summaryrefslogtreecommitdiff
path: root/include/drm/bridge
AgeCommit message (Collapse)Author
2024-10-17drm/bridge: synopsys: Add DW HDMI QP TX Controller support libraryCristian Ciocaltea
The Synopsys DesignWare HDMI 2.1 Quad-Pixel (QP) TX Controller IP supports the following features, among others: * Fixed Rate Link (FRL) * Display Stream Compression (DSC) * 4K@120Hz and 8K@60Hz video modes * Variable Refresh Rate (VRR) including Quick Media Switching (QMS), aka Cinema VRR * Fast Vactive (FVA), aka Quick Frame Transport (QFT) * SCDC I2C DDC access * TMDS Scrambler enabling 2160p@60Hz with RGB/YCbCr4:4:4 * YCbCr4:2:0 enabling 2160p@60Hz at lower HDMI link speeds * Multi-stream audio * Enhanced Audio Return Channel (EARC) Add library containing common helpers to enable basic support, i.e. RGB output up to 4K@30Hz, without audio, CEC or any HDMI 2.1 specific features. Co-developed-by: Algea Cao <algea.cao@rock-chips.com> Signed-off-by: Algea Cao <algea.cao@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20241016-b4-rk3588-bridge-upstream-v10-1-87ef92a6d14e@collabora.com Signed-off-by: Maxime Ripard <mripard@kernel.org>
2024-10-09drm/imx: add forward declarations for typesJani Nikula
The imx.h header does not forward declare the types it uses, and the header is not self-contained. Fix it. Fixes: cc3e8a216d6b ("drm/imx: add internal bridge handling display-timings DT node") Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: imx@lists.linux.dev Cc: linux-arm-kernel@lists.infradead.org Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Link: https://patchwork.freedesktop.org/patch/msgid/20241009140452.1981175-1-jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2024-09-03drm/imx: add internal bridge handling display-timings DT nodeDmitry Baryshkov
i.MX DRM DT bindings allow using either a proper panel / bridge graph to provide information about connected panels, or just a display-timings DT node, describing just the timings and the flags. Add helper bridge driver supporting the latter usecase. It will be used by both LDB and parallel-display drivers. Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Chris Healy <cphealy@gmail.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # on imx6q-nitrogen6x Link: https://patchwork.freedesktop.org/patch/msgid/20240602-drm-imx-cleanup-v3-9-e549e2a43100@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2024-06-27drm/bridge: analogix_dp: remove unused analogix_dp_removeLucas Stach
Now that the clock is handled dynamically through analogix_dp_resume/suspend and it isn't statically enabled in the driver probe routine, there is no need for the remove function anymore. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Robert Foss <rfoss@kernel.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-5-l.stach@pengutronix.de
2024-06-27drm/bridge: analogix_dp: remove unused platform power_on_end callbackLucas Stach
This isn't used, but gives the impression of the power on and power off platform calls being non-symmetrical. Remove the unused callback and rename the power_on_start to simply power_on. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Robert Foss <rfoss@kernel.org> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240619182200.3752465-1-l.stach@pengutronix.de
2024-05-22Merge tag 'usb-6.10-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB / Thunderbolt updates from Greg KH: "Here is the big set of USB and Thunderbolt changes for 6.10-rc1. Nothing hugely earth-shattering, just constant forward progress for hardware support of new devices and cleanups over the drivers. Included in here are: - Thunderbolt / USB 4 driver updates - typec driver updates - dwc3 driver updates - gadget driver updates - uss720 driver id additions and fixes (people use USB->arallel port devices still!) - onboard-hub driver rename and additions for new hardware - xhci driver updates - other small USB driver updates and additions for quirks and api changes All of these have been in linux-next for a while with no reported problems" * tag 'usb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits) drm/bridge: aux-hpd-bridge: correct devm_drm_dp_hpd_bridge_add() stub usb: fotg210: Add missing kernel doc description usb: dwc3: core: Fix unused variable warning in core driver usb: typec: tipd: rely on i2c_get_match_data() usb: typec: tipd: fix event checking for tps6598x usb: typec: tipd: fix event checking for tps25750 dt-bindings: usb: qcom,dwc3: fix interrupt max items usb: fotg210: Use *-y instead of *-objs in Makefile usb: phy: tegra: Replace of_gpio.h by proper one usb: typec: ucsi: displayport: Fix potential deadlock usb: typec: qcom-pmic-typec: split HPD bridge alloc and registration usb: musc: Remove unused list 'buffers' usb: dwc3: Wait unconditionally after issuing EndXfer command usb: gadget: u_audio: Clear uac pointer when freed. usb: gadget: u_audio: Fix race condition use of controls after free during gadget unbind. dt-bindings: usb: dwc3: Add QDU1000 compatible usb: core: Remove the useless struct usb_devmap which is just a bitmap MAINTAINERS: Remove {ehci,uhci}-platform.c from ARM/VT8500 entry USB: usb_parse_endpoint: ignore reserved bits usb: xhci: compact 'trb_in_td()' arguments ...
