| Age | Commit message (Collapse) | Author |
|---|
|
The ltc3676 can only support single register read and write operations
so does not benefit from block writes. This means it gets no benefit from
using the rbtree register cache over the maple tree register cache so
convert it to use maple trees instead, it is more modern.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230609-regulator-ltc-maple-v1-2-08c15181f8b2@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ltc3589 can only support single register read and write operations
so does not benefit from block writes. This means it gets no benefit from
using the rbtree register cache over the maple tree register cache so
convert it to use maple trees instead, it is more modern.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230609-regulator-ltc-maple-v1-1-08c15181f8b2@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
regulator_set_ramp_delay_regmap()
With W=1:
drivers/regulator/helpers.c:947: warning: Function parameter or member 'ramp_delay' not described in 'regulator_set_ramp_delay_regmap'
Fix it by documenting the parameter.
Fixes: fb8fee9efdcf ("regulator: Add regmap helper for ramp-delay setting")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1686881298-28333-1-git-send-email-cy_huang@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some of the regulators on the MT6358/MT6366 PMICs have just one linear
voltage range. These are the bulk regulators and VSRAM_* LDOs. Currently
they are modeled with one linear range, but also have their minimum,
maximum, and step voltage described.
Convert them to the linear voltage helpers. These helpers are a bit
simpler, and we can also drop the linear range definitions. Also reflow
the touched lines now that they are shorter.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230609083009.2822259-7-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the MT6358 regulator driver, each regulator is described by a
|struct regulator_desc| wrapped by a |struct mt6358_regulator_info|.
The latter was tied to the regulator device using the config's
driver_data field, which meant that the variables could not be constant.
Since each regulator device has a pointer to its regulator_desc, and
mt6358_regulator_info wraps that, the driver could use container_of()
to retrieve it instead.
Switch to using container_of(), drop tha driver_data setting, and
const-ify all the regulator descriptions.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230609083009.2822259-6-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The *_SSHUB regulators are actually alternate configuration interfaces
for their non *_SSHUB counterparts. They are not separate regulator
outputs. These registers are intended for the companion processor to
use to configure the power rails while the main processor is sleeping.
They are not intended for the main operating system to use.
Since they are not real outputs they shouldn't be modeled separately.
Remove them. Luckily no device tree actually uses them.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230609083009.2822259-5-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The VCN33_BT and VCN33_WIFI regulators are actually the same regulator,
having the same voltage setting and output pin. There are simply two
enable bits that are ORed together to enable the regulator.
Having two regulators representing the same output pin is misleading
from a design matching standpoint, and also error-prone in driver
implementations. If consumers try to set different voltages on either
regulator, the one set later would override the one set before. There
are ways around this, such as chaining them together and having the
downstream one act as a switch. But given there's only one output pin,
such a workaround doesn't match reality.
Remove the VCN33_WIFI regulator. During the probe phase, have the driver
sync the enable status of VCN33_WIFI to VCN33_BT. Also drop the suffix
so that the regulator name matches the pin name in the datasheet.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230609083009.2822259-4-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The previous conversion back to .probe done in commit 964e186547b2
("regulator: Switch i2c drivers back to use .probe()") was done based on
v6.3. Since then two more drivers were added which need to be convert
back in the same way before eventually .probe_new() can be dropped from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230611203559.827168-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Esteban Blanc <eblanc@baylibre.com>:
TPS6594 is a Power Management IC which provides regulators and others
features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.
This series adds support to TI TPS6594 PMIC and its derivatives.
|
|
Merge series from Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>:
A "known issue" during implementation of SE DMA for spi geni driver was
that it does DMA map/unmap internally instead of in spi framework.
Current patches remove this hiccup and also clean up code a bit.
Testing revealed no regressions and results with 1000 iterations of
reading from EC showed no loss of performance.
Results
=======
Before - Iteration 999, min=5.10, max=5.17, avg=5.14, ints=25129
After - Iteration 999, min=5.10, max=5.20, avg=5.15, ints=25153
|
|
The spi geni driver in SE DMA mode, unlike GSI DMA, is not making use of
DMA mapping functionality available in the framework.
The driver does mapping internally which makes dma buffer fields available
in spi_transfer struct superfluous while requiring additional members in
spi_geni_master struct.
