| Age | Commit message (Collapse) | Author |
|---|
|
In the regular flow, when we receive an assert, ieee80211_reconfig is
called which reconfig the driver using iwl_mvm_mac_start.
iwl_mvm_mac_start is clearing the restart bit and does dump collection.
Prior to setting the device up, ieee80211_reconfig does not call
iwl_mvm_mac_start since there is nothing to reconfig and we miss the
dump collection of the assert.
solve it by checking the restart bit before we stop the device
and trigger a dump collection in case it is set.
note that we don't need to do it in the fmac case since in fmac
assert flow in iwl_fmac_nic_error we call iwl_fw_dbg_collect_desc
so we can be sure that there will a dump collection in
iwl_fmac_stop_device.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In order to make more sense out of the captured radiotap data e.g.
when the configured AID changes, add the currently configured AID
to the radiotap data as a vendor extension field.
This is made race-free by updating the included value from inside
the RX path (using a notification wait) for the command response
from the firmware, which thus means it's serialized with frame RX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The reorder buffer is bypassed because the firmware won't have
any BA sessions, document this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We introduce a new state for latency, force mode, in force mode
you can enable always to be in low latency or always to be in non
low latency.
This is required for test mode in max TpT test.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We maintain a timer for each Tx queue to detect stalls and
be able to recover / debug.
When we work in AP mode, we can freeze the Tx queue timer if
a station goes to sleep, because we don't want to warn about
stalls that are caused by faulty clients that don't wake up
on time.
This mechanism was applied to the queues of the clients, but
the management queue was omitted. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Change iwl_fw_channel_info structure so it can have channel number
greater than 255. This is needed for 6 GHz channel numbers.
Change all relevant structs and member accesses accordingly.
The new API is indicated by a TLV capability bit.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Implement CSI (channel estimation matrix) reporting in the mvm
driver, if the firmware has the capability.
Currently only a debugfs API is provided as the API is still
under discussion.
For now, RX aggregation must be disabled to use this feature
on data frames as we haven't found a good way to attach the
data to A-MPDUs, given complexities with multi-queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add the location/time-of-flight/FTM APIs that we'll use in
follow-up patches to implement FTM responder and initiator.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some buggy APs stop sending beacons, but continue to ack our null data
packets or even run some traffic. It's better not to stick connected to
such an AP forever, so disconnect after some larger beacon loss
threshold is crossed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is an ancient (~2015) implementation that no longer matches
the firmware in any way, and most likely never worked. Remove all
of it so it can be reintroduced properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
TX path lock was introduced in order to prevent out of order
invocations of TX.
This can happen in the following flow:
TX path invoked from net dev
Packet dequeued
TX path invoked from RX path
Packet dequeued
Packet TXed
Packet TXed
However, we don't really need a lock. If TX path is already
invoked from some location, other paths can simply abort their
execution, instead of waiting to the first path to finish, and
then discover queue is (likely) empty or stopped.
Replace the lock with an atomic variable to track TX ownership.
This simplifies the locking dependencies between RX and TX paths,
and should improve performance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The current code assigns the reference, and then goes to increment
it if the toggle bit has changed. That way, we get
Toggle 0 0 0 0 1 1 1 1
ID 1 1 1 1 1 2 2 2
Fix that by assigning the post-toggle ID to get
Toggle 0 0 0 0 1 1 1 1
ID 1 1 1 1 2 2 2 2
Reported-by: Danny Alexander <danny.alexander@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: fbe4112791b8 ("iwlwifi: mvm: update mpdu metadata API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently whenever we get firmware notification with mac id,
we iterate over all the interfaces to find the ID. This is a
bit cumbersome. Instead, adding an array of RCU pointers, like
we have for station IDs. This is not expensive space wise
since we have only up to 4 active MACs, and not complicated
code wise, since we have a clear point to init and de-init it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If WEP is used, no one removes the STA key upon STA
removal, leading to a situation where after 16
connect/disconnects - the AP could no longer decrypt
incoming data frames since iwl_mvm_set_fw_key_idx()
called from iwl_mvm_set_sta_key() during association
returns STA_KEY_IDX_INVALID, thus not setting the key
for that connecting STA.
Fix this by removing the key in the driver when the
STA is removed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The function we pass to the wait alive notification procedure may may
not even get called if the timeout occurs before the function is
called. To prevent accessing unitialized data in alive_data, pre-set
it to zero in the declaration. Found by static analyzers.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
These inlines just check the module parameters, so they don't
need a configuration parameter and can move to a better place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Sometimes we want to debug issues related to the regulatory blob in
the NVM. To make that easier, add a debugfs entry to export it
together with the other nvm blobs we export.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Clean up the LDBG config command to not be called "continuous
recording", and while at it actually remove the continuous
recording implementation completely since it was only used for
store & forward architectures.
This also fixes a bug at least in iwl_fw_dbg_buffer_allocation()
because what's now "__le32 type" (matching the firmware) used to
be "__le16 enable_recording", so the buffer allocation config
sub-struct would erroneously have started at the wrong offset.
In the other cases this didn't actually lead to a bug as other
bytes in pad[] were all zeroes, so accessing the 16-bit value as
a 32-bit value wouldn't make a difference (in little endian.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Due to a general shortage of RX API bits, the firmware is going
to reuse this bit on non-CCK frames to mean something else. Use
it only on CCK frames to prepare for that change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
With just %16, it means 16 characters padding, but we really
don't want to print "0x 1F4547B", but instead want to
have this filled with zeroes, so we need the 0.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Take the NSS value from 'rx_vec' rather than from 'rate_n_flags'.
