| Age | Commit message (Collapse) | Author |
|---|
|
While adding support for "performance states" in the OPP and genpd core,
it was decided to set the `pstate` field via genpd's
pm_genpd_opp_to_performance_state() helper, to allow platforms to set
`pstate` even if they don't have a corresponding `level` field in the DT
OPP tables (More details are present in commit 6e41766a6a50 ("PM /
Domain: Implement of_genpd_opp_to_performance_state()")).
Revisiting that five years later clearly suggests that it was
over-designed as all current users are eventually using the `level`
value only.
The previous commit already added necessary checks to make sure pstate
is only used for genpd tables. Lets now simplify this a little, and use
`level` directly and remove `pstate` field altogether.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is not very clear right now that the `pstate` field is only valid for
genpd OPP tables and not consumer tables. And there is no checking for
the same at various places.
Add checks in place to verify that and make it clear to the reader.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com>
|
|
This code was added (long back) by commit 009acd196fc8 ("PM / OPP:
Support updating performance state of device's power domain") and at
that time the `opp->pstate` field was used to store the performance
state required by a device's OPP.
Over time that changed and the `->pstate` field is now used only for
genpd devices and consumer devices access that via the required-opps
instead.
Because of all these changes, _opp_table_kref_release() now drops the
constraint only when the genpd's OPP table gets freed and not the
device's. Which is definitely not what we wanted. And dropping the
constraint doesn't have much meaning as the genpd itself is going away.
Moreover, if we want to drop constraints here, then just dropping the
performance constraint alone isn't sufficient as there are other
resource constraints like clk, regulator, etc. too, which must be
handled.
Probably the right thing to do here is to leave this decision to the
consumers, which can call `dev_pm_opp_set_rate(dev, 0)` or similar APIs
to drop all constraints properly. Which many of the consumers already
do.
Remove the special code, which is broken anyway.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
`lazy_opp_tables` is only used in of.c, move it there and mark it
`static`.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
When dev_pm_opp_of_find_icc_paths() in _allocate_opp_table() returns
-EPROBE_DEFER, the opp_table is freed again, to wait until all the
interconnect paths are available.
However, if the OPP table is using required-opps then it may already
have been added to the global lazy_opp_tables list. The error path
does not remove the opp_table from the list again.
This can cause crashes later when the provider of the required-opps
is added, since we will iterate over OPP tables that have already been
freed. E.g.:
Unable to handle kernel NULL pointer dereference when read
CPU: 0 PID: 7 Comm: kworker/0:0 Not tainted 6.4.0-rc3
PC is at _of_add_opp_table_v2 (include/linux/of.h:949
drivers/opp/of.c:98 drivers/opp/of.c:344 drivers/opp/of.c:404
drivers/opp/of.c:1032) -> lazy_link_required_opp_table()
Fix this by calling _of_clear_opp_table() to remove the opp_table from
the list and clear other allocated resources. While at it, also add the
missing mutex_destroy() calls in the error path.
Cc: stable@vger.kernel.org
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Fixes: 7eba0c7641b0 ("opp: Allow lazy-linking of required-opps")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Otherwise, when enabling a debug build and dynamic debug in the kernel, it
quickly floods the kernel ring buffer and makes debugging of other
subsystems almost impossible, unless manually disabled.
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The required-opps configuration is closely tied to genpd and performance
states at the moment and it is not very obvious that required-opps can
live without genpds. Though we don't support configuring required-opps
for non-genpd cases currently.
This commit aims at separating these parts, where configuring genpds
would be a special case of configuring the required-opps.
Add a specialized callback, set_required_opps(), to the opp table and
set it to different callbacks accordingly.
This shouldn't result in any functional changes for now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There is no real need of keeping separate code for single genpd case, it
can be made to work with a simple change.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
smatch complains that 'ret' may be returned un-initialized.
Explicitly return 0 if we reach the end of the function (should
'opp_table->clk_count' be 0).
Fixes: 8174a3a613af ("OPP: Provide a simple implementation to configure multiple clocks")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The struct dev_pm_opp contains a reference of the DT node, opp->np,
throughout its lifetime. We should increase the refcount for the same
from _opp_add_static_v2(), and drop it while removing the OPP finally.