Conform to the design by having framework handle map/unmap and do only
DMA transfer in the driver; this also simplifies code a bit.
Fixes: e5f0dfa78ac7 ("spi: spi-geni-qcom: Add support for SE DMA mode")
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/1684325894-30252-3-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
geni_se_rx_init_dma()
The geni_se_xx_dma_prep() interfaces necessarily do DMA mapping before
initiating DMA transfers. This is not suitable for spi where framework
is expected to handle map/unmap.
Expose new interfaces geni_se_xx_init_dma() which do only DMA transfer.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/1684325894-30252-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support for TPS6594 regulators (bucks and LDOs).
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Bucks can be used in single or multiphase mode, depending on PMIC
part number.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Link: https://lore.kernel.org/r/20230522163115.2592883-4-eblanc@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Andre Przywara <andre.przywara@arm.com>:
This patch series adds support for the X-Powers AXP15060 and AXP313a
PMIC, which are general purpose PMICs as seen on different boards with
different SOCs, mostly from Allwinner.
This is mostly a repost of the previous patches, combining both the
AXP313a and AXP15060 series, rebased on top of v6.4-rc3, and omitting
the patches that already got merged.
The first two patches are the successors of the AXP313a v10 post,
the third patch is based on Shengyu's AXP15060 v3 post.
There were no code changes, just some tiny context differences due to
the rebase, plus I added the newly gained tags.
As the DT bindings and the AXP15060 MFD part are already in the tree,
this is just completing support with the MFD part for the AXP313a, and
the regulator support for both PMICs.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Fix open firmware quirks validation so that they don't get applied
wrongly
* tag 'irq_urgent_for_v6.4_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic: Correctly validate OF quirk descriptors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes:
- a regression fix for the verisilicon driver
- uvcvideo: don't expose unsupported video formats to userspace
- camss-video: don't zero subdev format after init
- mediatek: some fixes for 4K decoder formats
- fix a Sphinx build warning (missing doc for client_caps)
- some fixes for imx and atomisp staging drivers
And two CEC core fixes:
- don't set last_initiator if TX in progress
- disable adapter in cec_devnode_unregister"
* tag 'media/v6.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: uvcvideo: Don't expose unsupported formats to userspace
media: v4l2-subdev: Fix missing kerneldoc for client_caps
media: staging: media: imx: initialize hs_settle to avoid warning
media: v4l2-mc: Drop subdev check in v4l2_create_fwnode_links_to_pad()
media: staging: media: atomisp: init high & low vars
media: cec: core: don't set last_initiator if tx in progress
media: cec: core: disable adapter in cec_devnode_unregister
media: mediatek: vcodec: Only apply 4K frame sizes on decoder formats
media: camss: camss-video: Don't zero subdev format again after initialization
media: verisilicon: Additional fix for the crash when opening the driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a bunch of tiny char/misc/other driver fixes for 6.4-rc5 that
resolve a number of reported issues. Included in here are:
- iio driver fixes
- fpga driver fixes
- test_firmware bugfixes
- fastrpc driver tiny bugfixes
- MAINTAINERS file updates for some subsystems
All of these have been in linux-next this past week with no reported
issues"
* tag 'char-misc-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (34 commits)
test_firmware: fix the memory leak of the allocated firmware buffer
test_firmware: fix a memory leak with reqs buffer
test_firmware: prevent race conditions by a correct implementation of locking
firmware_loader: Fix a NULL vs IS_ERR() check
MAINTAINERS: Vaibhav Gupta is the new ipack maintainer
dt-bindings: fpga: replace Ivan Bornyakov maintainership
MAINTAINERS: update Microchip MPF FPGA reviewers
misc: fastrpc: reject new invocations during device removal
misc: fastrpc: return -EPIPE to invocations on device removal
misc: fastrpc: Reassign memory ownership only for remote heap
misc: fastrpc: Pass proper scm arguments for secure map request
iio: imu: inv_icm42600: fix timestamp reset
iio: adc: ad_sigma_delta: Fix IRQ issue by setting IRQ_DISABLE_UNLAZY flag
dt-bindings: iio: adc: renesas,rcar-gyroadc: Fix adi,ad7476 compatible value
iio: dac: mcp4725: Fix i2c_master_send() return value handling
iio: accel: kx022a fix irq getting
iio: bu27034: Ensure reset is written
