| Age | Commit message (Collapse) | Author |
|---|
|
This is log is harmful as it can trigger multiple times per packet. Delete
it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets without the last descriptor set should be dropped early. If we
receive a frame larger than the DMA buffer, the HW will continue using the
next descriptor. Driver mistakes these as individual frames, and sometimes
a truncated frame (without the LD set) may look like a valid packet.
This fixes a strange issue where the system replies to 4098-byte ping
although the MTU/DMA buffer size is set to 4096, and yet at the same
time it's logging an oversized packet.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have error bits set, the discard_frame status will get overwritten
by checksum bit checks, which might set the status back to good one.
Fix by checking the COE status only if the frame is good.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if we drop a packet, we exit from NAPI loop before the budget
is consumed. In some situations this will make the RX processing stall
e.g. when flood pinging the system with oversized packets, as the
errorneous packets are not dropped efficiently.
If we drop a packet, we should just continue to the next one as long as
the budget allows.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ratelimit RX error logs.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We always program the maximum DMA buffer size into the receive descriptor,
although the allocated size may be less. E.g. with the default MTU size
we allocate only 1536 bytes. If somebody sends us a bigger frame, then
memory may get corrupted.
Fix by using exact buffer sizes.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was reported that re-introducing ASPM, in combination with RX
interrupt coalescing, results in significantly increased packet
latency, see [0]. Disabling ASPM or RX interrupt coalescing fixes
the issue. Therefore change the driver's default to disable RX
interrupt coalescing. Users still have the option to enable RX
coalescing via ethtool.
[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=925496
Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support")
Reported-by: Mike Crowe <mac@mcrowe.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-03-29
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.11
('net/mlx5: Decrease default mr cache size')
For -stable v4.12
('net/mlx5e: Add a lock on tir list')
For -stable v4.13
('net/mlx5e: Fix error handling when refreshing TIRs')
For -stable v4.18
('net/mlx5e: Update xon formula')
For -stable v4.19
('net: mlx5: Add a missing check on idr_find, free buf')
('net/mlx5e: Update xoff formula')
net-next merge Note:
When merged with net-next the following simple conflict will appear,
drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c
++<<<<<<< HEAD (net)
+ * max_mtu: netdev's max_mtu
++=======
+ * @mtu: device's MTU
++>>>>>>> net-next
To resolve: just replace the line in net-next
* @mtu: device's MTU
to
* @max_mtu: netdev's max_mtu
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 4d31c4fa3f9ef7b7e2e79fd57d21290f64c938f5.
Accidently applied this to the wrong tree.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change t4fw_version.h to update latest firmware version
number to 1.23.3.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After queue stopped, the wakeup mechanism may wake it up again
when ring buffer usage is lower than a threshold. This may cause
send path panic on NULL pointer when we stopped all tx queues in
netvsc_detach and start removing the netvsc device.
This patch fix it by adding a tx_disable flag to prevent unwanted
queue wakeup.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Reported-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bond expects ethernet hwaddr for its slave, but it can be longer than 6
bytes - infiniband interface for example.
# cat /sys/devices/<skipped>/net/ib0/address
80:00:02:08:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:be:5d:e1
# cat /sys/devices/<skipped>/net/ib0/bonding_slave/perm_hwaddr
80:00:02:08:fe:80
So print full hwaddr in sysfs "bonding_slave/perm_hwaddr" as well.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver allocates an encap context based on the tunnel properties,
and reuse that context for all flows using the same tunnel properties.
Commit df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading")
introduced another tunnel protocol other than the single VXLAN
previously supported. A flow that uses a tunnel with the same tunnel
properties but with a different tunnel type (GRE vs VXLAN for example)
would mistakenly reuse the previous alocated context, causing the
traffic to be sent with the wrong encapsulation. Fix that by
considering the tunnel type for encap contexts.
Fixes: df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Set xon = xoff - netdev's max_mtu.
netdev's max_mtu will give enough time for the pause frame to
arrive at the sender.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Set minimum speed in xoff threshold formula to 40Gbps
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Make sure the struct mlx5_flow_destination is zero before
filling in the field.
Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Traditionally, the PF (Physical Function) which resides on vport 0 was
the E-switch manager. Since the ECPF (Embedded CPU Physical Function),
which resides on vport 0xfffe, was introduced as the E-Switch manager,
the assumption that the E-switch manager is on vport 0 is incorrect.
