generic handling for all PTT_MSG packets Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org> Signed-off-by: Ramon Fried <ramon.fried@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: set PREASSOC and IDLE stated when BSS info changesDaniel Mack
When a BSSID is joined, set the link status to 'preassoc', and set it to 'idle' when the BSS is deleted. This is what the downstream driver is doing, and it seems to improve the reliability during connect/disconnect stress tests. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: set DMA mask explicitlyDaniel Mack
The device takes 32-bit addresses only, so inform the DMA API about it. This is the default on msm8016, so that doesn't change anything, but it's best practice to be explicit. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24wcn36xx: handle scan cancellation when firmware support is missingDaniel Mack
For firmwares that don't have the SCAN_OFFLOAD feature bit set, do not call into wcn36xx_smd_stop_hw_scan(). Instead, stop the asynchronous work and call into ieee80211_scan_completed() immediately. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24wcn36xx: cancel pending scan request when interface goes downDaniel Mack
When the network interface goes down while a scan request is still pending that can't be stopped due to firmware hickups, wcn->scan_req remains set, even though the hardware is deinitialized. This results in -EBUSY for all scan requests after the interface was brought up again. Fix this by explicitly completing pending scan requests in wcn36xx_stop(). Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24wcn36xx: pass correct BSS index when deleting BSS keysDaniel Mack
The firmware message to delete BSS keys expects a BSS index to be passed. This field is currently hard-coded to 0. Fix this by passing in the index we received from the firmware when the BSS was configured. The encryption type in that message also needs to be set to what was used when the key was set, so the assignment of vif_priv->encrypt_type is now done after the firmware command was sent. This reportedly fixes the following error in AP mode: wcn36xx: ERROR hal_remove_bsskey response failed err=6 Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the keys associated with it. Trying to remove the key explicitly afterwards will hence lead to the following message: wcn36xx: ERROR hal_remove_bsskey response failed err=16 This is now suppressed with an extra check for the BSS index validity. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-10wcn36xx: don't delete invalid bss indicesDaniel Mack
The firmware code cannot cope with requests to remove BSS indices that have not previously been added. This primarily happens when the device is suspended and then resumed. ieee80211_reconfig() then calls into wcn36xx_bss_info_changed() with an empty bssid and BSS_CHANGED_BSSID set, which subsequently leads to a firmware crash: [ 43.647928] qcom-wcnss-pil a204000.wcnss: fatal error received: halMsg.c:4964:halMsg_DelBss: Invalid BSSIndex 0 [ 43.647959] remoteproc remoteproc0: crash detected in a204000.wcnss: type fatal error To fix this, set bss_index to WCN36XX_HAL_BSS_INVALID_IDX for all bss that have not been configured in the firmware, and don't call into the firmware with invalid indices. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-29wcn36xx: turn off probe response offloadingRamon Fried
It appears that the WCN36xx firmware doesn't actually respond to probe requests. Until it's resolved, switch the probe response responsibility to the 802.11 layer to allow creation of hidden SSID AP's. Signed-off-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-26wcn36xx: reduce verbosity of drivers messagesRamon Fried
Whenever the WLAN interface is started the FW version and caps are printed. The caps now will be displayed only in debug mode. Firmware version will be displayed only once on first startup of the interface. Change-Id: I4db6ea7f384fe15eebe4c3ddb1d1ccab00094332 Signed-off-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-02-27wcn36xx: Fix warning due to duplicate scan_completed notificationLoic Poulain
The wcn36xx_cancel_hw_scan method stops the hw scan and notify the scan completion via ieee80211_scan_completed. However, on scan offload cancellation, firmware sends a scan complete indication, triggering a new call to ieee80211_scan_completed. This leads to kernel warn since the scan has already been completed. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
BPF alignment tests got a conflict because the registers are output as Rn_w instead of just Rn in net-next, and in net a fixup for a testcase prohibits logical operations on pointers before using them. Also, we should attempt to patch BPF call args if JIT always on is enabled. Instead, if we fail to JIT the subprogs we should pass an error back up and fail immediately. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-04wcn36xx: Fix dynamic power savingLoic Poulain