iio: dac: build ad5758 driver when AD5758 is selected
iio: addac: ad74413: fix resistance input processing
iio: light: vcnl4035: fixed chip ID check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core cacheinfo fixes for 6.4-rc5 that
resolve a number of reported issues with that file. These changes have
been in linux-next this past week with no reported problems"
* tag 'driver-core-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers: base: cacheinfo: Update cpu_map_populated during CPU Hotplug
drivers: base: cacheinfo: Fix shared_cpu_map changes in event of CPU hotplug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty/serial driver fixes for 6.4-rc5 that have all
been in linux-next this past week with no reported problems. Included
in here are:
- 8250_tegra driver bugfix
- fsl uart driver bugfixes
- Kconfig fix for dependancy issue
- dt-bindings fix for the 8250_omap driver"
* tag 'tty-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
dt-bindings: serial: 8250_omap: add rs485-rts-active-high
serial: cpm_uart: Fix a COMPILE_TEST dependency
soc: fsl: cpm1: Fix TSA and QMC dependencies in case of COMPILE_TEST
tty: serial: fsl_lpuart: use UARTCTRL_TXINV to send break instead of UARTCTRL_SBK
serial: 8250_tegra: Fix an error handling path in tegra_uart_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB driver and core fixes for 6.4-rc5. Most of these are
tiny driver fixes, including:
- udc driver bugfix
- f_fs gadget driver bugfix
- cdns3 driver bugfix
- typec bugfixes
But the "big" thing in here is a fix yet-again for how the USB buffers
are handled from userspace when dealing with DMA issues. The changes
were discussed a lot, and tested a lot, on the list, and acked by the
relevant mm maintainers and have been in linux-next all this past week
with no reported problems"
* tag 'usb-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tps6598x: Fix broken polling mode after system suspend/resume
mm: page_table_check: Ensure user pages are not slab pages
mm: page_table_check: Make it dependent on EXCLUSIVE_SYSTEM_RAM
usb: usbfs: Use consistent mmap functions
usb: usbfs: Enforce page requirements for mmap
dt-bindings: usb: snps,dwc3: Fix "snps,hsphy_interface" type
usb: gadget: udc: fix NULL dereference in remove()
usb: gadget: f_fs: Add unbind event before functionfs_unbind
usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five fixes, all in drivers.
The most extensive is the target change to fix the hang in the login
code, which involves changing timers from per login to per connection"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: stex: Fix gcc 13 warnings
scsi: qla2xxx: Fix NULL pointer dereference in target mode
scsi: target: iscsi: Prevent login threads from racing between each other
scsi: target: iscsi: Remove unused transport_timer
scsi: target: iscsi: Fix hang in the iSCSI login code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/linux
Pull LED fix from Johan Hovold:
"Here's a fix for a regression in 6.4-rc1 which broke the backlight on
machines such as the Lenovo ThinkPad X13s"
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/lkml/20230602091928.GR449117@google.com/
* tag 'leds-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/linux:
leds: qcom-lpg: Fix PWM period limits
|
|
The introduction of high resolution PWM support changed the order of the
operations in the calculation of min and max period. The result in both
divisions is in most cases a truncation to 0, which limits the period to
the range of [0, 0].
Both numerators (and denominators) are within 64 bits, so the whole
expression can be put directly into the div64_u64, instead of doing it
partially.
Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Lee Jones <lee@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20230515162604.649203-1-quic_bjorande@quicinc.com
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
With commit 858e8b792d06 ("tpm, tpm_tis: Avoid cache incoherency in test
for interrupts") bit accessor functions are used to access flags in
tpm_tis_data->flags.
However these functions expect bit numbers, while the flags are defined
as bit masks in enum tpm_tis_flag.
Fix this inconsistency by using numbers instead of masks also for the
flags in the enum.
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 858e8b792d06 ("tpm, tpm_tis: Avoid cache incoherency in test for interrupts")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the uvcvideo driver encounters a format descriptor with an unknown
format GUID, it creates a corresponding struct uvc_format instance with
the fcc field set to 0. Since commit 50459f103edf ("media: uvcvideo:
Remove format descriptions"), the driver relies on the V4L2 core to
provide the format description string, which the V4L2 core can't do
without a valid 4CC. This triggers a WARN_ON.