Since the eswitch code already uses the actual vport value, all we
need is to always set other_vport=1.
Signed-off-by: Omri Kahalon <omrik@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The esw offloads structures share a union with the legacy mode structs.
Reset the offloads struct to zero in init to protect from null
assumptions made by the legacy mode code.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The capacity of FDB offloading and NIC offloading table are
different, and when allocating the pedit actions, we should
use the correct namespace type.
Fixes: c500c86b0c75d ("net/mlx5e: support for two independent packet edit actions")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The esw fdb table has a union of legacy and offloads members.
So if we were in a certain esw mode we could set some memebers and not
set null which is fine as on destroy path and don't care.
But then moving from legacy to switchdev a second time, the cleanup flow
of legacy mode checks if a struct member was in use if it's not null so
we need to make sure to reset the code to null when we init legacy mode.
Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow configuration of legacy link-modes even when extended link-modes
are supported. This requires reading of legacy advertisement even when
extended link-modes are supported. Since legacy and extended
advertisement are mutually excluded, wait for empty reply from extended
advertisement before reading legacy advertisement.
Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Ethtool option set_link_ksettings allows setting of legacy link-modes
or extended link-modes. Refine the decision of which type of link-modes
is set.
Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Refresh tirs is looping over a global list of tirs while netdevs are
adding and removing tirs from that list. That is why a lock is
required.
Fixes: 724b2aa15126 ("net/mlx5e: TIRs management refactoring")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
idr_find() can return a NULL value to 'flow' which is used without a
check. The patch adds a check to avoid potential NULL pointer dereference.
In case of mlx5_fpga_sbu_conn_sendmsg() failure, free buf allocated
using kzalloc.
Fixes: ab412e1dd7db ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For some protocols we are not allowing IP header rewrite offload, since
the HW is not capable to properly adjust the l4 checksum. However, TTL
& HOPLIMIT modification can be done for all IP protocols, because they
are not part of the pseudo header taken into account for checksum.
Fixes: 738678817573 ("drivers: net: use flow action infrastructure")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Previously, a false positive would be caught if the TIRs list is
empty, since the err value was initialized to -ENOMEM, and was only
updated if a TIR is refreshed. This is resolved by initializing the
err value to zero.
Fixes: b676f653896a ("net/mlx5e: Refactor refresh TIRs")
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Delete initialization of high order entries in mr cache to decrease initial
memory footprint. When required, the administrator can populate the
entries with memory keys via the /sys interface.
This approach is very helpful to significantly reduce the per HW function
memory footprint in virtualization environments such as SRIOV.
Fixes: 9603b61de1ee ("mlx5: Move pci device handling from mlx5_ib to mlx5_core")
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
NFP reprs are software device on top of the PF's vNIC.
The comment above __dev_queue_xmit() sayeth:
When calling this method, interrupts MUST be enabled. This is because
the BH enable code must have IRQs enabled so that it will not deadlock.
For netconsole we can't guarantee IRQ state, let's just
disable netpoll on representors to be on the safe side.
When the initial implementation of NFP reprs was added by the
commit 5de73ee46704 ("nfp: general representor implementation")
.ndo_poll_controller was required for netpoll to be enabled.
Fixes: ac3d9dd034e5 ("netpoll: make ndo_poll_controller() optional")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_queue_xmit() may return error codes as well as netdev_tx_t,
and it always consumes the skb. Make sure we always return a
correct netdev_tx_t value.
Fixes: eadfa4c3be99 ("nfp: add stats and xmit helpers for representors")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a Qualcomm based device with a QMI function on interface 4.
It is mode switched from 2020:2030 using a standard eject message.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2020 ProdID=2031 Rev= 2.32
S: Manufacturer=Mobile Connect
S: Product=Mobile Connect
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-03-26
This series contains updates to igb, ixgbe, i40e and fm10k.
Jake fixes an issue with PTP in i40e where a previous commit resulted
in a regression where the driver would interpret small negative
adjustments as large positive additions, resulting in incorrect
behavior.
Arvind Sankar fixes an issue in igb where a previous commit would cause
a warning in the PCI pm core and resulted in pci_pm_runtime_suspend
would not call pci_save_state or pci_finish_runtime_suspend.
Ivan Vecera fixes MDIO bus registration with ixgbe, where the driver was
ignoring errors returned when registering and would leave the pointer in
a NULL state which triggered a BUG when un-registering.
