| Age | Commit message (Collapse) | Author |
|---|
|
- Wait up to 1 second for DOE Busy bit to clear before writing a request to
the mailbox to avoid failures if the mailbox is still busy from a
previous transfer (Gregory Price)
* pci/doe:
PCI/DOE: Poll DOE Busy bit for up to 1 second in pci_doe_send_req()
|
|
- Add read/modify/write locking for Link Control 2, which is used to manage
Link speed (Ilpo Järvinen)
- Cache all supported Link speeds for use by the PCIe bandwidth controller
(Ilpo Järvinen)
- Extract the Link Bandwidth Management Status check into pcie_lbms_seen(),
where it can be shared between the bandwidth controller and quirks that
use it to help retrain failed links (Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address the
reasons it was previously reverted (Alexandru Gagniuc, Ilpo Järvinen)
- Add pcie_set_target_speed() and related functionality to manage PCIe Link
speed based on thermal constraints (Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the existing
thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
- Drop duplicate pcie_get_speed_cap(), pcie_get_width_cap() declarations
(Bjorn Helgaas)
* pci/bwctrl:
PCI: Drop duplicate pcie_get_speed_cap(), pcie_get_width_cap() declarations
selftests/pcie_bwctrl: Create selftests
thermal: Add PCIe cooling driver
PCI/bwctrl: Add pcie_set_target_speed() to set PCIe Link Speed
PCI/bwctrl: Re-add BW notification portdrv as PCIe BW controller
PCI: Abstract LBMS seen check into pcie_lbms_seen()
PCI: Refactor pcie_update_link_speed()
PCI: Store all PCIe Supported Link Speeds
PCI: Protect Link Control 2 Register with RMW locking
Documentation PCI: Reformat RMW ops documentation
|
|
Currently, the Rockchip PCIe endpoint controller driver does not handle
the PERST# signal, which prevents detecting when link training should
actually be started or if the host resets the device. This however can
be supported using the controller reset_gpios property set as an input
GPIO for endpoint mode.
Modify the Rockchip PCI endpoint controller driver to get the reset_gpio
and its associated interrupt which is serviced using a threaded IRQ with
the function rockchip_pcie_ep_perst_irq_thread() as handler.
This handler function notifies a link down event corresponding to the RC
side asserting the PERST# signal using pci_epc_linkdown() when the gpio
is high. Once the gpio value goes down, corresponding to the RC
de-asserting the PERST# signal, link training is started. The polarity
of the gpio interrupt trigger is changed from high to low after the RC
asserted PERST#, and conversely changed from low to high after the RC
de-asserts PERST#.
Also, given that the host mode controller and the endpoint mode
controller use two different property names for the same PERST# signal
(ep_gpios property and reset_gpios property respectively), for clarity,
rename the ep_gpio field of struct rockchip_pcie to perst_gpio.
Link: https://lore.kernel.org/r/20241017015849.190271-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: make log messages consistent, add missing include]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Rockchip RK3399 TRM V1.3 Part2, Section 17.5.8.1.2, step 7,
describes the endpoint mode link training process clearly and states
that:
Insure link training completion and success by observing link_st field
in PCIe Client BASIC_STATUS1 register change to 2'b11. If both side
support PCIe Gen2 speed, re-train can be Initiated by asserting the
Retrain Link field in Link Control and Status Register. The software
should insure the BASIC_STATUS0[negotiated_speed] changes to "1", that
indicates re-train to Gen2 successfully.
This procedure is very similar to what is done for the root-port mode
in rockchip_pcie_host_init_port().
Implement this link training procedure for the endpoint mode as well.
Given that the RK3399 SoC does not have an interrupt signaling link
status changes, training is implemented as a delayed work which is
rescheduled until the link training completes or the endpoint controller
is stopped. The link training work is first scheduled in
rockchip_pcie_ep_start() when the endpoint function is started. Link
training completion is signaled to the function using pci_epc_linkup().
