| Age | Commit message (Collapse) | Author |
|---|
|
I2C DesignWare may abort transfer with arbitration lost if I2C slave pulls
SDA down quickly after falling edge of SCL. Reason for this is unknown but
after trial and error it was found this can be avoided by enabling non-zero
SDA RX hold time for the receiver.
By the specification SDA RX hold time extends incoming SDA low to high
transition by n * ic_clk cycles but only when SCL is high. However it
seems to help avoid above faulty arbitration lost error.
Bits 23:16 in IC_SDA_HOLD register define the SDA RX hold time for the
receiver. Be conservative and enable 1 ic_clk cycle long hold time in
case boot firmware hasn't set it up.
Reported-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus
controller includes a SPD EEPROM protection mechanism. Once the SPD
Write Disable bit is set, only reads are allowed to slave addresses
0x50-0x57.
However the legacy implementation of I2C Block Read since the ICH5
looks like a write, and is therefore blocked by the SPD protection
mechanism. This causes the eeprom and at24 drivers to fail.
So assume that I2C Block Read is implemented as an actual read on
these chipsets. I tested it on my Q87 chipset and it seems to work
just fine.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: rebased to v4.9-rc2]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
SMBus block command uses the first byte of buffer for the data length.
The dma_buffer should be increased by 1 to avoid the overrun issue.
Reported-by: Phil Endecott <phil_gjouf_endecott@chezphil.org>
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The i2c controller used by Freescales iMX processors is the same
hardware module used on Freescales ColdFire family of processors.
We can use the existing i2c-imx driver on ColdFire family members.
Modify the configuration to allow it to be selected when compiling
for ColdFire targets.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Instantiated I2C device nodes are marked with OF_POPULATE. This was
introduced in 4f001fd30145a6. On unloading, loaded device nodes will of
course be unmarked. The problem are nodes that fail during
initialisation: If a node fails, it won't be unloaded and hence not be
unmarked.
If a I2C driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Fixes: 4f001fd30145a6 ("i2c: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[wsa: use 14-digit commit sha]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.
So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
This driver should be buildable with ARCH_HISI,
because some of other HiSilicon SoCs also use it.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Pull UBI[FS] fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- Fallout from the merge window, refactoring UBI code introduced some
issues.
- Fixes for an UBIFS readdir bug which can cause getdents() to busy
loop for ever and a bug in the UBIFS xattr code"
* tag 'upstream-4.9-rc2' of git://git.infradead.org/linux-ubifs:
ubifs: Abort readdir upon error
UBI: Fix crash in try_recover_peb()
ubi: fix swapped arguments to call to ubi_alloc_aeb
ubifs: Fix xattr_names length in exit paths
ubifs: Rename ubifs_rename2
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target-pending fixes for v4.9-rc2.
This includes:
- Fix v4.1.y+ reference leak regression with concurrent TMR
ABORT_TASK + session shutdown. (Vaibhav Tandon)
- Enable tcm_fc w/ SCF_USE_CPUID to avoid host exchange timeouts
(Hannes)
- target/user error sense handling fixes. (Andy + MNC + HCH)
- Fix iscsi-target NOP_OUT error path iscsi_cmd descriptor leak
(Varun)
- Two EXTENDED_COPY SCSI status fixes for ESX VAAI (Dinesh Israni +
Nixon Vincent)
- Revert a v4.8 residual overflow change, that breaks sg_inq with
small allocation lengths.
There are a number of folks stress testing the v4.1.y regression fix
in their environments, and more folks doing iser-target I/O stress
testing atop recent v4.x.y code.
