| Age | Commit message (Collapse) | Author |
|---|
|
The datasheets have the following note for the conversion time
specification: "This parameter is specified by design and/or
characterization and it is not tested in production."
Parts have been seen that require more time to do 14-bit conversions for
the relative humidity channel. The result is ENXIO due to the address
phase of a transfer not getting an ACK.
Delay an additional 1 ms per conversion to allow for additional margin.
Fixes: 4839367d99e3 ("iio: humidity: add HDC100x support")
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Link: https://lore.kernel.org/r/20210614141820.2034827-1-chris.lesiak@licor.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
With CONFIG_SPI=y and CONFIG_I2C=m, building fxls8962af into vmlinux
causes a link error against the I2C module:
aarch64-linux-ld: drivers/iio/accel/fxls8962af-core.o: in function `fxls8962af_fifo_flush':
fxls8962af-core.c:(.text+0x3a0): undefined reference to `i2c_verify_client'
Work around it by adding a Kconfig dependency that forces the SPI driver
to be a loadable module whenever I2C is a module.
Fixes: af959b7b96b8 ("iio: accel: fxls8962af: fix errata bug E3 - I2C burst reads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721151330.2176653-1-arnd@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Set reset pin direction to output as the reset pin needs to be an active
low output pin.
Co-developed-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Antti Keränen <detegr@rbx.email>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Fixes: ecb010d44108 ("iio: imu: adis: Refactor adis_initial_startup")
Link: https://lore.kernel.org/r/20210708095425.13295-1-detegr@rbx.email
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.
Fixes: e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix this warning from kernel test robot:
smatch warnings:
drivers/iio/accel/fxls8962af-core.c:640
fxls8962af_i2c_raw_read_errata3() error: uninitialized symbol 'ret'.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Fixes: af959b7b96b8 ("iio: accel: fxls8962af: fix errata bug E3 - I2C burst reads")
Link: https://lore.kernel.org/r/20210709071727.2453536-1-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Two fixes:
- Fix a MIPS IRQ handling RCU bug
- Remove a DocBook annotation for a parameter that doesn't exist
anymore"
* tag 'irq-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mips: Fix RCU violation when using irqdomain lookup on interrupt entry
genirq/irqdesc: Drop excess kernel-doc entry @lookup
|
|
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes and clean ups in the core and various
drivers.
The only core change in behaviour is the I/O retry for spinup notify,
but that shouldn't impact anything other than the failing case"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
scsi: virtio_scsi: Add validation for residual bytes from response
scsi: ipr: System crashes when seeing type 20 error
scsi: core: Retry I/O for Notify (Enable Spinup) Required error
scsi: mpi3mr: Fix warnings reported by smatch
scsi: qedf: Add check to synchronize abort and flush
scsi: MAINTAINERS: Add mpi3mr driver maintainers
scsi: libfc: Fix array index out of bound exception
scsi: mvsas: Use DEVICE_ATTR_RO()/RW() macro
scsi: megaraid_mbox: Use DEVICE_ATTR_ADMIN_RO() macro
scsi: qedf: Use DEVICE_ATTR_RO() macro
scsi: qedi: Use DEVICE_ATTR_RO() macro
scsi: message: mptfc: Switch from pci_ to dma_ API
scsi: be2iscsi: Fix some missing space in some messages
scsi: be2iscsi: Fix an error handling path in beiscsi_dev_probe()
scsi: ufs: Fix build warning without CONFIG_PM
scsi: bnx2fc: Remove meaningless bnx2fc_abts_cleanup() return value assignment
scsi: qla2xxx: Add heartbeat check
scsi: virtio_scsi: Do not overwrite SCSI status
scsi: libsas: Add LUN number check in .slave_alloc callback
scsi: core: Inline scsi_mq_alloc_queue()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Mostly documentation/comment changes and non urgent fixes.
- add or fix SPDX identifiers
- NXP pcf*: fix datasheet URLs
- imxdi: add wakeup support
- pcf2127: handle timestamp interrupts, this fixes a possible
interrupt storm
- bd70528: Drop BD70528 support"
* tag 'rtc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (33 commits)
rtc: pcf8523: rename register and bit defines
rtc: pcf2127: handle timestamp interrupts
rtc: at91sam9: Remove unnecessary offset variable checks
rtc: s5m: Check return value of s5m_check_peding_alarm_interrupt()
rtc: spear: convert to SPDX identifier
rtc: tps6586x: convert to SPDX identifier
rtc: tps80031: convert to SPDX identifier
rtc: rtd119x: Fix format of SPDX identifier
rtc: sc27xx: Fix format of SPDX identifier
rtc: palmas: convert to SPDX identifier
rtc: max6900: convert to SPDX identifier
rtc: ds1374: convert to SPDX identifier
rtc: au1xxx: convert to SPDX identifier
rtc: pcf85063: Update the PCF85063A datasheet revision
dt-bindings: rtc: ti,bq32k: take maintainership
rtc: pcf8563: Fix the datasheet URL
rtc: pcf85063: Fix the datasheet URL
rtc: pcf2127: Fix the datasheet URL
dt-bindings: rtc: ti,bq32k: Convert to json-schema
dt-bindings: rtc: rx8900: Convert to YAML schema
...
|
|
arch/arm/mach-ixp4xx/include/mach/platform.h now gets included indirectly
and defines REG_OFFSET. Rename the register and bit definition to something
specific to the driver.
