| Age | Commit message (Collapse) | Author |
|---|
|
dev->gso_max_size is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_size()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The way to set tx spare buf via module parameter is not such
convenient as the way to set it via ethtool.
So,remove the way to set tx spare buf via module parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx buf len is for rx BD buffer size, support setting it via ethtool -G
parameter and getting it via ethtool -g parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
driver
Tx copybreak buf size is used for tx copybreak feature, the feature is
used for small size packet or frag. It adds a queue based tx shared
bounce buffer to memcpy the small packet when the len of xmitted skb is
below tx_copybreak(value to distinguish small size and normal size),
and reduce the overhead of dma map and unmap when IOMMU is on.
Support setting it via ethtool --set-tunable parameter and getting
it via ethtool --get-tunable parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x_vfpf_config_mac() was constified by not its stub.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Byte by byte assignments.
Fixes build on m68k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the TI DP83561-SP Gigabit ethernet phy device.
The dp83561-sp is a radiation hardened space grade gigabit ethernet
PHY. It has been tested for single event latch upto 121 MeV, the
critical reliability parameter for space designs. It interfaces directly to
twisted pair media through an external transformer. And the device also
interfaces directly to the MAC layer through Reduced GMII (RGMII) and MII.
DP83867, DP83869 and DP83561-SP, all these parts support 1000Base-T/
100Base-TX/ and 10Base-Te standards and have similar register map for
the core functionality.
The data sheet for this part is at https://www.ti.com/product/DP83561-SP
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Geet Modi <geet.modi@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211118102532.9835-1-hnagalla@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
do_div() does a 64-by-32 division. Here the divisor is an
unsigned long which on some platforms is 64 bit wide. So use
div64_ul instead of do_div to avoid a possible truncation.
Eliminate the following coccicheck warning:
./drivers/net/ethernet/renesas/ravb_main.c:2492:1-7: WARNING:
do_div() does a 64-by-32 division, please consider using div64_ul
instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/1637228883-100100-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Removing reduplicated error handling when running into error path
of `nfp_compile_flow_metadata`.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently pci_read/write_vpd_any() have been added to the PCI VPD API.
These functions allow to access VPD address space outside the
auto-detected VPD, and they can be used to significantly simplify the
eeprom ethtool ops.
Tested with a 88E8070 card with 1KB EEPROM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use 'for_each_clear_bit()' instead of hand writing it. It is much less
version.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct nig_stats around members egress_mac_pkt0_lo,
egress_mac_pkt0_hi, egress_mac_pkt1_lo, and egress_mac_pkt1_hi (and the
respective members in struct bnx2x_eth_stats), so they can be referenced
together. This will allow memcpy() and sizeof() to more easily reason
about sizes, improve readability, and avoid future warnings about writing
beyond the end of struct bnx2x_eth_stats's rx_stat_ifhcinbadoctets_hi.
"pahole" shows no size nor member offset changes to either struct.
"objdump -d" shows no meaningful object code changes (i.e. only source
line number induced differences and optimizations).
Additionally adds BUILD_BUG_ON() to compare the separate struct group
sizes.
Reviewed-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Link: https://lore.kernel.org/lkml/DM5PR18MB2229B0413C372CC6E49D59A3B2C59@DM5PR18MB2229.namprd18.prod.outlook.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct fw_eth_tx_pkt_vm_wr around members ethmacdst,
ethmacsrc, ethtype, and vlantci, so they can be referenced together. This
will allow memcpy() and sizeof() to more easily reason about sizes,
improve readability, and avoid future warnings about writing beyond the
end of ethmacdst.
"pahole" shows no size nor member offset changes to struct
fw_eth_tx_pkt_vm_wr. "objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct rss_hdr around members imm_data and intr_gen,
so they can be referenced together. This will allow memcpy() and sizeof()
to more easily reason about sizes, improve readability, and avoid future
warnings about writing beyond the end of imm_data.
"pahole" shows no size nor member offset changes to struct rss_hdr.
"objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1000base-KX was missed in phylink_caps_to_linkmodes(), add it. This
will be necessary to convert stmmac with xpcs to ensure we don't drop
any supported linkmodes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Byte by byte assignments.
Fixes build on m68k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Byte by byte assignments.
Fixes build on m68k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Byte by byte assignments.
Fixes build on m68k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_addr is set from IO reads, passed to an arch-specific helper.
Note that the helper never reads it so uninitialized temp is fine.
Fixes build on parisc.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_addr is set from IO reads, and broken from a u16 value.
Fixes build on Alpha.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IO reads, so save to an array then eth_hw_addr_set().
Fixes build on x86 (32bit).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use temp to pass to the reading function, the function is generic
so can't fix there.
Fixes m68k build.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Loop with offsetting to every second byte, so use a temp buffer.
Fixes m68k build.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IO reads, so save to an array then eth_hw_addr_set().
Fixes build on Alpha.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Byte by byte assignments.
Fixes build on m68k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Byte by byte assignments.
Fixes build on m68k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Byte by byte assignments.
Fixes build on m68k.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_addr is initialized byte by byte from series.
Fixes build on x86 (32bit).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IO reads, so save to an array then eth_hw_addr_set().
