| Age | Commit message (Collapse) | Author |
|---|
|
- Ensure Tegra194 and Tegra234 inbound ATU entries are 64KB-aligned to
match the hardware restriction (Jon Hunter)
- Remove unused struct 'tegra_pcie_soc' (Dr. David Alan Gilbert)
* pci/controller/tegra194:
PCI: tegra: Remove unused struct 'tegra_pcie_soc'
PCI: tegra194: Set EP alignment restriction for inbound ATU
|
|
- Use dev_err_probe() in dw-rockchip probe error path so the failures
aren't silent (Uwe Kleine-König)
- Sleep PCIE_T_PVPERL_MS (100ms) before deasserting PERST# (Damien Le Moal)
- Sleep PCIE_T_RRS_READY_MS (100ms) after conventional reset, before a
config access (Damien Le Moal)
- Request the PERST# GPIO with GPIOD_OUT_LOW so it matches the POR value,
which avoids a spurious PERST# assertion and fixes a Qcom modem firmware
crash and issues with WLAN controllers, e.g., RTL8822CE (Manivannan
Sadhasivam for rockchip, Niklas Cassel for dw-rockchip)
- Refactor dw-rockchip and add support for Endpoint mode for rk3568 and
rk3588 (Niklas Cassel)
* pci/controller/rockchip:
PCI: dw-rockchip: Use pci_epc_init_notify() directly
PCI: dw-rockchip: Add endpoint mode support
PCI: dw-rockchip: Refactor the driver to prepare for EP mode
PCI: dw-rockchip: Add rockchip_pcie_get_ltssm() helper
PCI: dw-rockchip: Fix weird indentation
PCI: dw-rockchip: Fix initial PERST# GPIO value
PCI: dw-rockchip: Add error messages in .probe() error paths
PCI: rockchip: Use GPIOD_OUT_LOW flag while requesting ep_gpio
PCI: rockchip-host: Wait 100ms after reset before starting configuration
PCI: rockchip-host: Fix rockchip_pcie_host_init_port() PERST# handling
|
|
- Add Synopsys DWC macros for lane skew configuration (Yoshihiro Shimoda)
- Add struct rcar_gen4_pcie_drvdata to provide for future SoCs with
different initialization requirements (Yoshihiro Shimoda)
- Add .ltssm_control() method for SoC dependencies (Yoshihiro Shimoda)
- Add r8a779g0 (R-Car V4H) support (Yoshihiro Shimoda)
* pci/controller/rcar-gen4:
PCI: rcar-gen4: Add support for R-Car V4H
PCI: rcar-gen4: Add .ltssm_control() for other SoC support
PCI: rcar-gen4: Add struct rcar_gen4_pcie_drvdata
PCI: dwc: Add PCIE_PORT_{FORCE,LANE_SKEW} macros
|
|
- Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup() to avoid
excessive warnings when the driver is confused about link state when
resuming (Marek Vasut)
* pci/controller/rcar:
PCI: rcar: Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup()
|
|
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)
- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
(HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't auto
detect this (Manivannan Sadhasivam)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
(Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if the
link is already disabled (Manivannan Sadhasivam)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
even if other drivers don't vote for it (Krishna chaitanya chundru)
- Add Operating Performance Points (OPP) to scale performance state based
on aggregate link bandwidth to improve SoC power efficiency (Krishna
chaitanya chundru)
- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
(Dan Carpenter)
- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
Carpenter)
* pci/controller/qcom:
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: qcom: Add OPP support to scale performance
PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
PCI: qcom-ep: Disable resources unconditionally during PERST# assert
PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
PCI: epf-mhi: Enable HDMA for SA8775P SoC
PCI: qcom-ep: Add HDMA support for SA8775P SoC
PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
PCI: dwc: Skip finding eDMA channels count for HDMA platforms
PCI: dwc: Refactor dw_pcie_edma_find_chip() API
PCI: qcom-ep: Add support for SA8775P SOC
dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
PCI: qcom: Use devm_clk_bulk_get_all() API
|
|
- Move PLDA XpressRICH generic DT binding properties to
