| Age | Commit message (Collapse) | Author |
|---|
|
This multiplication should be done in 64-bit, not 32-bit.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The condition "if (irq_status == 0)" already ensures that one half of
the ternary ?: is dead. I think this should probably actually be a FAIL,
not a PASS.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jamie Iles <jamie@jamieiles.com>
|
|
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
These multiplications are done with 32-bit arithmetic, then converted to
64-bit. We should widen the integers first to prevent overflow. This
could be a problem for large (>4GB) MTD's.
Detected by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
|
|
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
MTD used to allow compiling out character device support. This was
dropped in the following commit, but some of the accompanying logic was
never dropped:
commit 660685d9d1b4730f0b5ca97fa95f272f99c63bce
Author: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Date: Thu Mar 14 13:27:40 2013 +0200
mtd: merge mtdchar module with mtdcore
The weird logic was flagged by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
There is one theoretical case that could fall through to using an
uninitialized value as the return code. Let's give it a value of 0.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
When checking the upper boundary (i.e., whether an address is higher
than the maximum size of the MTD), we should be doing an inclusive check
(greater or equal). For instance, an address of 16MB (0x1000000) on a
16MB device is invalid.
The strengthening of this bounds check is redundant for those which
already have a address+length check and ensure that the length is
non-zero, but let's just fix them all, for completeness.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The variable 'retries' is never modified, so if the reset operation
never is going to complete, we'll get stuck in an infinite loop.
It looks like the intention was to decrement 'retries' on every loop.
Untested.
Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Do nand reset before write protect check.
If we want to check the WP# low or high through STATUS READ and check bit 7,
we must reset the device, other operation (eg.erase/program a locked block) can
also clear the bit 7 of status register.
As we know the status register can be refreshed, if we do some operation to trigger it,
for example if we do erase/program operation to one block that is locked, then READ STATUS,
the bit 7 of READ STATUS will be 0 indicate the device in write protect, then if we do
erase/program operation to another block that is unlocked, the bit 7 of READ STATUS will
be 1 indicate the device is not write protect.
Suppose we checked the bit 7 of READ STATUS is 0 then judge the WP# is low (write protect),
but in this case the WP# maybe high if we do erase/program operation to a locked block,
so we must reset the device if we want to check the WP# low or high through STATUS READ and
check bit 7.
Signed-off-by: White Ding <bpqw@micron.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Fixed checkpatch warnings: "WARNING: Prefer seq_puts to seq_printf"
This patch is created with reference to the ongoing lkml thread
https://lkml.org/lkml/2014/7/15/646
where Andrew Morton wrote:
"
- puts is presumably faster
- puts doesn't go rogue if you accidentally pass it a "%".
- this patch would actually make compiled object files few bytes smaller.
Perhaps because seq_printf() is a varargs function, forcing the
caller to pass args on the stack instead of in registers.
"
Signed-off-by: Samarth Parikh <samarthp@ymail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
MAP10 command with '0x2000' data sets up a read-ahead/write access.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This commit adds the support in the spi-nor driver of the Micron
M25PX80 flash, a 8 Mbit SPI flash from Micron.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
PMECC can support 512, 1k, 2k, 4k, 8k page size.
The driver currently only support 2k page size nand flash. So this patch
add support to 512, 1k, 4k and 8k page size nand flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Some nand with 8k page size like Micron MT29F32G08ABAAAWP need more than 20us.