There is also one v4.2.y+ RCU conversion regression related to
explicit NodeACL configfs changes, that is still being tracked down"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/tcm_fc: use CPU affinity for responses
target/tcm_fc: Update debugging statements to match libfc usage
target/tcm_fc: return detailed error in ft_sess_create()
target/tcm_fc: print command pointer in debug message
target: fix potential race window in target_sess_cmd_list_waiting()
Revert "target: Fix residual overflow handling in target_complete_cmd_with_length"
target: Don't override EXTENDED_COPY xcopy_pt_cmd SCSI status code
target: Make EXTENDED_COPY 0xe4 failure return COPY TARGET DEVICE NOT REACHABLE
target: Re-add missing SCF_ACK_KREF assignment in v4.1.y
iscsi-target: fix iscsi cmd leak
iscsi-target: fix spelling mistake "Unsolicitied" -> "Unsolicited"
target/user: Fix comments to not refer to data ring
target/user: Return an error if cmd data size is too large
target/user: Use sense_reason_t in tcmu_queue_cmd_ring
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Couple of hwmon fixes:
Fix a potential ERR_PTR dereference in max31790 driver, and handle
temperature readings below 0 in adm9240 driver"
* tag 'hwmon-for-linus-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max31790) potential ERR_PTR dereference
hwmon: (adm9240) handle temperature readings below 0
|
|
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Mostly irqchip driver fixes, plus a symbol export"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/irq: Export irq_set_parent()
irqchip/gic: Add missing \n to CPU IF adjustment message
irqchip/jcore: Don't show Kconfig menu item for driver
irqchip/eznps: Drop pointless static qualifier in nps400_of_init()
irqchip/gic-v3-its: Fix entry size mask for GITS_BASER
irqchip/gic-v3-its: Fix 64bit GIC{R,ITS}_TYPER accesses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Add Ard Biesheuvel as EFI co-maintainer, plus fix an ARM build bug
with older toolchains"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm: Fix absolute relocation detection for older toolchains
MAINTAINERS: Add myself as EFI maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)"
* tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Ignore the pkey system calls for now
powerpc: Fix numa topology console print
powerpc/mm: Drop dump_numa_memory_topology()
cxl: Prevent adapter reset if an active context exists
powerpc/boot: Fix boot on systems with uncompressed kernel image
powerpc/mm: Prevent unlikely crash in copro_calculate_slb()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix an issue related to system resume in the new WDAT-based
watchdog driver and a return value of a stub function in the ACPI CPPC
framework.
Specifics:
- Update the ACPI WDAT-based watchdog driver to ping the hardware
during system resume to prevent a reset from occurring after the
resume is complete (Mika Westerberg).
- Fix the return value of the pcc_mbox_request_channel() stub for
CONFIG_PCC unset (Hoan Tran)"
* tag 'acpi-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
watchdog: wdat_wdt: Ping the watchdog on resume
mailbox: PCC: Fix return value of pcc_mbox_request_channel()
|
|
* acpi-wdat:
watchdog: wdat_wdt: Ping the watchdog on resume
* acpi-cppc:
mailbox: PCC: Fix return value of pcc_mbox_request_channel()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull GIC updates from Marc Zyngier:
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five small fixes.
Some of these, like the nested spinlock overwriting saved flags and
the Kasan use after free look serious, but they seem not to have been
picked up in testing or seen in the field.
The biggest user visible issue is probably the wrong device handler
for Clariion, which means that alua doesn't bind to the array like it
should"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: Fix async error WARN_ON
scsi: zfcp: spin_lock_irqsave() is not nestable
scsi: Remove one useless stack variable
scsi: Fix use-after-free
scsi: Replace wrong device handler name for CLARiiON arrays
|
|
Pull block fixes from Jens Axboe:
"A set of fixes that missed the merge window, mostly due to me being
away around that time.
Nothing major here, a mix of nvme cleanups and fixes, and one fix for
the badblocks handling"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: use symbolic constants for CNS values
nvme: use symbolic constants for CNS values
nvme.h: add an enum for cns values
nvme.h: don't use uuid_be
nvme.h: resync with nvme-cli
nvme: Add tertiary number to NVME_VS
nvme : Add sysfs entry for NVMe CMBs when appropriate
nvme: don't schedule multiple resets
nvme: Delete created IO queues on reset
nvme: Stop probing a removed device
badblocks: fix overlapping check for clearing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"This includes:
- Fix for a Layerscape driver issue that causes a use-before-set
crash
- Maintainer update for the Synopsis prototyping device driver"
* tag 'pci-v4.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware-plat: Update author email address
PCI: layerscape: Fix drvdata usage before assignment
PCI: designware-plat: Change maintainer to Jose Abreu
|
|
Although I am leaving Synopsys, I would like to keep working with the linux
kernel community and help in what you might find useful. For that I am
sending this patch to change my contact e-mail.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The libfc stack assigns exchange IDs based on the CPU the request
was received on, so we need to send the responses via the same CPU.
Otherwise the send logic gets confuses and responses will be delayed,
causing exchange timeouts on the initiator side.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Update the debug statements to match those from libfc.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Not every failure is due to out-of-memory; the ACLs might not be
set, too. So return a detailed error code in ft_sess_create()
instead of just a NULL pointer.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When allocating a new command we should add the pointer to the
debug statements; that allows us to match this with other debug
statements for handling data.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
target_sess_cmd_list_waiting() might hit on a condition where
the kref for the command is already 0, but the destructor has
not been called yet (or is stuck in waiting for a spin lock).
Rather than leaving the command on the list we should explicitly
remove it to avoid race issues later on.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
drm-fixes
2 more patches to stabilize the new MMUv2 support.
