Age | Commit message (Collapse) | Author |
|
These entries are not used, remove them.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240605140327.0c7c520814d5.I19cefb3d81b03a5be94c029cfffd1c8b8c437182@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have
two conflicts this time:
net/mac80211/cfg.c
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au
drivers/net/wireless/microchip/wilc1000/netdev.c
https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA)
support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
* tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits)
wifi: ath12k: add hw_link_id in ath12k_pdev
wifi: ath12k: add panic handler
wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity()
wifi: brcm80211: remove unused structs
wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)
wifi: ath12k: do not process consecutive RDDM event
dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example
wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup()
wifi: rtlwifi: handle return value of usb init TX/RX
wifi: rtlwifi: Enable the new rtl8192du driver
wifi: rtlwifi: Add rtl8192du/sw.c
wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg
wifi: rtlwifi: Add rtl8192du/dm.{c,h}
wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h}
wifi: rtlwifi: Add rtl8192du/rf.{c,h}
wifi: rtlwifi: Add rtl8192du/trx.{c,h}
wifi: rtlwifi: Add rtl8192du/phy.{c,h}
wifi: rtlwifi: Add rtl8192du/hw.{c,h}
wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU
wifi: rtlwifi: Add rtl8192du/table.{c,h}
...
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In beacon template version 14, make sure to always set
the TWT IE offset before sending the beacon template command,
also in the debugfs inject_beacon_ie path.
If the TWT IE does not exist, the offset will be set to zero.
Fixes: bf0212fd8faa ("wifi: iwlwifi: mvm: add beacon template version 14")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512152312.eb27175c345a.If30ef24aba10fe47fd42a7a9703eb8903035e294@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The firmware prefix is unused today, but it might still be
useful to have some information. Since the prefix will get
the intel/ directory in some cases, replace the prefix by
the full FW id which has all the information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.527a1c72996d.If7588b854149d51605031fc9a70a650534351ef4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a debugfs option to use the ptp clock time for rx device
timestamps. This can be useful to e.g. synchronize multiple NICs or
reporting the timestamp in the system clock instead of gp2.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240527190228.b197b4f3f9ed.I578ee916d5f517a2e3a89e890a8ea24065946427@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When we crash the firmware, we need to know why we decided to do so.
Almost all the callsites of iwl_force_nmi() print something in the logs
that explain why the driver decided to crash the firmware.
Debugfs doesn't print anything and it is then hard to understand why the
firmware has crashed.
Add a simple print in the debugfs hook to ease the debug.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512075822.e2558de222dc.Idd81777c47264e6f557b086625895c1dc2f667f3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
dmi_get_system_info() will statically return NULL when the
kernel is compiled without CONFIG_DMI, leading to compiler
warnings. Fix that by printing "<unknown>" in that case.
Fixes: c3f40c3e0273 ("iwlwifi: mvm: add US/CA to TAS block list if OEM isn't allowed")
Fixes: 9457077df49e ("wifi: iwlwifi: mvm: Add debugfs to get TAS status")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For each DSM function, try to first read it from the UEFI.
If the UEFI WIFI GUID is unclocked, or the DSM function in
UEFI is invalid/unavailable - read it from ACPI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.27dd626ce2bd.Ib90bab74a9d56deb2362edb712294360e4ddae5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As DSMs are going to be read from UEFI too, we need a unified API
to get DSMs for both ACPI and UEFI.
The difference in getting DSM in each one of these methods (ACPI, UEFI)
is in the GUID, revision (0 for ACPI, 4 for UEFI), and size of the DSM
values (8 or 32 for ACPI, 32 for UEFI).
Therefore, change the iwl_acpi_get_dsm_x() to iwl_acpi_get_dsm() which
determines the GUID, revision (these two are the same for all WiFi DSMs),
and size (based on a func-to-size mapping) internally.
