| Age | Commit message (Collapse) | Author |
|---|
|
Add MSI Claw A1M controller to xpad_device match table when in xinput mode.
Add MSI VID as XPAD_XBOX360_VENDOR.
Signed-off-by: John Edwards <uejji@uejji.net>
Reviewed-by: Derek J. Clark <derekjohn.clark@gmail.com>
Reviewed-by: Christopher Snowhill <kode54@gmail.com>
Link: https://lore.kernel.org/r/20241010232020.3292284-4-uejji@uejji.net
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two issues in the amd-pstate cpufreq driver and update the
intel_rapl power capping driver with a new processor ID.
Specifics:
- Enable ACPI CPPC in amd_pstate_register_driver() after disabling it
in amd_pstate_unregister_driver() when switching driver operation
modes (Dhananjay Ugwekar)
- Make amd-pstate use nominal performance as the maximum performance
level when boost is disabled (Mario Limonciello)
- Add ArrowLake-H to the list of processors where PL4 is supported in
the MSR part of the intel_rapl power capping driver (Srinivas
Pandruvada)"
* tag 'pm-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: intel_rapl_msr: Add PL4 support for ArrowLake-H
cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled
cpufreq/amd-pstate: Fix amd_pstate mode switch on shared memory systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix auto-detect regression in jc42 driver"
* tag 'hwmon-for-v6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
[PATCH} hwmon: (jc42) Properly detect TSE2004-compliant devices again
|
|
Pull drm fixes from Dave Airlie:
"Weekly fixes, msm and xe are the two main ones, with a bunch of
scattered fixes including a largish revert in mgag200, then amdgpu,
vmwgfx and scattering of other minor ones.
All seems pretty regular.
msm:
- Display:
- move CRTC resource assignment to atomic_check otherwise to make
consecutive calls to atomic_check() consistent
- fix rounding / sign-extension issues with pclk calculation in
case of DSC
- cleanups to drop incorrect null checks in dpu snapshots
- fix to use kvzalloc in dpu snapshot to avoid allocation issues
in heavily loaded system cases
- Fix to not program merge_3d block if dual LM is not being used
- Fix to not flush merge_3d block if its not enabled otherwise
this leads to false timeouts
- GPU:
- a7xx: add a fence wait before SMMU table update
xe:
- New workaround to Xe2 (Aradhya)
- Fix unbalanced rpm put (Matthew Auld)
- Remove fragile lock optimization (Matthew Brost)
- Fix job release, delegating it to the drm scheduler (Matthew Brost)
- Fix timestamp bit width for Xe2 (Lucas)
- Fix external BO's dma-resv usag (Matthew Brost)
- Fix returning success for timeout in wait_token (Nirmoy)
- Initialize fence to avoid it being detected as signaled (Matthew
Auld)
- Improve cache flush for BMG (Matthew Auld)
- Don't allow hflip for tile4 framebuffer on Xe2 (Juha-Pekka)
amdgpu:
- SR-IOV fix
- CS chunk handling fix
- MES fixes
- SMU13 fixes
amdkfd:
- VRAM usage reporting fix
radeon:
- Fix possible_clones handling
i915:
- Two DP bandwidth related MST fixes
ast:
- Clear EDID on unplugged connectors
host1x:
- Fix boot on Tegra186
- Set DMA parameters
mgag200:
- Revert VBLANK support
panel:
- himax-hx83192: Adjust power and gamma
qaic:
- Sgtable loop fixes
vmwgfx:
- Limit display layout allocatino size
- Handle allocation errors in connector checks
- Clean up KMS code for 2d-only setup
- Report surface-check errors correctly
- Remove NULL test around kvfree()"
* tag 'drm-fixes-2024-10-18' of https://gitlab.freedesktop.org/drm/kernel: (45 commits)
drm/ast: vga: Clear EDID if no display is connected
drm/ast: sil164: Clear EDID if no display is connected
Revert "drm/mgag200: Add vblank support"
drm/amdgpu/swsmu: default to fullscreen 3D profile for dGPUs
drm/i915/display: Don't allow tile4 framebuffer to do hflip on display20 or greater
drm/xe/bmg: improve cache flushing behaviour
drm/xe/xe_sync: initialise ufence.signalled
drm/xe/ufence: ufence can be signaled right after wait_woken
drm/xe: Use bookkeep slots for external BO's in exec IOCTL
drm/xe/query: Increase timestamp width
drm/xe: Don't free job in TDR
drm/xe: Take job list lock in xe_sched_add_pending_job
drm/xe: fix unbalanced rpm put() with declare_wedged()
drm/xe: fix unbalanced rpm put() with fence_fini()
drm/xe/xe2lpg: Extend Wa_15016589081 for xe2lpg
drm/i915/dp_mst: Don't require DSC hblank quirk for a non-DSC compatible mode
drm/i915/dp_mst: Handle error during DSC BW overhead/slice calculation
drm/msm/a6xx+: Insert a fence wait before SMMU table update
drm/msm/dpu: don't always program merge_3d block
drm/msm/dpu: Don't always set merge_3d pending flush
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/song/md into block-6.12
Pull MD fixes from Song.