Accordingly, the linkup_notifier field of the Rockchip pci_epc_features
structure is changed to true.
Link: https://lore.kernel.org/r/20241017015849.190271-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: update log messages to make them consistent]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Define the EPC operation ->stop() for the Rockchip endpoint driver with
the function rockchip_pcie_ep_stop(). This function disables link
training and the controller configuration, as the reverse to what
the start operation defined with rockchip_pcie_ep_start() does.
Link: https://lore.kernel.org/r/20241017015849.190271-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The function rockchip_pcie_init_port() enables link training for a
controller configured in EP mode. Enabling link training is again done
in rockchip_pcie_ep_probe() after that function executed
rockchip_pcie_init_port(). Enabling link training only needs to be done
once, and doing so at the probe stage before the controller is actually
started by the user serves no purpose.
Refactor this by removing the link training enablement from both
rockchip_pcie_init_port() and rockchip_pcie_ep_probe() and moving it to
the endpoint start operation defined with rockchip_pcie_ep_start().
Enabling the controller configuration using the PCIE_CLIENT_CONF_ENABLE
bit in the same PCIE_CLIENT_CONFIG register is also moved to
rockchip_pcie_ep_start() and both the controller configuration and link
training enable bits are set with a single call to
rockchip_pcie_write().
Link: https://lore.kernel.org/r/20241017015849.190271-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the code in rockchip_pcie_ep_probe() to hide the MSI-X capability
to its own function, rockchip_pcie_ep_hide_broken_msix_cap().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Introduce the function rockchip_pcie_ep_init_ob_mem() allocate the
outbound memory regions and memory needed for IRQ handling.
These changes tidy up rockchip_pcie_ep_probe().
No functional change.
Link: https://lore.kernel.org/r/20241017015849.190271-9-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
To be consistent with the usual "get_resources" naming of driver
functions that acquire controller resources like clocks, PHY etc,
rename the function rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The call to rockchip_pcie_prog_ep_ob_atu() used to map the PCI address
of MSI data to the memory window allocated on probe for IRQs is done
in rockchip_pcie_ep_send_msi_irq() assuming a fixed alignment to a
256B boundary of the PCI address. This is not correct as the alignment
constraint for the RK3399 PCI mapping depends on the number of bits of
address changing in the mapped region. This leads to an unstable system
which sometimes work and sometimes does not (crashing on paging faults
when memcpy_toio() or memcpy_fromio() are used).
Similar to regular data mapping, the MSI data mapping must thus be
handled according to the information provided by
rockchip_pcie_ep_align_addr(). Modify rockchip_pcie_ep_send_msi_irq()
to use rockchip_pcie_ep_align_addr() to correctly program entry 0 of
the ATU for sending MSI IRQs.
Link: https://lore.kernel.org/r/20241017015849.190271-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits from the CPU address space used for the
mapping. For a PCI mapping of size bytes starting from pci_addr, the
number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1], up to 20 bits, that is,
up to 1MB mappings.
This means that when preparing a PCI address mapping, an endpoint
function driver must use an offset into the allocated controller
memory region that is equal to the mask of the starting PCI address
over rockchip_pcie_ep_ob_atu_num_bits() bits. This offset also
determines the maximum size of the mapping given the starting PCI
address and the fixed 1MB controller memory window size.
Implement the ->align_addr() endpoint controller operation to allow the
mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/r/20241017015849.190271-6-dlemoal@kernel.org
Co-developed-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: change local variable name for address offset]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a check to verify that the outbound region to be used for mapping an
address is not already in use.
Link: https://lore.kernel.org/r/20241017015849.190271-5-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
There is no need to loop over all regions to find the memory window used
to map an address. We can use rockchip_ob_region() to determine the
region index, together with a check that the address passed as argument
is the address used to create the mapping. Furthermore, the
ob_region_map bitmap should also be checked to ensure that we are not
attempting to unmap an address that is not mapped.
