| Age | Commit message (Collapse) | Author |
|---|
|
Currently, the dw_pcie::max_link_speed has a valid value only if the
controller driver restricts the maximum link speed in the driver or if
the platform does so in the devicetree using the 'max-link-speed'
property.
But having the maximum supported link speed of the platform would be
helpful for the vendor drivers to configure any link specific settings.
So in the case of non-valid value in dw_pcie::max_link_speed, just cache
the hardware default value from Link Capability register.
While at it, remove the 'max_link_speed' argument to the
dw_pcie_link_set_max_speed() function since the value can be
retrieved within the function.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-2-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
|
|
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
|
|
PARF hardware block which is a wrapper on top of DWC PCIe controller
mirrors the DBI and ATU register space. It uses PARF_SLV_ADDR_SPACE_SIZE
register to get the size of the memory block to be mirrored and uses
PARF_DBI_BASE_ADDR, PARF_ATU_BASE_ADDR registers to determine the base
address of DBI and ATU space inside the memory block that is being
mirrored.
When a memory region which is located above the SLV_ADDR_SPACE_SIZE
boundary is used for BAR region then there could be an overlap of DBI and
ATU address space that is getting mirrored and the BAR region. This
results in DBI and ATU address space contents getting updated when a PCIe
function driver tries updating the BAR/MMIO memory region. Reference
memory map of the PCIe memory region with DBI and ATU address space
overlapping BAR region is as below.
|---------------|
| |
| |
------- --------|---------------|
| | |---------------|
| | | DBI |
| | |---------------|---->DBI_BASE_ADDR
| | | |
| | | |
| PCIe | |---->2*SLV_ADDR_SPACE_SIZE
| BAR/MMIO|---------------|
| Region | ATU |
| | |---------------|---->ATU_BASE_ADDR
| | | |
PCIe | |---------------|
Memory | | DBI |
Region | |---------------|---->DBI_BASE_ADDR
| | | |
| --------| |
| | |---->SLV_ADDR_SPACE_SIZE
| |---------------|
| | ATU |
| |---------------|---->ATU_BASE_ADDR
| | |
| |---------------|
| | DBI |
| |---------------|---->DBI_BASE_ADDR
| | |
| | |
----------------|---------------|
| |
| |
| |
|---------------|
Currently memory region beyond the SLV_ADDR_SPACE_SIZE boundary is not
used for BAR region which is why the above mentioned issue is not
encountered. This issue is discovered as part of internal testing when we
tried moving the BAR region beyond the SLV_ADDR_SPACE_SIZE boundary. Hence
we are trying to fix this.
As PARF hardware block mirrors DBI and ATU register space after every
PARF_SLV_ADDR_SPACE_SIZE (default 0x1000000) boundary multiple, program
maximum possible size to this register by writing 0x80000000 to it(it
considers only powers of 2 as values) to avoid mirroring DBI and ATU to
BAR/MMIO region. Write the physical base address of DBI and ATU register
blocks to PARF_DBI_BASE_ADDR (default 0x0) and PARF_ATU_BASE_ADDR (default
0x1000) respectively to make sure DBI and ATU blocks are at expected
memory locations.
The register offsets PARF_DBI_BASE_ADDR_V2, PARF_SLV_ADDR_SPACE_SIZE_V2
and PARF_ATU_BASE_ADDR are applicable for platforms that use Qcom IP
rev 1.9.0, 2.7.0 and 2.9.0. PARF_DBI_BASE_ADDR_V2 and
PARF_SLV_ADDR_SPACE_SIZE_V2 are applicable for Qcom IP rev 2.3.3.
PARF_DBI_BASE_ADDR and PARF_SLV_ADDR_SPACE_SIZE are applicable for Qcom
IP rev 1.0.0, 2.3.2 and 2.4.0. Update init()/post_init() functions of the
respective Qcom IP versions to program applicable PARF_DBI_BASE_ADDR,
PARF_SLV_ADDR_SPACE_SIZE and PARF_ATU_BASE_ADDR register offsets. Update
the SLV_ADDR_SPACE_SZ macro to 0x80000000 to set highest bit in
PARF_SLV_ADDR_SPACE_SIZE register.
Cache DBI and iATU physical addresses in 'struct dw_pcie' so that
pcie_qcom.c driver can program these addresses in the PARF_DBI_BASE_ADDR
and PARF_ATU_BASE_ADDR registers.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20240814220338.1969668-1-quic_pyarlaga@quicinc.com
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
|
|
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)
- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
(HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't auto
detect this (Manivannan Sadhasivam)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
(Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if the
link is already disabled (Manivannan Sadhasivam)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
even if other drivers don't vote for it (Krishna chaitanya chundru)
- Add Operating Performance Points (OPP) to scale performance state based
on aggregate link bandwidth to improve SoC power efficiency (Krishna
chaitanya chundru)
- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
(Dan Carpenter)
- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
Carpenter)
* pci/controller/qcom:
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: qcom: Add OPP support to scale performance
PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
PCI: qcom-ep: Disable resources unconditionally during PERST# assert
PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
PCI: epf-mhi: Enable HDMA for SA8775P SoC
PCI: qcom-ep: Add HDMA support for SA8775P SoC
PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
PCI: dwc: Skip finding eDMA channels count for HDMA platforms
PCI: dwc: Refactor dw_pcie_edma_find_chip() API
PCI: qcom-ep: Add support for SA8775P SOC
dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
PCI: qcom: Use devm_clk_bulk_get_all() API
|
|
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Instead of maintaining a separate capability for glue drivers that cannot
support auto detection of the eDMA mapping format, pass the mapping format
directly from them.