Fixes: 7fd70c65faac ("ARM: irqstat: Get rid of duplicated declaration")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210710211431.1393589-1-alexandre.belloni@bootlin.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fix from Bjorn Helgaas:
"Revert host bridge window patch that fixed HP EliteDesk 805 G6, but
broke ppc:sam460ex (Bjorn Helgaas)"
* tag 'pci-v5.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Coalesce host bridge contiguous apertures"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
- two small fixes to the svc driver
* tag 'i3c/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: svc: fix doc warning in svc-i3c-master.c
i3c: master: svc: drop free_irq of devm_request_irq allocated irq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add rk3568 sensor support (Finley Xiao)
- Add missing MODULE_DEVICE_TABLE for the Spreadtrum sensor (Chunyan
Zhang)
- Export additionnal attributes for the int340x thermal processor
(Srinivas Pandruvada)
- Add SC7280 compatible for the tsens driver (Rajeshwari Ravindra
Kamble)
- Fix kernel documentation for thermal_zone_device_unregister() and use
devm_platform_get_and_ioremap_resource() (Yang Yingliang)
- Fix coefficient calculations for the rcar_gen3 sensor driver (Niklas
Söderlund)
- Fix shadowing variable rcar_gen3_ths_tj_1 (Geert Uytterhoeven)
- Add missing of_node_put() for the iMX and Spreadtrum sensors
(Krzysztof Kozlowski)
- Add tegra3 thermal sensor DT bindings (Dmitry Osipenko)
- Stop the thermal zone monitoring when unregistering it to prevent a
temperature update without the 'get_temp' callback (Dmitry Osipenko)
- Add rk3568 DT bindings, convert bindings to yaml schemas and add the
corresponding compatible in the Rockchip sensor (Ezequiel Garcia)
- Add the sc8180x compatible for the Qualcomm tsensor (Bjorn Andersson)
- Use the find_first_zero_bit() function instead of custom code (Andy
Shevchenko)
- Fix the kernel doc for the device cooling device (Yang Li)
- Reorg the processor thermal int340x to set the scene for the PCI mmio
driver (Srinivas Pandruvada)
- Add PCI MMIO driver for the int340x processor thermal driver
(Srinivas Pandruvada)
- Add hwmon sensors for the mediatek sensor (Frank Wunderlich)
- Fix warning for return value reported by Smatch for the int340x
thermal processor (Srinivas Pandruvada)
- Fix wrong register access and decoding for the int340x thermal
processor (Srinivas Pandruvada)
* tag 'thermal-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (23 commits)
thermal/drivers/int340x/processor_thermal: Fix tcc setting
thermal/drivers/int340x/processor_thermal: Fix warning for return value
thermal/drivers/mediatek: Add sensors-support
thermal/drivers/int340x/processor_thermal: Add PCI MMIO based thermal driver
thermal/drivers/int340x/processor_thermal: Split enumeration and processing part
thermal: devfreq_cooling: Fix kernel-doc
thermal/drivers/intel/intel_soc_dts_iosf: Switch to use find_first_zero_bit()
dt-bindings: thermal: tsens: Add sc8180x compatible
dt-bindings: rockchip-thermal: Support the RK3568 SoC compatible
dt-bindings: thermal: convert rockchip-thermal to json-schema
thermal/core/thermal_of: Stop zone device before unregistering it
dt-bindings: thermal: Add binding for Tegra30 thermal sensor
thermal/drivers/sprd: Add missing of_node_put for loop iteration
thermal/drivers/imx_sc: Add missing of_node_put for loop iteration
thermal/drivers/rcar_gen3_thermal: Do not shadow rcar_gen3_ths_tj_1
thermal/drivers/rcar_gen3_thermal: Fix coefficient calculations
thermal/drivers/st: Use devm_platform_get_and_ioremap_resource()
thermal/core: Correct function name thermal_zone_device_unregister()
dt-bindings: thermal: tsens: Add compatible string to TSENS binding for SC7280
thermal/drivers/int340x: processor_thermal: Export additional attributes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Fix preempt_count initialization.
- Rework call_on_stack() macro to add proper type handling and avoid
possible register corruption.