Link: https://lore.kernel.org/r/20241017015849.190271-4-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Introduce the macro ROCKCHIP_PCIE_AT_SIZE_ALIGN to initialize the .align
field of the controller epc_features structure to 256. This is defined
as a shift using the macro ROCKCHIP_PCIE_AT_MIN_NUM_BITS (to avoid
using the "magic" value 8 directly).
Link: https://lore.kernel.org/r/20241017015849.190271-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
The function silently assumed that signaling was already enabled for the
dma_fence_array. This meant that without enabling signaling first we would
never see forward progress.
Fix that by falling back to testing each individual fence when signaling
isn't enabled yet.
v2: add the comment suggested by Boris why this is done this way
v3: fix the underflow pointed out by Tvrtko
v4: atomic_read_acquire() as suggested by Tvrtko
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Chia-I Wu <olvaffe@gmail.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Closes: https://gitlab.freedesktop.org/mesa/mesa/-/issues/12094
Cc: <stable@vger.kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241112121925.18464-1-christian.koenig@amd.com
|
|
The portid_bits and deviceid_bits were set only for XP type nodes in
the arm_cmn_discover() and it confused other nodes to find XP nodes.
Copy the both bits from the XP nodes directly when it sets up a new
node.
Fixes: e79634b53e39 ("perf/arm-cmn: Refactor node ID handling. Again.")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20241121001334.331334-1-namhyung@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Same as
https://lore.kernel.org/all/20240514180050.182454-1-namhyung@kernel.org/,
we should skip `for_each_sibling_event()` for group leader since it
doesn't have the ctx yet.
Fixes: f3c0eba28704 ("perf: Add a few assertions")
Reported-by: Greg Thelen <gthelen@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tuan Phan <tuanphan@os.amperecomputing.com>
Signed-off-by: Chun-Tse Shao <ctshao@google.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241108050806.3730811-1-ctshao@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- support for NT36672A touchscreen added to novatek-nvt-ts driver
- a change to ads7846 driver to prevent XPT2046 from locking up
- a change switching platform input dirves back to using remove()
method (from remove_new())
- updates to a number of input drivers to use the new cleanup
facilities (__free(...), guard(), and scoped-guard()) which ensure
that the resources and locks are released properly and automatically
- other assorted driver cleanups and fixes.
* tag 'input-for-v6.13-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (109 commits)
Input: mpr121 - use devm_regulator_get_enable_read_voltage()
Input: sun4i-lradc-keys - don't include 'pm_wakeup.h' directly
Input: spear-keyboard - don't include 'pm_wakeup.h' directly
Input: cypress-sf - constify struct i2c_device_id
Input: ads7846 - increase xfer array size in 'struct ser_req'
Input: fix the input_event struct documentation
Input: i8042 - fix typo dublicate to duplicate
Input: ads7846 - add dummy command register clearing cycle
Input: cs40l50 - fix wrong usage of INIT_WORK()
Input: introduce notion of passive observers for input handlers
Input: maple_keyb - use guard notation when acquiring mutex
Input: locomokbd - use guard notation when acquiring spinlock
Input: hilkbd - use guard notation when acquiring spinlock
Input: synaptics-rmi4 - switch to using cleanup functions in F34
Input: synaptics - fix a typo
dt-bindings: input: rotary-encoder: Fix "rotary-encoder,rollover" type
Input: omap-keypad - use guard notation when acquiring mutex
Input: imagis - fix warning regarding 'imagis_3038_data' being unused
Input: userio - remove unneeded semicolon
Input: sparcspkr - use cleanup facility for device_node
...
|
|
This reverts commit 6fd47effe92b, and the related self-test update
commit e14e0eaeb040 ("selftests/hid: add test for assigning a given
device to hid-generic").
It results in things like the scroll wheel on Logitech mice not working
after a reboot due to the kernel being confused about the state of the
high-resolution mode.