plda,xpressrich3-axi-common.yaml where they can be shared across
PLDA-based drivers (Minda Chen)
- Create a drivers/pci/controller/plda/ directory for PLDA-based drivers
and move pcie-microchip-host.c there (Minda Chen)
- Move PLDA generic macros to pcie-plda.h where they can be shared across
drivers (Minda Chen)
- Extract PLDA generic structures from pcie-microchip-host.c, rename them
to be generic, and move them to pcie-plda-host.c where they can be shared
across drivers (Minda Chen)
- Add a .request_event_irq() callback for requesting device-specific
interrupts in addition to PLDA-generic interrupts (Minda Chen)
- Add DT binding and driver for the StarFive JH7110 SoC, based on PLDA IP
(Minda Chen)
* pci/controller/microchip:
PCI: starfive: Add JH7110 PCIe controller
dt-bindings: PCI: Add StarFive JH7110 PCIe controller
PCI: Add PCIE_RESET_CONFIG_DEVICE_WAIT_MS waiting time value
PCI: plda: Pass pci_host_bridge to plda_pcie_setup_iomems()
PCI: plda: Add host init/deinit and map bus functions
PCI: plda: Add event bitmap field to struct plda_pcie_rp
PCI: microchip: Move IRQ functions to pcie-plda-host.c
PCI: microchip: Add event irqchip field to host port and add PLDA irqchip
PCI: microchip: Add get_events() callback and PLDA get_event()
PCI: microchip: Add INTx and MSI event num to struct plda_event
PCI: microchip: Add request_event_irq() callback function
PCI: microchip: Add num_events field to struct plda_pcie_rp
PCI: microchip: Rename interrupt related functions
PCI: microchip: Move PLDA functions to pcie-plda-host.c
PCI: microchip: Rename PLDA functions to be generic
PCI: microchip: Move PLDA structures to plda-pcie.h
PCI: microchip: Rename PLDA structures to be generic
PCI: microchip: Add bridge_addr field to struct mc_pcie
PCI: microchip: Move PLDA IP register macros to pcie-plda.h
PCI: microchip: Move pcie-microchip-host.c to PLDA directory
dt-bindings: PCI: Add PLDA XpressRICH PCIe host common properties
# Conflicts:
# drivers/pci/pci.h
|
|
* pci/controller/loongson:
PCI: loongson: Enable MSI in LS7A Root Complex
|
|
- Make the ls-gen4 struct mobiveil_rp_ops constant (Christophe JAILLET)
* pci/controller/layerscape:
PCI: ls-gen4: Make struct mobiveil_rp_ops constant
|
|
- Enable BAR 0 only for v3.65a to avoid Completion Timeouts that
cause a 45 second boot delay on the v4.90a-based AM654x SoC (Siddharth
Vadapalli)
- Avoid a NULL pointer dereference if DT failed to provide a host bridge
memory window (Aleksandr Mishin)
* pci/controller/keystone:
PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)
PCI: keystone: Fix NULL pointer dereference in case of DT error in ks_pcie_setup_rc_app_regs()
PCI: keystone: Don't enable BAR 0 for AM654x
PCI: keystone: Relocate ks_pcie_set/clear_dbi_mode()
|
|
- Return zero, not garbage, when reading PCI_INTERRUPT_PIN from a Hyper-V
device (Wei Liu)
* pci/controller/hyperv:
PCI: hv: Return zero, not garbage, when reading PCI_INTERRUPT_PIN
|
|
- Use devm_clk_bulk_get_all_enable() to simplify clock setup (Shradha Todi)
* pci/controller/exynos:
PCI: exynos: Adapt to use bulk clock APIs
|
|
- Correct the dra7xx_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/dra7xx:
PCI: dra7xx: Fix dra7xx_pcie_cpu_addr_fixup() parameter name
|
|
- Correct the artpec6_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/artpec6:
PCI: artpec6: Fix artpec6_pcie_cpu_addr_fixup() parameter name
|
|
- Check IORESOURCE_BUS existence to avoid NULL pointer dereference
(Aleksandr Mishin)
* pci/controller/al:
PCI: al: Check IORESOURCE_BUS existence during probe
|
|
- Use msleep() in DWC core instead of usleep_range() for ~100 ms sleep
(Konrad Dybcio)
- Fix iATU slot management to avoid using the wrong slot after PERST#
assert/deassert, which could potentially cause DMA to go the wrong place
(Frank Li)
- Consolidate dw_pcie_prog_outbound_atu() arguments into a struct to ease
adding new functionality like initiating Message TLPs (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe messages (Yoshihiro Shimoda)