* tag 'md-6.12-20241018' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md/raid10: fix null ptr dereference in raid10_size()
md: ensure child flush IO does not affect origin bio->bi_status
|
|
Merge amd-pstate driver fixes for 6.12-rc4:
- Enable ACPI CPPC in amd_pstate_register_driver() after disabling
it in amd_pstate_unregister_driver() during driver operation mode
switch (Dhananjay Ugwekar).
- Make amd-pstate use nominal performance as the maximum performance
level when boost is disabled (Mario Limonciello).
* pm-cpufreq:
cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled
cpufreq/amd-pstate: Fix amd_pstate mode switch on shared memory systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
"ARM-SMMU fixes from Will Deacon:
- Clarify warning message when failing to disable the MMU-500
prefetcher
- Fix undefined behaviour in calculation of L1 stream-table index
when 32-bit StreamIDs are implemented
- Replace a rogue comma with a semicolon
Intel VT-d fix from Lu Baolu:
- Fix incorrect pci_for_each_dma_alias() for non-PCI devices"
* tag 'iommu-fixes-v6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommu/vt-d: Fix incorrect pci_for_each_dma_alias() for non-PCI devices
iommu/arm-smmu-v3: Convert comma to semicolon
iommu/arm-smmu-v3: Fix last_sid_idx calculation for sid_bits==32
iommu/arm-smmu: Clarify MMU-500 CPRE workaround
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- Fix PCI error recovery by handling error events correctly
- Fix CCA crypto card behavior within protected execution environment
- Two KVM commits which fix virtual vs physical address handling bugs
in KVM pfault handling
- Fix return code handling in pckmo_key2protkey()
- Deactivate sclp console as late as possible so that outstanding
messages appear on the console instead of being dropped on reboot
- Convert newlines to CRLF instead of LFCR for the sclp vt220 driver,
as required by the vt220 specification
- Initialize also psw mask in perf_arch_fetch_caller_regs() to make
sure that user_mode(regs) will return false
- Update defconfigs
* tag 's390-6.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: Update defconfigs
s390: Initialize psw mask in perf_arch_fetch_caller_regs()
s390/sclp_vt220: Convert newlines to CRLF instead of LFCR
s390/sclp: Deactivate sclp after all its users
s390/pkey_pckmo: Return with success for valid protected key types
KVM: s390: Change virtual to physical address access in diag 0x258 handler
KVM: s390: gaccess: Check if guest address is in memslot
s390/ap: Fix CCA crypto card behavior within protected execution environment
s390/pci: Handle PCI error codes other than 0x3a
|
|
rts5228, rts5261, rts5264 are supported by the rtsx_pci driver, but
they are not mentioned in the Kconfig help when the code was added.
List those models in the Kconfig help accordingly.
Signed-off-by: Yo-Jung Lin (Leo) <0xff07@gmail.com>
Link: https://lore.kernel.org/r/20241017144747.15966-1-0xff07@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Thinkpad X1 Tablet Gen 3 keyboard has the same Lenovo specific quirks
as the original Thinkpad X1 Tablet keyboard.
Add the PID for the "Thinkpad X1 Tablet Gen 3 keyboard" to the hid-lenovo
driver to fix the FnLock, Mute and media buttons not working.
Suggested-by: Izhar Firdaus <izhar@fedoraproject.org>
Closes https://bugzilla.redhat.com/show_bug.cgi?id=2315395
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
The Logitech Casa Touchpad does not reliably send touch release signals
when communicating through the Logitech Bolt wireless-to-USB receiver.
