| Age | Commit message (Collapse) | Author |
|---|
|
Can't rely that band 2.4 is always supported by the NIC and use the
first channel in this band for the phy ctxt.
Instead, look for the first channel in the first band that is supported
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
TX power limits as defined in the OTP assume the worst case scenario
in terms of the platform's atenna gain, but most platforms are below
that value so they can use more TX power without passing the regulatory
limit. If the platform indicates in the BIOS that it indeed has lower
gain, and the geographic location allows it, higher TX power can be
used. The driver reads the PPAG (Per-Platform Antenna Gain) data from
BIOS (if it exists), validates it and sends the appropriate command to
the FW. This flow happens once at FW init, in case of suspend/resume
there is no need to read again from BIOS as we save those values during
init, so just send the PPAG command again to FW.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The check is not necessary anymore, because now the struct is not
allocated separately, but is part of the mvmsta struct. Remove the
check, since it's dead code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Any firmware that supports the new channel switch flow is
able to close / re-open the queues when needed. It takes
into account the channel switch mode etc...
Don't open / close the queues or enable / disable beacon
abort before and after the channel switch in case the
firmware is able to do this by itself.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Function iwl_mvm_scan_set_legacy_probe_req() second argument
size is too large to be passed by value.
Fix it to be passed by reference.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It doesn't make sense to use the FW thermal monitoring only if we
have CONFIG_THERMAL, because then we use the default thresholds
etc. which may be different from what the firmware implements, as
we don't maintain them in the driver now. Only the CTDP code needs
to actually be under CONFIG_THERMAL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It's hard to follow the numbers so rename it with enum
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Scan API was changed to support 6Ghz channels as well.
Support the new version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
New FW versions introduces LTR feature enablement by default.
For such FW versions, driver (mvm/xvt) should not send
host command to enable LTR feature, also it should be possible to
override LTR configuration through the debugfs.
1. Send LTR feature enablement command only for FW versions
which does not advertises SET_LTR_GEN2 capability.
2. Implement ltr_config file in debugfs for LTR configuration override.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
|
|
We're now left with a status bit that is never set and a few
other leftovers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Also change the signature of the power functions that won't
receive d0i3=true anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This variable read, but never set. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Now that d0i3 is dead, this function can't be called from d0i3
flows. Change its signature and make it static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is not needed anymore
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As part of the d0i3 removal.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For runtime PM to work with d0i3 code, a lot of integration work needs
to be done with the platform (e.g. the out-of-band wake up interrupt)
and we currently don't have any platforms where this integration
happened. So, this code has been pretty much stale for a while and
when someone enables it, it just breaks things.
Therefore, to simplify the code base and make sure no one enables this
by mistake, we will remove the whole code.
This is only the very start, much more work is needed.
Remove the places where we check iwl_mvm_is_d0i3_supported
but leave all the refs, those will be removed in a different
patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When printing a TX, add to the print the length of the frame.
That will help with BSEP (buffer status report poll) tests.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Use the actual length of channels array and not the max capable length.
Signed-off-by: Beker Ayala <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
add support to print ldbg command in mvm and xvt mode
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support the new DBGC_SUSPEND_RESUME command to change the recording state.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
These static functions are only used after their definition,
so we don't need the forward declarations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case that there are OBSS that do not know how to properly
interpret 26-tone RU OFDMA transmissions, instruct the FW not
to use such transmissions.
The check is currently only performed upon association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If mvm->fwrt.cur_fw_img != IWL_UCODE_INIT, then
rfkill_safe_init_done must be true since
rfkill_safe_init_done is set to true before we start to load
the runtime image.
Remove the redundant condition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The newer targets don't support the DQA enablement command
and will return error status, while older targets need it.
The feature is defined by the corresponding TLV.
Send the command only if the TLV is enabled.
Signed-off-by: Ilia Lin <ilia.lin@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Minor conflict in r8169, bug fix had two versions in net
and net-next, take the net-next hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC context configuration always allowed multicast data frames
to pass to the driver for all MAC context types, and in the
case of station MAC context both when associated and when not
associated.
One of the outcomes of this configuration is having the FW forward
encrypted multicast frames to the driver with Rx status indicating
that the frame was not decrypted (as expected, since no keys were
configured yet) which in turn results with unnecessary error
messages.
Change this behavior to allow multicast data frames only when they
are actually expected, e.g., station MAC context is associated etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Just minor overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accessing the hdr of an skb that was consumed already isn't
a good idea.
First ask if the skb is a QoS packet, then keep that data
on stack, and then consume the skb.
This was spotted by KASAN.
Cc: stable@vger.kernel.org
Fixes: 08f7d8b69aaf ("iwlwifi: mvm: bring back mvm GSO code")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The index for the elements of the ACPI object we dereference
was static. This means that if we called the function twice
we wouldn't start from 3 again, but rather from the latest
index we reached in the previous call.
This was dutifully reported by KASAN.
Fix this.
Cc: stable@vger.kernel.org
Fixes: 6996490501ed ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We erroneously added a check for FW API version 41 before sending
GEO_TX_POWER_LIMIT, but this was already implemented in version 38.
Additionally, it was cherry-picked to older versions, namely 17, 26
and 29, so check for those as well.
Cc: stable@vger.kernel.org
Fixes: eca1e56ceedd ("iwlwifi: mvm: don't send GEO_TX_POWER_LIMIT to old firmwares")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
lq_info is an arary of size 2, active_tbl index is u8.
When accessing lq_info[1 - active_tbl], theoretically it's possible
that the access will be made to a negative index value.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
An earlier patch made sure that the queues are not lagging
too far behind. This means that iwl_mvm_release_frames
should not be called with a head_sn too far behind NSSN.