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Use NULL instead of 0 when returning an address. This fixes a
sparse warning.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
We check "cs" for array overflows but we don't check for underflows and
it upsets the static checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.
brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3
Bisect points to commit 71e75c97f97a ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.
out_delay:
- if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+ if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
blk_delay_queue(q, SCSI_QUEUE_DELAY);
}
'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
linux-2.6/drivers/usb/wusbcore/wa-xfer.c: In function 'wa_buf_in_cb':
linux-2.6/drivers/usb/wusbcore/wa-xfer.c:2590: warning: 'rpipe' may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Suggested-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
linux-2.6/drivers/usb/core/hub.c: In function 'usb_disconnect':
linux-2.6/drivers/usb/core/hub.c:2110: warning: 'hub' may be used uninitialized in this function
linux-2.6/drivers/usb/core/hub.c:2111: warning: 'port1' may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
linux-2.6/drivers/usb/dwc2/gadget.c: In function 's3c_hsotg_irq_enumdone':
linux-2.6/drivers/usb/dwc2/gadget.c:1904: warning: 'ep_mps' may be used uninitialized in this function
Acked-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When we manually need to move the TR dequeue pointer we need to set the
correct cycle bit as well. Previously we used the trb pointer from the
last event received as a base, but this was changed in
commit 1f81b6d22a59 ("usb: xhci: Prefer endpoint context dequeue pointer")
to use the dequeue pointer from the endpoint context instead
It turns out some Asmedia controllers advance the dequeue pointer
stored in the endpoint context past the event triggering TRB, and
this messed up the way the cycle bit was calculated.
Instead of adding a quirk or complicating the already hard to follow cycle bit
code, the whole cycle bit calculation is now simplified and adapted to handle
event and endpoint context dequeue pointer differences.
Fixes: 1f81b6d22a59 ("usb: xhci: Prefer endpoint context dequeue pointer")
Reported-by: Maciej Puzio <mx34567@gmail.com>
Reported-by: Evan Langlois <uudruid74@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Maciej Puzio <mx34567@gmail.com>
Tested-by: Evan Langlois <uudruid74@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
AMD xHC also needs short tx quirk after tested on most of chipset
generations. That's because there is the same incorrect behavior like
Fresco Logic host. Please see below message with on USB webcam
attached on xHC host:
[ 139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
Reported-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Shriraj-Rai P <shriraj-rai.p@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using a Renesas uPD720231 chipset usb-3 uas to sata bridge with a 120G
Crucial M500 ssd, model string: Crucial_ CT120M500SSD1, together with a
the integrated Intel xhci controller on a Haswell laptop:
00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)
The following error gets logged to dmesg:
xhci error: Transfer event TRB DMA ptr not part of current TD
Treating COMP_STOP the same as COMP_STOP_INVAL when no event_seg gets found
fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit [5ee0f803cc3a: usbcore: don't log on consecutive debounce
failures of the same port] added the check of the reliable port, but
it also replaced the device argument to dev_err() wrongly, which leads
to a NULL dereference.
This patch restores the right device, port_dev->dev. Also, since
dev_err() itself shows the port number, reduce the port number shown
in the error message, essentially reverting to the state before the
commit 5ee0f803cc3a.
[The fix suggested by Hannes, and the error message cleanup suggested
by Alan Stern]
Fixes: 5ee0f803cc3a ('usbcore: don't log on consecutive debounce failures of the same port')
Reported-by: Hannes Reinecke <hare@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 1490434f0da63afc6006411c8829c6a7935a4e7e.
Several people have reported regressions with this patch on kabini.
|
|
Need to initialize the mask to 0 on init, otherwise it
keeps increasing.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=82581
v2: also fix cu count
v3: split count fix into separate patch
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@vger.kernel.org
|
|
This fixes the CU count reported to userspace for
OpenCL.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=82581
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@vger.kernel.org
|
|
Now that the PFP and ME synchronization is fixed, we
can enable this again reliably.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
|
|
Fixes lockups due to CP read GPUVM faults when running piglit on Cape
Verde.
v2 (chk): apply the fix to R600+ as well, on CIK only the GFX CP has
a PFP, add more comments to R600 code, enable flushing again
v3: (agd5f): only apply to 7xx+. r6xx does not have the packet.
v4: (agd5f): split flush change into a separate patch, fix formatting
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
|
|
If the display hw was reset or a hard reset was used,
we need to re-init some of the common display hardware as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
pm_suspend is handled in the radeon_suspend callbacks.
pm_resume has special handling depending on whether
dpm or legacy pm is enabled. Change radeon_gpu_reset
to mirror the behavior in the suspend and resume
pathes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
|
|
The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This reverts commit a9232076374334ca2bc2a448dfde96d38a54349a.