* 'drm-etnaviv-fixes' of git://git.pengutronix.de/lst/linux:
drm/etnaviv: block 64K of address space behind each cmdstream
drm/etnaviv: ensure write caches are flushed at end of user cmdstream
|
|
ssh://people.freedesktop.org/~syeh/repos_linux into drm-fixes
vmwgfx cleanups and fixes.
* 'drm-vmwgfx-fixes' of ssh://people.freedesktop.org/~syeh/repos_linux:
drm/vmwgfx: Adjust checks for null pointers in 13 functions
drm/vmwgfx: Use memdup_user() rather than duplicating its implementation
drm/vmwgfx: Use kmalloc_array() in vmw_surface_define_ioctl()
drm/vmwgfx: Avoid validating views on view destruction
drm/vmwgfx: Limit the user-space command buffer size
drm/vmwgfx: Remove a leftover debug printout
drm/vmwgfx: Allow resource relocations on byte boundaries
drm/vmwgfx: Enable SVGA_3D_CMD_DX_TRANSFER_FROM_BUFFER command
drm/vmwgfx: Remove call to reservation_object_test_signaled_rcu before wait
drm/vmwgfx: Replace numeric parameter like 0444 with macro
|
|
into drm-fixes
One small fix for Armada, where the clock prepare/enable counts were
going awry.
* 'drm-armada-fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
drm/armada: fix clock counts
|
|
http://git.agner.ch/git/linux-drm-fsl-dcu into drm-fixes
This are some fixes which I hoped to still get into v4.9. I used to
test them here since about 2 weeks and Meng came around to test it
on the second platform making use of this IP too, so they are well
tested now.
* 'fixes-for-v4.9-rc2' of http://git.agner.ch/git/linux-drm-fsl-dcu:
drm/fsl-dcu: enable pixel clock when enabling CRTC
drm/fsl-dcu: do not transfer registers in mode_set_nofb
drm/fsl-dcu: do not transfer registers on plane init
drm/fsl-dcu: enable TCON bypass mode by default
|
|
It turns out we need to ping the watchdog hardware on resume when we
re-program it. Otherwise this causes inadvertent reset to trigger
right after the resume is complete.
Fixes: 058dfc767008 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
struct clocksource is also used by the clk notifier callback, to
unregister and re-register the clocksource with a different clock rate.
clocksource_mmio_init does not pass back a pointer to the struct used,
and the clk notifier callback assumes that the struct clocksource in
struct sun5i_timer_clksrc is valid. This results in a kernel NULL
pointer dereference when the hstimer clock is changed:
Unable to handle kernel NULL pointer dereference at virtual address 00000004
[<c03a4678>] (clocksource_unbind) from [<c03a46d4>] (clocksource_unregister+0x2c/0x44)
[<c03a46d4>] (clocksource_unregister) from [<c0a6f350>] (sun5i_rate_cb_clksrc+0x34/0x3c)
[<c0a6f350>] (sun5i_rate_cb_clksrc) from [<c035ea50>] (notifier_call_chain+0x44/0x84)
[<c035ea50>] (notifier_call_chain) from [<c035edc0>] (__srcu_notifier_call_chain+0x44/0x60)
[<c035edc0>] (__srcu_notifier_call_chain) from [<c035edf4>] (srcu_notifier_call_chain+0x18/0x20)
[<c035edf4>] (srcu_notifier_call_chain) from [<c0670174>] (__clk_notify+0x70/0x7c)
[<c0670174>] (__clk_notify) from [<c06702c0>] (clk_propagate_rate_change+0xa4/0xc4)
[<c06702c0>] (clk_propagate_rate_change) from [<c0670288>] (clk_propagate_rate_change+0x6c/0xc4)
Revert the commit for now. clocksource_mmio_init can be made to pass back
a pointer, but the code churn and usage of an inner struct might not be
worth it.
Fixes: 157dfadef832 ("clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init")
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: linux-sunxi@googlegroups.com
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20161018054918.26855-1-wens@csie.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
At the hardware level, the J-Core PIT is integrated with the interrupt
controller, but it is represented as its own device and has an
independent programming interface. It provides a 12-bit countdown
timer, which is not presently used, and a periodic timer. The interval
length for the latter is programmable via a 32-bit throttle register
whose units are determined by a bus-period register. The periodic
timer is used to implement both periodic and oneshot clock event
modes; in oneshot mode the interrupt handler simply disables the timer
as soon as it fires.
Despite its device tree node representing an interrupt for the PIT,
the actual irq generated is programmable, not hard-wired. The driver
is responsible for programming the PIT to generate the hardware irq
number that the DT assigns to it.
