| Age | Commit message (Collapse) | Author |
|---|
|
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
Acked-by: Michael Büsch <m@bues.ch>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/oe-kbuild-all/202305160749.ay1HAoyP-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516183442.536589-1-arnd@kernel.org
|
|
The Allwinner sunxi-mmc controller cannot handle word (16 bit)
transfers. So and sdio_{read,write}w fails with messages like the
following example using an RTL8822BS (but the same problems were also
observed with RTL8822CS and RTL8723DS chips):
rtw_8822bs mmc1:0001:1: Firmware version 27.2.0, H2C version 13
sunxi-mmc 4021000.mmc: unaligned scatterlist: os f80 length 2
sunxi-mmc 4021000.mmc: map DMA failed
rtw_8822bs mmc1:0001:1: sdio read16 failed (0x10230): -22
Use two consecutive single byte accesses for word operations instead. It
turns out that upon closer inspection this is also what the vendor
driver does, even though it does have support for sdio_{read,write}w. So
we can conclude that the rtw88 chips do support word access but only on
SDIO controllers that also support it. Since there's no way to detect if
the controller supports word access or not the rtw88 sdio driver
switches to the easiest approach: avoiding word access.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Closes: https://lore.kernel.org/linux-wireless/527585e5-9cdd-66ed-c3af-6da162f4b720@lwfinger.net/
Reported-by: Rudi Heitbaum <rudi@heitbaum.com>
Link: https://github.com/LibreELEC/LibreELEC.tv/pull/7837#issue-1708469467
Fixes: 65371a3f14e7 ("wifi: rtw88: sdio: Add HCI implementation for SDIO based chipsets")
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230515195043.572375-1-martin.blumenstingl@googlemail.com
|
|
When parse_pmsr_capa failed in hwsim_new_radio_nl, the memory resources
applied for by pmsr_capa are not released. Add release processing to the
incorrect path.
Fixes: 92d13386ec55 ("mac80211_hwsim: add PMSR capability support")
Reported-by: syzbot+904ce6fbb38532d9795c@syzkaller.appspotmail.com
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230515092227.2691437-1-shaozhengchao@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The rs_drv_get_rate flow reads the lq_sta to return the optimal rate
for tx frames. This read flow is not protected thereby leaving
a small window, a few instructions wide, open to contention by an
asynchronous rate update. Indeed this race condition was hit and the
update occurred in the middle of the read.
Fix this by locking the lq_sta struct during read.
Signed-off-by: Ariel Malamud <ariel.malamud@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.b52c9ed5c379.I15290b78e0d966c1b68278263776ca9de841d5fe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This bitmap equals to zero when in a non-MLO mode, and then we won't
be iterating on any link. Use for_each_sta_active_link() instead, as
it handles also the case of non-MLO mode.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.f32a8c08730a.Ib02248cd0b7f2bc885f91005c3c110dd027f9dcd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the firmware sends us a corrupted MCC response with
n_channels much larger than the command response can be,
we might copy far too much (uninitialized) memory and
even crash if the n_channels is large enough to make it
run out of the one page allocated for the FW response.
Fix that by checking the lengths. Doing a < comparison
would be sufficient, but the firmware should be doing
it correctly, so check more strictly.
Fixes: dcaf9f5ecb6f ("iwlwifi: mvm: add MCC update FW API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.d7b233139eb4.I51fd319df8e9d41881fc8450e83d78049518a79a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix a spelling mistake.
Fixes: 2856f623ce48 ("iwlwifi: mvm: Add list of OEMs allowed to use TAS")
Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.4090de6d1878.If9391ef6da78f1b2cc5eb6cb8f6965816bb7a7f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix a spelling mistake.
Fixes: e8e10a37c51c ("iwlwifi: acpi: move ppag code from mvm to fw/acpi")
Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.fdd07f36a8bf.I223e5fb16ab5c95d504c3fdaffd0bd70affad1c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In iwl_mvm_mld_update_sta(), if the flow doesn't enter
for_each_sta_active_link(), the default value is returned.
Set this default to -EINVAL instead of 0 to better reflect
this.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.98b7e3aacf0b.I2fc274dd7e374ef7fac8e26d71c9cd73323da665@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
RCU protected fw_id_to_mac_id can be initialized with either
an error code or NULL. Thus, after dereferencing need to check
the value with IS_ERR_OR_NULL() and not only that it is not NULL.
Fix it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.ec5f2880e81c.Ifa8c0f451df2835bde800f5c3670cc46238a3bd8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The DBGI dump is (unsurprisingly) of type DBGI, not SRAM.
This leads to bad register accesses because the union is
built differently, there's no allocation ID, and thus the
allocation ID ends up being 0x8000.
Note that this was already wrong for DRAM vs. SMEM since
they use different parts of the union, but the allocation
ID is at the same place, so it worked.
Fix all of this but set the allocation ID in a way that
the offset calculation ends up without any offset.
Fixes: 34bc27783a31 ("iwlwifi: yoyo: fix DBGI_SRAM ini dump header.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.19a302ae4c65.I12272599f7c1930666157b9d5e7f81fe9ec4c421@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The concurrent link checks need to correctly differentiate
between AP and non-AP, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.992b2f981ef6.I7d386c19354e9be39c4822f436dd22c93422b660@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Lockdep points out that we can deadlock here by calling
cancel_delayed_work_sync() because that might be already
running and gotten interrupted by the NAPI soft-IRQ.
Even just calling something that can sleep is wrong in
this context though.
Luckily, it doesn't even really matter since the things
we need to do are idempotent, so just drop the _sync().
