| Age | Commit message (Collapse) | Author |
|---|
|
The iwlwifi wireless driver registers a thermal zone that is only needed
when the network interface handled by it is up and it wants that thermal
zone to be effectively ignored by the core otherwise.
Before commit a8a261774466 ("thermal: core: Call monitor_thermal_zone()
if zone temperature is invalid") that could be achieved by returning
an error code from the thermal zone's .get_temp() callback because the
core did not really handle errors returned by it almost at all.
However, commit a8a261774466 made the core attempt to recover from the
situation in which the temperature of a thermal zone cannot be
determined due to errors returned by its .get_temp() and is always
invalid from the core's perspective.
That was done because there are thermal zones in which .get_temp()
returns errors to start with due to some difficulties related to the
initialization ordering, but then it will start to produce valid
temperature values at one point.
Unfortunately, the simple approach taken by commit a8a261774466,
which is to poll the thermal zone periodically until its .get_temp()
callback starts to return valid temperature values, is at odds with
the special thermal zone in iwlwifi in which .get_temp() may always
return an error because its network interface may always be down. If
that happens, every attempt to invoke the thermal zone's .get_temp()
callback resulting in an error causes the thermal core to print a
dev_warn() message to the kernel log which is super-noisy.
To address this problem, make the core handle the case in which
.get_temp() returns 0, but the temperature value returned by it
is not actually valid, in a special way. Namely, make the core
completely ignore the invalid temperature value coming from
.get_temp() in that case, which requires folding in
update_temperature() into its caller and a few related changes.
On the iwlwifi side, modify iwl_mvm_tzone_get_temp() to return 0
and put THERMAL_TEMP_INVALID into the temperature return memory
location instead of returning an error when the firmware is not
running or it is not of the right type.
Also, to clearly separate the handling of invalid temperature
values from the thermal zone initialization, introduce a special
THERMAL_TEMP_INIT value specifically for the latter purpose.
Fixes: a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid")
Closes: https://lore.kernel.org/linux-pm/20240715044527.GA1544@sol.localdomain/
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201761
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: 6.10+ <stable@vger.kernel.org> # 6.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/4950004.31r3eYUQgx@rjwysocki.net
[ rjw: Rebased on top of the current mainline ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Not much excitement - a handful of large patchsets (devmem among them)
did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at
socket init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow
synchronizing hashing of two routers, and preventing partial
accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states.
Userspace IKE daemon had to do this before, but the kernel can
better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the
sampled traffic from "upcall" packets sent to user space for
forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head
- Support resilient split BTF which cuts down on duplication and
makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables
both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument
support for BPF trampolines and to utilize bpf_prog_pack for the
latter
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration
changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI
tools)
Drivers:
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead and
skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps to
catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead
of in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
tcp: Replace strncpy() with strscpy()
wifi: ath12k: fix build vs old compiler
tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
eth: fbnic: Add L2 address programming
eth: fbnic: Add basic Rx handling
eth: fbnic: Add basic Tx handling
eth: fbnic: Add link detection
eth: fbnic: Add initial messaging to notify FW of our presence
eth: fbnic: Implement Rx queue alloc/start/stop/free
eth: fbnic: Implement Tx queue alloc/start/stop/free
eth: fbnic: Allocate a netdevice and napi vectors with queues
eth: fbnic: Add FW communication mechanism
eth: fbnic: Add message parsing for FW messages
eth: fbnic: Add register init to set PCIe/Ethernet device config
eth: fbnic: Allocate core device specific structures and devlink interface
eth: fbnic: Add scaffolding for Meta's NIC driver
PCI: Add Meta Platforms vendor ID
net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
...
|
|
Out of several drivers implementing the .set_trip_temp() thermal zone
operation, three don't actually use the trip ID argument passed to it,
two call __thermal_zone_get_trip() to get a struct thermal_trip
corresponding to the given trip ID, and the other use the trip ID as an
index into their own data structures with the assumption that it will
always match the ordering of entries in the trips table passed to the
core during thermal zone registration, which is fragile and not really
guaranteed.
Even though the trip IDs used by the core are in fact their indices in the
trips table passed to it by the thermal zone creator, that is purely a
matter of convenience and should not be relied on for correctness.
