| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Lee writes:
"MFD fixes for v4.19
- Fix Dialog DA9063 regulator constraints issue causing failure in
probe
- Fix OMAP Device Tree compatible strings to match DT"
* tag 'mfd-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: omap-usb-host: Fix dts probe of children
mfd: da9063: Fix DT probing with constraints
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Juergen writes:
"xen:
Two small fixes for xen drivers."
* tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: issue warning message when out of grant maptrack entries
xen/x86/vpmu: Zero struct pt_regs before calling into sample handling code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Thomas writes:
"Make the EFI arm stub device tree loader default on to unbreak
existing EFI boot loaders which do not have DTB support."
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: default EFI_ARMSTUB_DTB_LOADER to y
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Linus writes:
"Pin control fixes for v4.19:
- Two fixes for the Intel pin controllers than cause
problems on laptops."
* tag 'pinctrl-v4.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: intel: Do pin translation in other GPIO operations as well
pinctrl: cannonlake: Fix gpio base for GPP-E
|
|
Jens writes:
"Storage fixes for 4.19-rc5
- Fix for leaking kernel pointer in floppy ioctl (Andy Whitcroft)
- NVMe pull request from Christoph, and a single ANA log page fix
(Hannes)
- Regression fix for libata qd32 support, where we trigger an illegal
active command transition. This fixes a CD-ROM detection issue that
was reported, but could also trigger premature completion of the
internal tag (me)"
* tag 'for-linus-20180920' of git://git.kernel.dk/linux-block:
floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl
libata: mask swap internal and hardware tag
nvme: count all ANA groups for ANA Log page
|
|
David writes:
"drm fixes for 4.19-rc5:
- core: fix debugfs for atomic, fix the check for atomic for
non-modesetting drivers
- amdgpu: adds a new PCI id, some kfd fixes and a sdma fix
- i915: a bunch of GVT fixes.
- vc4: scaling fix
- vmwgfx: modesetting fixes and a old buffer eviction fix
- udl: framebuffer destruction fix
- sun4i: disable on R40 fix until next kernel
- pl111: NULL termination on table fix"
* tag 'drm-fixes-2018-09-21' of git://anongit.freedesktop.org/drm/drm: (21 commits)
drm/amdkfd: Fix ATS capablity was not reported correctly on some APUs
drm/amdkfd: Change the control stack MTYPE from UC to NC on GFX9
drm/amdgpu: Fix SDMA HQD destroy error on gfx_v7
drm/vmwgfx: Fix buffer object eviction
drm/vmwgfx: Don't impose STDU limits on framebuffer size
drm/vmwgfx: limit mode size for all display unit to texture_max
drm/vmwgfx: limit screen size to stdu_max during check_modeset
drm/vmwgfx: don't check for old_crtc_state enable status
drm/amdgpu: add new polaris pci id
drm: sun4i: drop second PLL from A64 HDMI PHY
drm: fix drm_drv_uses_atomic_modeset on non modesetting drivers.
drm/i915/gvt: clear ggtt entries when destroy vgpu
drm/i915/gvt: request srcu_read_lock before checking if one gfn is valid
drm/i915/gvt: Add GEN9_CLKGATE_DIS_4 to default BXT mmio handler
drm/i915/gvt: Init PHY related registers for BXT
drm/atomic: Use drm_drv_uses_atomic_modeset() for debugfs creation
drm/fb-helper: Remove set but not used variable 'connector_funcs'
drm: udl: Destroy framebuffer only if it was initialized
drm/sun4i: Remove R40 display pipeline compatibles
drm/pl111: Make sure of_device_id tables are NULL terminated
...
|
|
into drm-fixes
A few fixes for 4.19:
- Add a new polaris pci id
- KFD fixes for raven and gfx7
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920155850.5455-1-alexander.deucher@amd.com
|
|
Because CRAT_CU_FLAGS_IOMMU_PRESENT was not set in some BIOS crat, we
need to workaround this.
For future compatibility, we also overwrite the bit in capability according
to the value of needs_iommu_device.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
CWSR fails on Raven if the control stack is MTYPE_UC, which is used
for regular GART mappings. As a workaround we map it using MTYPE_NC.