Adjusting the device class to add MT_QUIRK_NOT_SEEN_MEANS_UP to make
sure that no touches become stuck, MT_QUIRK_FORCE_MULTI_INPUT is not
needed, but harmless.
Linux does not have information on which devices are connected to the
Bolt receiver, so we have to enable this for the entire device.
Signed-off-by: Kenneth Albanowski <kenalba@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Patch for Goodix 27c6:0d42 touchpads found in Inspiron 5515 laptops.
After resume from suspend, one can communicate with this device just fine.
We can read data from it or request a reset,
but for some reason the interrupt line will not go up
when new events are available.
(it can correctly respond to a reset with an interrupt tho)
The only way I found to wake this device up
is to send anything to it after ~1.5s mark,
for example a simple read request, or power mode change.
In this patch, I simply delay the resume steps with msleep,
this will cause the set_power request to happen after
the ~1.5s barrier causing the device to resume its event interrupts.
Sleep was used rather than delayed_work
to make this workaround as non-invasive as possible.
[jkosina@suse.com: shortlog update]
Signed-off-by: Bartłomiej Maryńczak <marynczakbartlomiej@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.12-rc4
Here are some new modem device ids.
Everything has been in linux-next over night with no reported issues.
* tag 'usb-serial-6.12-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN920C04 MBIM compositions
USB: serial: option: add support for Quectel EG916Q-GL
|
|
Commit 2fae6bb7be32 ("xen/privcmd: Add new syscall to get gsi from dev")
adds a weak reverse dependency to the config XEN_PRIVCMD definition, that
dependency causes xen-privcmd can't be loaded on domU, because dependent
xen-pciback isn't always be loaded successfully on domU.
To solve above problem, remove that dependency, and do not call
pcistub_get_gsi_from_sbdf() directly, instead add a hook in
drivers/xen/apci.c, xen-pciback register the real call function, then in
privcmd_ioctl_pcidev_get_gsi call that hook.
Fixes: 2fae6bb7be32 ("xen/privcmd: Add new syscall to get gsi from dev")
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Jiqian Chen <Jiqian.Chen@amd.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Message-ID: <20241012084537.1543059-1-Jiqian.Chen@amd.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
As pointed by Coverity, there is a hidden overflow condition there.
As date is signed and u8 is unsigned, doing:
date = (data[0] << 24)
With a value bigger than 07f will make all upper bits of date
0xffffffff. This can be demonstrated with this small code:
<code>
typedef int64_t time64_t;
typedef uint8_t u8;
int main(void)
{
u8 data[] = { 0xde ,0xad , 0xbe, 0xef };
time64_t date;
date = (data[0] << 24) | (data[1] << 16) | (data[2] << 8) | data[3];
printf("Invalid data = 0x%08lx\n", date);
date = ((unsigned)data[0] << 24) | (data[1] << 16) | (data[2] << 8) | data[3];
printf("Expected data = 0x%08lx\n", date);
return 0;
}
</code>
Fix it by converting the upper bit calculation to unsigned.
Fixes: cea28e7a55e7 ("media: pulse8-cec: reorganize function order")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The logic at get_edid_tag_location() returns either an offset
or an error condition. However, the error condition uses a
non-standard "-1" value. This hits a Coverity bug, as Coverity
assumes that positive values are underflow. While this is a
false positive, returning error codes as -1 is an issue.
So, instead, use -ENOENT to indicate that the tag was not found.
Fixes: 056f2821b631 ("media: cec: extron-da-hd-4k-plus: add the Extron DA HD 4K Plus CEC driver")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The loop at stb0899_search_carrier() starts with a random
value for cfr, as reported by Coverity.
Initialize it to zero, just like stb0899_dvbs_algo() to ensure
that carrier search won't bail out.
Fixes: 8bd135bab91f ("V4L/DVB (9375): Add STB0899 support")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently, adv76xx_log_status() reads some date using
io_read() which may return negative values. The current logic
doesn't check such errors, causing colorspace to be reported
on a wrong way at adv76xx_log_status(), as reported by Coverity.
If I/O error happens there, print a different message, instead
of reporting bogus messages to userspace.
Fixes: 54450f591c99 ("[media] adv7604: driver for the Analog Devices ADV7604 video decoder")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
as reported by Coverity, if reading SNR registers fail, a negative
number will be returned, causing an underflow when reading SNR
registers.
Prevent that.