- More error prone "register asm" removal and fixes.
- Fix syscall restarting when multiple signals are coming in. This adds
minimalistic trampolines to vdso so we can return from signal without
using the stack which requires pgm check handler hacks when NX is
enabled.
- Remove HAVE_IRQ_EXIT_ON_IRQ_STACK since this is no longer true after
switch to generic entry.
- Fix protected virtualization secure storage access exception
handling.
- Make machine check C handler always enter with DAT enabled and move
register validation to C code.
- Fix tinyconfig boot problem by avoiding MONITOR CALL without
CONFIG_BUG.
- Increase asm symbols alignment to 16 to make it consistent with
compilers.
- Enable concurrent access to the CPU Measurement Counter Facility.
- Add support for dynamic AP bus size limit and rework ap_dqap to deal
with messages greater than recv buffer.
* tag 's390-5.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits)
s390: preempt: Fix preempt_count initialization
s390/linkage: increase asm symbols alignment to 16
s390: rename CALL_ON_STACK_NORETURN() to call_on_stack_noreturn()
s390: add type checking to CALL_ON_STACK_NORETURN() macro
s390: remove old CALL_ON_STACK() macro
s390/softirq: use call_on_stack() macro
s390/lib: use call_on_stack() macro
s390/smp: use call_on_stack() macro
s390/kexec: use call_on_stack() macro
s390/irq: use call_on_stack() macro
s390/mm: use call_on_stack() macro
s390: introduce proper type handling call_on_stack() macro
s390/irq: simplify on_async_stack()
s390/irq: inline do_softirq_own_stack()
s390/irq: simplify do_softirq_own_stack()
s390/ap: get rid of register asm in ap_dqap()
s390: rename PIF_SYSCALL_RESTART to PIF_EXECVE_PGSTE_RESTART
s390: move restart of execve() syscall
s390/signal: remove sigreturn on stack
s390/signal: switch to using vdso for sigreturn and syscall restart
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Olof Johansson:
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller driver
cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining management
interfaces and communication (including bus model) between partitions
both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal with
identity mappings at boot and integration with ARM SMMU pieces.
* tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (120 commits)
firmware: turris-mox-rwtm: add marvell,armada-3700-rwtm-firmware compatible string
firmware: turris-mox-rwtm: show message about HWRNG registration
firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng
firmware: turris-mox-rwtm: report failures better
firmware: turris-mox-rwtm: fix reply status decoding function
soc: imx: gpcv2: add support for i.MX8MN power domains
dt-bindings: add defines for i.MX8MN power domains
firmware: tegra: bpmp: Fix Tegra234-only builds
iommu/arm-smmu: Use Tegra implementation on Tegra186
iommu/arm-smmu: tegra: Implement SID override programming
iommu/arm-smmu: tegra: Detect number of instances at runtime
dt-bindings: arm-smmu: Add Tegra186 compatible string
firmware: qcom_scm: Add MDM9607 compatible
soc: qcom: rpmpd: Add MDM9607 RPM Power Domains
soc: renesas: Add support to read LSI DEVID register of RZ/G2{L,LC} SoC's
soc: renesas: Add ARCH_R9A07G044 for the new RZ/G2L SoC's
dt-bindings: soc: rockchip: drop unnecessary #phy-cells from grf.yaml
memory: emif: remove unused frequency and voltage notifiers
memory: fsl_ifc: fix leak of private memory on probe failure
memory: fsl_ifc: fix leak of IO mapping on probe failure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
|
|
commit 03623b4b041c ("rtc: pcf2127: add tamper detection support")
added support for timestamp interrupts. However they are not being
handled in the irq handler. If a timestamp interrupt occurs it
results in kernel disabling the interrupt and displaying the call
trace:
[ 121.145580] irq 78: nobody cared (try booting with the "irqpoll" option)
...
[ 121.238087] [<00000000c4d69393>] irq_default_primary_handler threaded [<000000000a90d25b>] pcf2127_rtc_irq [rtc_pcf2127]
[ 121.248971] Disabling IRQ #78
Handle timestamp interrupts in pcf2127_rtc_irq(). Save time stamp
before clearing TSF1 and TSF2 flags so that it can't be overwritten.
Set a flag to mark if the timestamp is valid and only report to sysfs
if the flag is set. To mimic the hardware behavior, don’t save
another timestamp until the first one has been read by the userspace.
However, if the alarm irq is not configured, keep the old way of
handling timestamp interrupt in the timestamp0 sysfs calls.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210629150643.31551-1-ykaukab@suse.de
|
|
The offset variable is checked by at91_rtc_readalarm(), but this check
is unnecessary because the previous check knew that the value of this
variable was not 0.