2024-05-11drm/bridge: aux-hpd-bridge: correct devm_drm_dp_hpd_bridge_add() stubDmitry Baryshkov
If CONFIG_DRM_AUX_HPD_BRIDGE is not enabled, the aux-bridge.h header provides a stub for the bridge's functions. Correct the arguments list of one of those stubs to match the argument list of the non-stubbed function. Fixes: e5ca263508f7 ("drm/bridge: aux-hpd: separate allocation and registration") Reported-by: kernel test robot <lkp@intel.com> Cc: stable <stable@kernel.org> Closes: https://lore.kernel.org/oe-kbuild-all/202405110428.TMCfb1Ut-lkp@intel.com/ Cc: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240511-fix-aux-hpd-stubs-v1-1-98dae71dfaec@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-05Merge tag 'drm-misc-next-2024-03-28' of ↵Dave Airlie
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next Two misc-next in one. drm-misc-next for v6.10-rc1: The deal of a lifetime! You get ALL of the previous drm-misc-next-2024-03-21-1 tag!! But WAIT, there's MORE! Cross-subsystem Changes: - Assorted DT binding updates. Core Changes: - Clarify how optional wait_hpd_asserted is. - Shuffle Kconfig names around. Driver Changes: - Assorted build fixes for panthor, imagination, - Add AUO B120XAN01.0 panels. - Assorted small fixes to panthor, panfrost. drm-misc-next for v6.10: UAPI Changes: - Move some nouveau magic constants to uapi. Cross-subsystem Changes: - Move drm-misc to gitlab and freedesktop hosting. - Add entries for panfrost. Core Changes: - Improve placement for TTM bo's in idle/busy handling. - Improve drm/bridge init ordering. - Add CONFIG_DRM_WERROR, and use W=1 for drm. - Assorted documentation updates. - Make more (drm and driver) headers self-contained and add header guards. - Grab reservation lock in pin/unpin callbacks. - Fix reservation lock handling for vmap. - Add edp and edid panel matching, use it to fix a nearly identical panel. Driver Changes: - Add drm/panthor driver and assorted fixes. - Assorted small fixes to xlnx, panel-edp, tidss, ci, nouveau, panel and bridge drivers. - Add Samsung s6e3fa7, BOE NT116WHM-N44, CMN N116BCA-EA1, CrystalClear CMT430B19N00, Startek KD050HDFIA020-C020A, powertip PH128800T006-ZHC01 panels. - Fix console for omapdrm. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/bea310a6-6ff6-477e-9363-f9f053cfd12a@linux.intel.com
2024-03-07drm: bridge: samsung-dsim: make samsung-dsim.h self-containedJani Nikula
Include <drm/drm_bridge.h> and forward declare struct platform device. Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/9534ca7dfba96580950e116c84ce0fa68fdf93a4.1709749576.git.jani.nikula@intel.com
2024-02-23drm/bridge: aux-hpd: separate allocation and registrationJohan Hovold
Combining allocation and registration is an anti-pattern that should be avoided. Add two new functions for allocating and registering an dp-hpd bridge with a proper 'devm' prefix so that it is clear that these are device managed interfaces. devm_drm_dp_hpd_bridge_alloc() devm_drm_dp_hpd_bridge_add() The new interface will be used to fix a use-after-free bug in the Qualcomm PMIC GLINK driver and may prevent similar issues from being introduced elsewhere. The existing drm_dp_hpd_bridge_register() is reimplemented using the above and left in place for now. Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240217150228.5788-3-johan+linaro@kernel.org
2023-12-07drm/bridge: Return NULL instead of plain 0 in drm_dp_hpd_bridge_register() stubNathan Chancellor
sparse complains: drivers/usb/typec/tcpm/qcom/qcom_pmic_typec.c: note: in included file: include/drm/bridge/aux-bridge.h:29:16: sparse: sparse: Using plain integer as NULL pointer Return NULL to clear up the warning. Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312060025.BdeqZrWx-lkp@intel.com/ Fixes: e560518a6c2e ("drm/bridge: implement generic DP HPD bridge") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20231205-drm_aux_bridge-fixes-v1-3-d242a0ae9df4@kernel.org