For this reason, modify trip_point_temp_store() to pass a (const) trip
pointer to .set_trip_temp() and adjust the drivers implementing it
accordingly.
This helps to simplify the drivers invoking __thermal_zone_get_trip()
from their .set_trip_temp() callback functions because they will not
need to do it now and the other drivers can store their internal
trip indices in the priv field in struct thermal_trip and their
.set_trip_temp() callback functions can get those indices from there.
The intel_quark_dts thermal driver can instead use the trip type to
determine the requisite trip index.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/8392906.T7Z3S40VBb@rjwysocki.net
[ rjw: Add missing colon and 2 empty code lines ]
[ rjw: Add missing change in imx_thermal.c and adjust the changelog ]
[ rjw: Drop an unused local variable ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This will allow to suspend / resume the system without resetting the
firmware. This will allow to reduce the resume time.
In case the fast_resume fails, stop the device and bring it up from
scratch.
Raise the timeout for the D3_END notification since in some iterations,
it took 240ms.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240618194245.03b8d2801044.I613d17c712de7a0d611cde4e14f37ebbe0c3c964@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add and use an mvm-specific guard for the mvm mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512152312.7391425b3af2.I1b109f56753dd3f35602dd2c5cf6e1e35aee313d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
All of the thermal_zone_device_register_with_trips() callers pass zero
writable trip points masks to it, so drop the mask argument from that
function and update all of its callers accordingly.
This also removes the artificial trip points per zone limit of 32,
related to using writable trip points masks.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
It is now possible to flag trip points with THERMAL_TRIP_FLAG_RW_TEMP
to allow their temperature to be set from user space via sysfs instead
of using a nonzero writable trips mask during thermal zone registration,
so make the iwlwifi code do that.
No intentional functional impact.
Note that this change is requisite for dropping the mask argument from
thermal_zone_device_register_with_trips() going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The code walking trip points in iwl_mvm_send_temp_report_ths_cmd()
reads the trip table passed to thermal_zone_device_register_with_trips()
in order to get the current trip temperatures, but this is not
guaranteed to work in the future, because the thermal zone will store
trip points information internally.
For this reason, make iwl_mvm_send_temp_report_ths_cmd() use
for_each_thermal_trip() as appropriate for walking trip points in a
given thermal zone.
No intentional functional impact, but it is requisite for future thermal
core improvements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miri Korenblit <Miriam.rachel.korenblit@intel.com>
|
|
The trip table in iwl_mvm_thermal_zone_register() is populated after
passing it to thermal_zone_device_register_with_trips(), so it may be
accessed (for instance, via sysfs) before it is ready.
To prevent that from happening, modify the function to populate the
trip table before calling thermal_zone_device_register_with_trips().
Also make the code use THERMAL_TEMP_INVALID as the "invalid temperature"
value which is also meaningful for the core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miri Korenblit <Miriam.rachel.korenblit@intel.com>
|
|
The fw_trips_index[] array in struct iwl_mvm_thermal_device is only
populated, but never read, so drop it.