Stefan Assmann fixes the check for Wake-On-LAN for i40e, which only
supports magic packet.
Yue Haibing fixes a potential NULL pointer de-reference in fm10k by
adding a simple check if the value is NULL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VRF devices don't work with upper devices. Currently, it's possible to
add a VRF device to a bridge or team, and to create macvlan, macsec, or
ipvlan devices on top of a VRF (bond and vlan are prevented respectively
by the lack of an ndo_set_mac_address op and the NETIF_F_VLAN_CHALLENGED
feature flag).
Fix this by setting the IFF_NO_RX_HANDLER flag (introduced in commit
f5426250a6ec ("net: introduce IFF_NO_RX_HANDLER")).
Cc: David Ahern <dsahern@gmail.com>
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the non-XDP case, commit 773225388dae15e72790 ("net: thunderx: Optimize
page recycling for XDP") added code to nicvf_free_rbdr() that, when releasing
the additional receive buffer page reference held for recycling, repeatedly
calls put_page() until the page's _refcount goes to zero. Which results in
the page being freed.
This is not okay if the page's _refcount was greater than 1 (in the non-XDP
case), because nicvf_free_rbdr() should not be subtracting more than what
nicvf_alloc_page() had previously added to the page's _refcount, which was
only 1 (in the non-XDP case).
This can arise if a received packet is still being processed and the receive
buffer (i.e., skb->head) has not yet been freed via skb_free_head() when
nicvf_free_rbdr() is spinning through the aforementioned put_page() loop.
If this should occur, when the received packet finishes processing and
skb_free_head() is called, various problems can ensue. Exactly what, depends on
whether the page has already been reallocated or not, anything from "BUG: Bad
page state ... ", to "Unable to handle kernel NULL pointer dereference ..." or
"Unable to handle kernel paging request...".
So this patch changes nicvf_free_rbdr() to only call put_page() once for pages
held for recycling (in the non-XDP case).
Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 773225388dae15e72790 ("net: thunderx: Optimize page recycling for XDP")
added code to nicvf_alloc_page() that inadvertently disables receive buffer
page recycling for the non-XDP case by always NULL'ng the page pointer.
This patch corrects two if-conditionals to allow for the recycling of non-XDP
mode pages by only setting the page pointer to NULL when the page is not ready
for recycling.
Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP")
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the rules for configuring search paths in Kbuild have
changed, this will lead some erros when compiling hns3 with the
following command:
make O=DIR M=drivers/net/ethernet/hisilicon/hns3
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:11:10:
fatal error: hnae3.h: No such file or directory
This patch fix it by adding $(srctree)/ prefix to the serach paths.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
|
|
Syzkaller report this:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 0 PID: 4378 Comm: syz-executor.0 Tainted: G C 5.0.0+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:__lock_acquire+0x95b/0x3200 kernel/locking/lockdep.c:3573
Code: 00 0f 85 28 1e 00 00 48 81 c4 08 01 00 00 5b 5d 41 5c 41 5d 41 5e 41 5f c3 4c 89 ea 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 24 00 00 49 81 7d 00 e0 de 03 a6 41 bc 00 00
RSP: 0018:ffff8881e3c07a40 EFLAGS: 00010002
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000010 RSI: 0000000000000000 RDI: 0000000000000080
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8881e3c07d98 R11: ffff8881c7f21f80 R12: 0000000000000001
R13: 0000000000000080 R14: 0000000000000000 R15: 0000000000000001
FS: 00007fce2252e700(0000) GS:ffff8881f2400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fffc7eb0228 CR3: 00000001e5bea002 CR4: 00000000007606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
lock_acquire+0xff/0x2c0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xdf/0x1050 kernel/locking/mutex.c:1072
drain_workqueue+0x24/0x3f0 kernel/workqueue.c:2934
destroy_workqueue+0x23/0x630 kernel/workqueue.c:4319
__do_sys_delete_module kernel/module.c:1018 [inline]
__se_sys_delete_module kernel/module.c:961 [inline]
__x64_sys_delete_module+0x30c/0x480 kernel/module.c:961
do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fce2252dc58 EFLAGS: 00000246 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000140
RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fce2252e6bc
R13: 00000000004bcca9 R14: 00000000006f6b48 R15: 00000000ffffffff
If alloc_workqueue fails, it should return -ENOMEM, otherwise may
trigger this NULL pointer dereference while unloading drivers.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0a38c17a21a0 ("fm10k: Remove create_workqueue")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current check for WoL on i40e is broken. Code comment says only
magic packet is supported, so only check for that.