The MEC firmware expects the control stack at one page offset from the
start of the MQD so it is part of the MQD allocation on GFXv9. AMDGPU
added a memory allocation flag just for this purpose.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <yong.zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A wrong register bit was examinated for checking SDMA status so it reports
false failures. This typo only appears on gfx_v7. gfx_v8 checks the correct
bit.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For some reason I thought GPIOLIB handles translation from GPIO ranges
to pinctrl pins but it turns out not to be the case. This means that
when GPIOs operations are performed for a pin controller having a custom
GPIO base such as Cannon Lake and Ice Lake incorrect pin number gets
used internally.
Fix this in the same way we did for lock/unlock IRQ operations and
translate the GPIO number to pin before using it.
Fixes: a60eac3239f0 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Reported-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull NVMe fix from Christoph.
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvme: count all ANA groups for ANA Log page
|
|
The final field of a floppy_struct is the field "name", which is a pointer
to a string in kernel memory. The kernel pointer should not be copied to
user memory. The FDGETPRM ioctl copies a floppy_struct to user memory,
including this "name" field. This pointer cannot be used by the user
and it will leak a kernel address to user-space, which will reveal the
location of kernel code and data and undermine KASLR protection.
Model this code after the compat ioctl which copies the returned data
to a previously cleared temporary structure on the stack (excluding the
name pointer) and copy out to userspace from there. As we already have
an inparam union with an appropriate member and that memory is already
cleared even for read only calls make use of that as a temporary store.
Based on an initial patch by Brian Belleville.
CVE-2018-7755
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Broke up long line.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
hen we're comparing the hardware completion mask passed in from the
driver with the internal tag pending mask, we need to account for the
fact that the internal tag is different from the hardware tag. If not,
then we can end up either prematurely completing the internal tag (since
it's not set in the hw mask), or simply flag an error:
ata2: illegal qc_active transition (100000000->00000001)
If the internal tag is set, then swap that with the hardware tag in this
case before comparing with what the hardware reports.
Fixes: 28361c403683 ("libata: add extra internal command")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201151
Cc: stable@vger.kernel.org
Reported-by: Paul Sbarra <sbarra.paul@gmail.com>
Tested-by: Paul Sbarra <sbarra.paul@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Boris writes:
"- Fixes a bug in the ->read/write_reg() implementation of the m25p80
driver
- Make sure of_node_get/put() calls are balanced in the partition
parsing code
- Fix a race in the denali NAND controller driver
- Fix false positive WARN_ON() in the marvell NAND controller driver"
* tag 'mtd/fixes-for-4.19-rc5' of git://git.infradead.org/linux-mtd:
mtd: devices: m25p80: Make sure the buffer passed in op is DMA-able
mtd: partitions: fix unbalanced of_node_get/put()
mtd: rawnand: denali: fix a race condition when DMA is kicked
mtd: rawnand: marvell: prevent harmless warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Takashi writes:
"sound fixes for 4.19-rc5
here comes a collection of various fixes, mostly for stable-tree
or regression fixes.
Two relatively high LOCs are about the (rather simple) conversion of
uapi integer types in topology API, and a regression fix about HDMI
hotplug notification on AMD HD-audio. The rest are all small
individual fixes like ASoC Intel Skylake race condition, minor
uninitialized page leak in emu10k1 ioctl, Firewire audio error paths,
and so on."
* tag 'sound-4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (33 commits)
ALSA: fireworks: fix memory leak of response buffer at error path
ALSA: oxfw: fix memory leak of discovered stream formats at error path
ALSA: oxfw: fix memory leak for model-dependent data at error path
ALSA: bebob: fix memory leak for M-Audio FW1814 and ProjectMix I/O at error path
ALSA: hda - Enable runtime PM only for discrete GPU
ALSA: oxfw: fix memory leak of private data
ALSA: firewire-tascam: fix memory leak of private data
ALSA: firewire-digi00x: fix memory leak of private data
sound: don't call skl_init_chip() to reset intel skl soc
sound: enable interrupt after dma buffer initialization
Revert "ASoC: Intel: Skylake: Acquire irq after RIRB allocation"
ALSA: emu10k1: fix possible info leak to userspace on SNDRV_EMU10K1_IOCTL_INFO
ASoC: cs4265: fix MMTLR Data switch control
ASoC: AMD: Ensure reset bit is cleared before configuring
ALSA: fireface: fix memory leak in ff400_switch_fetching_mode()
ALSA: bebob: use address returned by kmalloc() instead of kernel stack for streaming DMA mapping
ASoC: rsnd: don't fallback to PIO mode when -EPROBE_DEFER
ASoC: rsnd: adg: care clock-frequency size
ASoC: uniphier: change status to orphan
ASoC: rsnd: fixup not to call clk_get/set under non-atomic
...
|
|
Commit 19be55701071 ("drm/ttm: add operation ctx to ttm_bo_validate v2")
introduced a regression where the vmwgfx driver refused to evict a
buffer that was still busy instead of waiting for it to become idle.