Note that the iwl_mvm_send_temp_report_ths_cmd() code populating
fw_trips_index[] is questionable, because it accesses a trips table
of a thermal zone directly, which is not guaranteed to work in the
future.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miri Korenblit <Miriam.rachel.korenblit@intel.com>
|
|
Since 'tz_device' is an in-place member of 'struct iwl_mvm', it can't
be NULL and so relevant check may be dropped. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231003092048.24998-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Introduce a config option to tweak MAX_SKB_FRAGS. Increasing the
default value allows for better BIG TCP performances
- Reduce compound page head access for zero-copy data transfers
- RPS/RFS improvements, avoiding unneeded NET_RX_SOFTIRQ when
possible
- Threaded NAPI improvements, adding defer skb free support and
unneeded softirq avoidance
- Address dst_entry reference count scalability issues, via false
sharing avoidance and optimize refcount tracking
- Add lockless accesses annotation to sk_err[_soft]
- Optimize again the skb struct layout
- Extends the skb drop reasons to make it usable by multiple
subsystems
- Better const qualifier awareness for socket casts
BPF:
- Add skb and XDP typed dynptrs which allow BPF programs for more
ergonomic and less brittle iteration through data and
variable-sized accesses
- Add a new BPF netfilter program type and minimal support to hook
BPF programs to netfilter hooks such as prerouting or forward
- Add more precise memory usage reporting for all BPF map types
- Adds support for using {FOU,GUE} encap with an ipip device
operating in collect_md mode and add a set of BPF kfuncs for
controlling encap params
- Allow BPF programs to detect at load time whether a particular
kfunc exists or not, and also add support for this in light
skeleton
- Bigger batch of BPF verifier improvements to prepare for upcoming
BPF open-coded iterators allowing for less restrictive looping
capabilities
- Rework RCU enforcement in the verifier, add kptr_rcu and enforce
BPF programs to NULL-check before passing such pointers into kfunc
- Add support for kptrs in percpu hashmaps, percpu LRU hashmaps and
in local storage maps
- Enable RCU semantics for task BPF kptrs and allow referenced kptr
tasks to be stored in BPF maps
- Add support for refcounted local kptrs to the verifier for allowing
shared ownership, useful for adding a node to both the BPF list and
rbtree
- Add BPF verifier support for ST instructions in
convert_ctx_access() which will help new -mcpu=v4 clang flag to
start emitting them
- Add ARM32 USDT support to libbpf
- Improve bpftool's visual program dump which produces the control
flow graph in a DOT format by adding C source inline annotations
Protocols:
- IPv4: Allow adding to IPv4 address a 'protocol' tag. Such value
indicates the provenance of the IP address
- IPv6: optimize route lookup, dropping unneeded R/W lock acquisition
- Add the handshake upcall mechanism, allowing the user-space to
implement generic TLS handshake on kernel's behalf
- Bridge: support per-{Port, VLAN} neighbor suppression, increasing
resilience to nodes failures
- SCTP: add support for Fair Capacity and Weighted Fair Queueing
schedulers
- MPTCP: delay first subflow allocation up to its first usage. This
will allow for later better LSM interaction
- xfrm: Remove inner/outer modes from input/output path. These are
not needed anymore
- WiFi:
- reduced neighbor report (RNR) handling for AP mode
- HW timestamping support
- support for randomized auth/deauth TA for PASN privacy
- per-link debugfs for multi-link
- TC offload support for mac80211 drivers
- mac80211 mesh fast-xmit and fast-rx support
- enable Wi-Fi 7 (EHT) mesh support
Netfilter:
- Add nf_tables 'brouting' support, to force a packet to be routed
instead of being bridged
- Update bridge netfilter and ovs conntrack helpers to handle IPv6
Jumbo packets properly, i.e. fetch the packet length from
hop-by-hop extension header. This is needed for BIT TCP support
- The iptables 32bit compat interface isn't compiled in by default
anymore
- Move ip(6)tables builtin icmp matches to the udptcp one. This has
the advantage that icmp/icmpv6 match doesn't load the
iptables/ip6tables modules anymore when iptables-nft is used
- Extended netlink error report for netdevice in flowtables and
netdev/chains. Allow for incrementally add/delete devices to netdev
basechain. Allow to create netdev chain without device
Driver API:
- Remove redundant Device Control Error Reporting Enable, as PCI core
has already error reporting enabled at enumeration time
- Move Multicast DB netlink handlers to core, allowing devices other