It introduced a dead lock, and did not fix anything.
it made netif_tx_lock() be called in IRQ context, but in softirq context,
the same lock is locked without disabling IRQ. In fact, the commit a923207637
did not fix anything, since netif_stop_queue did not free the any resource
[ 10.154920] =================================
[ 10.156026] [ INFO: inconsistent lock state ]
[ 10.156026] 3.16.0-rc5+ #13 Not tainted
[ 10.156026] ---------------------------------
[ 10.156026] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[ 10.156026] swapper/1/0 [HC0[0]:SC1[5]:HE1:SE0] takes:
[ 10.156026] (_xmit_ETHER){?.-...}, at: [<80948b6a>] sch_direct_xmit+0x7a/0x250
[ 10.156026] {IN-HARDIRQ-W} state was registered at:
[ 10.156026] [<804811f0>] __lock_acquire+0x800/0x17a0
[ 10.156026] [<804828ba>] lock_acquire+0x6a/0xf0
[ 10.156026] [<809ed477>] _raw_spin_lock+0x27/0x40
[ 10.156026] [<8088d508>] gether_disconnect+0x68/0x280
[ 10.156026] [<8088e777>] eem_set_alt+0x37/0xc0
[ 10.156026] [<808847ce>] composite_setup+0x30e/0x1240
[ 10.156026] [<8088b8ae>] pch_udc_isr+0xa6e/0xf50
[ 10.156026] [<8048abe8>] handle_irq_event_percpu+0x38/0x1e0
[ 10.156026] [<8048adc1>] handle_irq_event+0x31/0x50
[ 10.156026] [<8048d94b>] handle_fasteoi_irq+0x6b/0x140
[ 10.156026] [<804040a5>] handle_irq+0x65/0x80
[ 10.156026] [<80403cfc>] do_IRQ+0x3c/0xc0
[ 10.156026] [<809ee6ae>] common_interrupt+0x2e/0x34
[ 10.156026] [<804668c5>] finish_task_switch+0x65/0xd0
[ 10.156026] [<809e89df>] __schedule+0x20f/0x7d0
[ 10.156026] [<809e94aa>] schedule_preempt_disabled+0x2a/0x70
[ 10.156026] [<8047bf03>] cpu_startup_entry+0x143/0x410
[ 10.156026] [<809e2e61>] rest_init+0xa1/0xb0
[ 10.156026] [<80ce2a3b>] start_kernel+0x336/0x33b
[ 10.156026] [<80ce22ab>] i386_start_kernel+0x79/0x7d
[ 10.156026] irq event stamp: 52070
[ 10.156026] hardirqs last enabled at (52070): [<809375de>] neigh_resolve_output+0xee/0x2a0
[ 10.156026] hardirqs last disabled at (52069): [<809375a8>] neigh_resolve_output+0xb8/0x2a0
[ 10.156026] softirqs last enabled at (52020): [<8044401f>] _local_bh_enable+0x1f/0x50
[ 10.156026] softirqs last disabled at (52021): [<80404036>] do_softirq_own_stack+0x26/0x30
[ 10.156026]
[ 10.156026] other info that might help us debug this:
[ 10.156026] Possible unsafe locking scenario:
[ 10.156026]
[ 10.156026] CPU0
[ 10.156026] ----
[ 10.156026] lock(_xmit_ETHER);
[ 10.156026] <Interrupt>
[ 10.156026] lock(_xmit_ETHER);
[ 10.156026]
[ 10.156026] *** DEADLOCK ***
[ 10.156026]
[ 10.156026] 4 locks held by swapper/1/0:
[ 10.156026] #0: (((&idev->mc_ifc_timer))){+.-...}, at: [<8044b100>] call_timer_fn+0x0/0x190
[ 10.156026] #1: (rcu_read_lock){......}, at: [<a0577c40>] mld_sendpack+0x0/0x590 [ipv6]
[ 10.156026] #2: (rcu_read_lock_bh){......}, at: [<a055680c>] ip6_finish_output2+0x4c/0x7f0 [ipv6]