Fix this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
If framebuffers are larger, we create bounce surfaces that are within
STDU limits.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
For all display units, limit mode size exposed to texture_max_width/
height as this is the maximum framebuffer size that virtual device can
create.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
For STDU individual screen target size is limited by
SVGA_REG_SCREENTARGET_MAX_WIDTH/HEIGHT registers so add that limit
during atomic check_modeset.
An additional limit is placed in the update_layout ioctl to avoid
requesting layouts that current user-space typically can't support.
Also modified the comments to reflect current limitation on topology.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
During atomic check to prepare the new topology no need to check if
old_crtc_state was enabled or not. This will cause atomic_check to fail
because due to connector routing a crtc can be in atomic_state even if
there was no change to enable status.
Detected this issue with igt run.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Add new pci id.
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Only fixes coming from gvt containing "Two more BXT fixes from Colin,
one srcu locking fix and one fix for GGTT clear when destroy vGPU."
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180919151915.GA6309@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v4.19-rc5:
- Fix crash in vgem in drm_drv_uses_atomic_modeset.
- Allow atomic drivers that don't set DRIVER_ATOMIC to create debugfs entries.
- Fix compiler warning for unused connector_funcs.
- Fix null pointer deref on UDL unplug.
- Disable DRM support for sun4i's R40 for now.
(Not all patches went in for v4.19, so it has to wait a cycle.)
- NULL-terminate the of_device_id table in pl111.
- Make sure vc4 NV12 planar format works when displaying an unscaled fb.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/dda393bb-f13f-8d36-711b-cacfc578e5a3@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Guenter writes:
"Various bug fixes for nct6775 driver"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
James writes:
"SCSI fixes on 20180919
A couple of small but important fixes, one affecting big endian and
the other fixing a BUG_ON in scatterlist processing.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>"
|
|
When a driver domain (e.g. dom0) is running out of maptrack entries it
can't map any more foreign domain pages. Instead of silently stalling
the affected domUs issue a rate limited warning in this case in order
to make it easier to detect that situation.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
The A64 HDMI PHY seems to be not able to use the second video PLL as
clock parent in experiments.
Drop the support for the second PLL from A64 HDMI PHY driver.
Fixes: b46e2c9f5f64 ("drm/sun4i: Add support for A64 HDMI PHY")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180916043409.62374-2-icenowy@aosc.io
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Crypto stuff from Herbert:
"This push fixes a potential boot hang in ccp and an incorrect
CPU capability check in aegis/morus on x86."
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/aegis,morus - Do not require OSXSAVE for SSE2
crypto: ccp - add timeout support in the SEV command
|
|
git://git.infradead.org/linux-platform-drivers-x86
Darren writes:
"platform-drivers-x86 for v4.19-2
Free allocated ACPI buffers in two drivers.
The following is an automated git shortlog grouped by driver:
alienware-wmi:
- Correct a memory leak
dell-smbios-wmi:
- Correct a memory leak"
* tag 'platform-drivers-x86-v4.19-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: alienware-wmi: Correct a memory leak
platform/x86: dell-smbios-wmi: Correct a memory leak
|
|
The gpio base for GPP-E was set incorrectly to 258 instead of 256,
preventing the touchpad working on my Tong Fang GK5CN5Z laptop.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=200787
Signed-off-by: Simon Detheridge <s@sd.ai>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
drm-intel-fixes
gvt-fixes-2018-09-18
- Fix initial DPIO PHY register state for BXT (Colin)
- BXT untracked GEN9_CLKGATE_DIS_4 warning fix (Colin)
- Fix srcu lock for GFN valid check (Weinan)
- Should clear GGTT entry value after vGPU destroy (Zhipeng)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918073349.GQ20737@zhen-hp.sh.intel.com
|
|
As documented in spi-mem.h, spi_mem_op->data.buf.{in,out} must be
DMA-able, and commit 4120f8d158ef ("mtd: spi-nor: Use the spi_mem_xx()
API") failed to follow this rule as buffers passed to
->{read,write}_reg() are usually placed on the stack.
Fix that by allocating a scratch buffer and copying the data around.