On SMP configurations, J-Core provides cpu-local instances of the PIT;
no broadcast timer is needed. This driver supports the creation of the
necessary per-cpu clock_event_device instances.
A nanosecond-resolution clocksource is provided using the J-Core "RTC"
registers, which give a 64-bit seconds count and 32-bit nanoseconds
that wrap every second. The driver converts these to a full-range
32-bit nanoseconds count.
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Most of these are CC'd for stable, but there are a few fixing issues
introduced during the recent merge window too.
There's also a fix for the xgene PMU driver, but it seemed daft to
send as a separate pull request, so I've included it here with the
rest of the fixes.
- Fix ACPI boot due to recent broken NUMA changes
- Fix remote enabling of CPU features requiring PSTATE bit manipulation
- Add address range check when emulating user cache maintenance
- Fix LL/SC loops that allow compiler to introduce memory accesses
- Fix recently added write_sysreg_s macro
- Ensure MDCR_EL2 is initialised on qemu targets without a PMU
- Avoid kaslr breakage due to MODVERSIONs and DYNAMIC_FTRACE
- Correctly drive recent ld when building relocatable Image
- Remove junk IS_ERR check from xgene PMU driver added during merge window
- pr_cont fixes after core changes in the merge window"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: remove pr_cont abuse from mem_init
arm64: fix show_regs fallout from KERN_CONT changes
arm64: kernel: force ET_DYN ELF type for CONFIG_RELOCATABLE=y
arm64: suspend: Reconfigure PSTATE after resume from idle
arm64: mm: Set PSTATE.PAN from the cpu_enable_pan() call
arm64: cpufeature: Schedule enable() calls instead of calling them via IPI
arm64: Cortex-A53 errata workaround: check for kernel addresses
arm64: percpu: rewrite ll/sc loops in assembly
arm64: swp emulation: bound LL/SC retries before rescheduling
arm64: sysreg: Fix use of XZR in write_sysreg_s
arm64: kaslr: keep modules close to the kernel when DYNAMIC_FTRACE=y
arm64: kernel: Init MDCR_EL2 even in the absence of a PMU
perf: xgene: Remove bogus IS_ERR() check
arm64: kernel: numa: fix ACPI boot cpu numa node mapping
arm64: kaslr: fix breakage with CONFIG_MODVERSIONS=y
|
|
Pull Ceph fixes from Ilya Dryomov:
"An rbd exclusive-lock edge case fix and several filesystem fixups.
Nikolay's error path patch is tagged for stable, everything else but
readdir vs frags race was introduced in this merge window"
* tag 'ceph-for-4.9-rc2' of git://github.com/ceph/ceph-client:
ceph: fix non static symbol warning
ceph: fix uninitialized dentry pointer in ceph_real_mount()
ceph: fix readdir vs fragmentation race
ceph: fix error handling in ceph_read_iter
rbd: don't retry watch reregistration if header object is gone
rbd: don't wait for the lock forever if blacklisted
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.9 rc2.
This time I have also included a few changes for a memstick driver
which has a corresponding mmc driver. They use the same USB device as
parent, hence both needs to play nice with runtime PM, which they
didn't.
MMC core:
- Update MAINTAINERS as the mmc tree moved to kernel.org
- A few fixes for HS400es mode
- A few other minor fixes
MMC host:
- sdhci: Fix an issue when dealing with stop commands
- sdhci-pci: Fix a bus power failure issue
- sdhci-esdhc-imx: Correct two register accesses
- sdhci-of-arasan: Fix the 1.8V I/O signal switch behaviour
- rtsx_usb_sdmmc: Fix runtime PM issues
Other: (Because of no maintainer)
- memstick: rtsx_usb_ms: Fix runtime PM issues"
* tag 'mmc-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
MAINTAINERS: mmc: Move the mmc tree to kernel.org
memstick: rtsx_usb_ms: Manage runtime PM when accessing the device
memstick: rtsx_usb_ms: Runtime resume the device when polling for cards
mmc: rtsx_usb_sdmmc: Handle runtime PM while changing the led
mmc: rtsx_usb_sdmmc: Avoid keeping the device runtime resumed when unused
mmc: sdhci: cast unsigned int to unsigned long long to avoid unexpeted error
mmc: sdhci-esdhc-imx: Correct two register accesses
mmc: sdhci-pci: Fix bus power failing to enable for some Intel controllers
mmc: sdhci-pci: Let devices define their own sdhci_ops
mmc: sdhci: Rename sdhci_set_power() to sdhci_set_power_noreg()
mmc: sdhci: Fix SDHCI_QUIRK2_STOP_WITH_TC
mmc: core: Annotate cmd_hdr as __le32
mmc: sdhci-of-arasan: add sdhci_arasan_voltage_switch for arasan, 5.1
mmc: core: changes frequency to hs_max_dtr when selecting hs400es
mmc: core: switch to 1V8 or 1V2 for hs400es mode
mmc: block: add missing header dependencies
mmc: sdhci-of-arasan: Fix non static symbol warning
|
|
It really looks bad without a newline.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Core drivers for J-Core SoCs will be selected implicitly via
CONFIG_SH_JCORE_SOC instead. Based on a corresponding change to the
clocksource/timer driver requested by Daniel Lezcano.