Fixes: e5d153ec54f0 ("iwlwifi: mvm: fix CSA AP side")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.b1813c823b4d.I9d20cc06d24fa40b6774d3dd95ea5e2bf8dd015b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We don't need to (and shouldn't) initialize the spinlock
during HW restart that was already initialized, so move
that into the correct if block. Since then we have two
consecutive if statements with the same (though inverted)
condition, unify those as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.221c22cfdf4e.I2e30113ef4bd8cb5bd9e1a69e52a95671914961c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are some assertions in the STA removal code that can
fail, and in that case we may leak memory since we skip
the freeing.
Fix this by freeing the dup_data earlier in the function,
we already have a check for when we free the station, and
this we don't need to do it with and without MLD API, so
it's a win all around.
Fixes: a571f5f635ef ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.173938681d72.Iff4b55fc52943825d6e3e28d78a24b155ea5cd22@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This feature depends on a platform bugfix. Until we have a
mechanism that can verify a platform has the required bugfix,
disable RFI.
Fixes: ef3ed33dfc8f ("wifi: iwlwifi: bump FW API to 77 for AX devices")
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Link: https://lore.kernel.org/linux-wireless/CAAJw_ZvZdFpw9W2Hisc9c2BAFbYAnQuaFFaFG6N7qPUP2fOL_w@mail.gmail.com/
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Link: https://lore.kernel.org/all/20230427020512.1221062-1-luyun_611@163.com
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512012055.2990472-1-luyun_611@163.com
|
|
The probe() id argument may be NULL in 2 scenarios:
1. brcmf_pcie_pm_leave_D3() calling brcmf_pcie_probe() to reprobe
the device.
2. If a user tries to manually bind the driver from sysfs then the sdio /
pcie / usb probe() function gets called with NULL as id argument.
1. Is being hit by users causing the following oops on resume and causing
wifi to stop working:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
Hardware name: Dell Inc. XPS 13 9350/0PWNCR, BIDS 1.13.0 02/10/2020
Workgueue: events_unbound async_run_entry_fn
RIP: 0010:brcmf_pcie_probe+Ox16b/0x7a0 [brcmfmac]
<snip>
Call Trace:
<TASK>
brcmf_pcie_pm_leave_D3+0xc5/8x1a0 [brcmfmac be3b4cefca451e190fa35be8f00db1bbec293887]
? pci_pm_resume+0x5b/0xf0
? pci_legacy_resume+0x80/0x80
dpm_run_callback+0x47/0x150
device_resume+0xa2/0x1f0
async_resume+0x1d/0x30
<snip>
Fix this by checking for id being NULL.
In the PCI and USB cases try a manual lookup of the id so that manually
binding the driver through sysfs and more importantly brcmf_pcie_probe()
on resume will work.
For the SDIO case there is no helper to do a manual sdio_device_id lookup,
so just directly error out on a NULL id there.
Fixes: da6d9c8ecd00 ("wifi: brcmfmac: add firmware vendor info in driver info")
Reported-by: Felix <nimrod4garoa@gmail.com>
Link: https://lore.kernel.org/regressions/4ef3f252ff530cbfa336f5a0d80710020fc5cb1e.camel@gmail.com/
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230510141856.46532-1-hdegoede@redhat.com
|
|
qsel_to_ep[] can be assigned negative value, so change type from 'u8' to
'int'. Otherwise, Smatch static checker warns:
drivers/net/wireless/realtek/rtw88/usb.c:219 rtw_usb_parse() warn:
assigning (-22) to unsigned variable 'rtwusb->qsel_to_ep[8]'
Cc: stable@vger.kernel.org
Fixes: a6f187f92bcc ("wifi: rtw88: usb: fix priority queue to endpoint mapping")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/linux-wireless/c3f70197-829d-48ed-ae15-66a9de80fa90@kili.mountain/
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508085539.46795-1-pkshih@realtek.com
|
|
The ieee80211_ops::sta_rc_update must be atomic, because
ieee80211_chan_bw_change() holds rcu_read lock while calling
drv_sta_rc_update(), so create a work to do original things.
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 4621 at kernel/rcu/tree_plugin.h:318
rcu_note_context_switch+0x571/0x5d0
CPU: 0 PID: 4621 Comm: kworker/u16:2 Tainted: G W OE
Workqueue: phy3 ieee80211_chswitch_work [mac80211]
RIP: 0010:rcu_note_context_switch+0x571/0x5d0
Call Trace:
<TASK>
__schedule+0xb0/0x1460
? __mod_timer+0x116/0x360
schedule+0x5a/0xc0
schedule_timeout+0x87/0x150
? trace_raw_output_tick_stop+0x60/0x60
wait_for_completion_timeout+0x7b/0x140
usb_start_wait_urb+0x82/0x160 [usbcore
usb_control_msg+0xe3/0x140 [usbcore
rtw_usb_read+0x88/0xe0 [rtw_usb
rtw_usb_read8+0xf/0x10 [rtw_usb
rtw_fw_send_h2c_command+0xa0/0x170 [rtw_core
rtw_fw_send_ra_info+0xc9/0xf0 [rtw_core
drv_sta_rc_update+0x7c/0x160 [mac80211
ieee80211_chan_bw_change+0xfb/0x110 [mac80211
ieee80211_change_chanctx+0x38/0x130 [mac80211
ieee80211_vif_use_reserved_switch+0x34e/0x900 [mac80211
ieee80211_link_use_reserved_context+0x88/0xe0 [mac80211
ieee80211_chswitch_work+0x95/0x170 [mac80211
process_one_work+0x201/0x410
worker_thread+0x4a/0x3b0
? process_one_work+0x410/0x410
kthread+0xe1/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Cc: stable@vger.kernel.org
Fixes: c1edc86472fc ("rtw88: add ieee80211:sta_rc_update ops")
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/linux-wireless/f1e31e8e-f84e-3791-50fb-663a83c5c6e9@lwfinger.net/T/#t
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508085429.46653-1-pkshih@realtek.com
|
|
Though SER can recover this case, traffic can get stuck for a while. Fix it
by adjusting page quota to avoid hardware access null page of CMAC/DMAC.