Quoting Benjamin Tissoires:
"The idea of 6fd47effe92b was to be able to call hid_bpf_rdesc_fixup()
once per reprobe of the device.
However, because the bpf filter can now change the quirk value, the
call had to be moved before the driver gets bound (which was
previously ensuring the unicity of the call).
The net effect is that now, in the case hid-generic gets loaded first
and then the specific driver gets loaded once the disk is available,
the value of ->quirks is not reset, but kept to the value that was set
by hid-generic (HID_QUIRK_INPUT_PER_APP).
Once hid-logitech-hidpp kicks in, that quirk is now set, which creates
two inputs for the single mouse: one keyboard for fancy shortcuts, and
one mouse node.
However, hid-logitech-hidpp expects only one input node to be attached
(it stores it into hidpp->input), and when a wheel event is received,
because there is some processing with high-resolution wheel events,
the wheel event is injected into hidpp->input.
And of course, when HID_QUIRK_INPUT_PER_APP is set, hidpp->input gets
the keyboard node, which doesn't have wheel event type, and the events
are ignored"
Reported-and-bisected-by: Mike Galbraith <efault@gmx.de>
Link: https://lore.kernel.org/all/CAHk-=wiUkQM3uheit2cNM0Y0OOY5qqspJgC8LkmOkJ2p2LDxcw@mail.gmail.com/
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are cases where a PCIe extended capability should be hidden from
the user. For example, an unknown capability (i.e., capability with ID
greater than PCI_EXT_CAP_ID_MAX) or a capability that is intentionally
chosen to be hidden from the user.
Hiding a capability is done by virtualizing and modifying the 'Next
Capability Offset' field of the previous capability so it points to the
capability after the one that should be hidden.
The special case where the first capability in the list should be hidden
is handled differently because there is no previous capability that can
be modified. In this case, the capability ID and version are zeroed
while leaving the next pointer intact. This hides the capability and
leaves an anchor for the rest of the capability list.
However, today, hiding the first capability in the list is not done
properly if the capability is unknown, as struct
vfio_pci_core_device->pci_config_map is set to the capability ID during
initialization but the capability ID is not properly checked later when
used in vfio_config_do_rw(). This leads to the following warning [1] and
to an out-of-bounds access to ecap_perms array.
Fix it by checking cap_id in vfio_config_do_rw(), and if it is greater
than PCI_EXT_CAP_ID_MAX, use an alternative struct perm_bits for direct
read only access instead of the ecap_perms array.
Note that this is safe since the above is the only case where cap_id can
exceed PCI_EXT_CAP_ID_MAX (except for the special capabilities, which
are already checked before).
[1]
WARNING: CPU: 118 PID: 5329 at drivers/vfio/pci/vfio_pci_config.c:1900 vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
CPU: 118 UID: 0 PID: 5329 Comm: simx-qemu-syste Not tainted 6.12.0+ #1
(snip)
Call Trace:
<TASK>
? show_regs+0x69/0x80
? __warn+0x8d/0x140
? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
? report_bug+0x18f/0x1a0
? handle_bug+0x63/0xa0
? exc_invalid_op+0x19/0x70
? asm_exc_invalid_op+0x1b/0x20
? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
? vfio_pci_config_rw+0x244/0x430 [vfio_pci_core]
vfio_pci_rw+0x101/0x1b0 [vfio_pci_core]
vfio_pci_core_read+0x1d/0x30 [vfio_pci_core]
vfio_device_fops_read+0x27/0x40 [vfio]
vfs_read+0xbd/0x340
? vfio_device_fops_unl_ioctl+0xbb/0x740 [vfio]
? __rseq_handle_notify_resume+0xa4/0x4b0
__x64_sys_pread64+0x96/0xc0
x64_sys_call+0x1c3d/0x20d0
do_syscall_64+0x4d/0x120
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fixes: 89e1f7d4c66d ("vfio: Add PCI device driver")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Tested-by: Yi Liu <yi.l.liu@intel.com>
Link: https://lore.kernel.org/r/20241124142739.21698-1-avihaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The group only contains a single entry and the conditionals around its
lifecycle make clear that this won't change.