- Add #defines for PCIe INTx messages (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe PME_Turn_Off messages for
system suspend (Frank Li)
- Add dw_pcie_ep_linkdown() to reinitialize registers that are lost when
the link goes down (Manivannan Sadhasivam)
- Use dw_pcie_ep_linkdown() to reinitialize qcom non-sticky registers that
are lost when the link goes down (Manivannan Sadhasivam)
- Enforce DWC limitation that 64-bit BARs must start with the even numbered
BAR (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Enforce DWC specific 64-bit BAR limitation
PCI: layerscape-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: qcom-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper
PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: Add generic MSG TLP support for sending PME_Turn_Off when system suspend
PCI: Add PCIE_MSG_CODE_PME_TURN_OFF message macro
PCI: Add PCIE_MSG_CODE_ASSERT_INTx message macros
PCI: dwc: Add outbound MSG TLPs support
PCI: dwc: Consolidate args of dw_pcie_prog_outbound_atu() into a structure
PCI: dwc: Fix index 0 incorrectly being interpreted as a free ATU slot
PCI: dwc: Use msleep() in dw_pcie_wait_for_link()
|
|
- Include <linux/irqchip/chained_irq.h> in dra7xx to avoid implicitly
including it elsewhere (Andy Shevchenko)
- Remove unused <linux/of_gpio.h> from aardvark and dwc drivers (dra7xx,
meson, qcom, tegra194) (Andy Shevchenko)
- Convert kirin to use scoped for_each_available_child_of_node() to ease
future error exits (Javier Carrasco)
- Convert imx6 and kirin to use the agnostic GPIO API to simplify GPIO
setup and remove usage of the deprecated of_gpio.h API (Andy Shevchenko)
* pci/controller/gpio:
PCI: kirin: Convert to use agnostic GPIO API
PCI: kirin: Convert kirin_pcie_parse_port() to scoped iterator
PCI: imx6: Convert to use agnostic GPIO API
PCI: dwc: Remove unused of_gpio.h inclusion
PCI: aardvark: Remove unused of_gpio.h inclusion
PCI: dra7xx: Add missing chained IRQ header inclusion
|
|
- Remove unused struct pci_epf_group.type_group (Christophe JAILLET)
- Use cached epc_features instead of pci_epc_get_features() to avoid having
to check for failure (potential NULL pointer dereference) (Manivannan
Sadhasivam)
- Drop pointless local msix_capable variable in pci_epf_test_alloc_space()
(Manivannan Sadhasivam)
- Rename struct pci_epc_event_ops.core_init to .epc_init, since "core" is
no longer meaningful here (Manivannan Sadhasivam)
- Rename pci_epc_bme_notify(), pci_epf_mhi_bme(), pci_epc_bme_notify() to
spell out "bus_master_enable" instead of "bme" (Manivannan Sadhasivam)
- Factor pci_epf_test_clear_bar() and pci_epf_test_free_space() out of
pci_epf_test_unbind() so they can be reused elsewhere (Manivannan
Sadhasivam)
- Move DMA initialization to the pci_epf_mhi_epc_init() callback so
endpoint drivers do this uniformly (Manivannan Sadhasivam)
- Add endpoint testing for Link Down events (Manivannan Sadhasivam)
- Add 'epc_deinit' event so endpoints that can be reset via PERST# (qcom,
tegra194) can notify EPF drivers when this happens (Manivannan
Sadhasivam)
- Make pci_epc_class constant (Greg Kroah-Hartman)
- Fix vpci_scan_bus() error checking to print error for failure (not
success) and clean up after failure (Dan Carpenter)
- Fix epf_ntb_epc_cleanup() error handling to clean up scratchpad BARs and
clean up in mirror order of allocation (Dan Carpenter)
- Add rk3588, which requires 64KB BAR alignment, to pci_endpoint_test
(Niklas Cassel)
- Use memcpy_toio()/memcpy_fromio() for endpoint BAR tests to improve
performance (Niklas Cassel)
- Set DMA mask to 48 bits always to simplify endpoint test, since there's
there's no need to check for error or to fallback to 32 bits (Frank Li)
- Suggest using programmable Vendor/Device ID (when supported) to use
pci_endpoint_test without having to add new entries (Yoshihiro Shimoda)
- Remove unused pci_endpoint_test_bar_{readl,writel}() (Jiapeng Chong)