This will simplify the code and also allow adding HDMA support that also
doesn't support auto detection of mapping format.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-3-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
In the case of Hyper DMA (HDMA) present in DWC controllers, there is no way
the drivers can auto detect the number of read/write channels as like its
predecessor embedded DMA (eDMA). So the glue drivers making use of HDMA
have to pass the channels count during probe.
To accommodate that, skip the existing auto detection of channels count
procedure for HDMA based platforms. If the channels count passed by the
glue drivers were wrong in any form, then the existing sanity check will
catch it.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-2-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
In order to add support for Hyper DMA (HDMA), refactor the existing
dw_pcie_edma_find_chip() API by moving the common code to separate
functions.
No functional change.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-1-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
Since no PCIe controller drivers call this, this change is not required
for now. But, Renesas R-Car Gen4 PCIe controller driver will call this
and if the controller driver is built as a kernel module, the following
build error happens:
ERROR: modpost: "dw_pcie_write_dbi2" [drivers/pci/controller/dwc/pcie-rcar-gen4-host-drv.ko] undefined!
So, expose dw_pcie_write_dbi2() for it.
Link: https://lore.kernel.org/linux-pci/20230926122431.3974714-8-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
Renesas R-Car Gen4 PCIe controllers have an unexpected register value in
the eDMA CTRL register.
So, add a new capability flag "EDMA_UNROLL" which would force the unrolled
eDMA mapping for the problematic device.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-7-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
Update dw_pcie_link_set_max_link_width() to set PCI_EXP_LNKCAP_MLW.
In accordance with the DW PCIe RC/EP HW manuals [1,2,3,...] aside with
the PORT_LINK_CTRL_OFF.LINK_CAPABLE and GEN2_CTRL_OFF.NUM_OF_LANES[8:0]
field there is another one which needs to be updated.
It's LINK_CAPABILITIES_REG.PCIE_CAP_MAX_LINK_WIDTH. If it isn't done at
the very least the maximum link-width capability CSR won't expose the
actual maximum capability.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.60a, March 2015, p.1032
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.70a, March 2016, p.1065
[3] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.90a, March 2016, p.1057
...
[X] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint,
Version 5.40a, March 2019, p.1396
[X+1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 5.40a, March 2019, p.1266
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
This is a preparation before adding the Max-Link-width capability
setup which would in its turn complete the max-link-width setup
procedure defined by Synopsys in the HW-manual.
Seeing there is a max-link-speed setup method defined in the DW PCIe
core driver it would be good to have a similar function for the link
width setup.
That's why we need to define a dedicated function first from already
implemented but incomplete link-width setting up code.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Add locking to read/modify/write PCIe Capability Register accessors
for Link Control and Root Control
- Use pci_dev_id() when possible instead of manually composing ID
from dev->bus->number and dev->devfn
Resource management:
- Move prototypes for __weak sysfs resource files to linux/pci.h to
fix 'no previous prototype' warnings
- Make more I/O port accesses depend on HAS_IOPORT
- Use devm_platform_get_and_ioremap_resource() instead of open-coding
platform_get_resource() followed by devm_ioremap_resource()
Power management:
- Ensure devices are powered up while accessing VPD
- If device is powered-up, keep it that way while polling for PME
- Only read PCI_PM_CTRL register when available, to avoid reading the
wrong register and corrupting dev->current_state
Virtualization:
- Avoid Secondary Bus Reset on NVIDIA T4 GPUs
Error handling:
- Remove unused pci_disable_pcie_error_reporting()
- Unexport pci_enable_pcie_error_reporting(), used only by aer.c
- Unexport pcie_port_bus_type, used only by PCI core
VGA:
- Simplify and clean up typos in VGA arbiter
Apple PCIe controller driver:
- Initialize pcie->nvecs (number of available MSIs) before use
Broadcom iProc PCIe controller driver:
- Use of_property_read_bool() instead of low-level accessors for
boolean properties
Broadcom STB PCIe controller driver:
- Assert PERST# when probing BCM2711 because some bootloaders don't
do it
Freescale i.MX6 PCIe controller driver:
- Add .host_deinit() callback so we can clean up things like
regulators on probe failure or driver unload
Freescale Layerscape PCIe controller driver:
- Add support for link-down notification so the endpoint driver can