Remove the unnecessary group.
This saves some memory and it's easier to read.
The removal of a non-const bin_attribute[] instance is also a
preparation for the constification of struct bin_attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20241121-sysfs-const-bin_attr-int340x_thermal-v1-1-2436facf9dae@weissschuh.net
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the current_uuid attribute is set to the active policy UUID,
reading back the same attribute is returning "INVALID" instead of
the active policy UUID on some platforms before Ice Lake.
In platforms before Ice Lake, firmware provides a list of supported
thermal policies. In this case, user space can select any of the
supported thermal policies via a write to attribute "current_uuid".
In commit c7ff29763989 ("thermal: int340x: Update OS policy capability
handshake")', the OS policy handshake was updated to support Ice Lake
and later platforms and it treated priv->current_uuid_index=0 as
invalid. However, priv->current_uuid_index=0 is for the active policy,
only priv->current_uuid_index=-1 is invalid.
Fix this issue by updating the priv->current_uuid_index check.
Fixes: c7ff29763989 ("thermal: int340x: Update OS policy capability handshake")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.18+ <stable@vger.kernel.org> # 5.18+
Link: https://patch.msgid.link/20241114200213.422303-1-srinivas.pandruvada@linux.intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Prepare input updates for 6.13 merge window.
|
|
VCAP API unit tests fail randomly with errors such as
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:387
Expected 134 + 7 == iter.offset, but
134 + 7 == 141 (0x8d)
iter.offset == 17214 (0x433e)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:388
Expected 5 == iter.reg_idx, but
iter.reg_idx == 702 (0x2be)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:389
Expected 11 == iter.reg_bitpos, but
iter.reg_bitpos == 15 (0xf)
# vcap_api_iterator_init_test: pass:0 fail:1 skip:0 total:1
Comments in the code state that "A typegroup table ends with an all-zero
terminator". Add the missing terminators.
Some of the typegroups did have a terminator of ".offset = 0, .width = 0,
.value = 0,". Replace those terminators with "{ }" (no trailing ',') for
consistency and to excplicitly state "this is a terminator".
Fixes: 67d637516fa9 ("net: microchip: sparx5: Adding KUNIT test for the VCAP API")
Cc: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119213202.2884639-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate Wake-on-LAN (WoL) options in `lan78xx_set_wol` before calling
`usb_autopm_get_interface`. This prevents USB autopm refcounting issues
and ensures the adapter can properly enter autosuspend when invalid WoL
options are provided.
Fixes: eb9ad088f966 ("lan78xx: Check for supported Wake-on-LAN modes")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://patch.msgid.link/20241118140351.2398166-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hardware on Broadcom 1G chipsets have a known limitation
where they cannot handle DMA addresses that cross over 4GB.
When such an address is encountered, the hardware sets the
address overflow error bit in the DMA status register and
triggers a reset.
However, BCM57766 hardware is setting the overflow bit and
triggering a reset in some cases when there is no actual
underlying address overflow. The hardware team analyzed the
issue and concluded that it is happening when the status
block update has an address with higher (b16 to b31) bits
as 0xffff following a previous update that had lowest bits
as 0xffff.
To work around this bug in the BCM57766 hardware, set the
coherent dma mask from the current 64b to 31b. This will
ensure that upper bits of the status block DMA address are
always at most 0x7fff, thus avoiding the improper overflow
check described above. This work around is intended for only
status block and ring memories and has no effect on TX and
RX buffers as they do not require coherent memory.
Fixes: 72f2afb8a685 ("[TG3]: Add DMA address workaround")
Reported-by: Salam Noureddine <noureddine@arista.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20241119055741.147144-1-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add calls to `phy_device_free` after `fixed_phy_unregister` to fix a
memory leak that occurs when the device is unplugged. This ensures
proper cleanup of pseudo fixed-link PHYs.