- Remove 'linkup' and add 'add_cfs' to the endpoint function driver 'ops'
documentation to match the code (Alexander Stein)
-
* pci/endpoint:
Documentation: PCI: pci-endpoint: Fix EPF ops list
misc: pci_endpoint_test: Remove unused pci_endpoint_test_bar_{readl,writel} functions
misc: pci_endpoint_test: Document policy about adding pci_device_id
misc: pci_endpoint_test: Refactor dma_set_mask_and_coherent() logic
misc: pci_endpoint_test: Use memcpy_toio()/memcpy_fromio() for BAR tests
misc: pci_endpoint_test: Add support for Rockchip rk3588
PCI: endpoint: Fix error handling in epf_ntb_epc_cleanup()
PCI: endpoint: Clean up error handling in vpci_scan_bus()
PCI: endpoint: Make pci_epc_class struct constant
PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers
PCI: endpoint: pci-epf-test: Handle Link Down event
PCI: endpoint: pci-epf-{mhi/test}: Move DMA initialization to EPC init callback
PCI: endpoint: pci-epf-test: Refactor pci_epf_test_unbind() function
PCI: endpoint: Rename BME to Bus Master Enable
PCI: endpoint: Rename core_init() callback in 'struct pci_epc_event_ops' to epc_init()
PCI: endpoint: pci-epf-test: Use 'msix_capable' flag directly in pci_epf_test_alloc_space()
PCI: endpoint: pci-epf-test: Make use of cached 'epc_features' in pci_epf_test_core_init()
PCI: endpoint: Remove unused field in struct pci_epf_group
|
|
The LS7A chipset can be used as part of a PCIe Root Complex with
Loongson-3C6000 and similar CPUs. In this case, DEV_LS7A_PCIE_PORT5 has a
PCI_CLASS_BRIDGE_HOST class code, and it is a Type 0 Function whose config
space provides access to Root Complex registers.
The DEV_LS7A_PCIE_PORT5 has an MSI Capability, and its MSI Enable bit must
be set before other devices below the Root Complex can use MSI. This is
not the standard PCI behavior of MSI Enable, so the normal PCI MSI code
does not set it.
Set the DEV_LS7A_PCIE_PORT5 MSI Enable bit via a quirk so other devices
below the Root Complex can use MSI.
[kwilczynski: exit early to reduce indentation; commit log]
Link: https://lore.kernel.org/linux-pci/20240612065315.2048110-1-chenhuacai@loongson.cn
Signed-off-by: Sheng Wu <wusheng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
The vmd driver creates a "domain" symlink in sysfs for each VMD bridge.
Previously this symlink was created after pci_bus_add_devices() added
devices below the VMD bridge and emitted udev events to announce them to
userspace.
This led to a race between userspace consumers of the udev events and the
kernel creation of the symlink. One such consumer is mdadm, which
assembles block devices into a RAID array, and for devices below a VMD
bridge, mdadm depends on the "domain" symlink.
If mdadm loses the race, it may be unable to assemble a RAID array, which
may cause a boot failure or other issues, with complaints like this:
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: Unable to get real path for '/sys/bus/pci/drivers/vmd/0000:c7:00.5/domain/device''
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: /dev/nvme1n1 is not attached to Intel(R) RAID controller.'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: No OROM/EFI properties for /dev/nvme1n1'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: no RAID superblock on /dev/nvme1n1.'
(udev-worker)[2149]: nvme1n1: Process '/sbin/mdadm -I /dev/nvme1n1' failed with exit code 1.
This symptom prevents the OS from booting successfully.
After a NVMe disk is probed/added by the nvme driver, udevd invokes mdadm
to detect if there is a mdraid associated with this NVMe disk, and mdadm
determines if a NVMe device is connected to a particular VMD domain by
checking the "domain" symlink. For example:
Thread A Thread B Thread mdadm
vmd_enable_domain
pci_bus_add_devices
__driver_probe_device
...
work_on_cpu
schedule_work_on
: wakeup Thread B
nvme_probe
: wakeup scan_work
to scan nvme disk
and add nvme disk
then wakeup udevd
: udevd executes
mdadm command
flush_work main
: wait for nvme_probe done ...