The rate_n_flags has only 2 bits for the NSS giving a max of 4SS
(0 = 1SS etc.). Since there may be up to 8SS use the rx_vec which
has 3 bits for the NSS.
While at it, fix the rx_vec array to length of 2.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When setting the EOF bit in Rx flags (propagated
to radiotap) do not depend it on the PPDU type (SU/MU/TB)
since it doesn't.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The value in txq_id can be out of array scope,
validate it before accessing the array.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The driver assumes certain sizes and lengths aren't crossed in some
places. Make sure this indeed happens.
Found by Klocwork.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There is no point in having num_active_macs signed
since it should never be negative. Set it to be an
unsigned variable to ensure this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As this is not needed and might cause interoperability issues
during pairing with devices that would not reply to RTS frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When a frame is transmitted without a station, need to set the rate
and flags in the Tx command, as the FW does not have any information as
to what rate and flags should be used for this frame.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When a time event for a P2P Device interface is done, it is possible
that there is still a frame pending for transmission that should be
flushed.
Set the IWL_MVM_STATUS_NEED_FLUSH_P2P to indicate to the ROC worker
that P2P Device station queue need also to be flushed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We have a slightly better TCP performance with GSO.
Add it back, it can co-exist with the code that builds
AMSDUs in mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We erroneously had some values for NGI in the table we give as an
example in rs_fill_rates_for_column(), when they should be SGI.
Change them so that they match what we say.
Reported-by: Rémy Grünblatt <remy@grunblatt.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support getting mac80211 building AMSDUs for us. Remove GSO
support from mvm - we don't need it anymore.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move to use the new mac80211 TXQs implementation. This has
quite a few benefits for us. We can get rid of the awkward
mapping of DQA to mac80211 queues. We can stop buffering
traffic while waiting for the queue to be allocated. We can
also use mac80211 AMSDUs instead of building it ourselves.
The usage is pretty simple:
Each ieee80211_txq contains iwl_mvm_txq. There is such a
queue for each TID, and one for management frames. We keep
having static AP queues for probes and non-bufferable MMPDUs,
along with broadcast and multicast queues. Those are being
used from the "old" TX invocation path - iwl_mvm_mac_tx.
When there is a new frame in a TXQ, iwl_mvm_mac_wake_tx is
being called, and either invokes the TX path, or allocates
the queue if it does not exist.
Most of the TX path is left untouched, although we can consider
cleaning it up some more, for example get rid of the duplication
of txq_id in both iwl_mvm_txq and iwl_mvm_dqa_txq_info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
On any failure, including if we crash the firmware or get garbage
data, we currently ignore this and pretend the OTP was empty.
Clearly, this isn't typically the case.
In cases other than the firmware saying it can't read the requested
section, or the section having ended, make the access actually fail
and trickle the error up through the layers to fail init.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The new (CDB) statistics API is used by non-CDB devices
as well. Look at the right TLV flag to know which version
of the statistics notification to use.
To avoid confusion, remove the _cdb suffix from the
structure name.
While at it, remove a structure that was never used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 678d9b6dddea ("iwlwifi: mvm: update rx statistics cmd api")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When configuring TLC DCM flag:
1. check the peer's RX DCM capabilities (since we TX)
2. do not set DCM_NSS_2 since we do not support it
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Fixes: 423584dd8060 ("iwlwifi: rs-fw: support dcm")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Mac80211 will check both the HE Capability IE and the
Extended Capability IE, so set the TWT support bit when
mac80211 tells us to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We want to advertise support for TWT in the Extended
Capability IE. Since we don't want to set the bits for all
the interface types, define an interface specific
configuration.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add to the dump the number of lmacs, the error id of the umac
and the error id of lmac1, if supported.
In case the reason for the dump trigger is not an assert
the error id is zero.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Trivial fix to spelling mistake in debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add the rt status of the last assert or 0 if the dump collection was
not initiated by an assert. Add the number of rx and tx fifos in use.
These fields are added to dump info lst file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Sometimes, due to SCD bug, we need to start the queue with an
higher SSN. The queue allocation function currently increments
the SSN in the packet itself, but it is pointless, since this
value is overridden later by iwl_mvm_tx_mpdu with the value
from mvmsta->tid_data[tid].seq_number. Updating tid data is
sufficient.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is no need to lock mvm station for transport reclaim.
Move the locking down, after the reclaim.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Handle RX no data notification, which is used for advertising NDP to
radiotap.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The FW expects to get the ppe value for each NSS-BW pair in the same
format as in the he phy capabilities IE, which means that a value of 0
implies ppe should be used for BPSK (mcs 0). If there are no PPE
thresholds in the IE, or if for some NSS-RU pair there's no threshold
set for it (this could happen because it's a variable-sized field), it
means no PPE should not be used for that pair, so the value sent to FW
should be 7 which corresponds to "none".
Fixes: 514c30696fbc ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make the coupling of station id and queue id clear. Group code
together. Remove outdated comment. Never use an undefined hw
queue as given from mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Assigning mvmsta to be NULL when we are about to exit the
function is pointless. Remove it. Move the variable declaration
to the scope it is used.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
the AP station was supposed to be used for multicast frames
instead of the auxiliary station to avoid frames possibly
sent to an absent P2P GO. However, when moving to DQA mode,
this was broken as no valid queue was assigned. This is fixed
by a recent patch that directs all non-offchannel traffic to
ap station earlier in the TX path. However, the broken, and
now dead code, remained. Remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