Fixes: 8953db793d5b ("V4L/DVB (9178): cx24116: Add module parameter to return SNR as ESNO.")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The PLL checks are comparing 64 bit integers with 32 bit
ones, as reported by Coverity. Depending on the values of
the variables, this may underflow.
Fix it ensuring that both sides of the expression are u64.
Fixes: 852b50aeed15 ("media: On Semi AR0521 sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The current logic allows word to be less than 2. If this happens,
there will be buffer overflows, as reported by smatch. Add extra
checks to prevent it.
While here, remove an unused word = 0 assignment.
Fixes: 6c96dbbc2aa9 ("[media] s5p-jpeg: add support for 5433")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
As warned by smatch:
drivers/staging/media/av7110/av7110_ca.c:270 dvb_ca_ioctl() warn: potential spectre issue 'av7110->ci_slot' [w] (local cap)
There is a spectre-related vulnerability at the code. Fix it.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Frequency range is set from sysfs via frequency_range_store(),
being vulnerable to spectre, as reported by smatch:
drivers/media/pci/mgb4/mgb4_cmt.c:231 mgb4_cmt_set_vin_freq_range() warn: potential spectre issue 'cmt_vals_in' [r]
drivers/media/pci/mgb4/mgb4_cmt.c:238 mgb4_cmt_set_vin_freq_range() warn: possible spectre second half. 'reg_set'
Fix it.
Fixes: 0ab13674a9bd ("media: pci: mgb4: Added Digiteq Automotive MGB4 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
|
|
fepriv->auto_sub_step is unsigned. Setting it to -1 is just a
trick to avoid calling continue, as reported by Coverity.
It relies to have this code just afterwards:
if (!ready) fepriv->auto_sub_step++;
Simplify the code by simply setting it to zero and use
continue to return to the while loop.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The dvbdev contains a static variable used to store dvb minors.
The behavior of it depends if CONFIG_DVB_DYNAMIC_MINORS is set
or not. When not set, dvb_register_device() won't check for
boundaries, as it will rely that a previous call to
dvb_register_adapter() would already be enforcing it.
On a similar way, dvb_device_open() uses the assumption
that the register functions already did the needed checks.
This can be fragile if some device ends using different
calls. This also generate warnings on static check analysers
like Coverity.
So, add explicit guards to prevent potential risk of OOM issues.
Fixes: 5dd3f3071070 ("V4L/DVB (9361): Dynamic DVB minor allocation")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As reported by Coverity, the logic at tpg_precalculate_line()
blindly rescales the buffer even when scaled_witdh is equal to
zero. If this ever happens, this will cause a division by zero.
Instead, add a WARN_ON_ONCE() to trigger such cases and return
without doing any precalculation.
Fixes: 63881df94d3e ("[media] vivid: add the Test Pattern Generator")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As detected by Coverity, the error check logic at get_ctrl() is
broken: if ptr_to_user() fails to fill a control due to an error,
no errors are returned and v4l2_g_ctrl() returns success on a
failed operation, which may cause applications to fail.
Add an error check at get_ctrl() and ensure that it will
be returned to userspace without filling the control value if
get_ctrl() fails.
Fixes: 71c689dc2e73 ("media: v4l2-ctrls: split up into four source files")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- New workaround to Xe2 (Aradhya)
- Fix unbalanced rpm put (Matthew Auld)
- Remove fragile lock optimization (Matthew Brost)
- Fix job release, delegating it to the drm scheduler (Matthew Brost)
- Fix timestamp bit width for Xe2 (Lucas)
- Fix external BO's dma-resv usag (Matthew Brost)
- Fix returning success for timeout in wait_token (Nirmoy)
- Initialize fence to avoid it being detected as signaled (Matthew Auld)
- Improve cache flush for BMG (Matthew Auld)
- Don't allow hflip for tile4 framebuffer on Xe2 (Juha-Pekka)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/jkldrex5733ldxrla75b4ayvhujjhw2kccmasl5rotoufoacj4@pkvlrrv4orc7
|
|
The barrier_nospec() after the array bounds check is overkill and
painfully slow for arches which implement it.
Furthermore, most arches don't implement it, so they remain exposed to
Spectre v1 (which can affect pretty much any CPU with branch
prediction).
Instead, clamp the user pointer to a valid range so it's guaranteed to
be a valid array index even when the bounds check mispredicts.
