| Age | Commit message (Collapse) | Author |
|---|
|
Use a local "struct spi_bitbang *bb" in spi_gpio_probe() for
brevity. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use a local "struct device *dev" in spi_gpio_probe() for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Spi_to_pdata() is not used anywhere in the code. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Under some circumstances the default 30 us polling limit is not optimal
and may lead to long delays because we are waiting on an interrupt.
with this patch we have the possibility to influence this policy.
So make this limit (in us) configurable via a module parameters
(but also modifyable via /sys/modules/...)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Setup gpio-cs to the correct levels during setup and also make the
gpio definitely an output GPIO.
This is transparently fixing some badly configured DTs in the process
where cs-gpio is set but the gpios are still configured with native cs.
It also makes 100% sure that the initial CS levels are as expected -
especially on systems with devices on a bus with mixed CS_HIGH/CS_LOW
settings.
Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
From personal bad experience (even as the author of the original driver)
it shows that native-cs is "somewhat" supported by the spi bus driver
when using a buggy device tree.
So make sure that the driver is warning in dmesg about this fact
that we are running in a not supported mode that may have surprizing
limitations.
Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The original driver by default defines num_chipselects as -1.
This actually allicates an array of 65535 entries in
of_spi_register_master.
There is a side-effect for buggy device trees that (contrary to
dt-binding documentation) have no cs-gpio defined.
This mode was never supported by the driver due to limitations
of native cs and additional code complexity and is explicitly
not stated to be implemented.
To keep backwards compatibility with such buggy DTs we limit
the number of chip_selects to 1, as for all practical purposes
it is only ever realistic to use a single chip select in
native cs mode without negative side-effects.
Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove dead code that never can get reached, as we limit count to
a max of 3.
Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On long running tests with a mcp2517fd can controller it showed that
on rare occations the data read shows corruptions for longer spi transfers.
Example of a 22 byte transfer:
expected (as captured on logic analyzer):
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 85 86 87 88 89 8a 8b
read by the driver:
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 88 89 8a 00 00 8b 9b
To fix this use BCM2835_AUX_SPI_STAT_RX_LVL to determine when we may
read data from the fifo reliably without any corruption.
Surprisingly the only values ever empirically read in
BCM2835_AUX_SPI_STAT_RX_LVL are 0x00, 0x10, 0x20 and 0x30.
So whenever the mask is not 0 we can read from the fifo in a safe manner.
The patch has now been tested intensively and we are no longer
able to reproduce the "RX" issue any longer.
Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Reported-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This read of the fifo is a potential candidate for a race condition
as the spi transfer is not necessarily finished and so can lead to
an early read of the fifo that still misses data.
So it has been removed.
Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sharing more code between polling and interrupt-driven mode.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Export spi_mem_default_supports_op(), so that controller drivers
can use this.
spi-mem driver already exports this using EXPORT_SYMBOL,
but not declared it in spi-mem.h.
This patch declares spi_mem_default_supports_op() in spi-mem.h and
also removes the static from the function prototype.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Improve maintainability by converting the register bit, bitmask, and
bitfield definitions from hexadecimal constants to constructs using
BIT(), GENMASK(), or "val << shift".
Suggested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit c9bfcb315104 (spi_mpc83xx: much improved driver) introduced
logic to ensure bits_per_word and speed_hz stay the same for a series
of spi_transfers with CS active, arguing that
The current driver may cause glitches on SPI CLK line since one
must disable the SPI controller before changing any HW settings.
This sounds quite reasonable. So this is a quite naive attempt at
relaxing this sanity checking to only ensure that speed_hz is
constant - in the faint hope that if we do not causes changes to the
clock-related fields of the SPMODE register (DIV16 and PM), those
glitches won't appear.
The purpose of this change is to allow automatically optimizing large
transfers to use 32 bits-per-word; taking one interrupt for every byte
is extremely slow.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use SPI device pointer in the remaining two error and warning prints in
pxa2xx_spi_transfer_one() instead of platform device of the controller
It make prints in the function uniform and more useful especially the
error print here as it can reveal the driver that has mapped the DMA
itself and attempts to transfer more than the maximum supported DMA
transfer length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pointer to a SPI device is passed to pxa2xx_spi_transfer_one() so there
is no need to access it through the current SPI message pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Tegra SPI controller supports lsb first mode. Default is MSB bit first
and on selection of SPI_LSB_FIRST through SPI mode transmission happens
with LSB bit first.
This patch adds SPI_LSB_FIRST flag to mode_bits and also configures it
on request.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes: Use packed mode for 32 bits per word transfers to increase
performance as each packet is a full 32-bit word.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The comment says that we should not allow changes (to
bits_per_word/speed_hz) while CS is active, and indeed the code below
does fsl_spi_setup_transfer() when the ->cs_change of the previous
spi_transfer was set (and for the very first transfer).