Fixes: 4120f8d158ef ("mtd: spi-nor: Use the spi_mem_xx() API")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
|
|
Dave writes:
"Various fixes, all over the place:
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
|
|
When one vgpu is destroyed, its ggtt entries are not cleared.
This patch clears ggtt entries to avoid information leak.
v2: add 'Fixes' tag (Zhenyu)
Fixes: 2707e4446688 ("drm/i915/gvt: vGPU graphics memory virtualization")
Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Fix the suspicious RCU usage issue in intel_vgpu_emulate_mmio_write.
Here need to request the srcu read lock of kvm->srcu before doing
gfn_to_memslot(). The detailed log is as below:
[ 218.710688] =============================
[ 218.710690] WARNING: suspicious RCU usage
[ 218.710693] 4.14.15-dd+ #314 Tainted: G U
[ 218.710695] -----------------------------
[ 218.710697] ./include/linux/kvm_host.h:575 suspicious rcu_dereference_check() usage!
[ 218.710699]
other info that might help us debug this:
[ 218.710702]
rcu_scheduler_active = 2, debug_locks = 1
[ 218.710704] 1 lock held by qemu-system-x86/2144:
[ 218.710706] #0: (&gvt->lock){+.+.}, at: [<ffffffff816a1eea>] intel_vgpu_emulate_mmio_write+0x5a/0x2d0
[ 218.710721]
stack backtrace:
[ 218.710724] CPU: 0 PID: 2144 Comm: qemu-system-x86 Tainted: G U 4.14.15-dd+ #314
[ 218.710727] Hardware name: Dell Inc. OptiPlex 7040/0Y7WYT, BIOS 1.1.1 10/07/2015
[ 218.710729] Call Trace:
[ 218.710734] dump_stack+0x7c/0xb3
[ 218.710739] gfn_to_memslot+0x15f/0x170
[ 218.710743] kvm_is_visible_gfn+0xa/0x30
[ 218.710746] intel_vgpu_emulate_gtt_mmio_write+0x267/0x3c0
[ 218.710751] ? __mutex_unlock_slowpath+0x3b/0x260
[ 218.710754] intel_vgpu_emulate_mmio_write+0x182/0x2d0
[ 218.710759] intel_vgpu_rw+0xba/0x170 [kvmgt]
[ 218.710763] intel_vgpu_write+0x14d/0x1a0 [kvmgt]
[ 218.710767] __vfs_write+0x23/0x130
[ 218.710770] vfs_write+0xb0/0x1b0
[ 218.710774] SyS_pwrite64+0x73/0x90
[ 218.710777] entry_SYSCALL_64_fastpath+0x25/0x9c
[ 218.710780] RIP: 0033:0x7f33e8a91da3
[ 218.710783] RSP: 002b:00007f33dddc8700 EFLAGS: 00000293
v2: add 'Fixes' tag, refine log format.(Zhenyu)
Fixes: cc753fbe1ac4 ("drm/i915/gvt: validate gfn before set shadow page")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Host prints lots of untracked MMIO at 0x4653c when creating linux guest.
"gvt: vgpu 2: untracked MMIO 0004653c len 4"
GEN9_CLKGATE_DIS_4 (0x4653c) is accessed by i915 for gmbus clockgating.
However vgpu doesn't support any clockgating powergating operations
on related mmio access trap so need add it to default handler.
GEN9_CLKGATE_DIS_4 is accessed in bxt_gmbus_clock_gating() which only
applies to GEN9_LP so doens't show the warning on other platforms.
The solution is to add it to default handler init_bxt_mmio_info().
Reviewed-by: He, Min <min.he@intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Recent patch fixed the call trace
"ERROR Port B enabled but PHY powered down? (PHY_CTL 00000000)".
but introduced another similar call trace shown as:
"ERROR Port C enabled but PHY powered down? (PHY_CTL 00000200)".
The call trace will appear when host and guest enabled different ports,
i.e. host using PORT C or neither PORT is enabled, while guest is always
using PORT B as simulated by gvt. The issue is actually covered previously
before the commit and reverals now when the commit do the right thing.
On BXT, some PHY registers are initialized by vbios, before i915 loaded.
Later i915 will re-program some, or skip some based on the implementation.
The initialized mmio for guest i915 is done by gvt, based on the snapshot
taken from host. If host and guest have different PORT enabled, some
DPIO PHY mmios that gvt initialized for guest i915 will not match the
simualted monitor for guest, which leads to guest i915 print the calltrace
when it's trying to enable PHY and PORT.