__driver_probe_device find_driver_devices
: probe next nvme device : 1) Detect domain symlink
... 2) Find domain symlink
... from vmd sysfs
... 3) Domain symlink not
... created yet; failed
sysfs_create_link
: create domain symlink
Create the VMD "domain" symlink before invoking pci_bus_add_devices() to
avoid this race.
Suggested-by: Adrian Huang <ahuang12@lenovo.com>
Link: https://lore.kernel.org/linux-pci/20240605124844.24293-1-sjiwei@163.com
Signed-off-by: Jiwei Sun <sunjw10@lenovo.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
|
|
Smatch complains that "ret" could be uninitialized if "pcie->icc_mem" is
NULL and "pm_suspend_target_state == PM_SUSPEND_MEM".
Silence this warning by initializing ret to zero.
Fixes: 78b5f6f8855e ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240708180539.1447307-4-dan.carpenter@linaro.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Only call dev_pm_opp_put() if dev_pm_opp_find_freq_exact() succeeds;
otherwise it leads to an error pointer dereference.
Fixes: 78b5f6f8855e ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240708180539.1447307-3-dan.carpenter@linaro.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Return a negative error code if dev_pm_opp_find_freq_floor() fails;
don't return success.
Fixes: 78b5f6f8855e ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240708180539.1447307-2-dan.carpenter@linaro.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
A previous commit ("PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper")
removed the dw_pcie_ep_init_notify() wrapper and changed the DWC glue
drivers to instead use pci_epc_init_notify() directly.
The endpoint support for the dw-rockchip had not been merged at that point
in time, so the previous commit wrapper") did not update dw-rockchip.
Do the same change for dw-rockchip, so that the driver will not try
to use a function that has now been removed.
Link: https://lore.kernel.org/linux-pci/20240622132024.2927799-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The PCIe controller in rk3568 and rk3588 can operate in endpoint mode.
This endpoint mode support heavily leverages the existing code in
pcie-designware-ep.c.
Add support for endpoint mode to the existing pcie-dw-rockchip glue
driver.
[kwilczynski: squash with patch adding the PCI_ENDPOINT dependency]
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-10-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Refactor the driver to prepare for EP mode.
Add of-match data to the existing compatible, and explicitly define it as
DW_PCIE_RC_TYPE. This way, we will be able to add EP mode in a follow-up
commit in a much less intrusive way, which makes the follow-up commit much
easier to review.
No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-9-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add a rockchip_pcie_ltssm() helper function that reads the LTSSM status.
This helper will be used in additional places in follow-up commits.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-8-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Fix the indentation of rockchip_pcie_{readl,writel}_apb() parameters to
match the opening parenthesis.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-7-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df4e ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
|
|
Drivers that silently fail to probe provide a bad user experience and
make it unnecessarily hard to debug such a failure.
Fix it by using dev_err_probe() instead of a plain return.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240227141256.413055-2-ukleinek@debian.org
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
|
|
PCIe r6.0, sec 6.6.1, states that the host should wait for at least 100
msec from the end of a conventional reset (PERST# is de-asserted) before
sending a configuration request to ensure that the device is able to
respond with a "Request Retry Status" completion.
Add the PCIE_T_RRS_READY_MS macro to define this wait time and modify
rockchip_pcie_host_init_port() to add this 100ms sleep after deasserting
PERST# using the ep_gpio GPIO.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-3-dlemoal@kernel.org
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
PCIe CEM r5.1, sec 2.9.2, mandates that the PERST# signal must remain
asserted for at least 100 usec (Tperst-clk) after the PCIe reference clock
becomes stable (if a reference clock is supplied), and for at least 100
msec after the power is stable (Tpvperl, defined by the macro
PCIE_T_PVPERL_MS).
Modify rockchip_pcie_host_init_port() to satisfy these constraints by
adding a sleep period before deasserting PERST# using the ep_gpio GPIO.