Fixes: 8270cb10c068 ("cdrom: Fix spectre-v1 gadget")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/1d86f4d9d8fba68e5ca64cdeac2451b95a8bf872.1729202937.git.jpoimboe@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two clk driver fixes and a unit test fix:
- Terminate the of_device_id table in the Samsung exynosautov920 clk
driver so that device matching logic doesn't run off the end of the
array into other memory and break matching for any kernel with this
driver loaded
- Properly limit the max clk ID in the Rockchip clk driver
- Use clk kunit helpers in the clk tests so that memory isn't leaked
after the test concludes"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: test: Fix some memory leaks
clk: rockchip: fix finding of maximum clock ID
clk: samsung: Fix out-of-bound access of of_match_node()
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
Short summary of fixes pull:
ast:
- Clear EDID on unplugged connectors
host1x:
- Fix boot on Tegra186
- Set DMA parameters
mgag200:
- Revert VBLANK support
panel:
- himax-hx83192: Adjust power and gamma
qaic:
- Sgtable loop fixes
vmwgfx:
- Limit display layout allocatino size
- Handle allocation errors in connector checks
- Clean up KMS code for 2d-only setup
- Report surface-check errors correctly
- Remove NULL test around kvfree()
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241017115516.GA196624@linux.fritz.box
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes
- Two DP bandwidth related MST fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZxDLdML9Dwqkb1AW@jlahtine-mobl.ger.corp.intel.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.12-2024-10-16:
amdgpu:
- SR-IOV fix
- CS chunk handling fix
- MES fixes
- SMU13 fixes
amdkfd:
- VRAM usage reporting fix
radeon:
- Fix possible_clones handling
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241016200514.3520286-1-alexander.deucher@amd.com
|
|
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.12
- Fix target passthrough identifier (Nilay)
- Fix tcp locking (Hannes)
- Replace list with sbitmap for tracking RDMA rsp tags (Guixen)
- Remove unnecessary fallthrough statements (Tokunori)
- Remove ready-without-media support (Greg)
- Fix multipath partition scan deadlock (Keith)
- Fix concurrent PCI reset and remove queue mapping (Maurizio)
- Fabrics shutdown fixes (Nilay)"
* tag 'nvme-6.12-2024-10-18' of git://git.infradead.org/nvme:
nvme: use helper nvme_ctrl_state in nvme_keep_alive_finish function
nvme: make keep-alive synchronous operation
nvme-loop: flush off pending I/O while shutting down loop controller
nvme-pci: fix race condition between reset and nvme_dev_disable()
nvme-multipath: defer partition scanning
nvme: disable CC.CRIME (NVME_CC_CRIME)
nvme: delete unnecessary fallthru comment
nvmet-rdma: use sbitmap to replace rsp free list
nvme: tcp: avoid race between queue_lock lock and destroy
nvmet-passthru: clear EUID/NGUID/UUID while using loop target
block: fix blk_rq_map_integrity_sg kernel-doc
|
|
In raid10_run() if raid10_set_queue_limits() succeed, the return value
is set to zero, and if following procedures failed raid10_run() will
return zero while mddev->private is still NULL, causing null ptr
dereference in raid10_size().
Fix the problem by only overwrite the return value if
raid10_set_queue_limits() failed.
Fixes: 3d8466ba68d4 ("md/raid10: use the atomic queue limit update APIs")
Cc: stable@vger.kernel.org
Reported-and-tested-by: ValdikSS <iam@valdikss.org.ru>
Closes: https://lore.kernel.org/all/0dd96820-fe52-4841-bc58-dbf14d6bfcc8@valdikss.org.ru/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241009014914.1682037-1-yukuai1@huaweicloud.com
Signed-off-by: Song Liu <song@kernel.org>
|
|
When a flush is issued to an RAID array, a child flush IO is created and
issued for each member disk in the RAID array. Since commit b75197e86e6d
("md: Remove flush handling"), each child flush IO has been chained with
the original bio. As a result, the failure of any child IO could modify
the bi_status of the original bio, potentially impacting the upper-layer
filesystem.
Fix the issue by preventing child flush IO from altering the original
bio->bi_status as before. However, this design introduces a known
issue: in the event of a power failure, if a flush IO on a member
disk fails, the upper layers may not be informed. This issue is not easy
to fix and will not be addressed for the time being in this issue.