process LINK_DOWN events
- Add suspend/resume support, including manual
PME_Turn_off/PME_TO_Ack handshake
- Save Link Capabilities during probe so they can be restored when
handling a link-up event, since the controller loses the Link Width
and Link Speed values during reset
Intel VMD host bridge driver:
- Fix disable of bridge windows during domain reset; previously we
cleared the base/limit registers, which actually left the windows
enabled
Marvell MVEBU PCIe controller driver:
- Remove unused busn member
Microchip PolarFlare PCIe controller driver:
- Fix interrupt bit definitions so the SEC and DED interrupt handlers
work correctly
- Make driver buildable as a module
- Read FPGA MSI configuration parameters from hardware instead of
hard-coding them
Microsoft Hyper-V host bridge driver:
- To avoid a NULL pointer dereference, skip MSI restore after
hibernate if MSI/MSI-X hasn't been enabled
NVIDIA Tegra194 PCIe controller driver:
- Revert 'PCI: tegra194: Enable support for 256 Byte payload' because
Linux doesn't know how to reduce MPS from to 256 to 128 bytes for
endpoints below a switch (because other devices below the switch
might already be operating), which leads to 'Malformed TLP' errors
Qualcomm PCIe controller driver:
- Add DT and driver support for interconnect bandwidth voting for
'pcie-mem' and 'cpu-pcie' interconnects
- Fix broken SDX65 'compatible' DT property
- Configure controller so MHI bus master clock will be switched off
while in ASPM L1.x states
- Use alignment restriction from EPF core in EPF MHI driver
- Add Endpoint eDMA support
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driver
- Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup
latency
- Add sa8775p DT binding and driver support
Rockchip PCIe controller driver:
- Use 64-bit mask on MSI 64-bit PCI address to avoid zeroing out the
upper 32 bits
SiFive FU740 PCIe controller driver:
- Set the supported number of MSI vectors so we can use all available
MSI interrupts
Synopsys DesignWare PCIe controller driver:
- Add generic dwc suspend/resume APIs (dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq()) to be called by controller driver
suspend/resume ops, and a controller callback to send PME_Turn_Off
MicroSemi Switchtec management driver:
- Add support for PCIe Gen5 devices
Miscellaneous:
- Reorder and compress to reduce size of struct pci_dev
- Fix race in DOE destroy_work_on_stack()
- Add stubs to avoid casts between incompatible function types
- Explicitly include correct DT includes to untangle headers"
* tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (96 commits)
PCI: qcom-ep: Add ICC bandwidth voting support
dt-bindings: PCI: qcom: ep: Add interconnects path
PCI: qcom-ep: Treat unknown IRQ events as an error
dt-bindings: PCI: qcom: Fix SDX65 compatible
PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API
PCI: epf-mhi: Use iATU for small transfers
PCI: epf-mhi: Add support for SM8450
PCI: epf-mhi: Add eDMA support
PCI: qcom-ep: Add eDMA support
PCI: epf-mhi: Make use of the alignment restriction from EPF core
PCI/PM: Only read PCI_PM_CTRL register when available
PCI: qcom: Add support for sa8775p SoC
dt-bindings: PCI: qcom: Add sa8775p compatible
PCI: qcom-ep: Pass alignment restriction to the EPF core
PCI: Simplify pcie_capability_clear_and_set_word() control flow
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
...
|
|
This reverts commit da56a1bfbab55189595e588f1d984bdfb5cf5924.
Bjorn Andersson, Fabio Estevam, Xiaolei Wang, and Jon Hunter reported that
da56a1bfbab5 ("PCI: dwc: Wait for link up only if link is started") broke
controller probing by returning an error in case the link does not come up
during host initialisation, for example when the slot is empty.
As explained in commit 886a9c134755 ("PCI: dwc: Move link handling into
common code") and as indicated by the comment "Ignore errors, the link may
come up later" in the code, waiting for link up and ignoring errors is the
intended behaviour:
Let's standardize this to succeed as there are usecases where devices
(and the link) appear later even without hotplug. For example, a
reconfigured FPGA device.
Reverting the offending commit specifically fixes a regression on Qualcomm
platforms like the Lenovo ThinkPad X13s which no longer reach the
interconnect sync state if a slot does not have a device populated (e.g. an
optional modem).
Note that enabling asynchronous probing by default as was done for Qualcomm
platforms by commit c0e1eb441b1d ("PCI: qcom: Enable async probe by
default"), should take care of any related boot time concerns.
Finally, note that the intel-gw driver is the only driver currently not
providing a .start_link() callback and instead starts the link in its
.host_init() callback, which may avoid an additional one-second timeout
during probe by making the link-up wait conditional. If anyone cares, that
can be done in a follow-up patch with a proper motivation.