While at it, fix DSM_FUNC_RFI_CONFIG to expect a 32-bit value
(as defined in Intel BIOS spec) and not a 8-bit one.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1bcd7072a7a5.I344ee0a11abbc27da0c693187d1b8bee653aaeef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We are going to support reading BIOS tables from UEFI
too, Refactor the TAS table flow:
1. Rename and move the common code to the regulatory.h/c files.
2. Remove the IWL_TAS_BLOCK_LIST_MAX, as we can use IWL_WTAS_BLACK_LIST_MAX
instead.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.0c2197cf1feb.Ib0e83d5bd3f4d5cfa9c3d2925317ba49377d257f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ENOTSUPP isn't a standard error code, don't use it. Replace with
EOPNOTSUPP instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.a69f4347b5f8.I88429d5de8251287ec0b58ff26a588465b9049a5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver copies the userspace buffer into an internal NUL
byte terminated buffer. While doing so, it was reading beyond
the end of the userspace buffer, overwriting its own NUL
termination in the process.
Fix this by only copying the correct number of bytes.
Fixes: 3f244876ef73 ("wifi: iwlwifi: make debugfs entries link specific")
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231219215605.e4913deb2ad4.Idcf6a7e909ff4b7801cd49c2f691f84a2f68eff9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This can be used by the user space when it wants to clear the data we
collected so far for privacy reasons.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231207044813.d5e97d5ec0d9.I7a5e836e6109e1fce7e6301dba8d1f28e60a5440@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add debgufs handler for fw system statistics command.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231022173519.e77efee7cd85.I99f370f26f94f73e06aec2a8eaf21ebcc82f60a9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mac_ctdp_sum contains the power consumption, appears in power save
report, and is used for debugging and collection of statistics.
Add a debugfs handler to start this calculation, iff ctdp
command is supported in the firmware.
While on it, add an option to force start/stop this calculation,
which is safe from the firmware API side.
Signed-off-by: iallouch <itai.allouche@intel.com>
Signed-off-by: Nitsan Bar <nitsan.bar@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.024d75df9e03.I69fdc826f2931a6e1435b450f0602ea060704697@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
All the configurations for the various Bz/Gl devices
are basically identical, except for Gl A-step and the
firmware filename prefixes.
Add some infrastructure to auto-generate the firmware
filename prefix based on the detected MAC step and
RF name/step, and remove all the unneeded configs.
This reduces the size of the iwlwifi module by ~9k:
517582 27111 560 545253 851e5 drivers/net/wireless/intel/iwlwifi/iwlwifi.ko
526885 27083 560 554528 87620 drivers/net/wireless/intel/iwlwifi/iwlwifi.ko
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230621130443.1dc121ba338f.I07d651516eb82cbaded4724ef30558a50f2fa866@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
All of the station elements are really elements for the link. Create
them from the correct callback and return the link specific information
rather than always using the default link.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230612184434.a8e0c40d325e.I374d9433c3b8694667e1ce550d65f6f1f0d23c05@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Check the firmware response size for responses to the
memory read/write command in debugfs before using it.
Fixes: 2b55f43f8e47 ("iwlwifi: mvm: Add mem debugfs entry")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.0d56fcaf68ee.I70e9571f3ed7263929b04f8fabad23c9b999e4ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to simplify checking that this value was set up
correctly, add it to debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.c9a787710e1e.If509b2e510e22d62f3eefb2c54ff1645e331dc23@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Driver uses link_id as an index in the array. FW currently can
support only 2 concurrently active links per vif with the ids in the
range 0-3. Add a mapping of dirver link ids to fw link id and track the
number of active link ids.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104949.a53e5df49c33.I02b25648d2d5ca370c0697bf19d0d34724eae8a1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
HE/EHT support is reported to FW if there's at least one link
that supports it. Configure beacon separately for each link.
Don't send the beacon template before adding the MAC.
Co-developed-by: Johannes Berg <johannes.berg@intel.com>
Co-developed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104949.5ef4efeda2dd.I6ebda2b71c964b9aa63240c9fa1ee0d28099fe6e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Split iwl_mvm_sta into general and link specific parts. As a first
step, all link dependent parameters reside in deflink.
The change was done mostly using the spatch below with some manual
adjustments.