[ 10.156026] #3: (rcu_read_lock_bh){......}, at: [<8092e510>] __dev_queue_xmit+0x0/0x5f0
[ 10.156026]
[ 10.156026] stack backtrace:
[ 10.156026] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.16.0-rc5+ #13
[ 10.156026] 811dbb10 00000000 9e919d10 809e6785 9e8b8000 9e919d3c 809e561e 80b95511
[ 10.156026] 80b9545a 80b9543d 80b95450 80b95441 80b957e4 9e8b84e0 00000002 8047f7b0
[ 10.156026] 9e919d5c 8048043b 00000002 00000000 9e8b8000 00000001 00000004 9e8b8000
[ 10.156026] Call Trace:
[ 10.156026] [<809e6785>] dump_stack+0x48/0x69
[ 10.156026] [<809e561e>] print_usage_bug+0x18f/0x19c
[ 10.156026] [<8047f7b0>] ? print_shortest_lock_dependencies+0x170/0x170
[ 10.156026] [<8048043b>] mark_lock+0x53b/0x5f0
[ 10.156026] [<804810cf>] __lock_acquire+0x6df/0x17a0
[ 10.156026] [<804828ba>] lock_acquire+0x6a/0xf0
[ 10.156026] [<80948b6a>] ? sch_direct_xmit+0x7a/0x250
[ 10.156026] [<809ed477>] _raw_spin_lock+0x27/0x40
[ 10.156026] [<80948b6a>] ? sch_direct_xmit+0x7a/0x250
[ 10.156026] [<80948b6a>] sch_direct_xmit+0x7a/0x250
[ 10.156026] [<8092e6bf>] __dev_queue_xmit+0x1af/0x5f0
[ 10.156026] [<80947fc0>] ? ether_setup+0x80/0x80
[ 10.156026] [<8092eb0f>] dev_queue_xmit+0xf/0x20
[ 10.156026] [<8093764c>] neigh_resolve_output+0x15c/0x2a0
[ 10.156026] [<a0556927>] ip6_finish_output2+0x167/0x7f0 [ipv6]
[ 10.156026] [<a0559b05>] ip6_finish_output+0x85/0x1c0 [ipv6]
[ 10.156026] [<a0559cb7>] ip6_output+0x77/0x240 [ipv6]
[ 10.156026] [<a0578163>] mld_sendpack+0x523/0x590 [ipv6]
[ 10.156026] [<80480501>] ? mark_held_locks+0x11/0x90
[ 10.156026] [<a057947d>] mld_ifc_timer_expire+0x15d/0x280 [ipv6]
[ 10.156026] [<8044b168>] call_timer_fn+0x68/0x190
[ 10.156026] [<a0579320>] ? igmp6_group_added+0x150/0x150 [ipv6]
[ 10.156026] [<8044b3fa>] run_timer_softirq+0x16a/0x240
[ 10.156026] [<a0579320>] ? igmp6_group_added+0x150/0x150 [ipv6]
[ 10.156026] [<80444984>] __do_softirq+0xd4/0x2f0
[ 10.156026] [<804448b0>] ? tasklet_action+0x100/0x100
[ 10.156026] [<80404036>] do_softirq_own_stack+0x26/0x30
[ 10.156026] <IRQ> [<80444d05>] irq_exit+0x65/0x70
[ 10.156026] [<8042d758>] smp_apic_timer_interrupt+0x38/0x50
[ 10.156026] [<809ee91f>] apic_timer_interrupt+0x2f/0x34
[ 10.156026] [<8048007b>] ? mark_lock+0x17b/0x5f0
[ 10.156026] [<8040a912>] ? default_idle+0x22/0xf0
[ 10.156026] [<8040b13e>] arch_cpu_idle+0xe/0x10
[ 10.156026] [<8047bfc6>] cpu_startup_entry+0x206/0x410
[ 10.156026] [<8042bfbd>] start_secondary+0x19d/0x1e0
Acked-by: Tony Lindgren <tony@atomide.com>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Westfahl <jeff.westfahl@ni.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Pull md bugfixes from Neil Brown:
"Here are the bug-fixes I promised :-)
Funny how you start looking for one and other start appearing.