As a format with a zero 4CC can't be selected, it is unusable for
applications. Ignore the format completely without creating a uvc_format
instance, which fixes the warning.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217252
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2180107
Fixes: 50459f103edf ("media: uvcvideo: Remove format descriptions")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Initialize hs_settle to 0 to avoid this compiler warning:
imx8mq-mipi-csi2.c: In function 'imx8mq_mipi_csi_start_stream.part.0':
imx8mq-mipi-csi2.c:91:55: warning: 'hs_settle' may be used uninitialized [-Wmaybe-uninitialized]
91 | #define GPR_CSI2_1_S_PRG_RXHS_SETTLE(x) (((x) & 0x3f) << 2)
| ^~
imx8mq-mipi-csi2.c:357:13: note: 'hs_settle' was declared here
357 | u32 hs_settle;
| ^~~~~~~~~
It's a false positive, but it is too complicated for the compiler to detect that.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
While updating v4l2_create_fwnode_links_to_pad() to accept non-subdev
sinks, the check is_media_entity_v4l2_subdev() was not removed which
prevented the function from being used with non-subdev sinks, Drop the
unnecessary check.
Fixes: bd5a03bc5be8 ("media: Accept non-subdev sinks in v4l2_create_fwnode_links_to_pad()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Pull block fixes from Jens Axboe:
"Just an NVMe pull request with (mostly) KATO fixes, a regression fix
for zoned device revalidation, and a fix for an md raid5 regression"
* tag 'block-6.4-2023-06-02' of git://git.kernel.dk/linux:
nvme: fix the name of Zone Append for verbose logging
nvme: improve handling of long keep alives
nvme: check IO start time when deciding to defer KA
nvme: double KA polling frequency to avoid KATO with TBKAS on
nvme: fix miss command type check
block: fix revalidate performance regression
md/raid5: fix miscalculation of 'end_sector' in raid5_read_one_chunk()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix pwrseq for WILC1000/WILC3000 SDIO card
MMC host:
- vub300: Fix invalid response handling"
* tag 'mmc-v6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: pwrseq: sd8787: Fix WILC CHIP_EN and RESETN toggling order
mmc: vub300: fix invalid response handling
|
|
The AXP15060 is a typical I2C-controlled PMIC, seen on multiple boards
with different default register value. Current driver is tested on
Starfive Visionfive 2.
The RTCLDO is fixed, and cannot even be turned on or off. On top of
that, its voltage is customisable (either 1.8V or 3.3V). We pretend it's
a fixed 1.8V regulator since other AXP driver also do like this. Also,
BSP code ignores this regulator and it's not used according to VF2
schematic.
Describe the AXP15060's voltage settings and switch registers, how the
voltages are encoded, and connect this to the MFD device via its
regulator ID.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Shengyu Qu <wiagn233@outlook.com>
Link: https://lore.kernel.org/r/20230524000012.15028-4-andre.przywara@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP313a is your typical I2C controlled PMIC, although in a lighter
fashion compared to the other X-Powers PMICs: it has only three DCDC
rails, three LDOs, and no battery charging support.
The AXP313a datasheet does not describe a register to change the DCDC
switching frequency, and talks of it being fixed at 3 MHz. Check that
the property allowing to change that frequency is absent from the DT,
and bail out otherwise.
The third LDO, RTCLDO, is fixed, and cannot even be turned on or off,
programmatically. On top of that, its voltage is customisable (either
1.8V or 3.3V), which we cannot describe easily using the existing
regulator wrapper functions. This should be fixed properly, using
regulator-{min,max}-microvolt in the DT, but this requires more changes
to the code. As some other PMICs (AXP2xx, AXP803) seem to paper over the
same problem as well, we follow suit here and pretend it's a fixed 1.8V
regulator. A proper fix can follow later. The BSP code seems to ignore
this regulator altogether.