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/883a3d17084003e3cf21bab73ec12828fe4ff6c6.1476899495.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
target_complete_cmd_with_length"
This reverts commit c1ccbfe0311e2380a6d2dcb0714b36904f5d586f.
Reverting this patch, as it incorrectly assumes the additional length
for INQUIRY in target_complete_cmd_with_length() is SCSI allocation
length, which breaks existing user-space code when SCSI allocation
length is smaller than additional length.
root@scsi-mq:~# sg_inq --len=4 -vvvv /dev/sdb
found bsg_major=253
open /dev/sdb with flags=0x800
inquiry cdb: 12 00 00 00 04 00
duration=0 ms
inquiry: pass-through requested 4 bytes (data-in) but got -28 bytes
inquiry: pass-through can't get negative bytes, say it got none
inquiry: got too few bytes (0)
INQUIRY resid (32) should never exceed requested len=4
inquiry: failed requesting 4 byte response: Malformed response to
SCSI command [resid=32]
AFAICT the original change was not to address a specific host issue,
so go ahead and revert to original logic for now.
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sumit Rai <sumitrai96@gmail.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a bug where a local EXTENDED_COPY WRITE or READ
backend I/O request would always return SAM_STAT_CHECK_CONDITION,
even if underlying xcopy_pt_cmd->se_cmd generated a different
SCSI status code.
ESX host environments expect to hit SAM_STAT_RESERVATION_CONFLICT
for certain scenarios, and SAM_STAT_CHECK_CONDITION results in
non-retriable status for these cases.
Tested on v4.1.y with ESX v5.5u2+ with local IBLOCK backend copy.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Dinesh Israni <ddi@datera.io>
Signed-off-by: Dinesh Israni <ddi@datera.io>
Cc: Dinesh Israni <ddi@datera.io>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a bug where EXTENDED_COPY across multiple LUNs
results in a CHECK_CONDITION when the source + destination are not
located on the same physical node.
ESX Host environments expect sense COPY_ABORTED w/ COPY TARGET DEVICE
NOT REACHABLE to be returned when this occurs, in order to signal
fallback to local copy method.
As described in section 6.3.3 of spc4r22:
"If it is not possible to complete processing of a segment because the
copy manager is unable to establish communications with a copy target
device, because the copy target device does not respond to INQUIRY,
or because the data returned in response to INQUIRY indicates
an unsupported logical unit, then the EXTENDED COPY command shall be
terminated with CHECK CONDITION status, with the sense key set to
COPY ABORTED, and the additional sense code set to COPY TARGET DEVICE
NOT REACHABLE."
Tested on v4.1.y with ESX v5.5u2+ with BlockCopy across multiple nodes.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Dinesh Israni <ddi@datera.io>
Signed-off-by: Dinesh Israni <ddi@datera.io>
Cc: Dinesh Israni <ddi@datera.io>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a regression in >= v4.1.y code where the original
SCF_ACK_KREF assignment in target_get_sess_cmd() was dropped upstream
in commit 054922bb, but the series for addressing TMR ABORT_TASK +
LUN_RESET with fabric session reinstatement in commit febe562c20 still
depends on this code in transport_cmd_finish_abort().
The regression manifests itself as a se_cmd->cmd_kref +1 leak, where
ABORT_TASK + LUN_RESET can hang indefinately for a specific I_T session
for drivers using SCF_ACK_KREF, resulting in hung kthreads.
This patch has been verified with v4.1.y code.
Reported-by: Vaibhav Tandon <vst@datera.io>
Tested-by: Vaibhav Tandon <vst@datera.io>
Cc: Vaibhav Tandon <vst@datera.io>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If iscsi-target receives NOP OUT with ITT and TTT
set to 0xffffffff it allocates iscsi_cmd but
does not free the cmd, so free iscsi_cmd in this case.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Trivial fix to spelling mistakes in pr_debug message and comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We no longer use a ringbuffer for the data area, so this might cause
confusion. Just call it the data area.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