Fixes: a1cb097168fa ("wifi: rtw89: 8852b: configure DLE mem")
Fixes: 3e870b481733 ("wifi: rtw89: 8852b: add HFC quota arrays")
Cc: stable@vger.kernel.org
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://github.com/lwfinger/rtw89/issues/226#issuecomment-1520776761
Link: https://github.com/lwfinger/rtw89/issues/240
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230426034737.24870-1-pkshih@realtek.com
|
|
The stats->tx_bytes shall subtract retry byte from tx byte.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/b3cd45596943cf5a06b2e08e2fe732ab0b51311b.1682285873.git.ryder.lee@mediatek.com
|
|
To avoid sparse warning:
sparse: warning: invalid assignment: |=
sparse: left side has type restricted __le32
sparse: right side has type unsigned lon
Fixes: 15ee62e73705 ("wifi: mt76: mt7996: enable BSS_CHANGED_BASIC_RATES support")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/16fa938373e3b145cb07a2c98d2428fea2abadba.1682285873.git.ryder.lee@mediatek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly standard release for SPI with the exception of a change to
the API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily
for a while.
There's also a new API to allow us to support TPM chips on half duplex
controllers.
Summary:
- Refactoring in preparation for supporting multiple chip selects for
a single device, needed by some flash devices, which required a
change in the SPI device API visible throughout the tree
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI
- Optimisation for large transfers on fsl-cpm devices
- Cleanups around device property use which fix some sisues with
fwnode
- Use of both void remove() and devm_platform_.*ioremap_resource()
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI"
* tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (185 commits)
spi: bcm63xx: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: tegra210-quad: Enable TPM wait polling
spi: Add TPM HW flow flag
spi: bcm63xx: remove PM_SLEEP based conditional compilation
spi: cadence-quadspi: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: spi-cadence: Add support for Slave mode
spi: spi-cadence: Switch to spi_controller structure
spi: cadence-quadspi: fix suspend-resume implementations
spi: dw: Add support for AMD Pensando Elba SoC
spi: dw: Add AMD Pensando Elba SoC SPI Controller
spi: cadence-quadspi: Disable the SPI before reconfiguring
spi: cadence-quadspi: Update the read timeout based on the length
spi: spi-loopback-test: Add module param for iteration length
spi: add support for Amlogic A1 SPI Flash Controller
dt-bindings: spi: add Amlogic A1 SPI controller
spi: fsl-spi: No need to check transfer length versus word size
spi: fsl-spi: Change mspi_apply_cpu_mode_quirks() to void
spi: fsl-cpm: Use 16 bit mode for large transfers with even size
spi: fsl-spi: Re-organise transfer bits_per_word adaptation
spi: fsl-spi: Fix CPM/QE mode Litte Endian
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Introduce a config option to tweak MAX_SKB_FRAGS. Increasing the
default value allows for better BIG TCP performances
- Reduce compound page head access for zero-copy data transfers
- RPS/RFS improvements, avoiding unneeded NET_RX_SOFTIRQ when
possible
- Threaded NAPI improvements, adding defer skb free support and
unneeded softirq avoidance
- Address dst_entry reference count scalability issues, via false
sharing avoidance and optimize refcount tracking
- Add lockless accesses annotation to sk_err[_soft]
- Optimize again the skb struct layout
- Extends the skb drop reasons to make it usable by multiple
subsystems
- Better const qualifier awareness for socket casts
BPF:
- Add skb and XDP typed dynptrs which allow BPF programs for more
ergonomic and less brittle iteration through data and
variable-sized accesses
- Add a new BPF netfilter program type and minimal support to hook
BPF programs to netfilter hooks such as prerouting or forward
- Add more precise memory usage reporting for all BPF map types
- Adds support for using {FOU,GUE} encap with an ipip device
operating in collect_md mode and add a set of BPF kfuncs for
controlling encap params
- Allow BPF programs to detect at load time whether a particular
kfunc exists or not, and also add support for this in light
skeleton
- Bigger batch of BPF verifier improvements to prepare for upcoming
BPF open-coded iterators allowing for less restrictive looping
capabilities
- Rework RCU enforcement in the verifier, add kptr_rcu and enforce
BPF programs to NULL-check before passing such pointers into kfunc
- Add support for kptrs in percpu hashmaps, percpu LRU hashmaps and
in local storage maps
- Enable RCU semantics for task BPF kptrs and allow referenced kptr
tasks to be stored in BPF maps
- Add support for refcounted local kptrs to the verifier for allowing
shared ownership, useful for adding a node to both the BPF list and
rbtree
- Add BPF verifier support for ST instructions in
convert_ctx_access() which will help new -mcpu=v4 clang flag to
start emitting them
- Add ARM32 USDT support to libbpf
- Improve bpftool's visual program dump which produces the control
flow graph in a DOT format by adding C source inline annotations
Protocols:
- IPv4: Allow adding to IPv4 address a 'protocol' tag. Such value
indicates the provenance of the IP address
- IPv6: optimize route lookup, dropping unneeded R/W lock acquisition
- Add the handshake upcall mechanism, allowing the user-space to
implement generic TLS handshake on kernel's behalf
- Bridge: support per-{Port, VLAN} neighbor suppression, increasing
resilience to nodes failures
- SCTP: add support for Fair Capacity and Weighted Fair Queueing
schedulers
- MPTCP: delay first subflow allocation up to its first usage. This
will allow for later better LSM interaction
- xfrm: Remove inner/outer modes from input/output path. These are
not needed anymore
- WiFi:
- reduced neighbor report (RNR) handling for AP mode
- HW timestamping support
- support for randomized auth/deauth TA for PASN privacy
- per-link debugfs for multi-link
- TC offload support for mac80211 drivers
- mac80211 mesh fast-xmit and fast-rx support
- enable Wi-Fi 7 (EHT) mesh support
Netfilter:
- Add nf_tables 'brouting' support, to force a packet to be routed
instead of being bridged
- Update bridge netfilter and ovs conntrack helpers to handle IPv6
Jumbo packets properly, i.e. fetch the packet length from
hop-by-hop extension header. This is needed for BIT TCP support
- The iptables 32bit compat interface isn't compiled in by default
anymore
- Move ip(6)tables builtin icmp matches to the udptcp one. This has
the advantage that icmp/icmpv6 match doesn't load the
iptables/ip6tables modules anymore when iptables-nft is used
- Extended netlink error report for netdevice in flowtables and
netdev/chains. Allow for incrementally add/delete devices to netdev
basechain. Allow to create netdev chain without device
Driver API:
- Remove redundant Device Control Error Reporting Enable, as PCI core
has already error reporting enabled at enumeration time
- Move Multicast DB netlink handlers to core, allowing devices other
then bridge to use them
- Allow the page_pool to directly recycle the pages from safely
localized NAPI
- Implement lockless TX queue stop/wake combo macros, allowing for
further code de-duplication and sanitization
- Add YNL support for user headers and struct attrs
- Add partial YNL specification for devlink
- Add partial YNL specification for ethtool
- Add tc-mqprio and tc-taprio support for preemptible traffic classes
- Add tx push buf len param to ethtool, specifies the maximum number
of bytes of a transmitted packet a driver can push directly to the
underlying device
- Add basic LED support for switch/phy
- Add NAPI documentation, stop relaying on external links
- Convert dsa_master_ioctl() to netdev notifier. This is a
preparatory work to make the hardware timestamping layer selectable
by user space
- Add transceiver support and improve the error messages for CAN-FD
controllers
New hardware / drivers:
- Ethernet:
- AMD/Pensando core device support
- MediaTek MT7981 SoC
- MediaTek MT7988 SoC
- Broadcom BCM53134 embedded switch
- Texas Instruments CPSW9G ethernet switch
- Qualcomm EMAC3 DWMAC ethernet
- StarFive JH7110 SoC
- NXP CBTX ethernet PHY
- WiFi:
- Apple M1 Pro/Max devices
- RealTek rtl8710bu/rtl8188gu
- RealTek rtl8822bs, rtl8822cs and rtl8821cs SDIO chipset
- Bluetooth:
- Realtek RTL8821CS, RTL8851B, RTL8852BS
- Mediatek MT7663, MT7922
- NXP w8997
- Actions Semi ATS2851
- QTI WCN6855
- Marvell 88W8997
- Can:
- STMicroelectronics bxcan stm32f429
Drivers:
- Ethernet NICs:
- Intel (1G, icg):
- add tracking and reporting of QBV config errors
- add support for configuring max SDU for each Tx queue
- Intel (100G, ice):
- refactor mailbox overflow detection to support Scalable IOV
- GNSS interface optimization
- Intel (i40e):
- support XDP multi-buffer
- nVidia/Mellanox:
- add the support for linux bridge multicast offload
- enable TC offload for egress and engress MACVLAN over bond
- add support for VxLAN GBP encap/decap flows offload
- extend packet offload to fully support libreswan
- support tunnel mode in mlx5 IPsec packet offload
- extend XDP multi-buffer support
- support MACsec VLAN offload
- add support for dynamic msix vectors allocation
- drop RX page_cache and fully use page_pool
- implement thermal zone to report NIC temperature
- Netronome/Corigine:
- add support for multi-zone conntrack offload
- Solarflare/Xilinx:
- support offloading TC VLAN push/pop actions to the MAE
- support TC decap rules
- support unicast PTP
- Other NICs:
- Broadcom (bnxt): enforce software based freq adjustments only on
shared PHC NIC
- RealTek (r8169): refactor to addess ASPM issues during NAPI poll
- Micrel (lan8841): add support for PTP_PF_PEROUT
- Cadence (macb): enable PTP unicast
- Engleder (tsnep): add XDP socket zero-copy support
- virtio-net: implement exact header length guest feature
- veth: add page_pool support for page recycling
- vxlan: add MDB data path support
- gve: add XDP support for GQI-QPL format
- geneve: accept every ethertype
- macvlan: allow some packets to bypass broadcast queue
- mana: add support for jumbo frame
- Ethernet high-speed switches:
- Microchip (sparx5): Add support for TC flower templates
- Ethernet embedded switches:
- Broadcom (b54):
- configure 6318 and 63268 RGMII ports
- Marvell (mv88e6xxx):
- faster C45 bus scan
- Microchip:
- lan966x:
- add support for IS1 VCAP
- better TX/RX from/to CPU performances
- ksz9477: add ETS Qdisc support
- ksz8: enhance static MAC table operations and error handling
- sama7g5: add PTP capability
- NXP (ocelot):
- add support for external ports
- add support for preemptible traffic classes
- Texas Instruments:
- add CPSWxG SGMII support for J7200 and J721E
- Intel WiFi (iwlwifi):
- preparation for Wi-Fi 7 EHT and multi-link support
- EHT (Wi-Fi 7) sniffer support
- hardware timestamping support for some devices/firwmares
- TX beacon protection on newer hardware
- Qualcomm 802.11ax WiFi (ath11k):
- MU-MIMO parameters support
- ack signal support for management packets
- RealTek WiFi (rtw88):
- SDIO bus support
- better support for some SDIO devices (e.g. MAC address from
efuse)
- RealTek WiFi (rtw89):
- HW scan support for 8852b
- better support for 6 GHz scanning
- support for various newer firmware APIs
- framework firmware backwards compatibility
- MediaTek WiFi (mt76):
- P2P support
- mesh A-MSDU support
- EHT (Wi-Fi 7) support
- coredump support"
* tag 'net-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2078 commits)
net: phy: hide the PHYLIB_LEDS knob
net: phy: marvell-88x2222: remove unnecessary (void*) conversions
tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.