Signed-off-by: Liang He <windhl@126.com>
[ Viresh: Updated subject / commit log, create _of_clear_opp() and drop
reference from it]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
There is a corner case with Tegra30, where we want to skip clk
configuration via dev_pm_opp_set_opp(), but still want the OPP core to
read the "opp-hz" property so we can find the right OPP via freq finding
helpers.
This is the easiest of the ways to make it work, without any special
hacks in the OPP core. Allow config_clks to be passed for single clk
case.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This provides a simple implementation to configure multiple clocks for a
device.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Many helpers can be safely called only for devices that have a single
clk associated with them. Assert the same for those routines.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The helpers for the clock key, at least, would need to assert that the
helpers are called only for single clock case. Prepare for that by
adding an argument to the key finding helpers.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Replicate the same behavior as "rates" here and compare all values
instead of relying on the first entry alone.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This patch adds support to allow multiple clocks for a device.
The design is pretty much similar to how this is done for regulators,
and platforms can supply their own version of the config_clks() callback
if they have multiple clocks for their device. The core manages the
calls via opp_table->config_clks() eventually.
We have kept both "clk" and "clks" fields in the OPP table structure and
the reason is provided as a comment in _opp_set_clknames(). The same
isn't done for "rates" though and we use rates[0] at most of the places
now.
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
dev_pm_opp_set_opp() can be called for any device, it may or may not
have a frequency value associated with it.
If a frequency value isn't available, we pass 0 to _set_opp(). Make it
optional instead by making _set_opp() accept a pointer instead, as the
frequency value is anyway available in the OPP. This makes
dev_pm_opp_set_opp() and _set_opp() completely independent of any
special key value.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Reuse _opp_compare_key() in _opp_add_static_v2() instead of just
comparing frequency while finding suspend frequency. Also add a comment
over _opp_compare_key() explaining its return values.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
commit 32715be4fe95 ("opp: Fix adding OPP entries in a wrong order if
rate is unavailable") removed the only user of this field, get rid of
rest of it now.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The OPP table is called "opp_table" at most of the places and "table" at
few. Make all of them follow the same naming convention, "opp_table".
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Use the recently added generic key findings helpers to find bandwidth
key values.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Use the recently added generic key findings helpers to find level key
values.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
There are three type of helpers, to find exact, ceil, and floor values,
replicated for multiple key types, freq, level, bw. And all of these
helpers share a lot of boilerplate code.
Add generic key finding helpers to reduce code redundancy.
Also update the freq finder helpers to use the new infrastructure.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This was added few years back, but the code that was supposed to use it
never got merged. Remove the unused helper.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The only user of the custom helper is migrated to use
dev_pm_opp_set_config_regulators() interface. Remove the now unused
custom OPP helper support.
This cleans up _set_opp() and leaves a single code path to be used by
all users.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We already have an API for getting voltage information for a single
regulator, dev_pm_opp_get_voltage(), but there is nothing available for
multiple regulator case.
This patch adds a new API, dev_pm_opp_get_supplies(), to get all
information related to the supplies for an OPP.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
In order to reuse the same code path, i.e. clk_set_rate() from
_set_opp(), migrate _generic_set_opp_regulator() to implement a
config_regulators() interface.
It is renamed to _opp_config_regulator_single() and is set as the
preferred config_regulators() interface whenever we have a single
regulator available.
Note that this also drops code responsible for restoring the
voltage/freq in case of errors. We aren't handling that properly
currently, restoring only some of the resources while leaving others out
(like bandwidth and required OPPs). It is better to drop all of it
instead of partial restoration.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Extend the dev_pm_opp_set_config() interface to allow adding
config_regulators() helpers. This helper will be called to set the
voltages of the regulators from the regular path in _set_opp(), while we
are trying to change the OPP.
This will eventually replace the custom set_opp() helper.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Now that we have a central API to handle all OPP table configurations,
migrate the set-prop-name family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Acked-by: Samuel Holland <samuel@sholland.org> # sun50i
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Now that we have a central API to handle all OPP table configurations,
migrate the attach-genpd family of helpers to use the new
infrastructure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Now that we have a central API to handle all OPP table configurations,
migrate the set-opp-helper family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Remove devm_pm_opp_register_set_opp_helper() as it has no users
currently.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Now that we have a central API to handle all OPP table configurations,
migrate the set-clk-name family of helpers to use the new
infrastructure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Now that we have a central API to handle all OPP table configurations,
migrate the set-supported-hw family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Now that we have a central API to handle all OPP table configurations,
migrate the set-regulators family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The OPP core already have few configuration specific APIs and it is
getting complex or messy for both the OPP core and its users.