Fixes: 89b36fb5e532 ("lan78xx: Lan7801 Support for Fixed PHY")
Cc: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In lan78xx_probe(), the buffer `buf` was being freed twice: once
implicitly through `usb_free_urb(dev->urb_intr)` with the
`URB_FREE_BUFFER` flag and again explicitly by `kfree(buf)`. This caused
a double free issue.
To resolve this, reordered `kmalloc()` and `usb_alloc_urb()` calls to
simplify the initialization sequence and removed the redundant
`kfree(buf)`. Now, `buf` is allocated after `usb_alloc_urb()`, ensuring
it is correctly managed by `usb_fill_int_urb()` and freed by
`usb_free_urb()` as intended.
Fixes: a6df95cae40b ("lan78xx: Fix memory allocation bug")
Cc: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Type 4 PCC channels have an option to send back a response
to the platform when they are done processing the request.
The flag to indicate whether or not to respond is inside
the message body, and thus is not available to the pcc
mailbox.
If the flag is not set, still set command completion
bit after processing message.
In order to read the flag, this patch maps the shared
buffer to virtual memory. To avoid duplication of mapping
the shared buffer is then made available to be used by
the driver that uses the mailbox.
Signed-off-by: Adam Young <admiyo@os.amperecomputing.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mailbox to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Make a few indentions consistent while touching these struct
initializers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Replace %i with %u in snprintf() because it is "unsigned int".
Signed-off-by: zhang jiao <zhangjiao2@cmss.chinamobile.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Both the inner and outer loops in this code use the "i" iterator.
The inner loop should really use a different iterator.
It doesn't affect things in practice because the data comes from the
device tree. The "protocol" and "windows" variables are going to be
zero. That means we're always going to hit the "return &chans[channel];"
statement and we're not going to want to iterate through the outer
loop again.
Still it's worth fixing this for future use cases.
Fixes: 5a6338cce9f4 ("mailbox: arm_mhuv2: Add driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
As per zynqmp-ipi bindings, zynqmp IPI node can have multiple child nodes.
Current IPI setup function is set only for first child node. If IPI node
has multiple child nodes in the device-tree, then IPI setup fails for
child nodes other than first child node. In such case kernel will crash.
Fix this crash by registering IPI setup function for each available child
node.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
This driver was tested using the drm/imagination GPU driver. It was able
to successfully power on the GPU, by passing a command through mailbox
from E910 core to E902 that's responsible for powering up the GPU. The
GPU driver was able to read the BVNC version from control registers,
which confirms it was successfully powered on.
[ 33.957467] powervr ffef400000.gpu: [drm] loaded firmware
powervr/rogue_36.52.104.182_v1.fw
[ 33.966008] powervr ffef400000.gpu: [drm] FW version v1.0 (build
6621747 OS)
[ 38.978542] powervr ffef400000.gpu: [drm] *ERROR* Firmware failed to
boot
Though the driver still fails to boot the firmware, the mailbox driver
works when used with the not-yet-upstreamed firmware AON driver. There
is ongoing work to get the BXM-4-64 supported with the drm/imagination
driver [1], though it's not completed yet.
This work is based on the driver from the vendor kernel [2].
Link: https://gitlab.freedesktop.org/imagination/linux-firmware/-/issues/2 [1]
Link: https://github.com/revyos/thead-kernel.git [2]
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
It should be size of the struct clk_bulk_data, not data pointer pass to
devm_kcalloc().
Fixes: aa1609f571ca ("mailbox: mtk-cmdq: Dynamically allocate clk_bulk_data structure")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The TI message manager driver can be compiled without ARCH_KEYSTONE
nor ARCH_K3 enabled. Allow it to be built under COMPILE_TEST.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
When OF support is disabled the of_device_id struct match table can be
conditionally compiled out, this helper allows the assignment to also be
turned into a NULL conditionally. When the of_device_id struct is not
conditionally defined based on OF then the table will be unused causing a
warning. The two options are to either set the table as _maybe_unused, or
to just remove this helper since the table will always be defined.