net: amd: Fix link leak when verifying config failed
net: phy: marvell: Fix inconsistent indenting in led_blink_set
lan966x: Don't use xdp_frame when action is XDP_TX
tsnep: Add XDP socket zero-copy TX support
tsnep: Add XDP socket zero-copy RX support
tsnep: Move skb receive action to separate function
tsnep: Add functions for queue enable/disable
tsnep: Rework TX/RX queue initialization
tsnep: Replace modulo operation with mask
net: phy: dp83867: Add led_brightness_set support
net: phy: Fix reading LED reg property
drivers: nfc: nfcsim: remove return value check of `dev_dir`
net: phy: dp83867: Remove unnecessary (void*) conversions
net: ethtool: coalesce: try to make user settings stick twice
net: mana: Check if netdev/napi_alloc_frag returns single page
net: mana: Rename mana_refill_rxoob and remove some empty lines
net: veth: add page_pool stats
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly continue to prepare the thermal control subsystem for
using unified representation of trip points, which includes cleanups,
code refactoring and similar and update several drivers (for other
reasons), which includes new hardware support.
Specifics:
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano)
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano)
- Clean up the hwmon thermal driver (Daniel Lezcano)
- Add thermal zone id accessor and thermal zone type accessor and
prevent drivers from using thermal zone fields directly (Daniel
Lezcano)
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano)
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui)
- Add more thermal zone device encapsulation: prevent setting
structure field directly, access the sensor device instead the
thermal zone's device for trace, relocate the traces in
drivers/thermal (Daniel Lezcano)
- Use the generic trip point for the i.MX and remove the
get_trip_temp ops (Daniel Lezcano)
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li)
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown
(Wolfram Sang)
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur)
- Add MT8365 support (Amjad Ouled-Ameur)
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel)
- Add driver support for RK3588 (Finley Xiao)
- Use devm_reset_control_array_get_exclusive() for the Rockchip
driver (Ye Xingchen)
- Detect power gated thermal zones and return -EAGAIN when reading
the temperature (Mikko Perttunen)
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring)
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn)
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai)
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen)
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI)
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano)
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano)
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano)
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui)
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki)
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring)
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki)
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada)"
* tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: intel: int340x: Add DLVR support for RFIM control
thermal/core: Alloc-copy-free the thermal zone parameters structure
thermal/of: Unexport unused OF functions
thermal/drivers/bcm2835: Remove buggy call to thermal_of_zone_unregister
thermal/drivers/mediatek/lvts_thermal: Add AP domain for mt8195
dt-bindings: thermal: mediatek: Add AP domain to LVTS thermal controllers for mt8195
thermal: amlogic: Use dev_err_probe()
thermal/drivers/mediatek/lvts_thermal: Fix sensor 1 interrupt status bitmask
MAINTAINERS: adjust entry in THERMAL/POWER_ALLOCATOR after header movement
dt-bindings: thermal: Drop unneeded quotes
thermal/core: Remove thermal_bind_params structure
thermal/drivers/tegra-bpmp: Handle offline zones
thermal/drivers/rockchip: use devm_reset_control_array_get_exclusive()
dt-bindings: rockchip-thermal: Support the RK3588 SoC compatible
thermal/drivers/rockchip: Support RK3588 SoC in the thermal driver
thermal/drivers/rockchip: Support dynamic sized sensor array
thermal/drivers/rockchip: Simplify channel id logic
thermal/drivers/rockchip: Use dev_err_probe
thermal/drivers/rockchip: Simplify clock logic
thermal/drivers/rockchip: Simplify getting match data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have some new drivers, significant refactoring of existing intel
platforms, lots of improvements all around, mass conversion to using
immutable irqchips by drivers that had not been converted individually
yet and some changes in the core library code.