Since driver does not report hardware dynamic power saving cap, this is up to the mac80211 to manage power saving timeout and state machine, using the ieee80211 config callback to report PS changes. This patch enables/disables PS mode according to the new configuration. Remove old behaviour enabling PS mode in a static way, this make the device unusable when power save is enabled since device is forced to PS regardless RX/TX traffic. Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-12-14wcn36xx: Add hardware scan offload supportLoic Poulain
Current hw_scan implementation does not trigger offloaded hardware scan and seems to only put the device in a kind of listening mode (beacon/probe-response) for software scan. Since no probe request are generated by the software, current scanning method is similar to a passive scan. This patch introduces support for 'true' hardware offloaded scan. Hardware scan is configured and started via the start-scan-offload firmware message. Once scan has been completed a scan indicator message is received from firmware. Moreover, this patch includes support for directed probe-request, allowing connection with hidden APs. It also fixes scan issues with band-steering AP which are not 'visible' with passive scan (due to hidden ssid in beacons). Let's keep the 'legacy' scanning method in case scan-offload is not supported. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-11-20wcn36xx: fix iris child-node lookupJohan Hovold
Fix child-node lookup during probe, which ended up searching the whole device tree depth-first starting at the parent rather than just matching on its children. To make things worse, the parent mmio node was also prematurely freed. Fixes: fd52bdae9ab0 ("wcn36xx: Disable 5GHz for wcn3620") Cc: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-11-04Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.15 Mostly fixes this time, but also few new features. Major changes: wil6210 * remove ssid debugfs file rsi * add WOWLAN support for suspend, hibernate and shutdown states ath10k * add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware where it's supported (QCA99x0 and QCA4019) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27wcn36xx: Remove unnecessary rcu_read_unlock in wcn36xx_bss_info_changedJia-Ju Bai
No rcu_read_lock is called, but rcu_read_unlock is still called. Thus rcu_read_unlock should be removed. Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-09-25wcn36xx: Disable 5GHz for wcn3620Loic Poulain
wcn3620 can only operate on 2.4GHz band due to RF limitation. If wcn36xx digital block is associated with an external IRIS RF module, retrieve the id and disable 5GHz band in case of wcn3620 id. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-08-08wcn36xx: Introduce mutual exclusion of fw configurationBjorn Andersson
As the association status changes the driver needs to configure the hardware. This is done based on information in the "sta" acquired by ieee80211_find_sta(), which requires the caller to ensure that the "sta" is valid while its being used; generally by entering an rcu read section. But the operations acting on the "sta" has to communicate with the firmware and may therefor sleep, resulting in the following report: [ 31.418190] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238 [ 31.425919] in_atomic(): 0, irqs_disabled(): 0, pid: 34, name: kworker/u8:1 [ 31.434609] CPU: 0 PID: 34 Comm: kworker/u8:1 Tainted: G W 4.12.0-rc4-next-20170607+ #993 [ 31.441002] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT) [ 31.450380] Workqueue: phy0 ieee80211_iface_work [ 31.457226] Call trace: [ 31.461830] [<ffffff8008088c58>] dump_backtrace+0x0/0x260 [ 31.464004] [<ffffff8008088f7c>] show_stack+0x14/0x20 [ 31.469557] [<ffffff8008392e70>] dump_stack+0x98/0xb8 [ 31.474592] [<ffffff80080e4330>] ___might_sleep+0xf0/0x118 [ 31.479626] [<ffffff80080e43a8>] __might_sleep+0x50/0x88 [ 31.485010] [<ffffff80088ff9a4>] mutex_lock+0x24/0x60 [ 31.490479] [<ffffff8008595c38>] wcn36xx_smd_set_link_st+0x30/0x130 [ 31.495428] [<ffffff8008591ed8>] wcn36xx_bss_info_changed+0x148/0x448 [ 31.501504] [<ffffff80088ab3c4>] ieee80211_bss_info_change_notify+0xbc/0x118 [ 31.508102] [<ffffff80088f841c>] ieee80211_assoc_success+0x664/0x7f8 [ 31.515220] [<ffffff80088e13d4>] ieee80211_rx_mgmt_assoc_resp+0x144/0x2d8 [ 31.521555] [<ffffff80088e1e20>] ieee80211_sta_rx_queued_mgmt+0x190/0x698 [ 31.528239] [<ffffff80088bc44c>] ieee80211_iface_work+0x234/0x368 [ 31.535011] [<ffffff80080d81ac>] process_one_work+0x1cc/0x340 [ 31.541086] [<ffffff80080d8368>] worker_thread+0x48/0x430 [ 31.546814] [<ffffff80080de448>] kthread+0x108/0x138 [ 31.552195] [<ffffff8008082ec0>] ret_from_fork+0x10/0x50 In order to ensure that the "sta" remains alive (and consistent) for the duration of bss_info_changed() mutual exclusion has to be ensured with sta_remove(). This is done by introducing a mutex to cover firmware configuration changes, which is made to also ensure mutual exclusion between other operations changing the state or configuration of the firmware. With this we can drop the rcu read lock. Cc: stable@vger.kernel.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-05-23wcn36xx: Close SMD channel on device removalBjorn Andersson