Do the latter here.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The qcom-cpucp mailbox irq is expected to function during suspend-resume
cycle particularly when the scmi cpufreq driver can query the current
frequency using the get_level message after the cpus are brought up during
resume. Hence mark the irq with IRQF_NO_SUSPEND flag to fix the do_xfer
failures we see during resume.
Err Logs:
arm-scmi firmware:scmi: timed out in resp(caller:do_xfer+0x164/0x568)
cpufreq: cpufreq_online: ->get() failed
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Closes: https://lore.kernel.org/lkml/ZtgFj1y5ggipgEOS@hovoldconsulting.com/
Fixes: 0e2a9a03106c ("mailbox: Add support for QTI CPUCP mailbox controller")
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
pm_runtime_put_autosuspend() will soon be changed to include a call to
pm_runtime_mark_last_busy(). This patch switches the current users to
__pm_runtime_put_autosuspend() which will continue to have the
functionality of old pm_runtime_put_autosuspend().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The two previous bindings for this hardware were incorrect, as the
control/status and interrupt register regions should have been described
as syscons and dealt with via regmap in the driver. Add support for
accessing these registers using that method now, so that the hwmon
driver can be supported without using auxdev or hacks with io_remap().
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Commit 120584c728a6 ("hwmon: (aquacomputer_d5next) Add support for Octo
flow sensor") added support for reading Octo flow sensor, but didn't
update the priv->speed_input array length. Since Octo has 8 fans, with
the addition of the flow sensor the proper length for speed_input is 9.
Reported by Arne Schwabe on Github [1], who received a UBSAN warning.
Fixes: 120584c728a6 ("hwmon: (aquacomputer_d5next) Add support for Octo flow sensor")
Closes: https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/100 [1]
Reported-by: Arne Schwabe <arne@rfc2549.org>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Message-ID: <20241124152725.7205-1-savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In commit 35eba185fd1a ("i2c: designware: Calculate SCL timing parameter
for High Speed Mode") the SCL high period count and low period count for
high speed mode are calculated based on fixed tHIGH = 160 and tLOW = 120.
However, the set of two fixed values is only applicable to the combination
of hardware parameters IC_CAP_LOADING is 400 and IC_CLK_FREQ_OPTIMIZATION
is true. Outside of this combination, the SCL frequency may not reach
3.4 MHz because the fixed tHIGH and tLOW are not small enough.
If IC_CAP_LOADING is 400, it means the bus capacitance is 400pF;
Otherwise, 100 pF. If IC_CLK_FREQ_OPTIMIZATION is true, it means that the
hardware reduces its internal clock frequency by reducing the internal
latency required to generate the high period and low period of the SCL line.
Section 3.15.4.5 in DesignWare DW_apb_i2b Databook v2.03 says that when
IC_CLK_FREQ_OPTIMIZATION = 0,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 120 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 160 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
and section 3.15.4.6 says that when IC_CLK_FREQ_OPTIMIZATION = 1,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 160 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 120 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
In order to calculate more accurate SCL high period count and low period
count for high speed mode, two hardware parameters IC_CAP_LOADING and
IC_CLK_FREQ_OPTIMIZATION must be considered together. Since there're no
registers controlliing these these two hardware parameters, users can
declare them in the device tree so that the driver can obtain them.
Signed-off-by: Michael Wu <michael.wu@kneron.us>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
- BRCR value must go into the BRCR1 field when in high-speed mode.
It goes into BRCR2 otherwise.
- Remove fallback to standard mode if priv->sm > I2C_FREQ_MODE_FAST.
- Set SM properly in probe; previously it only checked STANDARD versus
FAST. Now we set STANDARD, FAST, FAST_PLUS or HIGH_SPEED.