This removes that unnecessary offset variable checks.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210708051340.341345-1-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
s5m_check_peding_alarm_interrupt() in s5m_rtc_read_alarm() gets the return
value, but doesn't use it.
This modifies using the s5m_check_peding_alarm_interrupt()"s return value
as the s5m_rtc_read_alarm()'s return value.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210708051304.341278-1-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-11-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-9-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-8-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
For C files, use the C99 format (//).
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-7-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
For C files, use the C99 format (//).
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-6-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-5-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-4-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-3-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210707075804.337458-2-nobuhiro1.iwamatsu@toshiba.co.jp
|
|
This reverts commit 65db04053efea3f3e412a7e0cc599962999c96b4.
Guenter reported that after 65db04053efe, the ppc:sam460ex qemu emulation
no longer boots from nvme:
nvme nvme0: Device not ready; aborting initialisation, CSTS=0x0
nvme nvme0: Removing after probe failure status: -19
Link: https://lore.kernel.org/r/20210709231529.GA3270116@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After updating the datasheet URL, the PCF85063A datasheet revision
has changed.
Adjust it accordingly.
Reported-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210624120953.2313378-1-festevam@gmail.com
|
|
Pull more block updates from Jens Axboe:
"A combination of changes that ended up depending on both the driver
and core branch (and/or the IDE removal), and a few late arriving
fixes. In detail:
- Fix io ticks wrap-around issue (Chunguang)
- nvme-tcp sock locking fix (Maurizio)
- s390-dasd fixes (Kees, Christoph)
- blk_execute_rq polling support (Keith)
- blk-cgroup RCU iteration fix (Yu)
- nbd backend ID addition (Prasanna)
- Partition deletion fix (Yufen)
- Use blk_mq_alloc_disk for mmc, mtip32xx, ubd (Christoph)
- Removal of now dead block request types due to IDE removal
(Christoph)
- Loop probing and control device cleanups (Christoph)
- Device uevent fix (Christoph)
- Misc cleanups/fixes (Tetsuo, Christoph)"
* tag 'block-5.14-2021-07-08' of git://git.kernel.dk/linux-block: (34 commits)
blk-cgroup: prevent rcu_sched detected stalls warnings while iterating blkgs
block: fix the problem of io_ticks becoming smaller
nvme-tcp: can't set sk_user_data without write_lock
loop: remove unused variable in loop_set_status()
block: remove the bdgrab in blk_drop_partitions
block: grab a device refcount in disk_uevent
s390/dasd: Avoid field over-reading memcpy()
dasd: unexport dasd_set_target_state
block: check disk exist before trying to add partition
ubd: remove dead code in ubd_setup_common
nvme: use return value from blk_execute_rq()
block: return errors from blk_execute_rq()
nvme: use blk_execute_rq() for passthrough commands
block: support polling through blk_execute_rq
block: remove REQ_OP_SCSI_{IN,OUT}
block: mark blk_mq_init_queue_data static
loop: rewrite loop_exit using idr_for_each_entry
loop: split loop_lookup
loop: don't allow deleting an unspecified loop device
loop: move loop_ctl_mutex locking into loop_add
...
|
|
Pull virtio,vhost,vdpa updates from Michael Tsirkin:
- Doorbell remapping for ifcvf, mlx5
- virtio_vdpa support for mlx5
- Validate device input in several drivers (for SEV and friends)
- ZONE_MOVABLE aware handling in virtio-mem
- Misc fixes, cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-mem: prioritize unplug from ZONE_MOVABLE in Big Block Mode
virtio-mem: simplify high-level unplug handling in Big Block Mode
virtio-mem: prioritize unplug from ZONE_MOVABLE in Sub Block Mode
virtio-mem: simplify high-level unplug handling in Sub Block Mode
virtio-mem: simplify high-level plug handling in Sub Block Mode
virtio-mem: use page_zonenum() in virtio_mem_fake_offline()
virtio-mem: don't read big block size in Sub Block Mode
virtio/vdpa: clear the virtqueue state during probe
vp_vdpa: allow set vq state to initial state after reset
virtio-pci library: introduce vp_modern_get_driver_features()
vdpa: support packed virtqueue for set/get_vq_state()
virtio-ring: store DMA metadata in desc_extra for split virtqueue
virtio: use err label in __vring_new_virtqueue()
virtio_ring: introduce virtqueue_desc_add_split()
virtio_ring: secure handling of mapping errors
virtio-ring: factor out desc_extra allocation
virtio_ring: rename vring_desc_extra_packed
virtio-ring: maintain next in extra state for packed virtqueue
