| Age | Commit message (Collapse) | Author |
|---|
|
The "stm32_pwr_wakeup" is optional per the binding and the driver
handles its absence gracefully. Request it with
platform_get_irq_byname_optional, so its absence doesn't needlessly
clutter the log.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The specification of a "eth-ck" and a "ptp_ref" clock is optional per
the binding and the driver handles them gracefully.
Demote the output to an info message accordingly.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If one types "failed to get enet clock" or similar into google
there are ~370k hits. The vast majority are people debugging
problems unrelated to this adapter, or bragging about their
rpi's. Further, the DT clock bindings here are optional.
Given that its not a fatal situation with common DT based
systems, lets reduce the severity so people aren't seeing failure
messages in everyday operation.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARM/ACPI machines should utilize self describing hardware
when possible. The MAC address on the BCMGENET can be
read from the adapter if a full featured firmware has already
programmed it. Lets try using the address already programmed,
if it appears to be valid.
It should be noted that while we move the macaddr logic below
the clock and power logic in the driver, none of that code will
ever be active in an ACPI environment as the device will be
attached to the acpi power domain, and brought to full power
with all clocks enabled immediately before the device probe
routine is called.
One side effect of the above tweak is that while its now
possible to read the MAC address via _DSD properties, it should
be avoided.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rpi4 is capable of booting in ACPI mode with the latest
edk2-platform commits. As such it would be helpful if the genet
platform device were usable.
To achieve this we add a new MODULE_DEVICE_TABLE, and convert
a few dt specific methods to their generic device_ calls. Until
the next patch, ACPI based machines will fallback on random
mac addresses.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The unimac mdio driver falls back to scanning the
entire bus if its given an appropriate mask. In ACPI
mode we expect that the system is well behaved and
conforms to recent versions of the specification.
We then utilize phy_find_first(), and
phy_connect_direct() to find and attach to the
discovered phy during net_device open. While its
apparently possible to build a genet based device
with multiple phys on a single mdio bus, this works
for current machines. Further, this driver makes
a number of assumptions about the platform device,
mac, mdio and phy all being 1:1. Lastly, It also
avoids having to create references across the ACPI
namespace hierarchy.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DT phy mode is similar to what we want for ACPI
lets factor it out of the of path, and change the
of_ call to device_.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It appears most ethernet drivers follow one of two main strategies
for mdio bus/phy management. A monolithic model where the net driver
itself creates, probes and uses the phy, and one where an external
mdio/phy driver instantiates the mdio bus/phy and the net driver
only attaches to a known phy. Usually in this latter model the phys
are discovered via DT relationships or simply phy name/address
hardcoding.
This is a shame because modern well behaved mdio buses are self
describing and can be probed. The mdio layer itself is fully capable
of this, yet there isn't a clean way for a standalone net driver
to attach and enumerate the discovered devices. This is because
outside of of_mdio_find_bus() there isn't a straightforward way
to acquire the mii_bus pointer.
So, lets add a mdio_find_bus which can return the mii_bus based
only on its name.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy-mode = "gmii" is confusing because it may mean that the port
supports the 8-bit-wide parallel data interface pinout, which it
doesn't.
It may also be confusing because one of the "gmii" internal ports is
actually overclocked to run at 2.5Gbps (even though, yes, as far as the
switch MAC is concerned, it still thinks it's gigabit).
So use the phy-mode = "internal" property to describe the internal ports
inside the NXP LS1028A chip (the ones facing the ENETC). The change
should be fine, because the device tree bindings document is yet to be
introduced, and there are no stable DT blobs in use.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/bareudp.c: In function 'bareudp_xmit_skb':
drivers/net/bareudp.c:346:9: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized]
346 | return err;
| ^~~
drivers/net/bareudp.c: In function 'bareudp6_xmit_skb':
drivers/net/bareudp.c:407:9: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized]
407 | return err;
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Special handling is needed in bareudp module for IP & MPLS as they
support more than one ethertypes.
MPLS has 2 ethertypes. 0x8847 for MPLS unicast and 0x8848 for MPLS multicast.
While decapsulating MPLS packet from UDP packet the tunnel destination IP
address is checked to determine the ethertype. The ethertype of the packet
will be set to 0x8848 if the tunnel destination IP address is a multicast
IP address. The ethertype of the packet will be set to 0x8847 if the
tunnel destination IP address is a unicast IP address.
IP has 2 ethertypes.0x0800 for IPV4 and 0x86dd for IPv6. The version
field of the IP header tunnelled will be checked to determine the ethertype.
This special handling to tunnel additional ethertypes will be disabled
by default and can be enabled using a flag called multiproto. This flag can
be used only with ethertypes 0x8847 and 0x0800.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPLS, IP, NSH etc.
