| Age | Commit message (Collapse) | Author |
|---|
|
As like the 'epc_init' event, that is used to signal the EPF drivers about
the EPC initialization, let's introduce 'epc_deinit' event that is used to
signal EPC deinitialization.
The EPC deinitialization applies only when any sort of fundamental reset
is supported by the endpoint controller as per the PCIe spec.
Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1.
Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support
PERST# as the fundamental reset. So the 'deinit' event will be notified to
the EPF drivers when PERST# assert happens in the above mentioned EPC
drivers.
The EPF drivers, on receiving the event through the epc_deinit() callback
should reset the EPF state machine and also cleanup any configuration that
got affected by the fundamental reset like BAR, DMA etc...
This change also warrants skipping the cleanups in unbind() if already done
in epc_deinit().
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
The intent of the code snippet is to always return 0 for both
PCI_INTERRUPT_LINE and PCI_INTERRUPT_PIN.
The check misses PCI_INTERRUPT_PIN. This patch fixes that.
This is discovered by this call in VFIO:
pci_read_config_byte(vdev->pdev, PCI_INTERRUPT_PIN, &pin);
The old code does not set *val to 0 because it misses the check for
PCI_INTERRUPT_PIN. Garbage is returned in that case.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lore.kernel.org/linux-pci/20240701202606.129606-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: stable@kernel.org
|
|
Add support for r8a779g0 (R-Car V4H).
This driver previously supported r8a779f0 (R-Car S4-8). PCIe features
of both r8a779f0 and r8a779g0 are almost all the same. For example:
- PCI Express Base Specification Revision 4.0
- Root complex mode and endpoint mode are supported
However, r8a779g0 requires specific firmware to be provided, to
initialize the PHY. Otherwise, the PCIe controller will not work.
[kwilczynski: drop the proprietary firmware conversion comment]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Sequence for controlling the LTSSM state machine is going to change
for SoCs like r8a779f0. Move the LTSSM code to a new callback
ltssm_control() and populate it for each SoCs.
This also warrants the addition of new compatibles for r8a779g0 and
r8a779h0. But since they are already part of the DT binding, it won't
make any difference.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
In order to support future SoCs such as r8a779g0 (R-Car V4H) and
r8a779h0 (R-Car V4M) that require different initialization settings,
introduce SoC specific driver data with the initial member being the
device mode.
No functional change.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
R-Car Gen4 PCIe controller needs to use the Synopsys-specific PCIe
configuration registers. So, add the macros.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
|
|
The struct mobiveil_rp_ops is not modified in this driver.
Thus, make this struct constant, which also moves data to a read-only
section decreasing object size and also improving overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
4446 336 32 4814 12ce drivers/pci/controller/mobiveil/pcie-layerscape-gen4.o
After:
=====
text data bss dec hex filename
4454 328 32 4814 12ce drivers/pci/controller/mobiveil/pcie-layerscape-gen4.o
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/189fd881cc8fd80220e74e91820e12cf3a5be114.1719260294.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
'tegra_pcie_soc' has been unused since 56e15a238d92 ("PCI: tegra: Add
Tegra194 PCIe support"). Remove it.
Link: https://lore.kernel.org/r/20240527160118.37069-1-linux@treblig.org
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Use preserve_config in place of checking for PCI_PROBE_ONLY flag to enable
support for "linux,pci-probe-only" on a per host bridge basis.
This also obviates the use of adding PCI_REASSIGN_ALL_BUS flag if
!PCI_PROBE_ONLY, as pci_assign_unassigned_root_bus_resources() takes care
of reassigning the resources that are not already claimed.
Link: https://lore.kernel.org/r/20240508174138.3630283-5-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Tegra194 and Tegra234 PCIe EP controllers have 64K alignment restriction
for the inbound ATU. Set the endpoint inbound ATU alignment to 64kB in the
Tegra194 PCIe driver.
Fixes: c57247f940e8 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Suggested-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Link: https://lore.kernel.org/linux-pci/20240508092207.337063-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Avoid large backtrace, it is sufficient to warn the user that there has
been a link problem. Either the link has failed and the system is in need
of maintenance, or the link continues to work and user has been informed.
The message from the warning can be looked up in the sources.
This makes an actual link issue less verbose.
First of all, this controller has a limitation in that the controller
driver has to assist the hardware with transition to L1 link state by
writing L1IATN to PMCTRL register, the L1 and L0 link state switching
is not fully automatic on this controller.
In case of an ASMedia ASM1062 PCIe SATA controller which does not support
ASPM, on entry to suspend or during platform pm_test, the SATA controller
enters D3hot state and the link enters L1 state. If the SATA controller
wakes up before rcar_pcie_wakeup() was called and returns to D0, the link
returns to L0 before the controller driver even started its transition to
L1 link state. At this point, the SATA controller did send an PM_ENTER_L1
DLLP to the PCIe controller and the PCIe controller received it, and the
PCIe controller did set PMSR PMEL1RX bit.