Describe the AXP313A's voltage settings and switch registers, how the
voltages are encoded, and connect this to the MFD device via its
regulator ID.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Shengyu Qu <wiagn233@outlook.com>
Link: https://lore.kernel.org/r/20230524000012.15028-3-andre.przywara@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"AMD IOMMU fixes:
- Fix domain type and size checks
- IOTLB flush fix for invalidating ranges
- Guest IRQ handling fixes and GALOG overflow fix
Rockchip IOMMU:
- Error handling fix
Mediatek IOMMU:
- IOTLB flushing fix
Renesas IOMMU:
- Fix Kconfig dependencies to avoid build errors on RiscV"
* tag 'iommu-fixes-v6.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/mediatek: Flush IOTLB completely only if domain has been attached
iommu/amd/pgtbl_v2: Fix domain max address
iommu/amd: Fix domain flush size when syncing iotlb
iommu/amd: Add missing domain type checks
iommu/amd: Fix up merge conflict resolution
iommu/amd: Handle GALog overflows
iommu/amd: Don't block updates to GATag if guest mode is on
iommu/rockchip: Fix unwind goto issue
iommu: Make IPMMU_VMSA dependencies more strict
|
|
Pull drm fixes from Dave Airlie:
"Quiet enough week, though the misc fixes tree didn't get to me when I
was sending this, so maybe it'll be a bit bigger next week, just one
i915 fix and some scattered amdgpu fixes:
amdgpu:
- Fix mclk and fclk output ordering on some APUs
- Fix display regression with 5K VRR
- VCN, JPEG spurious interrupt warning fixes
- Fix SI DPM on some ARM64 platforms
- Fix missing TMZ enablement on GC 11.0.1
i915:
- Fix for OA reporting to allow detecting non-power-of-two reports"
* tag 'drm-fixes-2023-06-02' of git://anongit.freedesktop.org/drm/drm:
drm/i915/perf: Clear out entire reports after reading if not power of 2 size
drm/amdgpu: enable tmz by default for GC 11.0.1
drm/amd/pm: resolve reboot exception for si oland
drm/amdgpu: add RAS POISON interrupt funcs for jpeg_v4_0
drm/amdgpu: add RAS POISON interrupt funcs for jpeg_v2_6
drm/amdgpu: separate ras irq from jpeg instance irq for UVD_POISON
drm/amdgpu: add RAS POISON interrupt funcs for vcn_v4_0
drm/amdgpu: add RAS POISON interrupt funcs for vcn_v2_6
drm/amdgpu: separate ras irq from vcn instance irq for UVD_POISON
Revert "drm/amd/display: Do not set drr on pipe commit"
Revert "drm/amd/display: Block optimize on consecutive FAMS enables"
drm/amd/pm: reverse mclk and fclk clocks levels for renoir
drm/amd/pm: reverse mclk and fclk clocks levels for vangogh
drm/amd/pm: reverse mclk and fclk clocks levels for yellow carp
drm/amd/pm: reverse mclk clocks levels for SMU v13.0.5
drm/amd/pm: reverse mclk and fclk clocks levels for SMU v13.0.4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"A few minor fixes for EFI, one of which fixes the reported boot
regression when booting x86 kernels using the BIOS based loader built
into the hypervisor framework on macOS.
- fix harmless warning in zboot code on 'make clean'
- add some missing prototypes
- fix boot regressions triggered by PE/COFF header image minor
version bump"
* tag 'efi-fixes-for-v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: Bump stub image version for macOS HVF compatibility
efi: fix missing prototype warnings
efi/libstub: zboot: Avoid eager evaluation of objcopy flags
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix for OA reporting to allow detecting non-power-of-two reports
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZHimf55x/DyXYar1@jlahtine-mobl.ger.corp.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
"Most notable is a fix for a null-ptr-deref in fbcon's soft_cursor
function which was found by syzbot.