then bridge to use them
- Allow the page_pool to directly recycle the pages from safely
localized NAPI
- Implement lockless TX queue stop/wake combo macros, allowing for
further code de-duplication and sanitization
- Add YNL support for user headers and struct attrs
- Add partial YNL specification for devlink
- Add partial YNL specification for ethtool
- Add tc-mqprio and tc-taprio support for preemptible traffic classes
- Add tx push buf len param to ethtool, specifies the maximum number
of bytes of a transmitted packet a driver can push directly to the
underlying device
- Add basic LED support for switch/phy
- Add NAPI documentation, stop relaying on external links
- Convert dsa_master_ioctl() to netdev notifier. This is a
preparatory work to make the hardware timestamping layer selectable
by user space
- Add transceiver support and improve the error messages for CAN-FD
controllers
New hardware / drivers:
- Ethernet:
- AMD/Pensando core device support
- MediaTek MT7981 SoC
- MediaTek MT7988 SoC
- Broadcom BCM53134 embedded switch
- Texas Instruments CPSW9G ethernet switch
- Qualcomm EMAC3 DWMAC ethernet
- StarFive JH7110 SoC
- NXP CBTX ethernet PHY
- WiFi:
- Apple M1 Pro/Max devices
- RealTek rtl8710bu/rtl8188gu
- RealTek rtl8822bs, rtl8822cs and rtl8821cs SDIO chipset
- Bluetooth:
- Realtek RTL8821CS, RTL8851B, RTL8852BS
- Mediatek MT7663, MT7922
- NXP w8997
- Actions Semi ATS2851
- QTI WCN6855
- Marvell 88W8997
- Can:
- STMicroelectronics bxcan stm32f429
Drivers:
- Ethernet NICs:
- Intel (1G, icg):
- add tracking and reporting of QBV config errors
- add support for configuring max SDU for each Tx queue
- Intel (100G, ice):
- refactor mailbox overflow detection to support Scalable IOV
- GNSS interface optimization
- Intel (i40e):
- support XDP multi-buffer
- nVidia/Mellanox:
- add the support for linux bridge multicast offload
- enable TC offload for egress and engress MACVLAN over bond
- add support for VxLAN GBP encap/decap flows offload
- extend packet offload to fully support libreswan
- support tunnel mode in mlx5 IPsec packet offload
- extend XDP multi-buffer support
- support MACsec VLAN offload
- add support for dynamic msix vectors allocation
- drop RX page_cache and fully use page_pool
- implement thermal zone to report NIC temperature
- Netronome/Corigine:
- add support for multi-zone conntrack offload
- Solarflare/Xilinx:
- support offloading TC VLAN push/pop actions to the MAE
- support TC decap rules
- support unicast PTP
- Other NICs:
- Broadcom (bnxt): enforce software based freq adjustments only on
shared PHC NIC
- RealTek (r8169): refactor to addess ASPM issues during NAPI poll
- Micrel (lan8841): add support for PTP_PF_PEROUT
- Cadence (macb): enable PTP unicast
- Engleder (tsnep): add XDP socket zero-copy support
- virtio-net: implement exact header length guest feature
- veth: add page_pool support for page recycling
- vxlan: add MDB data path support
- gve: add XDP support for GQI-QPL format
- geneve: accept every ethertype
- macvlan: allow some packets to bypass broadcast queue
- mana: add support for jumbo frame
- Ethernet high-speed switches:
- Microchip (sparx5): Add support for TC flower templates
- Ethernet embedded switches:
- Broadcom (b54):
- configure 6318 and 63268 RGMII ports
- Marvell (mv88e6xxx):
- faster C45 bus scan
- Microchip:
- lan966x:
- add support for IS1 VCAP
- better TX/RX from/to CPU performances
- ksz9477: add ETS Qdisc support
- ksz8: enhance static MAC table operations and error handling
- sama7g5: add PTP capability
- NXP (ocelot):
- add support for external ports
- add support for preemptible traffic classes
- Texas Instruments:
- add CPSWxG SGMII support for J7200 and J721E
- Intel WiFi (iwlwifi):
- preparation for Wi-Fi 7 EHT and multi-link support
- EHT (Wi-Fi 7) sniffer support
- hardware timestamping support for some devices/firwmares
- TX beacon protection on newer hardware
- Qualcomm 802.11ax WiFi (ath11k):
- MU-MIMO parameters support
- ack signal support for management packets
- RealTek WiFi (rtw88):
- SDIO bus support
- better support for some SDIO devices (e.g. MAC address from
efuse)
- RealTek WiFi (rtw89):
- HW scan support for 8852b
- better support for 6 GHz scanning
- support for various newer firmware APIs
- framework firmware backwards compatibility
- MediaTek WiFi (mt76):
- P2P support
- mesh A-MSDU support
- EHT (Wi-Fi 7) support
- coredump support"
* tag 'net-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2078 commits)
net: phy: hide the PHYLIB_LEDS knob
net: phy: marvell-88x2222: remove unnecessary (void*) conversions
tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.