[bhelgaas: add Fabio Estevam, Xiaolei Wang, Jon Hunter reports]
Fixes: da56a1bfbab5 ("PCI: dwc: Wait for link up only if link is started")
Link: https://lore.kernel.org/r/20230706082610.26584-1-johan+linaro@kernel.org
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20230704122635.1362156-1-festevam@gmail.com/
Reported-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20230705010624.3912934-1-xiaolei.wang@windriver.com/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/6ca287a1-6c7c-7b90-9022-9e73fb82b564@nvidia.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Sajid Dalvi <sdalvi@google.com>
Cc: Ajay Agarwal <ajayagarwal@google.com>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus. As
part of that merge prepping Arm DT support 13 years ago, they "temporarily"
include each other. They also include platform_device.h and of.h. As a
result, there's a pretty much random mix of those include files used
throughout the tree. In order to detangle these headers and replace the
implicit includes with struct declarations, users need to explicitly
include the correct includes.
Link: https://lore.kernel.org/r/20230714174827.4061572-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- TI J721S2 CSI BCDMA support
Updates:
- Native HDMI support for dw edma driver
- ste dma40 updates for supporting proper SRAM handle in DT
- removal of dma device chancnt setting in drivers"
* tag 'dmaengine-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (28 commits)
dmaengine: sprd: Don't set chancnt
dmaengine: hidma: Don't set chancnt
dmaengine: plx_dma: Don't set chancnt
dmaengine: axi-dmac: Don't set chancnt
dmaengine: dw-axi-dmac: Don't set chancnt
dmaengine: qcom: bam_dma: allow omitting num-{channels,ees}
dmaengine: dw-edma: Add HDMA DebugFS support
dmaengine: dw-edma: Add support for native HDMA
dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation
dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_ops
dmaengine: ste_dma40: use proper format string for resource_size_t
dmaengine: make QCOM_HIDMA depend on HAS_IOMEM
dmaengine: ste_dma40: fix typo in enum documentation
dmaengine: ste_dma40: use correct print specfier for resource_size_t
MAINTAINERS: Add myself as the DW eDMA driver reviewer
MAINTAINERS: Add Manivannan to DW eDMA driver maintainers list
MAINTAINERS: Demote Gustavo Pimentel to DW EDMA driver reviewer
dmaengine: ti: k3-udma: Add support for J721S2 CSI BCDMA instance
dt-bindings: dma: ti: Add J721S2 BCDMA
dmaengine: ti: k3-psil-j721s2: Add PSI-L thread map for main CPSW2G
...
|
|
In dw_pcie_host_init() regardless of whether the link has been
started or not, the code waits for the link to come up. Even in
cases where start_link() is not defined the code ends up spinning
in a loop for 1 second. Since in some systems dw_pcie_host_init()
gets called during probe, this one second loop for each pcie
interface instance ends up extending the boot time.
Wait for the link up in only if the start_link() is defined.
Link: https://lore.kernel.org/r/20230412093425.3659088-1-ajayagarwal@google.com
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Sajid Dalvi <sdalvi@google.com>
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
The dw_edma_core_ops structure contains a set of the operations:
device IRQ numbers getter, CPU/PCI address translation. Based on the
functions semantics the structure name "dw_edma_plat_ops" looks more
descriptive since indeed the operations are platform-specific. The
"dw_edma_core_ops" name shall be used for a structure with the IP-core
specific set of callbacks in order to abstract out DW eDMA and DW HDMA
setups. Such structure will be added in one of the next commit in the
framework of the set of changes adding the DW HDMA device support.
Anyway the renaming was necessary to distinguish two types of
the implementation callbacks:
1. DW eDMA/hDMA IP-core specific operations: device-specific CSR
setups in one or another aspect of the DMA-engine initialization.
2. DW eDMA/hDMA platform specific operations: the DMA device
environment configs like IRQs, address translation, etc.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230520050854.73160-2-cai.huoqing@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If CDM_CHECK is enabled (by the DT "snps,enable-cdm-check" property), 'val'
is overwritten by PCIE_PL_CHK_REG_CONTROL_STATUS initialization. Commit
ec7b952f453c ("PCI: dwc: Always enable CDM check if "snps,enable-cdm-check"
exists") did not account for further usage of 'val', so we wrote improper
values to PCIE_PORT_LINK_CONTROL when the CDM check is enabled.
Move the PCIE_PORT_LINK_CONTROL update to be completely after the
PCIE_PL_CHK_REG_CONTROL_STATUS register initialization.
[bhelgaas: commit log adapted from Serge's version]
Fixes: ec7b952f453c ("PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists")
Link: https://lore.kernel.org/r/20230310123510.675685-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
Since the DW eDMA core now supports eDMA controllers embedded in locally
accessible DW PCIe Root Ports and Endpoints, register these controllers
when possible.
To do that the DW PCIe core driver needs to perform some preparations
first. First of all, it needs to find the eDMA controller CSRs base
address, whether they are accessible over the Port Logic or iATU unrolled
space. Afterwards it can try to auto-detect the eDMA controller
availability and number of read/write channels. If none are found the
procedure silently returns without error.