Fixes: b75197e86e6d ("md: Remove flush handling")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240919063048.2887579-1-linan666@huaweicloud.com
Signed-off-by: Song Liu <song@kernel.org>
|
|
We no more need acquiring ctrl->lock before accessing the
NVMe controller state and instead we can now use the helper
nvme_ctrl_state. So replace the use of ctrl->lock from
nvme_keep_alive_finish function with nvme_ctrl_state call.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The nvme keep-alive operation, which executes at a periodic interval,
could potentially sneak in while shutting down a fabric controller.
This may lead to a race between the fabric controller admin queue
destroy code path (invoked while shutting down controller) and hw/hctx
queue dispatcher called from the nvme keep-alive async request queuing
operation. This race could lead to the kernel crash shown below:
Call Trace:
autoremove_wake_function+0x0/0xbc (unreliable)
__blk_mq_sched_dispatch_requests+0x114/0x24c
blk_mq_sched_dispatch_requests+0x44/0x84
blk_mq_run_hw_queue+0x140/0x220
nvme_keep_alive_work+0xc8/0x19c [nvme_core]
process_one_work+0x200/0x4e0
worker_thread+0x340/0x504
kthread+0x138/0x140
start_kernel_thread+0x14/0x18
While shutting down fabric controller, if nvme keep-alive request sneaks
in then it would be flushed off. The nvme_keep_alive_end_io function is
then invoked to handle the end of the keep-alive operation which
decrements the admin->q_usage_counter and assuming this is the last/only
request in the admin queue then the admin->q_usage_counter becomes zero.
If that happens then blk-mq destroy queue operation (blk_mq_destroy_
queue()) which could be potentially running simultaneously on another
cpu (as this is the controller shutdown code path) would forward
progress and deletes the admin queue. So, now from this point onward
we are not supposed to access the admin queue resources. However the
issue here's that the nvme keep-alive thread running hw/hctx queue
dispatch operation hasn't yet finished its work and so it could still
potentially access the admin queue resource while the admin queue had
been already deleted and that causes the above crash.
This fix helps avoid the observed crash by implementing keep-alive as a
synchronous operation so that we decrement admin->q_usage_counter only
after keep-alive command finished its execution and returns the command
status back up to its caller (blk_execute_rq()). This would ensure that
fabric shutdown code path doesn't destroy the fabric admin queue until
keep-alive request finished execution and also keep-alive thread is not
running hw/hctx queue dispatch operation.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
While shutting down loop controller, we first quiesce the admin/IO queue,
delete the admin/IO tag-set and then at last destroy the admin/IO queue.
However it's quite possible that during the window between quiescing and
destroying of the admin/IO queue, some admin/IO request might sneak in
and if that happens then we could potentially encounter a hung task
because shutdown operation can't forward progress until any pending I/O
is flushed off.
This commit helps ensure that before destroying the admin/IO queue, we
unquiesce the admin/IO queue so that any outstanding requests, which are
added after the admin/IO queue is quiesced, are now flushed to its
completion.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
nvme_dev_disable() modifies the dev->online_queues field, therefore
nvme_pci_update_nr_queues() should avoid racing against it, otherwise
we could end up passing invalid values to blk_mq_update_nr_hw_queues().
WARNING: CPU: 39 PID: 61303 at drivers/pci/msi/api.c:347
pci_irq_get_affinity+0x187/0x210
Workqueue: nvme-reset-wq nvme_reset_work [nvme]
RIP: 0010:pci_irq_get_affinity+0x187/0x210
Call Trace:
<TASK>
? blk_mq_pci_map_queues+0x87/0x3c0
? pci_irq_get_affinity+0x187/0x210
blk_mq_pci_map_queues+0x87/0x3c0
nvme_pci_map_queues+0x189/0x460 [nvme]
blk_mq_update_nr_hw_queues+0x2a/0x40
nvme_reset_work+0x1be/0x2a0 [nvme]
Fix the bug by locking the shutdown_lock mutex before using
dev->online_queues. Give up if nvme_dev_disable() is running or if
it has been executed already.
Fixes: 949928c1c731 ("NVMe: Fix possible queue use after freed")
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"Most of the fixes this time are for platform specific drivers,
addressing issues found through build testing on freescale, ep93xx,
starfive, and npcm platforms, as as well as the ffa firmware.
The fixes for the scmi firmware driver address compatibility problems
found on broadcom machines.