net: amd: Fix link leak when verifying config failed
net: phy: marvell: Fix inconsistent indenting in led_blink_set
lan966x: Don't use xdp_frame when action is XDP_TX
tsnep: Add XDP socket zero-copy TX support
tsnep: Add XDP socket zero-copy RX support
tsnep: Move skb receive action to separate function
tsnep: Add functions for queue enable/disable
tsnep: Rework TX/RX queue initialization
tsnep: Replace modulo operation with mask
net: phy: dp83867: Add led_brightness_set support
net: phy: Fix reading LED reg property
drivers: nfc: nfcsim: remove return value check of `dev_dir`
net: phy: dp83867: Remove unnecessary (void*) conversions
net: ethtool: coalesce: try to make user settings stick twice
net: mana: Check if netdev/napi_alloc_frag returns single page
net: mana: Rename mana_refill_rxoob and remove some empty lines
net: veth: add page_pool stats
...
|
|
Configure SMPS per-link. Add link_id parameter to
iwl_mvm_update_smps() and refactor iwl_mvm_intf_dual_chain_req()
since it has to handle all active links.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104949.da6a19db562c.Ic88b02338c8973f2934439ac3ee77c7451bc0054@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> #mlxsw
Acked-by: Gregory Greenman <gregory.greenman@intel.com> #iwlwifi
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> #power_supply
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> #ahci
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The thermal framework gives the possibility to register the trip
points with the thermal zone. When that is done, no get_trip_* ops are
needed and they can be removed.
The get_trip_temp, get_trip_hyst and get_trip_type are handled by the
get_trip_point().
The set_trip_temp() generic function does some checks which are no
longer needed in the set_trip_point() ops.
Convert ops content logic into generic trip points and register them
with the thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221014073253.3719911-1-daniel.lezcano@linaro.org
|
|
A new version was added to the CT-KILL notification API.
Add support for it.
In addition, print the two fields that was added in this version.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220129105618.b79be7a134e9.I7f5c67d79dd97bf5170492aab356ec983622d3b2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Instead of taking the group/command separately, make the function
take a combined command ID. In many cases, this allows us to pass
an existing command ID (e.g. cmd.id), or introduce a new variable
for it, so that we don't use the command ID twice.
This way, we can also use LONG_GROUP implicitly, so we don't need
to spell that out for many commands.
Apart from mvm.h, fw/img.{c,h} changes and some copyright and
indentation updates, this was done with spatch:
@@
identifier cmd;
expression fw, G, C, def;
@@
struct iwl_host_cmd cmd = {
.id = WIDE_ID(G, C),
...
};
...
-iwl_fw_lookup_cmd_ver(fw, G, C, def)
+iwl_fw_lookup_cmd_ver(fw, cmd.id, def)
@@
identifier cmd;
expression fw, C, def;
@@
struct iwl_host_cmd cmd = {
.id = C,
...
};
...
-iwl_fw_lookup_cmd_ver(fw, \(IWL_ALWAYS_LONG_GROUP\|LONG_GROUP\), C, def)
+iwl_fw_lookup_cmd_ver(fw, cmd.id, def)
@@
identifier func;
expression fw, G, C, mvm, flags, cmd, size, def;
type rettype;
@@
rettype func(...)
{
+u32 cmd_id = WIDE_ID(G, C);
...
-iwl_fw_lookup_cmd_ver(fw, G, C, def)
+iwl_fw_lookup_cmd_ver(fw, cmd_id, def)
...
-iwl_mvm_send_cmd_pdu(mvm, WIDE_ID(G, C), flags, cmd, size)
+iwl_mvm_send_cmd_pdu(mvm, cmd_id, flags, cmd, size)
...
}
@@
identifier func;
expression fw, G, C, mvm, flags, cmd, size, def;
type rettype;
@@
rettype func(...)
{
+u32 cmd_id = C;
...
-iwl_fw_lookup_cmd_ver(fw, \(IWL_ALWAYS_LONG_GROUP\|LONG_GROUP\), C, def)
+iwl_fw_lookup_cmd_ver(fw, cmd_id, def)
...
-iwl_mvm_send_cmd_pdu(mvm, C, flags, cmd, size)
+iwl_mvm_send_cmd_pdu(mvm, cmd_id, flags, cmd, size)
...