Secondly, the platform is supposed to provide either combined or
per-channel IRQ signals. If no valid IRQs set is found, the procedure
returns without error to be backward compatible with platforms where DW
PCIe controllers have eDMA but lack the IRQ description.
Finally, before actually probing the eDMA device we need to allocate LLP
items buffers. After that the DW eDMA can be registered. If registration is
successful, a message regarding the number of detected Read/Write eDMA
channels will be printed to the system as is done for the iATU settings.
Note: the DW PCI controller driver (either host or endpoint mode) is
currently always built-in, so if the DW eDMA core is built as a module
(CONFIG_DW_EDMA=m), eDMA controllers will not be registered even if the
dw-edma module is later loaded.
Link: https://lore.kernel.org/r/20230113171409.30470-28-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
|
|
Currently almost each platform driver uses its own resets and clocks
naming in order to get the corresponding descriptors. It makes the code
harder to maintain and comprehend especially seeing the DWC PCIe core main
resets and clocks signals set hasn't changed much for about at least one
major IP-core release. So in order to organize things around these signals
we suggest to create a generic interface for them in accordance with the
naming introduced in the DWC PCIe IP-core reference manual:
Application clocks:
- "dbi" - data bus interface clock (on some DWC PCIe platforms it's
referred as "pclk", "pcie", "sys", "ahb", "cfg", "iface",
"gio", "reg", "pcie_apb_sys");
- "mstr" - AXI-bus master interface clock (some DWC PCIe glue drivers
refer to this clock as "port", "bus", "pcie_bus",
"bus_master/master_bus/axi_m", "pcie_aclk");
- "slv" - AXI-bus slave interface clock (also called as "port", "bus",
"pcie_bus", "bus_slave/slave_bus/axi_s", "pcie_aclk",
"pcie_inbound_axi").
Core clocks:
- "pipe" - core-PCS PIPE interface clock coming from external PHY (it's
normally named by the platform drivers as just "pipe");
- "core" - primary clock of the controller (none of the platform drivers
declare such a clock but in accordance with the ref. manual
the devices may have it separately specified);
- "aux" - auxiliary PMC domain clock (it is named by some platforms as
"pcie_aux" and just "aux");
- "ref" - Generic reference clock (it is a generic clock source, which
can be used as a signal source for multiple interfaces, some
platforms call it as "ref", "general", "pcie_phy",
"pcie_phy_ref").
Application resets:
- "dbi" - Data-bus interface reset (it's CSR interface clock and is
normally called as "apb" though technically it's not APB but
DWC PCIe-specific interface);
- "mstr" - AXI-bus master reset (some platforms call it as "port", "apps",
"bus", "axi_m");
- "slv" - ABI-bus slave reset (some platforms call it as "port", "apps",
"bus", "axi_s").
Core resets:
- "non-sticky" - non-sticky CSR flags reset;
- "sticky" - sticky CSR flags reset;
- "pipe" - PIPE-interface (Core-PCS) logic reset (some platforms
call it just "pipe");
- "core" - controller primary reset (resets everything except PMC
module, some platforms refer to this signal as "soft",
"pci");
- "phy" - PCS/PHY block reset (strictly speaking it is normally
connected to the input of an external block, but the
reference manual says it must be available for the PMC
working correctly, some existing platforms call it
"pciephy", "phy", "link");
- "hot" - PMC hot reset signal (also called as "sleep");
- "pwr" - cold reset signal (can be referred as "pwr", "turnoff").
Bus reset:
- "perst" - PCIe standard signal used to reset the PCIe peripheral
devices.
As you can see each platform uses it's own naming for basically the same
set of the signals. In the framework of this commit we suggest to add a
set of the clocks and reset signals resources, corresponding names and
identifiers for each denoted entity. At current stage the platforms will
be able to use the provided infrastructure to automatically request all
these resources and manipulate with them in the Host/EP init callbacks.
Alas it isn't that easy to create a common cold/hot reset procedure due to
too many platform-specifics in the procedure, like the external flags
exposure and the delays requirement.
Link: https://lore.kernel.org/r/20221113191301.5526-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Since the iATU CSR region is now retrieved in the DW PCIe resources getter
there is no much benefits in the iATU detection procedures splitting up.
Therefore let's join the iATU unroll/viewport detection procedure with the
rest of the iATU parameters detection code. The resultant method will be
as coherent as before, while the redundant functions will be eliminated
thus producing more readable code.
Link: https://lore.kernel.org/r/20221113191301.5526-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Currently the DW PCIe Root Port and Endpoint CSR spaces are retrieved in
the separate parts of the DW PCIe core driver. It doesn't really make
sense since the both controller types have identical set of the core CSR
regions: DBI, DBI CS2 and iATU/eDMA. Thus we can simplify the DW PCIe Host
and EP initialization methods by moving the platform-specific registers
space getting and mapping into a common method. It gets to be even more
justified seeing the CSRs base address pointers are preserved in the
common DW PCIe descriptor. Note all the OF-based common DW PCIe settings
initialization will be moved to the new method too in order to have a
single function for all the generic platform properties handling in single
place.