Since Tperst-clk is the shorter wait time, add an msleep() call for the
longer PCIE_T_PVPERL_MS milliseconds to handle both timing requirements.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
From the DWC EP databook 5.96a, section "3.5.7.1.4 General Rules for BAR
Setup (Fixed Mask or Programmable Mask Schemes Only)":
"Any pair (for example BARs 0 and 1) can be configured as one 64-bit BAR,
two 32-bit BARs, or one 32-bit BAR."
"BAR pairs cannot overlap to form a 64-bit BAR. For example, you cannot
combine BARs 1 and 2 to form a 64-bit BAR."
While this limitation does exist in some other PCI endpoint controllers,
e.g. cdns_pcie_ep_set_bar(), the limitation does not appear to be defined
in the PCIe specification itself, thus add an explicit check for this in
dw_pcie_ep_set_bar() (rather than pci_epc_set_bar()).
Link: https://lore.kernel.org/linux-pci/20240528134839.8817-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Down event
Now that dw_pcie_ep_linkdown() is available, use it. This also handles the
reinitialization of DWC non-sticky registers in addition to sending the
notification to EPF drivers.
Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-5-4395534520dc@linaro.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
event
Now that the generic dw_pcie_ep_linkdown() API is available, use it. This
also handles the reinitialization of DWC non-sticky registers in addition
to sending the notification to EPF drivers.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
suspend
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Convert loops in kirin_pcie_parse_port() to use the _scoped() version of
for_each_available_child_of_node() so the refcounts of children are
implicitly decremented when the loop is exited.
No functional change intended here, but it will make future error exits
from these loops easier.
Link: https://lore.kernel.org/linux-pci/20240609-pcie-kirin-memleak-v1-1-62b45b879576@gmail.com
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: move to GPIO series to avoid bisection hole, commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
QCOM Resource Power Manager-hardened (RPMh) is a hardware block which
maintains hardware state of a regulator by performing max aggregation of
the requests made by all of the clients.
PCIe controller can operate on different RPMh performance state of power
domain based on the speed of the link. And this performance state varies
from target to target, like some controllers support GEN3 in NOM (Nominal)
voltage corner, while some other supports GEN3 in low SVS (static voltage
scaling).
The SoC can be more power efficient if we scale the performance state
based on the aggregate PCIe link bandwidth.
Add Operating Performance Points (OPP) support to vote for RPMh state based
on the aggregate link bandwidth.
OPP can handle ICC bw voting also, so move ICC bw voting through OPP
framework if OPP entries are present.
As we are moving ICC voting as part of OPP, don't initialize ICC if OPP
is supported.
Before PCIe link is initialized vote for highest OPP in the OPP table,
so that we are voting for maximum voltage corner for the link to come up
in maximum supported speed.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-4-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
To access the host controller registers of the host controller and the
endpoint BAR/config space, the CPU-PCIe ICC (interconnect) path should
be voted otherwise it may lead to NoC (Network on chip) timeout.
We are surviving because of other driver voting for this path.
As there is less access on this path compared to PCIe to mem path
add minimum vote i.e 1KBps bandwidth always which is sufficient enough
to keep the path active and is recommended by HW team.
During S2RAM (Suspend-to-RAM), the DBI access can happen very late (while
disabling the boot CPU). So do not disable the CPU-PCIe interconnect path
during S2RAM as that may lead to NoC error.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-1-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issues exist for
the addressed memory on the host i.e., memory is not cached. But in
reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the host.
And worst case, if the memory is cached on the host, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the host is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issue exist for
the addressed memory on the endpoint i.e., memory is not cached. But
in reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the endpoint.
And worst case, if the memory is cached on the endpoint, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the endpoint is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
8775 has IP version 1.34.0 so introduce a new cfg(cfg_1_34_0) for this
platform. Assign override_no_snoop flag into struct qcom_pcie_cfg and
set it true in cfg_1_34_0 and enable cache snooping if this particular
flag is true.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
When ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/dwc/pci-exynos.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pci-host-generic.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-altera.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-altera-msi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-mediatek.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-mediatek-gen3.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/vmd.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-apple.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/controller/pcie-mt7621.o
Add the missing MODULE_DESCRIPTION() macro.
[kwilczynski: update MODULE_DESCRIPTION() text, commit log]
Link: https://lore.kernel.org/linux-pci/20240626-md-drivers-pci-controller-v2-1-94c811db7a51@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> # MT7621
|