So the sanity checking is a bit too strict - we can change it to
follow the same logic as is used by the actual transfer loop.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
__spi_validate() in the generic SPI code sets ->speed_hz and
->bits_per_word to non-zero values, so this condition is always true.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds the dma support for the stm32-qspi hardware.
The memory buffer constraints (lowmem, vmalloc, kmap) are taken into
account by framework. In read mode, the memory map is preferred vs
dma (due to better throughput). If the dma transfer fails the buffer
is sent by polling.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds spi_master_put in release function
to drop the controller's refcount.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch moves the MT7621 SPI driver, which is used on some Ralink /
MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to
the source code are done in this patch.
This driver version was tested successfully on an MT7688 based platform
with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so
far).
This patch also documents the devicetree bindings for the MT7621 SPI
device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: NeilBrown <neil@brown.name>
Cc: Sankalp Negi <sankalpnegi2310@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Armando Miraglia <arma2ff0@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This checking is already done in __spi_validate_bits_per_word().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix sparse warning:
drivers/spi/atmel-quadspi.c:369:12: warning:
symbol 'atmel_qspi_get_name' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The newly added tracepoints in the spi-mxs driver cause a link
error when the driver is a loadable module:
ERROR: "__tracepoint_spi_transfer_stop" [drivers/spi/spi-mxs.ko] undefined!
ERROR: "__tracepoint_spi_transfer_start" [drivers/spi/spi-mxs.ko] undefined!
I'm not quite sure where to put the export statements, but
directly after the inclusion of the header seems as good as
any other place.
Fixes: f3fdea3af405 ("spi: mxs: add tracing to custom .transfer_one_message callback")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's useful during debug to see what DMA burst size is.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some masters may have different DMA burst size than hard coded default.
In such case respect the value given by DMA burst size provided via
platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Synopsys SSI Controller has an interface clock, but most SoCs hide
this away. However, on some SoCs you need to explicitly enable the
interface clock in order to access the registers. Therefore, add support
for an optional interface clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes: 2e541b64ee52 ("spi: spi-mem: stm32-qspi: add suspend/resume support")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Linux 5.1-rc1
|
|
There is nothing in the driver which requires OF specific header
to be included.
Remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The MPC8309 has a dedicated signal, SPISEL_BOOT, usually used as chip
select for the flash device from which the bootloader is loaded. It is
not an ordinary gpio, but is simply controlled via the SPI_CS register
in the system configuration.
To allow accessing such a spi slave, we need to teach
fsl_spi_cs_control() how to control the SPISEL_BOOT signal. To
distinguish the gpio-controlled slaves, continue to have those use
chip_select values of 0..ngpios-1, and use chip_select == ngpios for
the boot flash.
I'm not too happy with all the ifdeffery, but it seems to be necessary
for guarding the sysdev/fsl_soc.h and use of
get_immrbase() (spi-fsl-lib.c already contains similar ifdeffery).
Googling suggests that the MPC8306 is similar, with the SPI_CS
register at the same offset.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit b7bb367afa4b added support for inserting delays in between
individual words within a single SPI transaction. This makes it
accessible from userspace.
WARNING: This delay is silently ignored unless the SPI controller
implements extra support for it. This is similar to how the in-kernel
users handle the other existing property, spi_transfer->word_delay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Delete the extra space.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spi_transfer *t will be used in one transfer whatever. If t is NULL,
there has no need to try sending data, so add an error return here.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add dma mode support for LPSPI. Any frame longer than half txfifosize will
be sent by dma mode.
For now, there are some limits:
1. The maximum transfer speed in master mode depends on the slave device,
at least 40MHz(tested by spi-nor on 8qm-lpddr4-arm2 base board);
2. The maximum transfer speed in slave mode is 15MHz(imx7ulp),
22MHz(8qm/qxp). In order to reach the maximum speed which is mentioned
in datasheet, the load of connect wires between master and slave
should be less than 15pF.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the default implementation of transfer_one_msg/chipselect/setup
functions in spi core to implement cs-gpio control.
Use fsl_lpspi_prepare_message to init the cs_gpio pin.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a error info when set a speed which greater than half of per-clk of
spi module.
The minimum SCK period is 2 cycles(CCR[SCKDIV]). So the maximum transfer
speed is half of spi per-clk.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enable the runtime power management for lpspi module.
Do some adaptation work from kernel 4.9 to 4.14.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add both ipg and per clock for lpspi to support i.MX8QM/QXP boards.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A fix for a Xen bug introduced by David's series for excluding
ballooned pages in vmcores"
* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Fix mapping PG_offline pages to user space
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull device-dax updates from Dan Williams:
"New device-dax infrastructure to allow persistent memory and other
"reserved" / performance differentiated memories, to be assigned to
the core-mm as "System RAM".