A nice side-effect of this change is that the pcie-designware-host.c and
pcie-designware-ep.c drivers are cleaned up from all the direct dw_pcie
storage modification, which makes the DW PCIe core, Root Port and Endpoint
modules more coherent.
Link: https://lore.kernel.org/r/20221113191301.5526-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Since in addition to the already available iATU unrolled mapping we are
about to add a few more DW PCIe platform-specific capabilities (CDM-check
and generic clocks/resets resources) let's add a generic interface to set
and get the flags indicating their availability. The new interface shall
improve maintainability of the platform-specific code.
Link: https://lore.kernel.org/r/20221113191301.5526-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
In accordance with the generic PCIe Root Port DT-bindings the "dma-ranges"
property has the same format as the "ranges" property. The only difference
is in their semantics. The "dma-ranges" property describes the PCIe-to-CPU
memory mapping in opposite to the CPU-to-PCIe mapping of the "ranges"
property. Even though the DW PCIe controllers are normally equipped with
the internal Address Translation Unit which inbound and outbound tables
can be used to implement both properties semantics, it was surprising for
me to discover that the host-related part of the DW PCIe driver currently
supports the "ranges" property only while the "dma-ranges" windows are
just ignored. Having the "dma-ranges" supported in the driver would be
very handy for the platforms, that don't tolerate the 1:1 CPU-PCIe memory
mapping and require a customized PCIe memory layout. So let's fix that by
introducing the "dma-ranges" property support.
First of all we suggest to rename the dw_pcie_prog_inbound_atu() method to
dw_pcie_prog_ep_inbound_atu() and create a new version of the
dw_pcie_prog_inbound_atu() function. Thus we'll have two methods for the
RC and EP controllers respectively in the same way as it has been
developed for the outbound ATU setup methods.
Secondly aside with the memory window index and type the new
dw_pcie_prog_inbound_atu() function will accept CPU address, PCIe address
and size as its arguments. These parameters define the PCIe and CPU memory
ranges which will be used to setup the respective inbound ATU mapping. The
passed parameters need to be verified against the ATU ranges constraints
in the same way as it is done for the outbound ranges.
Finally the DMA-ranges detected for the PCIe controller need to be
converted to the inbound ATU entries during the host controller
initialization procedure. It will be done in the framework of the
dw_pcie_iatu_setup() method. Note before setting the inbound ranges up we
need to disable all the inbound ATU entries in order to prevent unexpected
PCIe TLPs translations defined by some third party software like
bootloaders.
Link: https://lore.kernel.org/r/20221113191301.5526-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Some of the platforms (like Tegra194 and Tegra234) have open slots and
not having an endpoint connected to the slot is not an error.
So, changing the macro from dev_err to dev_info to log the event.
Link: https://lore.kernel.org/r/20220913101237.4337-1-vidyas@nvidia.com
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
commit aeaa0bfe89654 ("PCI: dwc: Move N_FTS setup to common setup")
incorrectly uses pci->link_gen in deriving the index to the
n_fts[] array also introducing the issue of accessing beyond the
boundaries of array for greater than Gen-2 speeds. This change fixes
that issue.
Link: https://lore.kernel.org/r/20220926111923.22487-1-vidyas@nvidia.com
Fixes: aeaa0bfe8965 ("PCI: dwc: Move N_FTS setup to common setup")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
|
|
Make __dw_pcie_prog_outbound_atu() check the requested region base and size
against what the hardware can support. Return error if the region is not
correctly aligned or of a supported size.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The DWC PCIe RC/EP/DM IP core configuration parameters determine the number
of inbound and outbound iATU windows, alignment requirements (which is also
the minimum window size), minimum and maximum sizes. If internal ATU is
enabled, the former settings are determined by CX_ATU_MIN_REGION_SIZE; the
latter are determined by CX_ATU_MAX_REGION_SIZE.
Determine the required alignment and maximum size supported by the
controller and log it to help verify whether the requested inbound or
outbound memory mappings can be fully created.
Note 1. The extended iATU regions have been supported since DWC PCIe
v4.60a. There is no need in testing the upper limit register availability
for the older cores.
Note 2. The regions alignment is determined with using the fls() method
since the lower four bits of the ATU Limit register can be occupied with
the Circular Buffer Increment setting, which can be initialized with zeros.
Link: https://lore.kernel.org/r/20220624143947.8991-13-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Previously __dw_pcie_prog_outbound_atu() duplicated a lot of code between
the iatu_unroll_enabled version and the PCIE_ATU_VIEWPORT version:
__dw_pcie_prog_outbound_atu
if (iatu_unroll_enabled)
dw_pcie_prog_outbound_atu_unroll
dw_pcie_writel_ob_unroll(PCIE_ATU_UNR_LOWER_BASE, ...)
dw_pcie_writel_ob_unroll(PCIE_ATU_UNR_UPPER_BASE, ...)