- Fix null-ptr-deref in soft_cursor
- various remove callback conversions
- error path fixes in imsttfb"
* tag 'fbdev-for-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: bw2: Convert to platform remove callback returning void
fbdev: broadsheetfb: Convert to platform remove callback returning void
fbdev: au1200fb: Convert to platform remove callback returning void
fbdev: au1100fb: Convert to platform remove callback returning void
fbdev: arcfb: Convert to platform remove callback returning void
fbdev: au1100fb: Drop if with an always false condition
fbcon: Fix null-ptr-deref in soft_cursor
fbdev: imsttfb: Fix error path of imsttfb_probe()
fbdev: imsttfb: Release framebuffer and dealloc cmap on error path
fbdev: matroxfb ssd1307fb: Switch i2c drivers back to use .probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
"MTD core:
- MAINTAINERS: Add Michal as reviewer instead of Naga
- mtdchar: Mark bits of ioctl handler noinline
NAND controller drivers:
- marvell:
- Don't set the NAND frequency select
- Ensure timing values are written
- ingenic: Fix empty stub helper definitions
SPI-NOR core:
- Fix divide by zero for spi-nor-generic flashes
SPI-NOR manufacturer driver:
- spansion: make sure local struct does not contain garbage"
* tag 'mtd/fixes-for-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: marvell: don't set the NAND frequency select
mtd: rawnand: marvell: ensure timing values are written
mtdchar: mark bits of ioctl handler noinline
MAINTAINERS: Add myself as reviewer instead of Naga
mtd: spi-nor: Fix divide by zero for spi-nor-generic flashes
mtd: rawnand: ingenic: fix empty stub helper definitions
mtd: spi-nor: spansion: make sure local struct does not contain garbage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Happy Wear a Dress Day.
Fairly standard-sized batch of fixes, accounting for the lack of
sub-tree submissions this week. The mlx5 IRQ fixes are notable, people
were complaining about that. No fires burning.
Current release - regressions:
- eth: mlx5e:
- multiple fixes for dynamic IRQ allocation
- prevent encap offload when neigh update is running
- eth: mana: fix perf regression: remove rx_cqes, tx_cqes counters
Current release - new code bugs:
- eth: mlx5e: DR, add missing mutex init/destroy in pattern manager
Previous releases - always broken:
- tcp: deny tcp_disconnect() when threads are waiting
- sched: prevent ingress Qdiscs from getting installed in random
locations in the hierarchy and moving around
- sched: flower: fix possible OOB write in fl_set_geneve_opt()
- netlink: fix NETLINK_LIST_MEMBERSHIPS length report
- udp6: fix race condition in udp6_sendmsg & connect
- tcp: fix mishandling when the sack compression is deferred
- rtnetlink: validate link attributes set at creation time
- mptcp: fix connect timeout handling
- eth: stmmac: fix call trace when stmmac_xdp_xmit() is invoked
- eth: amd-xgbe: fix the false linkup in xgbe_phy_status
- eth: mlx5e:
- fix corner cases in internal buffer configuration
- drain health before unregistering devlink
- usb: qmi_wwan: set DTR quirk for BroadMobi BM818
Misc:
- tcp: return user_mss for TCP_MAXSEG in CLOSE/LISTEN state if
user_mss set"
* tag 'net-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
mptcp: fix active subflow finalization
mptcp: add annotations around sk->sk_shutdown accesses
mptcp: fix data race around msk->first access
mptcp: consolidate passive msk socket initialization
mptcp: add annotations around msk->subflow accesses
mptcp: fix connect timeout handling
rtnetlink: add the missing IFLA_GRO_ tb check in validate_linkmsg
rtnetlink: move IFLA_GSO_ tb check to validate_linkmsg
rtnetlink: call validate_linkmsg in rtnl_create_link
ice: recycle/free all of the fragments from multi-buffer frame
net: phy: mxl-gpy: extend interrupt fix to all impacted variants
net: renesas: rswitch: Fix return value in error path of xmit
net: dsa: mv88e6xxx: Increase wait after reset deactivation
net: ipa: Use correct value for IPA_STATUS_SIZE
tcp: fix mishandling when the sack compression is deferred.
net/sched: flower: fix possible OOB write in fl_set_geneve_opt()
sfc: fix error unwinds in TC offload
net/mlx5: Read embedded cpu after init bit cleared
net/mlx5e: Fix error handling in mlx5e_refresh_tirs
net/mlx5: Ensure af_desc.mask is properly initialized
...
|
|
When switching from kthreads to vhost_tasks two bugs were added:
1. The vhost worker tasks's now show up as processes so scripts doing
ps or ps a would not incorrectly detect the vhost task as another
process. 2. kthreads disabled freeze by setting PF_NOFREEZE, but
vhost tasks's didn't disable or add support for them.