The Bareudp tunnel module provides a generic L3 encapsulation
tunnelling module for tunnelling different protocols like MPLS,
IP,NSH etc inside a UDP tunnel.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IDT 82P33 Synchronization Management Unit (SMU) family provides
tools to manage timing references, clock sources and
timing paths for IEEE 1588 / Precision Time Protocol (PTP) and
Synchronous Ethernet (SyncE) based clocks. The device supports up
to three independent timing paths that control: PTP clock synthesis;
SyncE clock generation; and general purpose frequency translation.
The device supports physical layer timing with Digital PLLs (DPLLs)
and it supports packet based timing with Digitally Controlled
Oscillators (DCOs). This patch adds support for ptp clock based on
the device.
Changes since v1:
- As suggested by Richard Cochran:
1. Replace _mask_bit_count with the existing hweight8
2. Prefix all functions with idt82p33
3. Fix white space issues in Kconfig and Makefile
4. Remove forward declaration
5. Use adjfine instead of adjfreq for better resolution
- As suggested by David Miller:
1. Replace CHAN_INIT macro with a static function
idt82p33_channel_init
2. Employ reverse christmas tree ordering for local
variables
3. Fix indentation problem by appropriate number of
TAB then SPACE character
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the trap group used to report ACL drops. Setup the trap IDs for
ingress/egress flow action drop. Register the two packet traps
associated with ACL trap group with devlink during driver
initialization. As these are "source traps", set the disabled
trap group to be the dummy, discarding as many packets in HW
as possible.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For "source traps" it is not possible to change HPKT action to discard.
But there is still need to disallow packets arriving to CPU as much as
possible. Handle this by introduction of a "dummy group". It has a
"thin" policer, which passes as less packets to CPU as possible. The
rest is going to be discarded there. The "dummy group" is to be used
later on by ACL trap (which is a "source trap").
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the mlxsw_listener struct to contain trap group for disabled
traps too. Rename the original "trap_group" item to "en_trap_group" as
it represents enabled state. Let both groups be the same for MLXSW_RXL
however extend MLXSW_RXL_DIS to register separate groups for enable and
disable.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For source traps, the "thin policer" is going to be used in order
to reduce the amount of trapped packets to minimum. However, there
will be still small number of packets coming in that need to be dropped
in the driver. Allow to enable/disable rx_listener related to specific
trap in order to prevent unwanted packets to go up the stack.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new set of traps:
DISCARD_INGRESS_ACL and DISCARD_EGRESS_ACL
Set the trap_action from NOP to TRAP which causes the packets dropped
by the TRAP action to be trapped under new trap IDs, depending on the
ingress/egress binding point.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ACL flex action will have to know if it is in ingress or egress,
so it can use correct trap ID. Pass the ingress indication down to it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Action drop is going to be tracked by two separate traps, one for
ingress and one for egress. Prepare for it and disallow the possibility
to have drop action in blocks which are bound to both ingress and
egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Count the number of ingress and egress block bindings. Use the egress
counter in "is_egress_bound" helper. Add couple of helpers to check
ingress and mixed bound.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
only action
Rename function mlxsw_core_trap_action_set() to
mlxsw_core_trap_state_set() and pass bool enabled instead of action.
Figure out the action according to the enabled state there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The listener fields en_action and dis_action now contain the actions to
be used for TRAP and DROP devlink trap actions. Use them directly
instead of the hard-coded values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new macro MLXSW_RXL_DIS that allows to register listeners
as disabled. That allows that from now on, the "action" can be
understood always as "enabled action" and "unreg_action" as "disabled
action". Rename them and treat them accordingly.
Use the new macro for defining drops in spectrum_trap.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently it does not really matter if it is set to DISCARD or
SET_FW_DEFAULT because it is set only during unregister of the listener.
The unreg_action is going to be used for disabling the listener too, so
change to SET_FW_DEFAULT and ensure the HW is going to behave correctly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use linux kernel version for ethtool and module versions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop constant driver version in favour of global linux kernel.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to keep module and driver versions in in-tree
kernel code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to set "N/A" if FW is not available.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delete module version in favor of global and unique linux kernel.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert AMD drivers to respect universal linux kernel version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upstream drivers are managed inside global repository and released all
together, this ensure that driver version is the same as linux kernel,
so update amazon drivers to properly reflect it.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert to use default version provided by ethtool.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The acenic driver assigns FW version in driver version field,
as part of cleanup driver version, set FW version properly.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need in custom driver version for in-tree code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use standard variant of the driver version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need in driver version for in-tree kernel code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If FW version is not available, it is enough to leave that field as
empty, there is no need to write N/A.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If FW version is not available, it is enough to leave that field as
empty, there is no need to write N/A.
The driver version is replaced in favor of generally available
in-tree variant.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delete useless driver version in favor of default ones.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to mislead users by providing different versions for
driver, ethtool and modules. Delete driver assignments and let use
the default one.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delete constant driver and module versions in favor of
standard global version which is unique to whole kernel.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The in-kernel code has already unique version, which is based
on Linus's tag, update the bond driver to be consistent with that
version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pointer 'client' is being initialized with a value that is never
read, it is being updated later on. The initialization is redundant
and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