@iwl_mvm_sta@
struct iwl_mvm_sta *s;
identifier var = {sta_id, lq_sta, avg_energy};
@@
(
s->
- var
+ deflink.var
)
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104948.34eace06d583.I1f8c5e919a71b21030460fbdd220d42401b688b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add debugfs file in mvm to retrieve TAS status per LMAC,
TAS block list, current mcc, OEM name and OEM allowed list.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.8efc8c41efae.I94e1a6efb9c33e2cdbcf4bf3ed2384005397dee9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch addresses the error from checkpatch.pl regarding the presence
of prohibited spaces.
Signed-off-by: Solomon Tan <solomonbstoner@protonmail.ch>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.557d6841a166.I0957923fe9ea20c1ec9140477033548ccfe93e9a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0aa0 ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230127002430.a25158d58fd7.Ibfe217f12a63c1d5349218e74c4b802c70c13c7c@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
|
|
When setting the rate for Tx, the code tried to get the lowest
allowed rate but without considering the BSS basic rates. Fix this
by considering the basic rates.
In addition, declare support for configuring beacon Tx rate and when
configured use the configured Tx beacon rate to set beacon tx command rate.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221102165239.be8403f0d5c0.I7d141646746b96310efd75fc77ca9aebc61aefcc@changeid
|
|
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When "debugfs=off" is used on the kernel command line, iwiwifi's
mvm module uses an invalid/unchecked debugfs_dir pointer and causes
a BUG:
BUG: kernel NULL pointer dereference, address: 000000000000004f
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 503 Comm: modprobe Tainted: G W 5.17.0-rc5 #7
Hardware name: Dell Inc. Inspiron 15 5510/076F7Y, BIOS 2.4.1 11/05/2021
RIP: 0010:iwl_mvm_dbgfs_register+0x692/0x700 [iwlmvm]
Code: 69 a0 be 80 01 00 00 48 c7 c7 50 73 6a a0 e8 95 cf ee e0 48 8b 83 b0 1e 00 00 48 c7 c2 54 73 6a a0 be 64 00 00 00 48 8d 7d 8c <48> 8b 48 50 e8 15 22 07 e1 48 8b 43 28 48 8d 55 8c 48 c7 c7 5f 73
RSP: 0018:ffffc90000a0ba68 EFLAGS: 00010246
RAX: ffffffffffffffff RBX: ffff88817d6e3328 RCX: ffff88817d6e3328
RDX: ffffffffa06a7354 RSI: 0000000000000064 RDI: ffffc90000a0ba6c
RBP: ffffc90000a0bae0 R08: ffffffff824e4880 R09: ffffffffa069d620
R10: ffffc90000a0ba00 R11: ffffffffffffffff R12: 0000000000000000
R13: ffffc90000a0bb28 R14: ffff88817d6e3328 R15: ffff88817d6e3320
FS: 00007f64dd92d740(0000) GS:ffff88847f640000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000004f CR3: 000000016fc79001 CR4: 0000000000770ee0
PKRU: 55555554
Call Trace:
<TASK>
? iwl_mvm_mac_setup_register+0xbdc/0xda0 [iwlmvm]
iwl_mvm_start_post_nvm+0x71/0x100 [iwlmvm]
iwl_op_mode_mvm_start+0xab8/0xb30 [iwlmvm]
_iwl_op_mode_start+0x6f/0xd0 [iwlwifi]
iwl_opmode_register+0x6a/0xe0 [iwlwifi]
? 0xffffffffa0231000
iwl_mvm_init+0x35/0x1000 [iwlmvm]
? 0xffffffffa0231000
do_one_initcall+0x5a/0x1b0
? kmem_cache_alloc+0x1e5/0x2f0
? do_init_module+0x1e/0x220
do_init_module+0x48/0x220
load_module+0x2602/0x2bc0
? __kernel_read+0x145/0x2e0
? kernel_read_file+0x229/0x290
__do_sys_finit_module+0xc5/0x130
? __do_sys_finit_module+0xc5/0x130
__x64_sys_finit_module+0x13/0x20
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f64dda564dd
Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1b 29 0f 00 f7 d8 64 89 01 48
RSP: 002b:00007ffdba393f88 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f64dda564dd
RDX: 0000000000000000 RSI: 00005575399e2ab2 RDI: 0000000000000001
RBP: 000055753a91c5e0 R08: 0000000000000000 R09: 0000000000000002
R10: 0000000000000001 R11: 0000000000000246 R12: 00005575399e2ab2
R13: 000055753a91ceb0 R14: 0000000000000000 R15: 000055753a923018
</TASK>
Modules linked in: btintel(+) btmtk bluetooth vfat snd_hda_codec_hdmi fat snd_hda_codec_realtek snd_hda_codec_generic iwlmvm(+) snd_sof_pci_intel_tgl mac80211 snd_sof_intel_hda_common soundwire_intel soundwire_generic_allocation soundwire_cadence soundwire_bus snd_sof_intel_hda snd_sof_pci snd_sof snd_sof_xtensa_dsp snd_soc_hdac_hda snd_hda_ext_core snd_soc_acpi_intel_match snd_soc_acpi snd_soc_core btrfs snd_compress snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_hda_codec raid6_pq iwlwifi snd_hda_core snd_pcm snd_timer snd soundcore cfg80211 intel_ish_ipc(+) thunderbolt rfkill intel_ishtp ucsi_acpi wmi i2c_hid_acpi i2c_hid evdev
CR2: 000000000000004f
---[ end trace 0000000000000000 ]---
Check the debugfs_dir pointer for an error before using it.