Don't take the risk to change completely the entry
condition to iwl_mvm_release_frames, but don't update
the head_sn is the NSSN is more than 2048 packets ahead
of us. Since this just cannot be right. This means that
the scenario described here happened. We are queue 0.
Q:0 Q:1
head_sn: 0 -> 2047
head_sn: 2048
Lots of packets arrive:
head_sn: 2047 -> 2150
send NSSN_SYNC notification
Handle notification
from the firmware and
do NOT move the head_sn
back to 2048
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The solution with the worker still had a bug, as in order
to get sta, rcu_read_lock should be used and thus no mutex
can be used inside iwl_mvm_rs_rate_init.
Also, spin_lock is a simpler solution, no need to spawn a
dedicated worker.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The only place where the command was sent as SYNC is during
init and this is not really critical. This change is required
for replacing RS mutex with a spinlock (in the subsequent patch),
since SYNC comamnd requres sleeping and thus the flow cannot
be done when holding a spinlock.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The comparison of the u32 variable wgds_tbl_idx with less than zero is
always going to be false because it is unsigned. Fix this by making
wgds_tbl_idx a plain signed int.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 4fd445a2c855 ("iwlwifi: mvm: Add log information about SAR status")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This code clearly never could have worked, since it locks
while already locked. Add an unlocked __iwl_mvm_mac_set_key()
variant that doesn't do locking to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
iwl_mvm_rs_tx_status can be called from two places in the code, but the
mutex is taken only on one of the calls. Split it into a wrapper taking
locks and an internal __iwl_mvm_rs_tx_status function.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to support MSI-X efficiently, we want to avoid
communication across Rx queues. Each Rx queue should have
all the data it needs to process a packet.
The reordering buffer is a challenge in the MSI-X world
since we can have a single BA session whose packets are
directed to different queues. This is why each queue has
its own reordering buffer. The hardware is able to hint
the driver whether we have a hole or not, which allows
the driver to know whether it can release a packet or not.
This indication is called NSSN. Roughly, if the packet's
SN is lower than the NSSN, we can release the packet to
the stack. The NSSN is the SN of the newest packet received
without any holes + 1.
This is working as long as we don't have packets that we
release because of a timeout. When that happens, we could
have taken the decision to release a packet after we have
been waiting for its predecessor for too long. If this
predecessor comes later, we have to drop it because we
can't release packets out of order. In that case, the
hardware will give us an indication that we can we release
the packet (SN < NSSN), but the packet still needs to be
dropped.
This is why we sometimes need to ignore the NSSN and we
track the head_sn in software.
Here is a specific example of this:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480
6) 481 arrives its NSSN is 484.
We need to drop 481 even if 481 < 484. This is why we'll
update the head_sn to 484 at step 2. The flow now is:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481 / head_sn is 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480 but head_sn is 484.
6) 481 arrives its NSSN is 484, but head_sn is 484 and we drop it.
This code introduces another problem in case all the traffic
goes well (no hole, no timeout):
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 4095 (head_sn = 0)
Rx queue 2: 0 -> 480 (head_sn = 481)
Rx queue 1: 481 but head_sn = 484 and we drop it.
At this point, the SN of queue 1 is far behind: more than
4040 packets behind. Queue 1 will consider 481 "old"
because 481 is in [501-64:501] whereas it is a very new
packet.
In order to fix that, send an Rx notification from time to
time (twice across the full set of 4096 packets) to make
sure no Rx queue is lagging too far behind.
What will happen then is:
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 2047 (head_sn = 2048)
Rx queue 1: Sync nofication (head_sn = 2048)
Rx queue 2: 2048 -> 4095 (head_sn = 0)
Rx queue 1: Sync notification (head_sn = 0)
Rx queue 2: 1 -> 481 (head_sn = 482)
Rx queue 1: 481 and head_sn = 0.
In queue 1's data, head_sn is now 0, the packet coming in
is 481, it'll understand that the new packet is new and it
won't be dropped.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of allocating memory for which we have an upper
limit, use a small buffer on stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We will soon be using a new notification that will be
initiated by the driver, sent to the firmware and sent
back to all the RSS queues by the firmware. This new
notification will be useful to synchronize the NSSN across
all the queues.
For now, don't send the notification, just add the code to
handle it. Later patch will add the code to actually send
it.
While at it, validate the baid coming from the firmware to
avoid accessing an array with a bad index in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We will need a new type of synchronization message going
through all the RSS queues. Prepare the ground for this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Firmware versions before 41 don't support the GEO_TX_POWER_LIMIT
command, and sending it to the firmware will cause a firmware crash.
We allow this via debugfs, so we need to return an error value in case
it's not supported.
This had already been fixed during init, when we send the command if
the ACPI WGDS table is present. Fix it also for the other,
userspace-triggered case.
Cc: stable@vger.kernel.org
Fixes: 7fe90e0e3d60 ("iwlwifi: mvm: refactor geo init")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Rate perform uses the lq_sta table to calculate the next rate to scale
while rate init resets the same table,
Rate perform is done in soft irq context in parallel to rate init
that can be called in case we are doing changes like AP changes BW
or moving state for auth to assoc.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On older NICs, we occasionally see issues with A-MSDU support,
where the commands in the FIFO get confused and then we see an
assert EDC because the next command in the FIFO isn't TX.
We've tried to isolate this issue and understand where it comes
from, but haven't found any errors in building the A-MSDU in
software.
At least for now, disable A-MSDU support on older hardware so
that users can use it again without fearing the assert.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=203315.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The .remove_sta_debugfs callback was not doing anything in this driver,
so remove it as it is not needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190612142658.12792-4-gregkh@linuxfoundation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