vdpa/mlx5: Clear vq ready indication upon device reset
vdpa/mlx5: Add support for doorbell bypassing
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Regression fix in drbg due to missing self-test for new default
algorithm
- Add ratelimit on user-triggerable message in qat
- Fix build failure due to missing dependency in sl3516
- Remove obsolete PageSlab checks
- Fix bogus hardware register writes on Kunpeng920 in hisilicon/sec
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hisilicon/sec - fix the process of disabling sva prefetching
crypto: sl3516 - Add dependency on ARCH_GEMINI
crypto: sl3516 - Typo s/Stormlink/Storlink/
crypto: drbg - self test for HMAC(SHA-512)
crypto: omap - Drop obsolete PageSlab check
crypto: scatterwalk - Remove obsolete PageSlab check
crypto: qat - ratelimit invalid ioctl message and print the invalid cmd
|
|
Merging in the last batch of fixes that didn't go in before previous
release, just a few smaller DT fixups and a MAINTAINERS update
* arm/fixes: (29 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ARM: dts: ux500: Fix LED probing
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
arm64: dts: allwinner: a64-sopine-baseboard: change RGMII mode to TXID
arm64: meson: select COMMON_CLK
soc: amlogic: meson-clk-measure: remove redundant dev_err call in meson_msr_probe()
ARM: dts: qcom: sdx55-telit: Represent secure-regions as 64-bit elements
ARM: dts: qcom: sdx55-t55: Represent secure-regions as 64-bit elements
ARM: dts: sun8i: h3: orangepi-plus: Fix ethernet phy-mode
ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cells
ARM: dts: imx7d-pico: Fix the 'tuning-step' property
ARM: dts: imx7d-meerkat96: Fix the 'tuning-step' property
arm64: dts: freescale: sl28: var1: fix RGMII clock and voltage
arm64: dts: freescale: sl28: var4: fix RGMII clock and voltage
ARM: imx: pm-imx27: Include "common.h"
arm64: dts: zii-ultra: fix 12V_MAIN voltage
arm64: dts: zii-ultra: remove second GEN_3V3 regulator instance
arm64: dts: ls1028a: fix memory node
optee: use export_uuid() to copy client UUID
arm64: dts: ti: k3*: Introduce reg definition for interrupt routers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
- Support for optimized routines based on the host CPU
- Support for PCI via virtio
- Various fixes
* tag 'for-linus-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: remove unneeded semicolon in um_arch.c
um: Remove the repeated declaration
um: fix error return code in winch_tramp()
um: fix error return code in slip_open()
um: Fix stack pointer alignment
um: implement flush_cache_vmap/flush_cache_vunmap
um: add a UML specific futex implementation
um: enable the use of optimized xor routines in UML
um: Add support for host CPU flags and alignment
um: allow not setting extra rpaths in the linux binary
um: virtio/pci: enable suspend/resume
um: add PCI over virtio emulation driver
um: irqs: allow invoking time-travel handler multiple times
um: time-travel/signals: fix ndelay() in interrupt
um: expose time-travel mode to userspace side
um: export signals_enabled directly
um: remove unused smp_sigio_handler() declaration
lib: add iomem emulation (logic_iomem)
um: allow disabling NO_IOMEM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBIFS updates from Richard Weinberger:
- Fix for a race xattr list and modification
- Various minor fixes (spelling, return codes, ...)
* tag 'for-linus-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: Set/Clear I_LINKABLE under i_lock for whiteout inode
ubifs: Fix spelling mistakes
ubifs: Remove ui_mutex in ubifs_xattr_get and change_xattr
ubifs: Fix races between xattr_{set|get} and listxattr operations
ubifs: fix snprintf() checking
ubifs: journal: Fix error return code in ubifs_jnl_write_inode()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix a MIPS bug where irqdomain loopkups could occur in a context
where RCU is not allowed
- Fix a documentation bug for handle_domain_irq
|
|
Since d4a45c68dc81 ("irqdomain: Protect the linear revmap with RCU"),
any irqdomain lookup requires the RCU read lock to be held.
This assumes that the architecture code will be structured such as
irq_enter() will be called *before* the interrupt is looked up
in the irq domain. However, this isn't the case for MIPS, and a number
of drivers are structured to do it the other way around when handling
an interrupt in their root irqchip (secondary irqchips are OK by
construction).
This results in a RCU splat on a lockdep-enabled kernel when the kernel
takes an interrupt from idle, as reported by Guenter Roeck.
Note that this could have fired previously if any driver had used
tree-based irqdomain, which always had the RCU requirement.
To solve this, provide a MIPS-specific helper (do_domain_IRQ())
as the pendent of do_IRQ() that will do thing in the right order
(and maybe save some cycles in the process).