Once rcar_pcie_wakeup() is called, if the link is already back in L0 state
and PMEL1RX bit is set, the controller driver has no way to determine if
it should perform the link transition to L1 state, or treat the link as if
it is in L0 state. Currently the driver attempts to perform the transition
to L1 link state unconditionally, which in this specific case fails with a
PMSR L1FAEG poll timeout, however the link still works as it is already
back in L0 state.
Reduce this warning verbosity. In case the link is really broken, the
rcar_pcie_config_access() would fail, otherwise it will succeed and any
system with this controller and ASM1062 can suspend without generating
a backtrace.
Fixes: 84b576146294 ("PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()")
Link: https://lore.kernel.org/linux-pci/20240511235513.77301-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add StarFive JH7110 SoC PCIe controller platform driver code, JH7110
with PLDA host PCIe core.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-22-minda.chen@starfivetech.com
Co-developed-by: Kevin Xie <kevin.xie@starfivetech.com>
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mason Huo <mason.huo@starfivetech.com>
|
|
plda_pcie_setup_iomems() needs the bridge->windows list from struct
pci_host_bridge and is currently used only by pcie-microchip-host.c. This
driver uses pci_host_common_probe(), which sets a pci_host_bridge as the
drvdata, so plda_pcie_setup_iomems() used platform_get_drvdata() to find
the pci_host_bridge.
But we also want to use plda_pcie_setup_iomems() in the new pcie-starfive.c
driver, which does not use pci_host_common_probe() and will have struct
starfive_jh7110_pcie as its drvdata, so pass the pci_host_bridge directly
to plda_pcie_setup_iomems() so it doesn't need platform_get_drvdata() to
find it.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-9-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, reorder to where this is needed]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add PLDA host plda_pcie_host_init()/plda_pcie_host_deinit() and map bus
function so vendors can use it to init PLDA PCIe host core.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-19-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mason Huo <mason.huo@starfivetech.com>
|
|
PLDA DMA interrupts are not all implemented, and the non-implemented
interrupts should be masked. Add a bitmap field to mask the non-implemented
interrupts.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-18-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move IRQ related functions to common file pcie-plda-host.c
The re-use code including MSI, INTx, event interrupts and IRQ init
functions.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-17-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As the PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) shows, PLDA PCIe contains an interrupt
controller.
Microchip PolarFire PCIe event IRQs include PLDA interrupts and PolarFire
additional interrupts. The interrupt irqchip ops includes ack/mask/unmask
interrupt ops, which will write correct registers. Microchip PolarFire
PCIe additional interrupts require to write PolarFire SoC self-defined
registers. So Microchip PCIe event irqchip ops can not be re-used.
Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
To support PLDA its own event IRQ process, implements PLDA irqchip ops and
add event irqchip field to struct pcie_plda_rp.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-16-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) showed, PLDA PCIe contains an interrupt
controller.
PolarFire implements its own PCIe interrupts, additional to the regular
PCIe interrupts, due to lack of an MSI controller, so the interrupt to
event number mapping is different to the PLDA regular interrupts,
necessitating a custom get_events() implementation.
Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
plda_get_events() adds interrupt register to PLDA event num mapping codes.
All the PLDA interrupts can be seen in new added graph.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-15-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The INTx and MSI interrupt event num is different across platforms, so
add two event num fields in struct plda_event.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-14-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As the PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) shows, the PLDA IP contains an interrupt
controller. Microchip PolarFire add some interrupts based on PLDA interrupt
controller.
The Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
Both event_cause[] and mc_event_handler() contain additional interrupt
symbol names; these can not be re-used. Add a new plda_event_handler()
function, which implements PLDA interrupt defalt handler, and add a
request_event_irq() callback function for Microchip PolarFire additional
interrupts.
[kwilczynski, bhelgaas: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-13-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The number of events is different across platforms. In order to share
interrupt processing code, add a variable that defines the number of
events so that it can be set per-platform instead of hardcoding it.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-12-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Rename mc_* to plda_* for IRQ functions and related IRQ domain ops data
instances.
MSI, INTx interrupt code and IRQ init code can all be re-used.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-11-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Move plda_pcie_setup_window() and plda_pcie_setup_iomems() to
pcie-plda-host.c so they can be shared by all PLDA-based drivers.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-10-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Rename mc_pcie_setup_window() to plda_pcie_setup_window() and
mc_pcie_setup_windows() to plda_pcie_setup_iomems() so they can be shared
by all PLDA-based drivers.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-8-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Move the PLDA generic data structures to a header file so they can be
re-used by all PLDA-based drivers.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-7-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Rename struct mc_msi to plda_msi and move most of struct mc_pcie to a new
struct plda_pcie_rp so they can be shared by all PLDA-based drivers.