Some users want to use persistent memory as additional volatile
memory. They are willing to cope with potential performance
differences, for example between DRAM and 3D Xpoint, and want to use
typical Linux memory management apis rather than a userspace memory
allocator layered over an mmap() of a dax file. The administration
model is to decide how much Persistent Memory (pmem) to use as System
RAM, create a device-dax-mode namespace of that size, and then assign
it to the core-mm. The rationale for device-dax is that it is a
generic memory-mapping driver that can be layered over any "special
purpose" memory, not just pmem. On subsequent boots udev rules can be
used to restore the memory assignment.
One implication of using pmem as RAM is that mlock() no longer keeps
data off persistent media. For this reason it is recommended to enable
NVDIMM Security (previously merged for 5.0) to encrypt pmem contents
at rest. We considered making this recommendation an actively enforced
requirement, but in the end decided to leave it as a distribution /
administrator policy to allow for emulation and test environments that
lack security capable NVDIMMs.
Summary:
- Replace the /sys/class/dax device model with /sys/bus/dax, and
include a compat driver so distributions can opt-in to the new ABI.
- Allow for an alternative driver for the device-dax address-range
- Introduce the 'kmem' driver to hotplug / assign a device-dax
address-range to the core-mm.
- Arrange for the device-dax target-node to be onlined so that the
newly added memory range can be uniquely referenced by numa apis"
NOTE! I'm not entirely happy with the whole "PMEM as RAM" model because
we currently have special - and very annoying rules in the kernel about
accessing PMEM only with the "MC safe" accessors, because machine checks
inside the regular repeat string copy functions can be fatal in some
(not described) circumstances.
And apparently the PMEM modules can cause that a lot more than regular
RAM. The argument is that this happens because PMEM doesn't necessarily
get scrubbed at boot like RAM does, but that is planned to be added for
the user space tooling.
Quoting Dan from another email:
"The exposure can be reduced in the volatile-RAM case by scanning for
and clearing errors before it is onlined as RAM. The userspace tooling
for that can be in place before v5.1-final. There's also runtime
notifications of errors via acpi_nfit_uc_error_notify() from
background scrubbers on the DIMM devices. With that mechanism the
kernel could proactively clear newly discovered poison in the volatile
case, but that would be additional development more suitable for v5.2.
I understand the concern, and the need to highlight this issue by
tapping the brakes on feature development, but I don't see PMEM as RAM
making the situation worse when the exposure is also there via DAX in
the PMEM case. Volatile-RAM is arguably a safer use case since it's
possible to repair pages where the persistent case needs active
application coordination"
* tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: "Hotplug" persistent memory for use like normal RAM
mm/resource: Let walk_system_ram_range() search child resources
mm/memory-hotplug: Allow memory resources to be children
mm/resource: Move HMM pr_debug() deeper into resource code
mm/resource: Return real error codes from walk failures
device-dax: Add a 'modalias' attribute to DAX 'bus' devices
device-dax: Add a 'target_node' attribute
device-dax: Auto-bind device after successful new_id
acpi/nfit, device-dax: Identify differentiated memory with a unique numa-node
device-dax: Add /sys/class/dax backwards compatibility
device-dax: Add support for a dax override driver
device-dax: Move resource pinning+mapping into the common driver
device-dax: Introduce bus + driver model
device-dax: Start defining a dax bus model
device-dax: Remove multi-resource infrastructure
device-dax: Kill dax_region base
device-dax: Kill dax_region ida
|
|
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
|
|
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
|
|
Pull KVM updates from Paolo Bonzini:
"ARM:
- some cleanups
- direct physical timer assignment
- cache sanitization for 32-bit guests
s390:
- interrupt cleanup
- introduction of the Guest Information Block
- preparation for processor subfunctions in cpu models
PPC:
- bug fixes and improvements, especially related to machine checks
and protection keys
x86:
- many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations
- AVIC fixes
Generic:
- memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
kvm: vmx: fix formatting of a comment
KVM: doc: Document the life cycle of a VM and its resources
MAINTAINERS: Add KVM selftests to existing KVM entry
Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
KVM: PPC: Fix compilation when KVM is not enabled
KVM: Minor cleanups for kvm_main.c
KVM: s390: add debug logging for cpu model subfunctions
KVM: s390: implement subfunction processor calls
arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
KVM: arm/arm64: Remove unused timer variable
KVM: PPC: Book3S: Improve KVM reference counting
KVM: PPC: Book3S HV: Fix build failure without IOMMU support
Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
x86: kvmguest: use TSC clocksource if invariant TSC is exposed
KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
...
|