There are only two devicetree fixes, addressing incorrect in
configuration on broadcom and marvell machines.
The changes to the Documentation and MAINTAINERS files are for
clarification only"
* tag 'arm-fixes-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
firmware: arm_ffa: Avoid string-fortify warning caused by memcpy()
firmware: arm_scmi: Queue in scmi layer for mailbox implementation
firmware: arm_ffa: Avoid string-fortify warning in export_uuid()
firmware: arm_scmi: Give SMC transport precedence over mailbox
firmware: arm_scmi: Fix the double free in scmi_debugfs_common_setup()
Documentation/process: maintainer-soc: clarify submitting patches
dmaengine: cirrus: check that output may be truncated
dmaengine: cirrus: ERR_CAST() ioremap error
MAINTAINERS: use the canonical soc mailing list address and mark it as L:
ARM: dts: bcm2837-rpi-cm3-io3: Fix HDMI hpd-gpio pin
arm64: dts: marvell: cn9130-sr-som: fix cp0 mdio pin numbers
soc: fsl: cpm1: qmc: Fix unused data compilation warning
soc: fsl: cpm1: qmc: Do not use IS_ERR_VALUE() on error pointers
reset: starfive: jh71x0: Fix accessing the empty member on JH7110 SoC
reset: npcm: convert comma to semicolon
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Current release - new code bugs:
- eth: mlx5: HWS, don't destroy more bwc queue locks than allocated
Previous releases - regressions:
- ipv4: give an IPv4 dev to blackhole_netdev
- udp: compute L4 checksum as usual when not segmenting the skb
- tcp/dccp: don't use timer_pending() in reqsk_queue_unlink().
- eth: mlx5e: don't call cleanup on profile rollback failure
- eth: microchip: vcap api: fix memory leaks in
vcap_api_encode_rule_test()
- eth: enetc: disable Tx BD rings after they are empty
- eth: macb: avoid 20s boot delay by skipping MDIO bus registration
for fixed-link PHY
Previous releases - always broken:
- posix-clock: fix missing timespec64 check in pc_clock_settime()
- genetlink: hold RCU in genlmsg_mcast()
- mptcp: prevent MPC handshake on port-based signal endpoints
- eth: vmxnet3: fix packet corruption in vmxnet3_xdp_xmit_frame
- eth: stmmac: dwmac-tegra: fix link bring-up sequence
- eth: bcmasp: fix potential memory leak in bcmasp_xmit()
Misc:
- add Andrew Lunn as a co-maintainer of all networking drivers"
* tag 'net-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
net/mlx5e: Don't call cleanup on profile rollback failure
net/mlx5: Unregister notifier on eswitch init failure
net/mlx5: Fix command bitmask initialization
net/mlx5: Check for invalid vector index on EQ creation
net/mlx5: HWS, use lock classes for bwc locks
net/mlx5: HWS, don't destroy more bwc queue locks than allocated
net/mlx5: HWS, fixed double free in error flow of definer layout
net/mlx5: HWS, removed wrong access to a number of rules variable
mptcp: pm: fix UaF read in mptcp_pm_nl_rm_addr_or_subflow
net: ethernet: mtk_eth_soc: fix memory corruption during fq dma init
vmxnet3: Fix packet corruption in vmxnet3_xdp_xmit_frame
net: dsa: vsc73xx: fix reception from VLAN-unaware bridges
net: ravb: Only advertise Rx/Tx timestamps if hardware supports it
net: microchip: vcap api: Fix memory leaks in vcap_api_encode_rule_test()
net: phy: mdio-bcm-unimac: Add BCM6846 support
dt-bindings: net: brcm,unimac-mdio: Add bcm6846-mdio
udp: Compute L4 checksum as usual when not segmenting the skb
genetlink: hold RCU in genlmsg_mcast()
net: dsa: mv88e6xxx: Fix the max_vid definition for the MV88E6361
tcp/dccp: Don't use timer_pending() in reqsk_queue_unlink().
...
|
|
timeout errors
fw_upload's poll_complete() is really intended for use with
asynchronous write() implementations - or at least those where the
write() loop may terminate without the kernel yet being aware of whether
or not the firmware upload has succeeded. For auto-update, write() is
only ever called once and will only return when uploading has completed,
be that by passing or failing. The core fw_upload code only calls
poll_complete() after the final call to write() has returned.