Lets introduce a new set of API which will be used for all kind of
different configurations, and shall eventually be used by all the
existing ones.
The new API, returns a unique token instead of a pointer to the OPP
table, which allows the OPP core to drop the resources selectively later
on.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Make dev_pm_opp_set_regulators() accept a NULL terminated list of names
instead of making the callers keep the two parameters in sync, which
creates an opportunity for bugs to get in.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Steven Price <steven.price@arm.com> # panfrost
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Track if the clock name is configured by the platform or not. This is a
preparatory change and will be used by later commits. This also makes
the behavior of the clkname API similar to other ones, which allow
repeated calls to the same API for each CPU.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Replace rate with state.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Make @freq to @bw in dev_pm_opp_find_bw_ceil() and
dev_pm_opp_find_bw_floor() kernel-doc comment to
remove warnings found by running scripts/kernel-doc,
which is caused by using 'make W=1'.
drivers/opp/core.c:753: warning: Function parameter or member 'bw' not
described in 'dev_pm_opp_find_bw_ceil'
drivers/opp/core.c:753: warning: Excess function parameter 'freq'
description in 'dev_pm_opp_find_bw_ceil'
drivers/opp/core.c:812: warning: Function parameter or member 'bw' not
described in 'dev_pm_opp_find_bw_floor'
drivers/opp/core.c:812: warning: Excess function parameter 'freq'
description in 'dev_pm_opp_find_bw_floor'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
dev_pm_domain_attach_by_name() may return NULL in some cases,
so IS_ERR() doesn't meet the requirements. Thus fix it.
Fixes: 6319aee10e53 ("opp: Attach genpds to devices from within OPP core")
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
[ Viresh: Replace ENODATA with ENODEV ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Reorder the helpers to keep all freq specific ones, followed by level
and bw.
No functional change.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add dev_pm_opp_find_bw_ceil and dev_pm_opp_find_bw_floor to retrieve opps
based on interconnect associated with the opp and bandwidth. The index
variable is the index of the interconnect as specified in the opp table
in Devicetree.
Co-developed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add new property to the OPP: power value. The OPP entry in the DT can have
"opp-microwatt". Add the needed code to handle this new property in the
existing infrastructure.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Elements of the 'names' array are not changed by the code, constify them
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Commit 4fa82a87ba55 ("opp: Allow required-opps to be used for non genpd
use cases") dereferences the pointers in required_opp_tables but these
might be set to an ERR_PTR if the list still has lazy links pending,
resulting in segfaults. Prior to this patch IS_ERR was also checked on
required_opp_tables[i] before reading ->is_genpd inside
_opp_table_alloc_required_tables, which is at the same time the
predicate to add this table to the lazy list. This segfault is solved
by reordering the checks to bail on lazy pending tables before reading
->is_genpd.
Fixes: 4fa82a87ba55 ("opp: Allow required-opps to be used for non genpd use cases")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The current_opp is released only when whole OPP table is released,
otherwise it's only marked as removed by dev_pm_opp_remove_table().
Functions like dev_pm_opp_put_clkname() and dev_pm_opp_put_supported_hw()
are checking whether OPP table is empty and it's not if current_opp is
set since it holds the refcount of OPP, this produces a noisy warning
from these functions about busy OPP table. Remove the checks to fix it.
Cc: stable@vger.kernel.org
Fixes: 81c4d8a3c414 ("opp: Keep track of currently programmed OPP")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Don't limit required_opp_table to genpd only. One possible use case is
cpufreq based devfreq governor, which can use required-opps property to
derive devfreq from cpufreq.
Though the OPP core still doesn't support non-genpd required-opps in
_set_required_opps().
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[ Viresh: Update _set_required_opps() to check for genpd ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Make devm_pm_opp_attach_genpd() to return error code instead of
opp_table pointer in order to have return type consistent with the
other resource-managed OPP helpers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