Summary:
New drivers:
- add a driver for the Loongson GPIO controller
- add a driver for the fxl6408 I2C GPIO expander
- add a GPIO module containing code common for Intel Elkhart Lake and
Merrifield platforms
- add a driver for the Intel Elkhart Lake platform reusing the code
from the intel tangier library
GPIOLIB core:
- GPIO ACPI improvements
- simplify gpiochip_add_data_with_keys() fwnode handling
- cleanup header inclusions (remove unneeded ones, order the rest
alphabetically)
- remove duplicate code (reuse krealloc() instead of open-coding it,
drop a duplicated check in gpiod_find_and_request())
- reshuffle the code to remove unnecessary forward declarations
- coding style cleanups and improvements
- add a helper for accessing device fwnodes
- small updates in docs
Driver improvements:
- convert all remaining GPIO irqchip drivers to using immutable
irqchips
- drop unnecessary of_match_ptr() macro expansions
- shrink the code in gpio-merrifield significantly by reusing the
code from gpio-tangier + minor tweaks to the driver code
- remove MODULE_LICENSE() from drivers that can only be built-in
- add device-tree support to gpio-loongson1
- use new regmap features in gpio-104-dio-48e and gpio-pcie-idio-24
- minor tweaks and fixes to gpio-xra1403, gpio-sim, gpio-tegra194,
gpio-omap, gpio-aspeed, gpio-raspberrypi-exp
- shrink code in gpio-ich and gpio-pxa
- Kconfig tweak for gpio-pmic-eic-sprd"
* tag 'gpio-updates-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (99 commits)
gpio: gpiolib: Simplify gpiochip_add_data_with_key() fwnode
gpiolib: Add gpiochip_set_data() helper
gpiolib: Move gpiochip_get_data() higher in the code
gpiolib: Check array_info for NULL only once in gpiod_get_array()
gpiolib: Replace open coded krealloc()
gpiolib: acpi: Add a ignore wakeup quirk for Clevo NL5xNU
gpiolib: acpi: Move ACPI device NULL check to acpi_get_driver_gpio_data()
gpiolib: acpi: use the fwnode in acpi_gpiochip_find()
gpio: mm-lantiq: Fix typo in the newly added header filename
sh: mach-x3proto: Add missing #include <linux/gpio/driver.h>
powerpc/40x: Add missing select OF_GPIO_MM_GPIOCHIP
gpio: xlp: Convert to immutable irq_chip
gpio: xilinx: Convert to immutable irq_chip
gpio: xgs-iproc: Convert to immutable irq_chip
gpio: visconti: Convert to immutable irq_chip
gpio: tqmx86: Convert to immutable irq_chip
gpio: thunderx: Convert to immutable irq_chip
gpio: stmpe: Convert to immutable irq_chip
gpio: siox: Convert to immutable irq_chip
gpio: rda: Convert to immutable irq_chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most notable updates this time are for Qualcomm Snapdragon
platforms. The Inline-Crypto-Engine gets a new DT binding and driver,
and a number of drivers now support additional Snapdragon variants, in
particular the rsc, scm, geni, bwm, glink and socinfo, while the llcc
(edac) and rpm drivers get notable functionality updates.
Updates on other platforms include:
- Various updates to the Mediatek mutex and mmsys drivers, including
support for the Helio X10 SoC
- Support for unidirectional mailbox channels in Arm SCMI firmware
- Support for per cpu asynchronous notification in OP-TEE firmware
- Minor updates for memory controller drivers.
- Minor updates for Renesas, TI, Amlogic, Apple, Broadcom, Tegra,
Allwinner, Versatile Express, Canaan, Microchip, Mediatek and i.MX
SoC drivers, mainly updating the use of MODULE_LICENSE() macros and
obsolete DT driver interfaces"
* tag 'soc-drivers-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: ti: smartreflex: Simplify getting the opam_sr pointer
bus: vexpress-config: Add explicit of_platform.h include
soc: mediatek: Kconfig: Add MTK_CMDQ dependency to MTK_MMSYS
memory: mtk-smi: mt8365: Add SMI Support
dt-bindings: memory-controllers: mediatek,smi-larb: add mt8365
dt-bindings: memory-controllers: mediatek,smi-common: add mt8365
memory: tegra: read values from correct device
dt-bindings: crypto: Add Qualcomm Inline Crypto Engine
soc: qcom: Make the Qualcomm UFS/SDCC ICE a dedicated driver
dt-bindings: firmware: document Qualcomm QCM2290 SCM
soc: qcom: rpmh-rsc: Support RSC v3 minor versions
soc: qcom: smd-rpm: Use GFP_ATOMIC in write path
soc/tegra: fuse: Remove nvmem root only access
soc/tegra: cbb: tegra194: Use of_address_count() helper
soc/tegra: cbb: Remove MODULE_LICENSE in non-modules
ARM: tegra: Remove MODULE_LICENSE in non-modules
soc/tegra: flowctrl: Use devm_platform_get_and_ioremap_resource()
soc: tegra: cbb: Drop empty platform remove function
firmware: arm_scmi: Add support for unidirectional mailbox channels
dt-bindings: firmware: arm,scmi: Support mailboxes unidirectional channels
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.4
Most likely the last -next pull request for v6.4. We have changes all
over. rtw88 now supports SDIO bus and iwlwifi continues to work on
Wi-Fi 7 support. Not much stack changes this time.