- raid6 data corruption during recovery
- raid6 livelock
- raid10 memory leaks"
* tag 'md/3.17-fixes' of git://neil.brown.name/md:
md/raid10: always initialise ->state on newly allocated r10_bio
md/raid10: avoid memory leak on error path during reshape.
md/raid10: Fix memory leak when raid10 reshape completes.
md/raid10: fix memory leak when reshaping a RAID10.
md/raid6: avoid data corruption during recovery of double-degraded RAID6
md/raid5: avoid livelock caused by non-aligned writes.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Marvell MVEBU
- Remove ARCH_KIRKWOOD dependency (Andrew Lunn)
NVIDIA Tegra
- Add debugfs support (Thierry Reding)
Synopsys DesignWare
- Look for configuration space in 'reg', not 'ranges' (Kishon Vijay Abraham I)
- Program ATU with untranslated address (Kishon Vijay Abraham I)
- Add config access-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
- Add MSI-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
TI DRA7xx
- Add TI DR7xx PCIe driver (Kishon Vijay Abraham I)"
* tag 'pci-v3.17-changes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Add MSI-related pcie_host_ops for v3.65 hardware
PCI: designware: Add config access-related pcie_host_ops for v3.65 hardware
PCI: dra7xx: Add TI DRA7xx PCIe driver
PCI: designware: Program ATU with untranslated address
PCI: designware: Look for configuration space in 'reg', not 'ranges'
PCI: tegra: Add debugfs support
PCI: mvebu: Remove ARCH_KIRKWOOD dependency
|
|
Pull devicetree fixes from Grant Likely:
"Three more commits needed for v3.17: A bug fix for reserved regions
based at address zero, a clarification on how to interpret existence
of both interrupts and interrupts-extended properties, and a fix to
allow device tree testcases to run on any platform"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: Fix lookup to use 'interrupts-extended' property first
Enabling OF selftest to run without machine's devicetree
of: Allow mem_reserve of memory with a base address of zero
|
|
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In case of error, the function memdup_user() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
"ret" should be signed. It's only used for zero and negative error
codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
As, the interrupt for DMA is counted from 1, so need to checked
the USBA_NR_DMAS, in old way, it only check (USBA_NR_DMAS - 1),
so fix it.
Reported-by: Max Liao <liaops@embest-tech.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
According to the datasheet, PHYPARAM1_PCS_TXDEEMPH is set as
6 bits [5:0]. Thus, the bit mask should be set as 0x3f, instead
of 0x1f.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
After dbgp_bind()-dbgp_unbind() cycle happens, static variable dbgp
contains pointers to already deallocated memory (dbgp.serial and dbgp.req).
If the next dbgp_bind() fails, for example in usb_ep_alloc_request(),
dbgp_bind() calls dbgp_unbind() on failure path,
and dbgp_unbind() frees dbgp.serial that still stores a pointer
to already deallocated memory.
The patch sets pointers to NULL in dbgp_unbind().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Using kfree to free data allocated with devm_kzalloc causes double frees.
The Coccinelle semantic patch that fixes this problem is as follows:
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When __usb_find_phy_dev() does not return error and
try_module_get() fails, return -ENODEV.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