However, the poll_complete() implementation in the auto-update driver
was written to expect poll_complete() to be called from another context,
and it waits for a completion signalled from write(). Since
poll_complete() is actually called from the same context, after the
write() loop has terminated, wait_for_completion() never sees the
completion get signalled and always times out, causing programming to
always report a failing.
Since write() is full synchronous, and its return value will indicate
whether or not programming passed or failed, poll_complete() serves no
purpose and can be cut down to simply return FW_UPLOAD_ERR_NONE.
Cc: stable@vger.kernel.org
Fixes: ec5b0f1193ad4 ("firmware: microchip: add PolarFire SoC Auto Update support")
Reported-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Tested-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Ensure CONFIG_PHY_ROCKCHIP_SAMSUNG_HDPTX depends on CONFIG_COMMON_CLK to
fix the following link errors when compile testing some random kernel
configurations:
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.o: in function `rk_hdptx_phy_clk_register':
drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1031:(.text+0x470): undefined reference to `__clk_get_name'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1036:(.text+0x4ba): undefined reference to `devm_clk_hw_register'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1040:(.text+0x4d2): undefined reference to `of_clk_hw_simple_get'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1040:(.text+0x4da): undefined reference to `devm_of_clk_add_hw_provider'
Fixes: c4b09c562086 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409180305.53PXymZn-lkp@intel.com/
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240923-sam-hdptx-link-fix-v1-1-8d10d7456305@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit b64a85fb8f53 ("phy: ti: phy-j721e-wiz.c: Add usxgmii support in
wiz driver") added support for USXGMII mode. In doing so, P0_REFCLK_SEL
was set to "pcs_mac_clk_divx1_ln_0" (0x3) and P0_STANDARD_MODE was set to
LANE_MODE_GEN1, which results in a data rate of 5.15625 Gbps. However,
since the USXGMII mode can support up to 10.3125 Gbps data rate, the
aforementioned fields should be set to "pcs_mac_clk_divx0_ln_0" (0x2) and
LANE_MODE_GEN2 respectively. The signal corresponding to the USXGMII lane
of the SERDES has been measured as 5 Gbps without the change and 10 Gbps
with the change. Hence, fix the configuration accordingly to support
USXGMII up to 10G.
Fixes: b64a85fb8f53 ("phy: ti: phy-j721e-wiz.c: Add usxgmii support in wiz driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241012053937.3596885-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In order to connect the USB 2.0 PHY to its controller, we also need to
set "u0_pdrstn_split_sw_usbpipe_plugen" [1]. Some downstream U-Boot
versions did that, but upstream firmware does not, and the kernel must
not rely on such behavior anyway. Failing to set this left the USB
gadget port invisible to connected hosts behind.
Link: https://doc-en.rvspace.org/JH7110/TRM/JH7110_TRM/sys_syscon.html#sys_syscon__section_b3l_fqs_wsb [1]
Fixes: 16d3a71c20cf ("phy: starfive: Add JH7110 USB 2.0 PHY driver")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241015070444.20972-2-minda.chen@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The PCIe PHYs on x1e80100 do not a have a qref supply so stop requesting
one. This also avoids the follow warning at boot:
qcom-qmp-pcie-phy 1bfc000.phy: supply vdda-qref not found, using dummy regulator
Fixes: 9dab00ee9544 ("phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100")
Fixes: 606060ce8fd0 ("phy: qcom-qmp-pcie: Add support for X1E80100 g3x2 and g4x2 PCIE")
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241015121406.15033-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add the following Telit FN920C04 compositions:
0x10a2: MBIM + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a2 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a7: MBIM + tty (AT) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 18 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a7 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10aa: MBIM + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 15 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10aa Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add Quectel EM916Q-GL with product ID 0x6007
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=6007 Rev= 2.00
S: Manufacturer=Quectel
S: Product=EG916Q-GL
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=200mA
A: FirstIf#= 4 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=88(I) Atr=03(Int.) MxPS= 32 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MI_00 Quectel USB Diag Port
MI_01 Quectel USB NMEA Port
MI_02 Quectel USB AT Port
MI_03 Quectel USB Modem Port
MI_04 Quectel USB Net Port
Signed-off-by: Benjamin B. Frost <benjamin@geanix.com>
Reviewed-by: Lars Melin <larsm17@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.12-rc4
Fix two instances of memory leaks, one in ath10k and one in ath11k.
|