Ideally, MIPS would be moved over to using handle_domain_irq(),
but that's much more ambitious.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[maz: add dependency on CONFIG_IRQ_DOMAIN after report from the kernelci bot]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20210705172352.GA56304@roeck-us.net
Link: https://lore.kernel.org/r/20210706110647.3979002-1-maz@kernel.org
|
|
Pull drm fixes from Dave Airlie:
"Some fixes for rc1 that came in the past weeks, mainly a bunch of
amdgpu fixes, some i915 and the rest are misc around the place. I'm
sending this a bit early so some more stuff may show up, but I'll
probably take tomorrow off.
dma-buf:
- doc fixes
amdgpu:
- Misc Navi fixes
- Powergating fix
- Yellow Carp updates
- Beige Goby updates
- S0ix fix
- Revert overlay validation fix
- GPU reset fix for DC
- PPC64 fix
- Add new dimgrey cavefish DID
- RAS fix
- TTM fixes
amdkfd:
- SVM fixes
radeon:
- Fix missing drm_gem_object_put in error path
- NULL ptr deref fix
i915:
- display DP VSC fix
- DG1 display fix
- IRQ fixes
- IRQ demidlayering
gma500:
- bo leaks in error paths fixed"
* tag 'drm-next-2021-07-08-1' of git://anongit.freedesktop.org/drm/drm: (52 commits)
drm/i915: Drop all references to DRM IRQ midlayer
drm/i915: Use the correct IRQ during resume
drm/i915/display/dg1: Correctly map DPLLs during state readout
drm/i915/display: Do not zero past infoframes.vsc
drm/amdgpu: Conditionally reset SDMA RAS error counts
drm/amdkfd: Maintain svm_bo reference in page->zone_device_data
drm/amdkfd: add invalid pages debug at vram migration
drm/amdkfd: skip migration for pages already in VRAM
drm/amdkfd: skip invalid pages during migrations
drm/amdkfd: classify and map mixed svm range pages in GPU
drm/amdkfd: use hmm range fault to get both domain pfns
drm/amdgpu: get owner ref in validate and map
drm/amdkfd: set owner ref to svm range prefault
drm/amdkfd: add owner ref param to get hmm pages
drm/amdkfd: device pgmap owner at the svm migrate init
drm/amdkfd: inc counter on child ranges with xnack off
drm/amd/display: Extend DMUB diagnostic logging to DCN3.1
drm/amdgpu: Update NV SIMD-per-CU to 2
drm/amdgpu: add new dimgrey cavefish DID
drm/amd/pm: skip PrepareMp1ForUnload message in s0ix
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains mostly various fixes, cleanups and some conversions to
the atomic API. One noteworthy change is that PWM consumers can now
pass a hint to the PWM core about the PWM usage, enabling PWM
providers to implement various optimizations.
There's also a fair bit of simplification here with the addition of
some device-managed helpers as well as unification between the DT and
ACPI firmware interfaces"
* tag 'pwm/for-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (50 commits)
pwm: Remove redundant assignment to pointer pwm
pwm: ep93xx: Fix read of uninitialized variable ret
pwm: ep93xx: Prepare clock before using it
pwm: ep93xx: Unfold legacy callbacks into ep93xx_pwm_apply()
pwm: ep93xx: Implement .apply callback
pwm: vt8500: Only unprepare the clock after the pwmchip was removed
pwm: vt8500: Drop if with an always false condition
pwm: tegra: Assert reset only after the PWM was unregistered
pwm: tegra: Don't needlessly enable and disable the clock in .remove()
pwm: tegra: Don't modify HW state in .remove callback
pwm: tegra: Drop an if block with an always false condition
pwm: core: Simplify some devm_*pwm*() functions
pwm: core: Remove unused devm_pwm_put()
pwm: core: Unify fwnode checks in the module
pwm: core: Reuse fwnode_to_pwmchip() in ACPI case
pwm: core: Convert to use fwnode for matching
docs: firmware-guide: ACPI: Add a PWM example
dt-bindings: pwm: pwm-tiecap: Add compatible string for AM64 SoC
dt-bindings: pwm: pwm-tiecap: Convert to json schema
pwm: sprd: Don't check the return code of pwmchip_remove()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
- A handful of fixes for lmk04832 driver
- Migrate the basic clk divider to use determine rate ops
- Fix modpost build for hisilicon hi3559a driver
- Actually set the parent in k210_clk_set_parent()
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: divider: Switch from .round_rate to .determine_rate by default"
clk: hisilicon: hi3559a: Drop __init markings everywhere
clk: meson: regmap: switch to determine_rate for the dividers
clk: divider: Switch from .round_rate to .determine_rate by default
clk: divider: Add re-usable determine_rate implementations