}
@@
expression fw, C, def;
@@
-iwl_fw_lookup_cmd_ver(fw, \(IWL_ALWAYS_LONG_GROUP\|LONG_GROUP\), C, def)
+iwl_fw_lookup_cmd_ver(fw, C, def)
@@
expression fw, C, G, def;
@@
-iwl_fw_lookup_cmd_ver(fw, G, C, def)
+iwl_fw_lookup_cmd_ver(fw, WIDE_ID(G, C), def)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220128153014.c4ac213cef5c.I6fd9a4fcbcf16ef3a3ae20a2b08ee54ebe06f96f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
thermal_notify_framework just updates for a single trip point where as
thermal_zone_device_update does other bookkeeping like updating the
temperature of the thermal zone and setting the next trip point etc.
Replace thermal_notify_framework with thermal_zone_device_update as the
later is more thorough.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210122023406.3500424-2-thara.gopinath@linaro.org
|
|
Currently, for all devices and families, failing getting the temp
from the fw is indicated in the log as ERR.
This is too severe for two reasons:
1. The driver has a fall back - and schedules the next temp
read immediately after failing to read temp from the fw.
2. The temp read implementation in the fw is different between
HWs, and on older devices the flow is a-sync and may timeout.
Reducing the print severity from ERR to WARN will allow to
track the issue if it will appear many times, but not frighten users
if it appears once.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.dfd423b2b2ef.Icd576dc3e2e7174d3ed9c1c32f48ea0013699e72@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is only needed within tt.c, make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.20a74526d395.Id24304ec1ae4b3096dbb8112bd146b364920e89e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We shouldn't trust the firmware with the sizes (or contents)
of notifications, accessing too much data could cause page
faults if the data doesn't fit into the allocated space. This
applies more on older NICs where multiple notifications can
be in a single RX buffer.
Add a general framework for checking a minimum size of any
notification in the RX handlers and use it for most. Some RX
handlers were already checking and I've moved the checks,
some more complex checks I left and made them _NO_SIZE for
the RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.3e155d5e5f90.I2121fa4ac7cd7eb98970d84b793796646afa3eed@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Use SPDX tags instead of the long copyright notices. Also cleanup
some duplicate copyright notices and combine the years where possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201210000603.481bcb512a6f.I8146abe5a637079e7336209f23cb26af98b12b31@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As part of changes made to properly support auxiliary activities in CDB
NICs, an aux sta will be added when using hot spot 2.0 and will need
to be removed when roc flow is done.
In order to do so, prepare the roc_done_wk to work synchronously as the
rm_aux_sta is a SYNC command.
Since now all of th iwl_mvm_flush_sta function are using it sync,
removed the flag argument from the function.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.71b441c8b682.Ia1d216cb680308b91d6da9f73e23ae9f4baac79f@changeid
|
|
FW is changing the max number of supported stations. To adapt to the
change we get the max number from the TLV and act according to the new
number.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.863ab470babc.I393223392f36436663c4e66add03fefe77b74e60@changeid
|
|
New API for temperature measurement (DTS_MEASUREMENT_TRIGGER)
involves getting an immediate response from FW, and not waiting
for a notification like in previous APIs. Support new API while
keeping backwards compatibility.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.b4893554d8e7.Ia4d7f389d4ac3256fcfe3ce6144e924dd6dbf6eb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
|
|
Till now, the driver asked the fw for a DTS measurement in automatic
mode. This triggered a flow in which the fw actively measured the
temperature. This is not needed anymore, as the fw performs
measurements by itself, without the driver triggering them, and the
current cadence in which the fw performs such measurements is
sufficient.
In addition, in some time-sensitive scenarios, in which the driver asks
the fw for an active measurement twice in a short time (<100ms), the fw
asserts with code 0x20100801.
Change the DTS measurement to _WITHOUT_MEASURE instead, so the fw will
respond with the last measurement it has performed.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use a unique name when registering a thermal zone. Otherwise, with
multiple NICS, we hit the following warning during the unregistration.