...
return
dw_pcie_writel_dbi(PCIE_ATU_VIEWPORT, ...)
dw_pcie_writel_dbi(PCIE_ATU_LOWER_BASE, ...)
dw_pcie_writel_dbi(PCIE_ATU_UPPER_BASE, ...)
...
Unify those by pushing the unroll address computation and viewport
selection down into dw_pcie_writel_atu() so we can use the same
dw_pcie_writel_atu_ob() accessor for both paths:
__dw_pcie_prog_outbound_atu
dw_pcie_writel_atu_ob(PCIE_ATU_LOWER_BASE, ...)
dw_pcie_writel_atu
dw_pcie_select_atu # new
if (iatu_unroll_enabled)
return pci->atu_base + PCIE_ATU_UNROLL_BASE(...)
dw_pcie_writel_dbi(PCIE_ATU_VIEWPORT, ...)
return pci->atu_base
dw_pcie_write(base + reg)
dw_pcie_writel_atu_ob(PCIE_ATU_UPPER_BASE, ...)
...
In the non-unroll case, this does involve more MMIO writes to
PCIE_ATU_VIEWPORT, but it's mainly in initialization paths and the code
simplification is significant.
[bhelgaas: commit log, simplify dw_pcie_select_atu()]
Link: https://lore.kernel.org/r/20220624143947.8991-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Previously callers of dw_pcie_disable_atu() supplied enum
dw_pcie_region_type (DW_PCIE_REGION_INBOUND, DW_PCIE_REGION_OUTBOUND),
which dw_pcie_disable_atu() converted to the PCIE_ATU_REGION_DIR_IB or
PCIE_ATU_REGION_DIR_OB values needed to program the ATU registers.
Simplify the code by dropping the dw_pcie_region_type enum and passing
PCIE_ATU_REGION_DIR_IB or PCIE_ATU_REGION_DIR_OB directly.
Reorder dw_pcie_disable_atu() arguments to (dir, index) since "index"
indicates an ATU window in the regions of the corresponding direction.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Previously dw_pcie_ep_set_bar() converted the BAR PCI_BASE_ADDRESS_SPACE
bit to the internal dw_pcie_as_type enum (DW_PCIE_AS_MEM, DW_PCIE_AS_IO)
and passed it down to dw_pcie_prog_inbound_atu(), which converted the enum
to the PCIE_ATU_TYPE_MEM/PCIE_ATU_TYPE_IO values needed to program the ATU
registers.
Simplify the code by dropping the dw_pcie_as_type enum and passing
PCIE_ATU_TYPE_MEM or PCIE_ATU_TYPE_IO directly.
Reorder inbound ATU function arguments to match the outbound functions,
with address-related parameters at the end.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add macros to compare DWC IP core versions:
dw_pcie_ver_is()
dw_pcie_ver_is_ge()
dw_pcie_ver_type_is()
dw_pcie_ver_type_is_ge()
These are along the lines of DWC3_VER_IS() and dw_spi_ver_is().
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Since DWC PCIe v4.70a, the controller version and version type can be read
from the PORT_LOGIC.PCIE_VERSION_OFF and PORT_LOGIC.PCIE_VERSION_TYPE_OFF
registers respectively.
Read the version from those registers and warn if if's different from the
version we got from the device tree.
We can only read the version after platform-specific drivers have done any
DBI-related initialization, such as reference clock activation.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Save the DWC IP core version in the same format as the
PORT_LOGIC.PCIE_VERSION_OFF register, similar to what other drivers for DWC
IP do (dw_spi_hw_init(), dwc3_core_is_valid(), stmmac_hwif_init()).
[bhelgaas: trim commit log]
Link: https://lore.kernel.org/r/20220624143947.8991-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Printing just "link up" isn't very informative for PCI Express. Even if the
link is up, bus performance can degrade to slower speeds or to narrower
width than both Root Port and its partner is capable of. In that case it
would be handy to know the link specifications as early as possible.
If the link comes up, log the link speed (PCIe generation) and width.
Link: https://lore.kernel.org/r/20220624143947.8991-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
There are several places in the common DW PCIe code with incoherent local
variable usage: a variable is defined and initialized with a structure
field, but the structure pointer is dereferenced to access that field
anyway; the local variable is defined and initialized but either used just
once or not used afterwards in the main part of the subsequent method. It
mainly concerns the pcie_port.dev field. Fix that in the relevant places.
Link: https://lore.kernel.org/r/20220624143428.8334-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
While the rest of the generic DWC PCIe code uses the dedicated IO-mem
accessors, the dw_pcie_link_up() method for some unobvious reason directly
calls readl() to get PortLogic.DEBUG1 register content. Since the way the
DBI bus is accessed can be platform-specific, use dw_pcie_readl_dbi()
instead so dw_pcie_link_up() is slightly more generic.