The solution is to init these DPIO PHY registers to default value, then
guest i915 will program them to reasonable value based on the default
powerwell table and enabled PORT. Together with the old patch, all similar
call trace in guest kernel on BXT can be resolved.
v2: Move PHY register init to intel_vgpu_reset_mmio (Min)
v3: Do not delete empty line in issue fix patch. (zhenyu)
Fixes: c8ab5ac30ccc ("drm/i915/gvt: Make correct handling to vreg
BXT_PHY_CTL_FAMILY")
Reviewed-by: He, Min <min.he@intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host. The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk. This method fails when the modems are forced to
USB2 mode by the modem firmware.
Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d31fd43c0f9a ("clk: x86: Do not gate clocks enabled by the
firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes
all unclaimed PMC clocks on Cherry Trail devices to be on all the time,
resulting on the device not being able to reach S0i3 when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom
driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver
has been modified to get and enable this clock (if present) the marking of
the clocks as CLK_IS_CRITICAL is no longer necessary.
This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail
devices not being able to reach S0i3 greatly decreasing their battery
drain when suspended.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some boards a platform clock is used as clock for the r8169 chip,
this commit adds support for getting and enabling this clock (assuming
it has an "ether_clk" alias set on it).
This is related to commit d31fd43c0f9a ("clk: x86: Do not gate clocks
enabled by the firmware") which is a previous attempt to fix this for some
x86 boards, but this causes all Cherry Trail SoC using boards to not reach
there lowest power states when suspending.
This commit (together with an atom-pmc-clk driver commit adding the alias)
fixes things properly by making the r8169 get the clock and enable it when
it needs it.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d31fd43c0f9a ("clk: x86: Do not gate clocks enabled by the
firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on
all the time, resulting on the device not being able to reach S0i2 or S0i3
when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk"
alias, so that the relevant ethernet drivers can try to (optionally) use
this, without needing X86 specific code / hacks, thus fixing ethernet on
these devices without breaking S0i3 support.
This commit uses clkdev_hw_create() to create the alias, mirroring the code
for the already existing "mclk" alias for pmc_plt_clk_3.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Intel SoC was prevented from entering lower idle state because
of RTL8106E's ASPM was not enabled.
So enable ASPM on RTL8106E (chip version 39).
Now the Intel SoC can enter lower idle state, power consumption and
temperature are much lower.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a small delay after setting ASPM in vendor drivers, r8101 and
r8168.
In addition, those drivers enable ASPM before ClkReq, also change that
to align with vendor driver.
I haven't seen anything bad becasue of this, but I think it's better to
keep in sync with vendor driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As pointed out by Daniel Vetter, we should be usinng
drm_drv_uses_atomic_modeset() for determining whether or not we want to
make the debugfs nodes for atomic instead of checking DRIVER_ATOMIC, as
the former isn't an accurate representation of whether or not the driver
is actually using atomic modesetting internally (even though it might
not be exposing atomic capabilities).
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180917173733.21293-1-lyude@redhat.com
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise."
* tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-fsl-dspi: fix broken DSPI_EOQ_MODE
spi: Fix double IDR allocation with DT aliases
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
|
|
Fix the following compile warning:
drivers/net/ethernet/microchip/lan743x_main.c:2964:12: warning: lan743x_pm_suspend defined but not used [-Wunused-function]
static int lan743x_pm_suspend(struct device *dev)
drivers/net/ethernet/microchip/lan743x_main.c:2987:12: warning: lan743x_pm_resume defined but not used [-Wunused-function]
static int lan743x_pm_resume(struct device *dev)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a cut/paste error and a typo which results in ATU miss violations
not being reported.
Fixes: 0977644c5005 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matching network device based on MAC address is problematic
since a non VF network device can be creted with a duplicate MAC
address causing confusion and problems. The VMBus API does provide
a serial number that is a better matching method.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Hyper-V host API for PCI provides a unique "serial number" which
can be used as basis for sysfs PCI slot table. This can be useful
for cases where userspace wants to find the PCI device based on
serial number.
When an SR-IOV NIC is added, the host sends an attach message
with serial number. The kernel doesn't use the serial number, but
it is useful when doing the same thing in a userspace driver such
as the DPDK. By having /sys/bus/pci/slots/N it provides a direct
way to find the matching PCI device.
There maybe some cases where serial number is not unique such
as when using GPU's. But the PCI slot infrastructure will handle
that.
This has a side effect which may also be useful. The common udev
network device naming policy uses the slot information (rather
than PCI address).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