- Remove all comment sections saying we only support low-speeds.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Current BRCR computation is:
brcr = floor(i2cclk / (clkfreq * div))
With brcr: "baud rate counter", an internal clock divider,
and i2cclk: input clock rate (24MHz, 38.4MHz or 48MHz),
and clkfreq: desired bus rate,
and div: speed-mode dependent divider (2 for standard, 3 otherwise).
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) = 4
and resulting bus rate = 48MHz / (4 * 3) = 4MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) = 12
and resulting bus rate = 38.4MHz / (12 * 3) = 1066kHz
The current computation means we always pick the smallest divider that
gives a bus rate above target. We should instead pick the largest
divider that gives a bus rate below target, using:
brcr = floor(i2cclk / (clkfreq * div)) + 1
If we redo the above examples:
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) + 1 = 5
and resulting bus rate = 48MHz / (5 * 3) = 3.2MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) + 1 = 13
and resulting bus rate = 38.4MHz / (13 * 3) = 985kHz
In kernel C code, floor(x) is DIV_ROUND_DOWN() and,
floor(x)+1 is DIV_ROUND_UP().
This is much less of an issue with slower bus rates (ie those currently
supported), because the gap from one divider to the next is much
smaller. It however keeps us from always using bus rates superior to
the target.
This fix is required for later on supporting faster bus rates:
I2C_FREQ_MODE_FAST_PLUS (1MHz) and I2C_FREQ_MODE_HIGH_SPEED (3.4MHz).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add EyeQ6H support to the nmk-i2c AMBA driver. It shares the same quirk
as EyeQ5: the memory bus only supports 32-bit accesses. Avoid writeb()
and readb() by reusing the same `priv->has_32b_bus` flag.
It does NOT need to write speed-mode specific value into a register;
therefore it does not depend on the mobileye,olb DT property.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Compatible-specific behavior is implemented using a if-condition on the
return value from of_device_is_compatible(), from probe. It does not
scale well when compatible number increases. Switch to using a match
table and a call to of_match_device().
We DO NOT attach a .of_match_table field to our amba driver, as we do
not use the table to match our driver to devices.
Sort probe variable declarations in reverse christmas tree to try and
introduce some logic into the ordering.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Enable DWAPB I2C controller support on FUJITSU-MONAKA.
This will be used in the FUJITSU-MONAKA server scheduled
for shipment in 2027.
The DSDT information obtained when verified using an
in-house simulator is presented below.
Device (SMB0)
{
Name (_HID, "FUJI200B") // _HID: Hardware ID
Name (_UID, Zero) // _UID: Unique ID
...
Name (_CRS, ResourceTemplate ()
{
Memory32Fixed (ReadWrite,
0x2A4B0000, // Address Base
0x00010000, // Address Length
)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive, ,, )
{
0x00000159,
}
})
...
}
The expression SMB0 is used to indicate SMBus HC#0,
a string of up to four characters.
Created the SMB0 object according to the following
specifications:
ACPI Specification
13.2. Accessing the SMBus from ASL Code
https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/13_ACPI_System_Mgmt_Bus_Interface_Spec/accessing-the-smbus-from-asl-code.html
IPMI Specification
Example 4: SSIF Interface(P574)
https://www.intel.co.jp/content/www/jp/ja/products/docs/servers/ipmi/ipmi-second-gen-interface-spec-v2-rev1-1.html
Signed-off-by: Yoshihiro Furudera <fj5100bi@fujitsu.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
There's no reason for this driver to use OF-specific property helpers.
Drop the last one in favor of the generic variant and no longer include
of.h.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
phydev->eee_cfg.eee_enabled
This is a follow-up to 41ffcd95015f ("net: phy: fix phylib's dual
eee_enabled") and resolves an issue with genphy_c45_an_config_eee_aneg()
(called from genphy_c45_ethtool_set_eee) not seeing the new value of
phydev->eee_cfg.eee_enabled.
Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