Link: https://lore.kernel.org/r/20220624143428.8334-11-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
The unrolled version of the internal ATU has been available since the DWC
PCIe v4.80a IP core, but it may not be enabled. Per [1], if unrolled ATU
is enabled, the PCIE_ATU_VIEWPORT does not exist and reads as 0xffffffff;
while if unrolled ATU is disabled, PCIE_ATU_VIEWPORT will contain some
zeros.
Simplify dw_pcie_iatu_unroll_enabled() by checking the value of
PCIE_ATU_VIEWPORT.
[1] DesignWare Cores, PCI Express Controller, Register Desciptions,
v.4.90a, December 2016, p.855
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-10-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Add newlines to log messages that are missing them.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-9-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Add braces around single-line if-else statements when the opposite case
requires them.
Link: https://lore.kernel.org/r/20220624143428.8334-8-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
If the "snps,enable-cdm-check" property exists, we should enable the CDM
check. But previously dw_pcie_setup() could exit before doing so if the
"num-lanes" property was absent or invalid.
Move the CDM enable earlier so we do it regardless of whether "num-lanes"
is present.
[bhelgaas: commit log]
Fixes: 07f123def73e ("PCI: dwc: Add support to enable CDM register check")
Link: https://lore.kernel.org/r/20220624143428.8334-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
We program the 64-bit ATU limit address (in PCIE_ATU_LIMIT/
PCIE_ATU_UPPER_LIMIT or PCIE_ATU_UNR_LOWER_LIMIT/PCIE_ATU_UNR_UPPER_LIMIT),
but in addition, the PCIE_ATU_INCREASE_REGION_SIZE bit must be set if the
upper 32 bits of the limit address differ from the upper 32 bits of the
base address (see [1,2]).
5b4cf0f65324 ("PCI: dwc: Add upper limit address for outbound iATU") set
PCIE_ATU_INCREASE_REGION_SIZE, but only when the *size* was greater than
4GB. It did not set it when a smaller region crossed a 4GB boundary, e.g.,
[mem 0x0_f0000000-0x1_0fffffff].
Set PCIE_ATU_INCREASE_REGION_SIZE whenever PCIE_ATU_UPPER_LIMIT is
greater than PCIE_ATU_UPPER_BASE.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-36, p.175
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-37, p.176
[bhelgaas: commit log]
Fixes: 5b4cf0f65324 ("PCI: dwc: Add upper limit address for outbound iATU")
Link: https://lore.kernel.org/r/20220624143428.8334-5-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
dw_pcie_disable_atu() was introduced by f8aed6ec624f ("PCI: dwc:
designware: Add EP mode support") and supported only the viewport version
of the iATU CSRs.
DW PCIe IP cores v4.80a and newer also support unrolled iATU/eDMA space.
Callers of dw_pcie_disable_atu(), including pci_epc_ops.clear_bar(),
pci_epc_ops.unmap_addr(), and dw_pcie_setup_rc(), don't work correctly when
it is enabled.
Add dw_pcie_disable_atu() support for controllers with unrolled iATU CSRs
enabled.
[bhelgaas: commit log]
Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20220624143428.8334-3-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
On imx6 and perhaps others when pcie probes you get a:
imx6q-pcie 33800000.pcie: invalid resource
This occurs because the atu is not specified in the DT and as such it
should not be remapped.
Link: https://lore.kernel.org/r/20211101180243.23761-1-tharvey@gateworks.com
Fixes: 281f1f99cf3a ("PCI: dwc: Detect number of iATU windows")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
|
|
These symbols are used by the pci-dra7xx driver. Export them to allow
building pci-dra7xx as a module.
Link: https://lore.kernel.org/r/20210531085934.2662457-2-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
dw_pcie_ep_init() depends on the detected iATU region numbers to allocate
the in/outbound window management bitmap. It fails after 281f1f99cf3a
("PCI: dwc: Detect number of iATU windows").
Move the iATU region detection into a new function, move the detection to
the very beginning of dw_pcie_host_init() and dw_pcie_ep_init(). Also
remove it from the dw_pcie_setup(), since it's more like a software
initialization step than hardware setup.
Link: https://lore.kernel.org/r/20210125044803.4310-1-Zhiqiang.Hou@nxp.com
Link: https://lore.kernel.org/linux-pci/20210407131255.702054-1-dmitry.baryshkov@linaro.org
Link: https://lore.kernel.org/r/20210413142219.2301430-1-dmitry.baryshkov@linaro.org
Fixes: 281f1f99cf3a ("PCI: dwc: Detect number of iATU windows")
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[DB: moved dw_pcie_iatu_detect to happen after host_init callback]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org # v5.11+
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Some dwc-based device drivers, especially host-only drivers, may work well
with the default read_dbi/write_dbi/link_up implementations in
pcie-designware.c, so remove the assumption that every driver implements
them to simplify those drivers.
Link: https://lore.kernel.org/r/20210128144258.10329aa4@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