clk: k210: Fix k210_clk_set_parent()
clk: lmk04832: Fix spelling mistakes in dev_err messages and comments
clk: lmk04832: fix return value check in lmk04832_probe()
clk: stm32mp1: fix missing spin_lock_init()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Fix dsm_label_utf16s_to_utf8s() buffer overrun (Krzysztof
Wilczyński)
- Rely on lengths from scnprintf(), dsm_label_utf16s_to_utf8s()
(Krzysztof Wilczyński)
- Use sysfs_emit() and sysfs_emit_at() in "show" functions (Krzysztof
Wilczyński)
- Fix 'resource_alignment' newline issues (Krzysztof Wilczyński)
- Add 'devspec' newline (Krzysztof Wilczyński)
- Dynamically map ECAM regions (Russell King)
Resource management:
- Coalesce host bridge contiguous apertures (Kai-Heng Feng)
PCIe native device hotplug:
- Ignore Link Down/Up caused by DPC (Lukas Wunner)
Power management:
- Leave Apple Thunderbolt controllers on for s2idle or standby
(Konstantin Kharlamov)
Virtualization:
- Work around Huawei Intelligent NIC VF FLR erratum (Chiqijun)
- Clarify error message for unbound IOV devices (Moritz Fischer)
- Add pci_reset_bus_function() Secondary Bus Reset interface (Raphael
Norwitz)
Peer-to-peer DMA:
- Simplify distance calculation (Christoph Hellwig)
- Finish RCU conversion of pdev->p2pdma (Eric Dumazet)
- Rename upstream_bridge_distance() and rework doc (Logan Gunthorpe)
- Collect acs list in stack buffer to avoid sleeping (Logan
Gunthorpe)
- Use correct calc_map_type_and_dist() return type (Logan Gunthorpe)
- Warn if host bridge not in whitelist (Logan Gunthorpe)
- Refactor pci_p2pdma_map_type() (Logan Gunthorpe)
- Avoid pci_get_slot(), which may sleep (Logan Gunthorpe)
Altera PCIe controller driver:
- Add Joyce Ooi as Altera PCIe maintainer (Joyce Ooi)
Broadcom iProc PCIe controller driver:
- Fix multi-MSI base vector number allocation (Sandor Bodo-Merle)
- Support multi-MSI only on uniprocessor kernel (Sandor Bodo-Merle)
Freescale i.MX6 PCIe controller driver:
- Limit DBI register length for imx6qp PCIe (Richard Zhu)
- Add "vph-supply" for PHY supply voltage (Richard Zhu)
- Enable PHY internal regulator when supplied >3V (Richard Zhu)
- Remove imx6_pcie_probe() redundant error message (Zhen Lei)
Intel Gateway PCIe controller driver:
- Fix INTx enable (Martin Blumenstingl)
Marvell Aardvark PCIe controller driver:
- Fix checking for PIO Non-posted Request (Pali Rohár)
- Implement workaround for the readback value of VEND_ID (Pali Rohár)
MediaTek PCIe controller driver:
- Remove redundant error printing in mtk_pcie_subsys_powerup() (Zhen
Lei)
MediaTek PCIe Gen3 controller driver:
- Add missing MODULE_DEVICE_TABLE (Zou Wei)
Microchip PolarFlare PCIe controller driver:
- Make struct event_descs static (Krzysztof Wilczyński)
Microsoft Hyper-V host bridge driver:
- Fix race condition when removing the device (Long Li)
- Remove bus device removal unused refcount/functions (Long Li)
Mobiveil PCIe controller driver:
- Remove unused readl and writel functions (Krzysztof Wilczyński)
NVIDIA Tegra PCIe controller driver:
- Add missing MODULE_DEVICE_TABLE (Zou Wei)
NVIDIA Tegra194 PCIe controller driver:
- Fix tegra_pcie_ep_raise_msi_irq() ill-defined shift (Jon Hunter)
- Fix host initialization during resume (Vidya Sagar)
Rockchip PCIe controller driver:
- Register IRQ handlers after device and data are ready (Javier
Martinez Canillas)"
* tag 'pci-v5.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI/P2PDMA: Finish RCU conversion of pdev->p2pdma
PCI: xgene: Annotate __iomem pointer
PCI: Fix kernel-doc formatting
PCI: cpcihp: Declare cpci_debug in header file
MAINTAINERS: Add Joyce Ooi as Altera PCIe maintainer
PCI: rockchip: Register IRQ handlers after device and data are ready
PCI: tegra194: Fix tegra_pcie_ep_raise_msi_irq() ill-defined shift
PCI: aardvark: Implement workaround for the readback value of VEND_ID
PCI: aardvark: Fix checking for PIO Non-posted Request
PCI: tegra194: Fix host initialization during resume
PCI: tegra: Add missing MODULE_DEVICE_TABLE
PCI: imx6: Enable PHY internal regulator when supplied >3V
dt-bindings: imx6q-pcie: Add "vph-supply" for PHY supply voltage
PCI: imx6: Limit DBI register length for imx6qp PCIe
PCI: imx6: Remove imx6_pcie_probe() redundant error message
PCI: intel-gw: Fix INTx enable
PCI: iproc: Support multi-MSI only on uniprocessor kernel
PCI: iproc: Fix multi-MSI base vector number allocation
PCI: mediatek-gen3: Add missing MODULE_DEVICE_TABLE
PCI: Dynamically map ECAM regions
...