WARNING: CPU: 2 PID: 3525 at fs/sysfs/group.c:255
RIP: 0010:sysfs_remove_group+0x80/0x90
Call Trace:
dpm_sysfs_remove+0x57/0x60
device_del+0x5a/0x350
? sscanf+0x4e/0x70
device_unregister+0x1a/0x60
hwmon_device_unregister+0x4a/0xa0
thermal_remove_hwmon_sysfs+0x175/0x1d0
thermal_zone_device_unregister+0x188/0x1e0
iwl_mvm_thermal_exit+0xe7/0x100 [iwlmvm]
iwl_op_mode_mvm_stop+0x27/0x180 [iwlmvm]
_iwl_op_mode_stop.isra.3+0x2b/0x50 [iwlwifi]
iwl_opmode_deregister+0x90/0xa0 [iwlwifi]
__exit_compat+0x10/0x2c7 [iwlmvm]
__x64_sys_delete_module+0x13f/0x270
do_syscall_64+0x5a/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The current budget of 2000mA is preventing us from reaching maximum
throughput. According to our system engineers, we can increase the
maximum budget to 2400mA to solve this problem.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Without CONFIG_THERMAL, the driver fails to link as it calls
iwl_mvm_send_temp_report_ths_cmd() unconditionally. Fix this
by making that function available, but do almost nothing but
send the empty firmware command to enable CT-kill reporting.
While at it, also fix that function itself to not error out
when the thermal zone hasn't been initialized, but instead
just send the empty firmware command in this case as well.
Fixes: 242d9c8b9a93 ("iwlwifi: mvm: use FW thermal monitoring regardless of CONFIG_THERMAL")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As part of the d0i3 removal.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It seems that libsensors treats -EIO as a special non-recoverable
failure when it tries to read the temperature while the firmware is
not running. To solve that, change the error code to a milder
-ENODATA.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196941
Fixes: c221daf219b1 ("iwlwifi: mvm: add registration to thermal zone")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We always must set the status to what we consider success before
calling iwl_mvm_send_cmd_status() (also iwl_mvm_send_cmd_pdu_status()
which calls it). Fix a few places where initialization is missing.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
CT-kill is a thermal-based "RF-kill", which disables the NIC
completely if the temperature gets too high, in order to avoid damage.
Add a debugfs entry to simulate high temperatures, in order to test
CT-kill flows in the driver without having to physically heat the
device up.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi driver patches 4.13
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().
|
|
This will help refactor this later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case an assert happens on init flow, the current
driver powers down the NIC, except if iwlmvm modparam
init_dbg=1, and only on very specific flows.
Extend this capability to cover most failure cases
by keeping track of what init configurations have been
completed. This way, we can allow NOT powering down
the NIC, while making sure that when the driver is
removed we don't try to free resources that haven't
been allocated. (This can result in a kernel panic.)
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.
Fixes: 5c89e7bc557e ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A recent firmware change seems to have enabled thermal zones on the
iwlwifi driver. Unfortunately, my device fails when registering the
thermal zone. This doesn't stop the driver from attempting to unregister
the thermal zone at unload time, triggering a NULL pointer deference in
strlen() off the thermal_zone_device_unregister() path.
Don't unregister if name is NULL, for that case we failed registering.
Do the same for the cooling zone.
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
FW versions older than -17 for 3160 and 7260 and older than -22 for
newer NICs are not supported anymore. Don't load these versions
and remove code that handles them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Getting the mvm station out of station id requires dereferencing
the station id to get ieee80211_sta, then checking for pointer
validity and only then extract mvm station out.
Given that there are helpers to do it - use them instead of
duplicating the code whenever we need only mvm station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We were not allowing the thermal state to be set when we were in D0i3
mode. It was not very clearly specified how it should work, but now a
decision was made to allow the state to be set in D0i3 (which will
cause a brief wake up). Remove the check in the set_cur_state
operation.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The driver can read the current state during D0I3,
therefore there is no reason not to do it.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Use RX_HANDLER_ASYNC_UNLOCKED instead of unlock and re-lock
the mutex independently.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
iwl_mvm_tcool_get_cur_state is the function that returns the
cooling state index to the sysfs handler. This function returns
mvm->cooling_dev.cur_state but that variable was set to the
budget and not the cooling state index. Fix that.
Add a missing blank line while at it.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add debugfs entries to get the ctdp budget average
and to stop ctdp.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