Fixes: 8c082a99edb9 ("iwlwifi: mvm: simplify iwl_mvm_dbgfs_register")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220223030630.23241-1-rdunlap@infradead.org
[change to make both conditional]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no point spelling out the same condition twice,
so remove the second one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220204122220.321a7e67209b.Iafb75006eab971ca6982d6efd76347d3f47bd023@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Avoid void pointer arithmetic since it's technically
undefined and causes warnings in some places that use
our code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.e349104ecd94.Iadc937f475158b9437becdfefb361a97e7eaa934@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The order of arguments for iwl_cmd_id() is confusing, and the
version is always 0 and thus a useless argument. Prefer the
WIDE_ID() macro (which needs to be a macro due to use in switch
cases etc.) over the iwl_cmd_id() function.
Obviously done with spatch:
@@
expression G, C;
@@
-iwl_cmd_id(C, G, 0)
+WIDE_ID(G, C)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.cc4f9d1a2e9b.Ieb023cd773ea22e819d1ef1c37ae857ecc1a839d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This feature has been deprecated and should not be used anymore. With
newer firmwares, namely *-67.ucode and above, trying to use it causes an
assertion failure in the FW, similar to this:
[Tue Jan 11 20:05:24 2022] iwlwifi 0000:04:00.0: 0x00001062 | ADVANCED_SYSASSERT
In order to prevent this feature from being used, remove it entirely
and get rid of the Kconfig option that
enables it (IWLWIFI_BCAST_FILTERING).
Fixes: cbaa6aeedee5 ("iwlwifi: bump FW API to 67 for AX devices")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215488
Cc: stable@vger.kernel.org # 5.16.x
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128144623.9241e049f13e.Ia4f282813ca2ddd24c13427823519113f2bbebf2@changeid
|
|
We forgot to link this to debugfs, so the code is all dead.
Add it for real.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20211219110000.d0f314101410.I7357c01179c35621686265d4da4a64d2333a5f1a@changeid
|
|
Normally, when we hit an assert, we print out all the
assert data. However, in certain tests, when we trigger
it from debugfs intentionally, that can be useless and
confusing.
Allow writing the string "nolog\n" to the fw_nmi and
fw_restart files suppressing the assert dump as well
as - in the case of fw_restart - the
iwlwifi 0000:00:00.0: FW error in SYNC CMD REPLY_ERROR
message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204174546.75e29a2ab68d.Id3064feda2ce7a77c116c6d6e71ce5ff447c6e86@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As part of the new rate_n_flags, a new version of
BEACON_TEMPLATE_CMD was added in FW in order to support
the new rate_n_flags.
Add support for the new version.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.b42e67f14293.Ic3f1ed8cb3a31cfaa51174497dd993936b00d398@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As part of the new rate_n_flags, tx_cmd API has changed.