Fixes: 540a152da762 (i40e/ixgbe/igb: fail on new WoL flag setting WAKE_MAGICSECURE)
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ixgbe ignores errors returned from mdiobus_register() and leaves
adapter->mii_bus non-NULL and MDIO bus state as MDIOBUS_ALLOCATED.
This triggers a BUG from mdiobus_unregister() during ixgbe_remove() call.
Fixes: 8fa10ef01260 ("ixgbe: register a mdiobus")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.
Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.
Also move a couple of defines into the appropriate header file instead
of inline in the .c file.
Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: Arvind Sankar <niveditas98@gmail.com>
Reviewed-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit 0ac30ce43323 ("i40e: fix up 32 bit timespec references",
2017-07-26) claims to be cleaning up references to 32-bit timespecs.
The actual contents of the commit make no sense, as it converts a call
to timespec64_add into timespec64_add_ns. This would seem ok, if (a) the
change was documented in the commit message, and (b) timespec64_add_ns
supported negative numbers.
timespec64_add_ns doesn't work with signed deltas, because the
implementation is based around iter_div_u64_rem. This change resulted in
a regression where i40e_ptp_adjtime would interpret small negative
adjustments as large positive additions, resulting in incorrect
behavior.
This commit doesn't appear to fix anything, is not well explained, and
introduces a bug, so lets just revert it.
Reverts: 0ac30ce43323 ("i40e: fix up 32 bit timespec references", 2017-07-26)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It might happen that Tx conf acknowledges a frame before it was
subscribed in bql, as subscribing was previously done after the enqueue
operation.
This patch moves the netdev_tx_sent_queue call before the actual frame
enqueue, so that this can never happen.
Fixes: 569dac6a5a0d ("dpaa2-eth: bql support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clang warns about possible bugs in a dead code branch after
BUG_ON(1) when CONFIG_PROFILE_ALL_BRANCHES is enabled:
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: error: variable 'buf_size' is used uninitialized whenever 'if'
condition is false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
include/linux/compiler.h:48:23: note: expanded from macro 'unlikely'
# define unlikely(x) (__branch_check__(x, 0, __builtin_constant_p(x)))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:482:9: note: uninitialized use occurs here
return buf_size;
^~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: note: remove the 'if' if its condition is always true
BUG_ON(1);
^
include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^
drivers/net/ethernet/chelsio/cxgb4/sge.c:459:14: note: initialize the variable 'buf_size' to silence this warning
int buf_size;
^
= 0
Use BUG() here to create simpler code that clang understands
correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New device of QNAP based on aqc111u
Add this ID to blacklist of cdc_ether driver as well
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1aec4211204d9463d1fd209eb50453de16254599.
Steven Rostedt reports that it causes a hang at bootup and bisected it
to this commit.
The troigger is apparently a module alias for "parport_lowlevel" that
points to "parport_pc", which causes a hang with
modprobe -q -- parport_lowlevel
blocking forever with a backtrace like this:
wait_for_completion_killable+0x1c/0x28
call_usermodehelper_exec+0xa7/0x108
__request_module+0x351/0x3d8
get_lowlevel_driver+0x28/0x41 [parport]
__parport_register_driver+0x39/0x1f4 [parport]
daisy_drv_init+0x31/0x4f [parport]
parport_bus_init+0x5d/0x7b [parport]
parport_default_proc_register+0x26/0x1000 [parport]
do_one_initcall+0xc2/0x1e0
do_init_module+0x50/0x1d4
load_module+0x1c2e/0x21b3
sys_init_module+0xef/0x117
Supid says:
"Due to the new device model daisy driver will now try to find the
parallel ports while trying to register its driver so that it can bind
with them. Now, since daisy driver is loaded while parport bus is
initialising the list of parport is still empty and it tries to load
the lowlevel driver, which has an alias set to parport_pc, now causes
a deadlock"
But I don't think the daisy driver should be loaded by the parport
initialization in the first place, so let's revert the whole change.
If the daisy driver can just initialize separately on its own (like a
driver should), instead of hooking into the parport init sequence
directly, this issue probably would go away.
Reported-and-bisected-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