Major changes:
cfg80211/mac80211
- fix some Fine Time Measurement (FTM) frames not being bufferable
- flush frames before key removal to avoid potential unencrypted
transmission depending on the hardware design
iwlwifi
- preparation for Wi-Fi 7 EHT and multi-link support
rtw88
- SDIO bus support
- RTL8822BS, RTL8822CS and RTL8821CS SDIO chipset support
rtw89
- framework firmware backwards compatibility
brcmfmac
- Cypress 43439 SDIO support
mt76
- mt7921 P2P support
- mt7996 mesh A-MSDU support
- mt7996 EHT support
- mt7996 coredump support
wcn36xx
- support for pronto v3 hardware
ath11k
- PCIe DeviceTree bindings
- WCN6750: enable SAR support
ath10k
- convert DeviceTree bindings to YAML
* tag 'wireless-next-2023-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (261 commits)
wifi: rtw88: Update spelling in main.h
wifi: airo: remove ISA_DMA_API dependency
wifi: rtl8xxxu: Simplify setting the initial gain
wifi: rtl8xxxu: Add rtl8xxxu_write{8,16,32}_{set,clear}
wifi: rtl8xxxu: Don't print the vendor/product/serial
wifi: rtw88: Fix memory leak in rtw88_usb
wifi: rtw88: call rtw8821c_switch_rf_set() according to chip variant
wifi: rtw88: set pkg_type correctly for specific rtw8821c variants
wifi: rtw88: rtw8821c: Fix rfe_option field width
wifi: rtw88: usb: fix priority queue to endpoint mapping
wifi: rtw88: 8822c: add iface combination
wifi: rtw88: handle station mode concurrent scan with AP mode
wifi: rtw88: prevent scan abort with other VIFs
wifi: rtw88: refine reserved page flow for AP mode
wifi: rtw88: disallow PS during AP mode
wifi: rtw88: 8822c: extend reserved page number
wifi: rtw88: add port switch for AP mode
wifi: rtw88: add bitmap for dynamic port settings
wifi: rtw89: mac: use regular int as return type of DLE buffer request
wifi: mac80211: remove return value check of debugfs_create_dir()
...
====================
Link: https://lore.kernel.org/r/20230421104726.800BCC433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adjacent changes:
net/mptcp/protocol.h
63740448a32e ("mptcp: fix accept vs worker race")
2a6a870e44dd ("mptcp: stops worker on unaccepted sockets at listener close")
ddb1a072f858 ("mptcp: move first subflow allocation at mpc access time")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ath9k_mci_update_wlan_channels()
This partially reverts commit e161d4b60ae3a5356e07202e0bfedb5fad82c6aa.
Turns out the channelmap variable is not actually read-only, it's modified
through the MCI_GPM_CLR_CHANNEL_BIT() macro further down in the function,
so making it read-only causes page faults when that code is hit.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217183
Link: https://lore.kernel.org/r/20230413214118.153781-1-toke@toke.dk
Fixes: e161d4b60ae3 ("wifi: ath9k: Make arrays prof_prio and channelmap static const")
Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ath.git patches for v6.4. Major changes:
wcn36xx
* support for pronto v3 hardware
ath11k
* PCIe DeviceTree bindings
* WCN6750: enable SAR support
ath10k
* convert DeviceTree bindings to YAML
|
|
mt76 patches for 6.4
- fixes
- connac code unification
- mt7921 p2p support
- mt7996 mesh a-msdu support
- mt7996 eht support
- mt7996 coredump support
|
|
Update spelling in comments in main.h
Found by inspection.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418-rtw88-starspell-v1-1-70e52a23979b@kernel.org
|
|
This driver does not actually use the ISA DMA API, it is purely
PIO based, so remove the dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417205131.1560074-1-arnd@kernel.org
|
|
The goal of writing 0x6954341e / 0x6955341e to REG_OFDM0_XA_AGC_CORE1
appears to be setting the initial gain, which is stored in bits 0..6.
Bits 7..31 are the same as what the phy init tables write.
Modify only bits 0..6 so that we don't have to care about the values
of the others. This way we don't have to add another "else if" for the
RTL8192FU.
Why we need to change the initial gain from the default 0x20 to 0x1e?
Not sure. Some of the vendor drivers change it to 0x1e before scanning
and then restore it to the original value after.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/cf91ca69-70e3-4c20-c0b1-e59d452356a1@gmail.com
|
|
Also add rtl8xxxu_write32_mask, rtl8xxxu_write_rfreg_mask.
These helper functions make it easier to modify only parts of a register
by eliminating the call to the register reading function and the bit
manipulations.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/9430b841-1048-b27c-14ec-fca447dc32af@gmail.com
|
|
Most devices have a vendor name, product name, and serial number in the
efuse, but it's pretty useless. It duplicates the information already
printed by the USB subsystem:
usb 1-4: New USB device found, idVendor=0bda, idProduct=8178, bcdDevice= 2.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n WLAN Adapter
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 00e04c000001
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n WLAN Adapter
usb 1-4: New USB device found, idVendor=0bda, idProduct=818b, bcdDevice= 2.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n NIC
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 00e04c000001
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n NIC
-> usb 1-4: Serial not available.
usb 1-4: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 002E2DC0041F
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n
usb 1-4: New USB device found, idVendor=0bda, idProduct=8179, bcdDevice= 0.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n NIC
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 00E04C0001
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n NIC
-> usb 1-4: Serial: 00E04C0001
Also, that data is not interpreted correctly in all cases:
usb 3-1.1.2: New USB device found, idVendor=0bda, idProduct=8179, bcdDevice= 0.00
usb 3-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1.1.2: Product: 802.11n NIC
usb 3-1.1.2: Manufacturer: Realtek
usb 3-1.1.2: Vendor: Realtek
usb 3-1.1.2: Product: \x03802.11n NI
usb 3-1.1.2: Serial: \xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217231
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/a2a7d9df-0529-7890-3522-48dce613753f@gmail.com
|
|
Kmemleak shows the following leak arising from routine in the usb
probe routine:
unreferenced object 0xffff895cb29bba00 (size 512):
comm "(udev-worker)", pid 534, jiffies 4294903932 (age 102751.088s)
hex dump (first 32 bytes):
77 30 30 30 00 00 00 00 02 2f 2d 2b 30 00 00 00 w000...../-+0...