Add support for these changes.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.26efa51624b1.Ic96ae4d81b3ff07fb514df2b5f6a8e470e4d3778@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As part of the new rate_n_flags, a new version of tlc_update_notif
was added in FW in order to support the new rate_n_flags.
Add support for the new version, and move the all API to use the
new rate_n_flags only (if FW supports the old one - convert it).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017123741.9fc0cb5d5898.I1f88e02317f79f1be7f792c01236d836045a44b3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Since antenna c is not in use and won't be relevant after the new rate &
flags, remove all it's references
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017113927.5e39106ec75b.I4281edc844f734bf9591396a5cc8009ad37ccda8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The GEO profiles have been stored in single-dimension arrays and the
access has been done via a single index. We will soon need to support
different revisions of this table, which will make the flat array even
harder to handle. To prepare for that, convert the single-dimension
array to a struct with substructures.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.56f3506411a2.I600ed3708d19f2263a5a8d143f6711d08499bbb0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For IWL_DEVICE_FAMILY_22000 & greater, driver will call
NMI instead of REPLY_ERROR as FW->Infra does not support
this command for this family onwards.
Signed-off-by: Harish Mitty <harish.mitty@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.597f4246c79d.Ia0a1bbc2e66b4e849174db685208fc2b8bd5732e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We cannot lock a mutex while we're in an RCU critical section. At
the same time, we're accessing data structures that are protected
by the mvm->mutex anyway, so just move the entire locking here to
use only that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.4d27bd36e10e.I1fd8e8fe442c41a5deaa560452b598ed7a60ada5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The mutex is already locked in iwl_mvm_mac_start.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Fixes: 21254908cbe9 ("iwlwifi: mvm: add RFI-M support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.703288ea058d.I82a0312389032d07c3b478bef3e938e06bfa7df6@changeid
|
|
No need to pass the dbgfs_dir just to assign it to mvm.
Assign to mvm and then call iwl_mvm_dbgfs_register.
This is a preparation towards the addition of a delayed
op_mode_start flow.
This will allow to split the op_mode_start flow.
Registration to debugfs must happen after we register to
mac80211 and the registration to mac80211 will soon be
delayed in certain cases. In order not to have to remember
the debugfs_dir in a separate variable, just set it into
the mvm structure so that it can be usable later.
Declare mvm->debugfs_dir in the iwl_mvm structure even when
IWLWIFI_DEBUGFS isn't enabled to simplify the source code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.a92ee491863d.I047923aa3598fbf4fb6fce2cdff75a4969fedd76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
RF Interference Mitigation is a new feature targeted to handle the
problem of interference between DDR memory and WiFi. The role of
the driver is to configure FW with the table holding a mapping
between problematic channels/bands and the corresponding frequencies.
This patch adds RFI infrastructure and adds two debugfs hooks:
- send RFI configuration command (currently with a default table) which
will reset feature in the FW
- read the table, used by the FW (which can be a subset of the table
that driver sent).
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.2cea55a09bc7.I634b79795abad499ce442631d6672ffef8fc6d41@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is used for different tests collecting different types of
debug data from fw (e.g latency issues, hw issues etc).
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210131201908.0db829694810.I001f39d34ae46c87870d9bd94a4baaa3250578d1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we check the length, we only check that the advertised
data length fits into the data we have, but currently not
that it actually matches correctly.
This should be harmless, but if the first two bytes are zero,
then the iwl_rx_packet_payload_len() ends up negative, and
that might later cause issues if unsigned variables are used,
as this is not something that's normally expected.
Change the validation here to precisely validate the lengths
match, to avoid such issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.5184dfc2a445.I0631d2e4f6ffb93cf06618edb035c45bd6d1d7b9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add debugfs file to print the PHY integration version.
File name is: phy_integration_ver
Signed-off-by: Dror Moshe <drorx.moshe@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.f5127d919656.Ib714f444390b39cbbf7eb143c5440cc890385981@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the new api all the flush in the FW is done before we
get the response and in the response we only get the updated
read pointer and all queued packets don't get anymore rx_tx
per packet to free the queued packet, so driver needs to free
all queued packets on flushed queue at once after flush response.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4bd0eca8c0ef.I1601aad2eb2cc83f6f73b8ca52be57bb9fd626ab@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|