The axi_base_addr field remains in struct mc_pcie since it's
Microchip-specific data.
The event interrupt code is still using struct mc_pcie because the event
interrupt code can not be re-used.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-6-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Bridge address base is common PLDA field, add this to struct mc_pcie first.
INTx and MSI interrupt code will be changed to common code, so get the
bridge base address from port->bridge_addr instead of axi_base_addr.
The axi_base_addr is Microchip-specific data.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-5-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Move PLDA PCIe host controller IP registers macros to pcie-plda.h,
including bridge registers and PLDA IRQ event number.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-4-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Since Microchip PolarFire PCIe host is PLDA XpressRich IP, move to PLDA
directory. Prepare for refactoring the codes.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-3-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
|
|
ks_pcie_setup_rc_app_regs()
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd26 ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
After 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Relocate ks_pcie_set_dbi_mode() and ks_pcie_clear_dbi_mode() to avoid
forward declaration in a subsequent patch. No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-2-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Driver is using chained_irq_*() APIs, add the respective inclusion.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
There is no need to hardcode the clock info in the driver as driver can
rely on the devicetree to supply the clocks required for the functioning
of the peripheral.
Thus, remove the static clock info and obtain the platform supplied
clocks. All the clocks supplied are obtained and enabled using the
devm_clk_bulk_get_all_enable() API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240220084046.23786-3-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the dra7xx_pcie_cpu_addr_fixup() function parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-3-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the artpec6_pcie_cpu_addr_fixup() parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-4-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
If IORESOURCE_BUS is not provided in Device Tree it will be fabricated in
of_pci_parse_bus_range(), so NULL pointer dereference should not happen
here.
But that's hard to verify, so check for NULL anyway.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-pci/20240503125705.46055-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
BME which stands for 'Bus Master Enable' is not defined in the PCIe base
spec even though it is commonly referred in many places (vendor docs). To
align with the spec, rename it to its expansion 'Bus Master Enable'.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: squash removal of irrelevant 'Link is enabled']
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
SA8775P SoC supports the new Hyper DMA (HDMA) DMA Engine inside the DWC IP,
so add support for it by passing the mapping format and the number of
read/write channels count.
The PCIe EP controller used on this SoC is of version 1.34.0, so a separate
config struct is introduced for the sake of enabling HDMA conditionally.
It should be noted that for the eDMA support (predecessor of HDMA), there
are no mapping format and channels count specified. That is because eDMA
supports auto detection of both parameters, whereas HDMA doesn't.
[mani: reworded commit message, added kdoc, and minor cleanups]
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-4-f04c5cdde760@linaro.org
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
|
|
Instead of maintaining a separate capability for glue drivers that cannot
support auto detection of the eDMA mapping format, pass the mapping format
directly from them.
This will simplify the code and also allow adding HDMA support that also
doesn't support auto detection of mapping format.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-3-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
In the case of Hyper DMA (HDMA) present in DWC controllers, there is no way
the drivers can auto detect the number of read/write channels as like its
predecessor embedded DMA (eDMA). So the glue drivers making use of HDMA
have to pass the channels count during probe.
To accommodate that, skip the existing auto detection of channels count
procedure for HDMA based platforms. If the channels count passed by the
glue drivers were wrong in any form, then the existing sanity check will
catch it.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-2-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
In order to add support for Hyper DMA (HDMA), refactor the existing
dw_pcie_edma_find_chip() API by moving the common code to separate
functions.
No functional change.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-1-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
|
|
Add support for SA8775P SoC to the Qualcomm PCIe Endpoint Controller
driver. Adding new compatible string as it has different set of clocks
compared to other SoCs.
Link: https://lore.kernel.org/linux-pci/1714492540-15419-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
There is no need for the device drivers to validate the clocks defined in
Devicetree. The validation should be performed by the DT schema and the
drivers should just get all the clocks from DT. Right now the driver
hardcodes the clock info and validates them against DT which is redundant.
So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
and get rid of all static clocks info from the driver. This simplifies the
driver.
Link: https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
- Return success from endpoint probe before incorrectly dropping the
reference to the BPMP (Vidya Sagar)
* pci/controller/tegra194:
PCI: tegra194: Fix probe path for Endpoint mode
|
|
- Configure endpoint BAR to be 64-bit if the PCI_BASE_ADDRESS_MEM_TYPE_64
flag is set instead of depending on the new BAR value itself (Niklas
Cassel)
- Set Subsystem Vendor ID correctly (Rick Wertenbroek)
* pci/controller/rockchip:
PCI: rockchip-ep: Remove wrong mask on subsys_vendor_id
PCI: rockchip-ep: Set a 64-bit BAR if requested
|