To fix both bugs, this switches the vhost task to be thread in the
process that does the VHOST_SET_OWNER ioctl, and has vhost_worker call
get_signal to support SIGKILL/SIGSTOP and freeze signals. Note that
SIGKILL/STOP support is required because CLONE_THREAD requires
CLONE_SIGHAND which requires those 2 signals to be supported.
This is a modified version of the patch written by Mike Christie
<michael.christie@oracle.com> which was a modified version of patch
originally written by Linus.
Much of what depended upon PF_IO_WORKER now depends on PF_USER_WORKER.
Including ignoring signals, setting up the register state, and having
get_signal return instead of calling do_group_exit.
Tidied up the vhost_task abstraction so that the definition of
vhost_task only needs to be visible inside of vhost_task.c. Making
it easier to review the code and tell what needs to be done where.
As part of this the main loop has been moved from vhost_worker into
vhost_task_fn. vhost_worker now returns true if work was done.
The main loop has been updated to call get_signal which handles
SIGSTOP, freezing, and collects the message that tells the thread to
exit as part of process exit. This collection clears
__fatal_signal_pending. This collection is not guaranteed to
clear signal_pending() so clear that explicitly so the schedule()
sleeps.
For now the vhost thread continues to exist and run work until the
last file descriptor is closed and the release function is called as
part of freeing struct file. To avoid hangs in the coredump
rendezvous and when killing threads in a multi-threaded exec. The
coredump code and de_thread have been modified to ignore vhost threads.
Remvoing the special case for exec appears to require teaching
vhost_dev_flush how to directly complete transactions in case
the vhost thread is no longer running.
Removing the special case for coredump rendezvous requires either the
above fix needed for exec or moving the coredump rendezvous into
get_signal.
Fixes: 6e890c5d5021 ("vhost: use vhost_tasks for worker threads")
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Co-developed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-05-31
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Read embedded cpu after init bit cleared
net/mlx5e: Fix error handling in mlx5e_refresh_tirs
net/mlx5: Ensure af_desc.mask is properly initialized
net/mlx5: Fix setting of irq->map.index for static IRQ case
net/mlx5: Remove rmap also in case dynamic MSIX not supported
====================
Link: https://lore.kernel.org/r/20230601031051.131529-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.4
- Fixes for spurious Keep Alive timeouts (Uday)
- Fix for command type check on passthrough actions (Min)
- Fix for nvme command name for error logging (Christoph)"
* tag 'nvme-6.4-2023-06-01' of git://git.infradead.org/nvme:
nvme: fix the name of Zone Append for verbose logging
nvme: improve handling of long keep alives
nvme: check IO start time when deciding to defer KA
nvme: double KA polling frequency to avoid KATO with TBKAS on
nvme: fix miss command type check
|
|
The ice driver caches next_to_clean value at the beginning of
ice_clean_rx_irq() in order to remember the first buffer that has to be
freed/recycled after main Rx processing loop. The end boundary is
indicated by first descriptor of frame that Rx processing loop has ended
its duties. Note that if mentioned loop ended in the middle of gathering
multi-buffer frame, next_to_clean would be pointing to the descriptor in
the middle of the frame BUT freeing/recycling stage will stop at the
first descriptor. This means that next iteration of ice_clean_rx_irq()
will miss the (first_desc, next_to_clean - 1) entries.