|
|
Rework of the ap_dqap() inline function with the dqap inline assembler
invocation and the caller code in ap_queue.c to be able to handle
replies which exceed the receive buffer size.
ap_dqap() now provides two additional parameters to handle together
with the caller the case where a reply in the firmware queue entry
exceeds the given message buffer size. It depends on the caller how to
exactly handle this. The behavior implemented now by ap_sm_recv() in
ap_queue.c is to simple purge this entry from the firmware queue and
let the caller 'receive' a -EMSGSIZE for the request without
delivering any reply data - not even a truncated reply message.
However, the reworked ap_dqap() could now get invoked in a way that
the message is received in multiple parts and the caller assembles the
parts into one reply message.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Suggested-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Let's handle unplug in Big Block Mode similar to Sub Block Mode --
prioritize memory blocks onlined to ZONE_MOVABLE.
We won't care further about big blocks with mixed zones, as it's
rather a corner case that won't matter in practice.
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-8-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Let's simplify high-level big block selection when unplugging in
Big Block Mode.
Combine handling of offline and online blocks. We can get rid of
virtio_mem_bbm_bb_is_offline() and simply use
virtio_mem_bbm_offline_remove_and_unplug_bb(), as that already tolerates
offline parts.
We can race with concurrent onlining/offlining either way, so we don;t
have to be super correct by failing if an offline big block we'd like to
unplug just got (partially) onlined.
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-7-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Until now, memory provided by a single virtio-mem device was usually
either onlined completely to ZONE_MOVABLE (online_movable) or to
ZONE_NORMAL (online_kernel); however, that will change in the future.
There are two reasons why we want to track to which zone a memory blocks
belongs to and prioritize ZONE_MOVABLE blocks:
1) Memory managed by ZONE_MOVABLE can more likely get unplugged, therefore,
resulting in a faster memory hotunplug process. Further, we can more
reliably unplug and remove complete memory blocks, removing metadata
allocated for the whole memory block.
2) We want to avoid corner cases where unplugging with the current scheme
(highest to lowest address) could result in accidential zone imbalances,
whereby we remove too much ZONE_NORMAL memory for ZONE_MOVABLE memory
of the same device.
Let's track the zone via memory block states and try unplug from
ZONE_MOVABLE first. Rename VIRTIO_MEM_SBM_MB_ONLINE* to
VIRTIO_MEM_SBM_MB_KERNEL* to avoid even longer state names.
In commit 27f852795a06 ("virtio-mem: don't special-case ZONE_MOVABLE"),
we removed slightly similar tracking for fully plugged memory blocks to
support unplugging from ZONE_MOVABLE at all -- as we didn't allow partially
plugged memory blocks in ZONE_MOVABLE before that. That commit already
mentioned "In the future, we might want to remember the zone again and use
the information when (un)plugging memory."
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-6-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Let's simplify by introducing a new virtio_mem_sbm_unplug_any_sb(),
similar to virtio_mem_sbm_plug_any_sb(), to simplify high-level memory
block selection when unplugging in Sub Block Mode.
Rename existing virtio_mem_sbm_unplug_any_sb() to
virtio_mem_sbm_unplug_any_sb_raw().
The only change is that we now temporarily unlock the hotplug mutex around
cond_resched() when processing offline memory blocks, which doesn't
make a real difference as we already have to temporarily unlock in
virtio_mem_sbm_unplug_any_sb_offline() when removing a memory block.
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-5-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Let's simplify high-level memory block selection when plugging in Sub
Block Mode.
No need for two separate loops when selecting memory blocks for plugging
memory. Avoid passing the "online" state by simply obtaining the state
in virtio_mem_sbm_plug_any_sb().
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-4-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Let's use page_zonenum() instead of zone_idx(page_zone()).
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-3-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We are reading a Big Block Mode value while in Sub Block Mode
when initializing. Fortunately, vm->bbm.bb_size maps to some counter
in the vm->sbm.mb_count array, which is 0 at that point in time.
No harm done; still, this was unintended and is not future-proof.
Fixes: 4ba50cd3355d ("virtio-mem: Big Block Mode (BBM) memory hotplug")
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210602185720.31821-2-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Clear the available index as part of the initialization process to
clear and values that might be left from previous usage of the device.
For example, if the device was previously used by vhost_vdpa and now
probed by vhost_vdpa, you want to start with indices.
Fixes: c043b4a8cf3b ("virtio: introduce a vDPA based transport")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20210602021536.39525-5-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
|