Fixes build on x86 (32bit).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IO reads, so save to an array then eth_hw_addr_set().
Fixes build on x86 (32bit).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add const to the address param of ipw_send_adapter_address()
all the functions down the chain have already been changed.
Not sure how I lost this in the rebase.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
wilc_set_mac_address() calls IO routines which don't guarantee
the pointer won't be written to. Make a copy.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Argument comes from netdev->dev_addr directly, it needs a const.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The future is here, convert the new driver as we are about
to make netdev->dev_addr const.
Acked-by: Lukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch introduces a NAPI-style approach for processing completed
Rx URBs that contributes to improving driver throughput and reducing
CPU load.
Packets in completed URBs are copied to NAPI SKBs and passed to the
network stack for processing. Each frame passed to the stack is one
work item in the NAPI budget.
If the NAPI budget is consumed and frames remain, they are added to
an overflow queue that is processed at the start of the next NAPI
polling cycle.
The NAPI handler is also responsible for copying pending Tx data to
Tx URBs and submitting them to the USB host controller for
transmission.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove hardware-specific header length adjustment as it is no longer
required. It also breaks generic receive offload (GRO) processing of
received TCP frames that results in a TCP ACK being sent for each
received frame.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move position of rx_submit() to remove forward declaration of
rx_complete() which is now no longer required.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a new approach to allocating and managing
Rx URBs that contributes to improving driver throughput and reducing
CPU load.
A pool of Rx URBs is created during driver instantiation. All the
URBs are initially submitted to the USB host controller for
processing.
The default URB buffer size is different for each USB bus speed.
The chosen sizes provide good USB utilisation with little impact on
overall packet latency.
Completed URBs are processed in the driver bottom half. The URB
buffer contents are copied to a dynamically allocated SKB, which is
then passed to the network stack. The URB is then re-submitted to
the USB host controller.
NOTE: the call to skb_copy() in rx_process() that copies the URB
contents to a new SKB is a temporary change to make this patch work
in its own right. This call will be removed when the NAPI processing
is introduced by patch 6 in this patch set.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a new approach to allocating and managing
Tx URBs that contributes to improving driver throughput and reducing
CPU load.
A pool of Tx URBs is created during driver instantiation. A URB is
allocated from the pool when there is data to transmit. The URB is
released back to the pool when the data has been transmitted by the
device.
The default URB buffer size is different for each USB bus speed.
The chosen sizes provide good USB utilisation with little impact on
overall packet latency.
SKBs to be transmitted are added to a pending queue for processing.
The driver tracks the available Tx URB buffer space and copies as
much pending data as possible into each free URB. Each full URB
is then submitted to the USB host controller for transmission.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix memory allocation that fails to check for NULL return.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PSFP rules take effect on the streams from any port of VSC9959 switch.
This patch use ingress port to limit the rule only active on this port.
Each stream can only match two ingress source ports in VSC9959. Streams
from lowest port gets the configuration of SFID pointed by MAC Table
lookup and streams from highest port gets the configuration of (SFID+1)
pointed by MAC Table lookup. This patch defines the PSFP rule on highest
port as dummy rule, which means that it does not modify the MAC table.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add police action to set flow meter table which is defined
in IEEE802.1Qci. Flow metering is two rates two buckets and three color
marker to policing the frames, we only enable one rate one bucket in
this patch.
Flow metering shares a same policer pool with VCAP policers, so the PSFP
policer calls ocelot_vcap_policer_add() and ocelot_vcap_policer_del() to
set flow meter police.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Policer was previously automatically assigned from the highest index to
the lowest index from policer pool. But police action of tc flower now
uses index to set an police entry. This patch uses the police index to
set vcap policers, so that one policer can be shared by multiple rules.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds stream gate settings for PSFP. Use SGI table to store
stream gate entries. Disable the gate entry when it is not used by any
stream.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VSC9959 supports Per-Stream Filtering and Policing(PSFP) that complies
with the IEEE 802.1Qci standard. The stream is identified by Null stream
identification(DMAC and VLAN ID) defined in IEEE802.1CB.
For PSFP, four tables need to be set up: stream table, stream filter
table, stream gate table, and flow meter table. Identify the stream by
parsing the tc flower keys and add it to the stream table. The stream
filter table is automatically maintained, and its index is determined by
SGID(flow gate index) and FMID(flow meter index).
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PSFP support gate and police action. This patch add the gate and police
action to flower parse action, check chain ID to determine which block
to offload. Adding psfp callback functions to add, delete and update gate
and police in PSFP table if hardware supports it.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some chips in the ocelot series such as VSC9959 support Per-Stream
Filtering and Policing(PSFP), which is processing after VCAP blocks.
We set this block on chain 30000 and set vcap IS2 chain to goto PSFP
chain if hardware support.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_mact_learn_streamdata() can be used in VSC9959 to overwrite an
FDB entry with stream data. The stream data includes SFID and SSID which
can be used for PSFP and FRER set.
ocelot_mact_lookup() can be used to check if the given {DMAC, VID} FDB
entry is exist, and also can retrieve the DEST_IDX and entry type for
the FDB entry.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