When running various 9K MTU workloads, such splats were observed:
[ 540.780716] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 540.787787] #PF: supervisor read access in kernel mode
[ 540.793002] #PF: error_code(0x0000) - not-present page
[ 540.798218] PGD 0 P4D 0
[ 540.800801] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 540.805231] CPU: 18 PID: 3984 Comm: xskxceiver Tainted: G W 6.3.0-rc7+ #96
[ 540.813619] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 540.824209] RIP: 0010:ice_clean_rx_irq+0x2b6/0xf00 [ice]
[ 540.829678] Code: 74 24 10 e9 aa 00 00 00 8b 55 78 41 31 57 10 41 09 c4 4d 85 ff 0f 84 83 00 00 00 49 8b 57 08 41 8b 4f 1c 65 8b 35 1a fa 4b 3f <48> 8b 02 48 c1 e8 3a 39 c6 0f 85 a2 00 00 00 f6 42 08 02 0f 85 98
[ 540.848717] RSP: 0018:ffffc9000f42fc50 EFLAGS: 00010282
[ 540.854029] RAX: 0000000000000004 RBX: 0000000000000002 RCX: 000000000000fffe
[ 540.861272] RDX: 0000000000000000 RSI: 0000000000000001 RDI: 00000000ffffffff
[ 540.868519] RBP: ffff88984a05ac00 R08: 0000000000000000 R09: dead000000000100
[ 540.875760] R10: ffff88983fffcd00 R11: 000000000010f2b8 R12: 0000000000000004
[ 540.883008] R13: 0000000000000003 R14: 0000000000000800 R15: ffff889847a10040
[ 540.890253] FS: 00007f6ddf7fe640(0000) GS:ffff88afdf800000(0000) knlGS:0000000000000000
[ 540.898465] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 540.904299] CR2: 0000000000000000 CR3: 000000010d3da001 CR4: 00000000007706e0
[ 540.911542] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 540.918789] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 540.926032] PKRU: 55555554
[ 540.928790] Call Trace:
[ 540.931276] <TASK>
[ 540.933418] ice_napi_poll+0x4ca/0x6d0 [ice]
[ 540.937804] ? __pfx_ice_napi_poll+0x10/0x10 [ice]
[ 540.942716] napi_busy_loop+0xd7/0x320
[ 540.946537] xsk_recvmsg+0x143/0x170
[ 540.950178] sock_recvmsg+0x99/0xa0
[ 540.953729] __sys_recvfrom+0xa8/0x120
[ 540.957543] ? do_futex+0xbd/0x1d0
[ 540.961008] ? __x64_sys_futex+0x73/0x1d0
[ 540.965083] __x64_sys_recvfrom+0x20/0x30
[ 540.969155] do_syscall_64+0x38/0x90
[ 540.972796] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 540.977934] RIP: 0033:0x7f6de5f27934
To fix this, set cached_ntc to first_desc so that at the end, when
freeing/recycling buffers, descriptors from first to ntc are not missed.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230531154457.3216621-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The interrupt fix in commit 97a89ed101bb should be applied on all variants
of GPY2xx PHY and GPY115C.
Fixes: 97a89ed101bb ("net: phy: mxl-gpy: disable interrupts on GPY215 by default")
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230531074822.39136-1-lxu@maxlinear.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix return value in the error path of rswitch_start_xmit(). If TX
queues are full, this function should return NETDEV_TX_BUSY.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230529073817.1145208-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-2-chris.packham@alliedtelesis.co.nz
|
|
When new timing values are calculated in marvell_nfc_setup_interface()
ensure that they will be applied in marvell_nfc_select_target() by
clearing the selected_chip pointer.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-1-chris.packham@alliedtelesis.co.nz
|
|
The addition of the mtdchar_read_ioctl() function caused the stack usage
of mtdchar_ioctl() to grow beyond the warning limit on 32-bit architectures
with gcc-13:
drivers/mtd/mtdchar.c: In function 'mtdchar_ioctl':
drivers/mtd/mtdchar.c:1229:1: error: the frame size of 1488 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Mark both the read and write portions as noinline_for_stack to ensure
they don't get inlined and use separate stack slots to reduce the
maximum usage, both in the mtdchar_ioctl() and combined with any
of its callees.
Fixes: 095bb6e44eb1 ("mtdchar: add MEMREAD ioctl")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230417205654.1982368-1-arnd@kernel.org
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox fix from Jassi Brar:
"Fix missing mutex unlock in mailbox-test"
* tag 'mailbox-fixes-6.4-rc5' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: mailbox-test: fix a locking issue in mbox_test_message_write()
|
|
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- Regression fix for overlong long timeouts during initialization on
some Logitech Unifying devices (Bastien Nocera)
- error handling and overflow fixes for Wacom driver (Denis Arefev,
Jason Gerecke, Nikita Zhandarovich)
* tag 'for-linus-2023060101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-hidpp: Handle timeout differently from busy
HID: wacom: Add error check to wacom_parse_and_register()
HID: google: add jewel USB id
HID: wacom: avoid integer overflow in wacom_intuos_inout()
HID: wacom: Check for string overflow from strscpy calls
|