The SMD channel is not the primary WCNSS channel and must explicitly be closed as the device is removed, or the channel will already by open on a subsequent probe call in e.g. the case of reloading the kernel module. This issue was introduced because I simplified the underlying SMD implementation while the SMD adaptions of the driver sat on the mailing list, but missed to update these patches. The patch does however only apply back to the transition to rpmsg, hence the limited Fixes. Fixes: 5052de8deff5 ("soc: qcom: smd: Transition client drivers from smd to rpmsg") Reported-by: Eyal Ilsar <c_eilsar@qti.qualcomm.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-20Merge tag 'mac80211-next-for-davem-2017-04-18' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== My last pull request has been a while, we now have: * connection quality monitoring with multiple thresholds * support for FILS shared key authentication offload * pre-CAC regulatory compliance - only ETSI allows this * sanity check for some rate confusion that hit ChromeOS (but nobody else uses it, evidently) * some documentation updates * lots of cleanups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-09Merge tag 'wireless-drivers-next-for-davem-2017-04-07' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.12 Lots of bugfixes as usual but also some new features. Major changes: ath10k * improve firmware download time for QCA6174 and QCA9377, especially helps resume time ath9k_htc * add support AirTies 1eda:2315 AR9271 device rt2x00 * add support MT7620 mwifiex * enable auto deep sleep mode for USB chipsets brcmfmac * add support for network namespaces (WIPHY_FLAG_NETNS_OK) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-28soc: qcom: smd: Transition client drivers from smd to rpmsgBjorn Andersson
By moving these client drivers to use RPMSG instead of the direct SMD API we can reuse them ontop of the newly added GLINK wire-protocol support found in the 820 and 835 Qualcomm platforms. As the new (RPMSG-based) and old SMD implementations are mutually exclusive we have to change all client drivers in one commit, to make sure we have a working system before and after this transition. Acked-by: Andy Gross <andy.gross@linaro.org> Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-09wcn36xx: Fix error handlingChristophe Jaillet
Reorder 'out_free_dxe_pool' and 'out_free_dxe_ctl' error handling labels in order to match the way resources have been allocated. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-03-06wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple driversAndrew Zaborowski
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature wholesale in all mac80211-based drivers that do not set the IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and will detect when the thresholds set by ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few) drivers need code to enable the firmware to monitor the thresholds. This is mostly only compile-tested. Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-02-07wcn36xx: Implement cancel_hw_scanBjorn Andersson
In the even that the wcn36xx interface is brought down while a hw_scan is active we must abort and wait for the ongoing scan to signal completion to mac80211. Reported-by: Mart Raudsepp <leio@gentoo.org> Fixes: 886039036c20 ("wcn36xx: Implement firmware assisted scan") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-12wcn36xx: Don't use the destroyed hal_mutexBjorn Andersson
ieee80211_unregister_hw() might invoke operations to stop the interface, that uses the hal_mutex. So don't destroy it until after we're done using it. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-12wcn36xx: Implement firmware assisted scanBjorn Andersson
Using the software based channel scan mechanism from mac80211 keeps us offline for 10-15 second, we should instead issue a start_scan/end_scan on each channel reducing this time. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-12wcn36xx: Transition driver to SMD clientBjorn Andersson
The wcn36xx wifi driver follows the life cycle of the WLAN_CTRL SMD channel, as such it should be a SMD client. This patch makes this transition, now that we have the necessary frameworks available. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit v1.2.3-70-g09d2 (git 2.48.1) at 2025-09-09 21:40:29 +0000