02 00 2a 28 00 00 00 00 ff 55 ff ff ff 00 00 00 ..*(.....U......
backtrace:
[<ffffffff9265fa36>] kmalloc_trace+0x26/0x90
[<ffffffffc17eec41>] rtw_usb_probe+0x2f1/0x680 [rtw_usb]
[<ffffffffc03e19fd>] usb_probe_interface+0xdd/0x2e0 [usbcore]
[<ffffffff92b4f2fe>] really_probe+0x18e/0x3d0
[<ffffffff92b4f5b8>] __driver_probe_device+0x78/0x160
[<ffffffff92b4f6bf>] driver_probe_device+0x1f/0x90
[<ffffffff92b4f8df>] __driver_attach+0xbf/0x1b0
[<ffffffff92b4d350>] bus_for_each_dev+0x70/0xc0
[<ffffffff92b4e51e>] bus_add_driver+0x10e/0x210
[<ffffffff92b50935>] driver_register+0x55/0xf0
[<ffffffffc03e0708>] usb_register_driver+0x88/0x140 [usbcore]
[<ffffffff92401153>] do_one_initcall+0x43/0x210
[<ffffffff9254f42a>] do_init_module+0x4a/0x200
[<ffffffff92551d1c>] __do_sys_finit_module+0xac/0x120
[<ffffffff92ee6626>] do_syscall_64+0x56/0x80
[<ffffffff9300006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
The leak was verified to be real by unloading the driver, which resulted
in a dangling pointer to the allocation.
The allocated memory is freed in rtw_usb_intf_deinit().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417160331.23071-1-Larry.Finger@lwfinger.net
|
|
We have to call rtw8821c_switch_rf_set() with SWITCH_TO_WLG or
SWITCH_TO_BTG according to the chip variant as denoted in rfe_option.
The information which argument to use for which variant has been
taken from the vendor driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-5-s.hauer@pengutronix.de
|
|
According to the vendor driver the pkg_type has to be set to '1'
for some rtw8821c variants. As the pkg_type has been hardcoded to
'0', add a field for it in struct rtw_hal and set this correctly
in the rtw8821c part.
With this parsing of a rtw_table is influenced and check_positive()
in phy.c returns true for some cases here. The same is done in the
vendor driver. However, this has no visible effect on the driver
here.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-4-s.hauer@pengutronix.de
|
|
On my RTW8821CU chipset rfe_option reads as 0x22. Looking at the
vendor driver suggests that the field width of rfe_option is 5 bit,
so rfe_option should be masked with 0x1f.
Without this the rfe_option comparisons with 2 further down the
driver evaluate as false when they should really evaluate as true.
The effect is that 2G channels do not work.
rfe_option is also used as an array index into rtw8821c_rfe_defs[].
rtw8821c_rfe_defs[34] (0x22) was added as part of adding USB support,
likely because rfe_option reads as 0x22. As this now becomes 0x2,
rtw8821c_rfe_defs[34] is no longer used and can be removed.
Note that this might not be the whole truth. In the vendor driver
there are indeed places where the unmasked rfe_option value is used.
However, the driver has several places where rfe_option is tested
with the pattern if (rfe_option == 2 || rfe_option == 0x22) or
if (rfe_option == 4 || rfe_option == 0x24), so that rfe_option BIT(5)
has no influence on the code path taken. We therefore mask BIT(5)
out from rfe_option entirely until this assumption is proved wrong
by some chip variant we do not know yet.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-3-s.hauer@pengutronix.de
|
|
The RTW88 chipsets have four different priority queues in hardware. For
the USB type chipsets the packets destined for a specific priority queue
must be sent through the endpoint corresponding to the queue. This was
not fully understood when porting from the RTW88 USB out of tree driver
and thus violated.
This patch implements the qsel to endpoint mapping as in
get_usb_bulkout_id_88xx() in the downstream driver.
Without this the driver often issues "timed out to flush queue 3"
warnings and often TX stalls completely.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-2-s.hauer@pengutronix.de
|
|
Allow 8822c to operate two interface concurrently, only 1 AP mode plus
1 station mode under same frequency is supported. Combination of other
types will not be added until requested.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121331.18062-1-pkshih@realtek.com
|
|
This patch allows vifs sharing same hardware with the AP mode vif to
do scan, do note that this could lead to packet loss or disconnection
of the AP's clients. Since we don't have chanctx, update scan info
upon set channel so bandwidth changes won't go unnoticed and get
misconfigured after scan. Download beacon just before scan starts to
allow hardware to get proper content to do beaconing. Last, beacons
should only be transmitted in AP's operating channel. Turn related
beacon functions off while we're in other channels so the receiving
stations won't get confused.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121323.18008-1-pkshih@realtek.com
|
|
Only abort scan with current scanning VIF. If we have more than one
interface, we could call rtw_hw_scan_abort() with the wrong VIF as
input. This avoids potential null pointer being accessed when actually
the other VIF is scanning.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121312.17954-1-pkshih@realtek.com
|
|
Only gather reserved pages from AP interface after it has started. Or
else ieee80211_beacon_get_*() returns NULL and causes other VIFs'
reserved pages fail to download. Update location of current reserved page
after beacon renews so offsets changed by beacon can be recognized.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121300.17900-1-pkshih@realtek.com
|
|
Firmware can't support PS mode during AP mode, so disallow this case.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-5-pkshih@realtek.com
|
|
Extend 8822c's reserved page number to accommodate additional required
pages. Reserved page is an area of memory in the FIFO dedicated for
special purposes. Previously only one interface is supported so 8 pages
should suffice, extend it so we can support 2 interfaces concurrently.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-4-pkshih@realtek.com
|