2023-12-04drm/bridge: implement generic DP HPD bridgeDmitry Baryshkov
Several USB-C controllers implement a pretty simple DRM bridge which implements just the HPD notification operations. Add special helper for creating such simple bridges. Acked-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20231203114333.1305826-5-dmitry.baryshkov@linaro.org
2023-12-04drm/bridge: add transparent bridge helperDmitry Baryshkov
Define a helper for creating simple transparent bridges which serve the only purpose of linking devices into the bridge chain up to the last bridge representing the connector. This is especially useful for DP/USB-C bridge chains, which can span across several devices, but do not require any additional functionality from the intermediate bridges. Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20231203114333.1305826-2-dmitry.baryshkov@linaro.org
2023-10-16drm/bridge: synopsys: dw-mipi-dsi: Add mode fixup supportLiu Ying
Vendor drivers may need to fixup mode due to pixel clock tree limitation, so introduce the ->mode_fixup() callcack to struct dw_mipi_dsi_plat_data and call it at atomic check stage if available. Signed-off-by: Liu Ying <victor.liu@nxp.com> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-5-victor.liu@nxp.com
2023-10-16drm/bridge: synopsys: dw-mipi-dsi: Add input bus format negotiation supportLiu Ying
Introduce ->get_input_bus_fmts() callback to struct dw_mipi_dsi_plat_data so that vendor drivers can implement specific methods to get input bus formats for Synopsys DW MIPI DSI. While at it, implement a generic callback for ->atomic_get_input_bus_fmts(), where we try to get the input bus formats through pdata->get_input_bus_fmts() first. If it's unavailable, fall back to the only format - MEDIA_BUS_FMT_FIXED, which matches the default behavior if ->atomic_get_input_bus_fmts() is not implemented as ->atomic_get_input_bus_fmts()'s kerneldoc indicates. Signed-off-by: Liu Ying <victor.liu@nxp.com> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-3-victor.liu@nxp.com
2023-10-16drm/bridge: synopsys: dw-mipi-dsi: Add dw_mipi_dsi_get_bridge() helperLiu Ying
Add dw_mipi_dsi_get_bridge() helper so that it can be used by vendor drivers which implement vendor specific extensions to Synopsys DW MIPI DSI. Signed-off-by: Liu Ying <victor.liu@nxp.com> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-2-victor.liu@nxp.com
2023-10-09drm/bridge: samsung-dsim: update PLL reference clockMichael Tretter
The PLL requires a clock frequency in a certain platform-dependent range after the pre-divider. The reference clock for the PLL may change due to changes to it's parent clock. Thus, the frequency may be out of range or unsuited for generating the high speed clock for MIPI DSI. Try to keep the pre-devider small, and set the reference clock close to the upper limit before recalculating the PLL configuration. Use a divider with a power of two for the reference clock as this seems to work best in my tests. Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL i.MX8MM + Waveshare 10.1inch HDMI LCD (E) Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20230818-samsung-dsim-v2-3-846603df0e0a@pengutronix.de Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230818-samsung-dsim-v2-3-846603df0e0a@pengutronix.de
2023-10-09drm/bridge: samsung-dsim: reread ref clock before configuring PLLMichael Tretter
The PLL reference clock may change at runtime when its parent clock changes. For example, this may happen on the i.MX8M Nano if the reference clock is a child of the Video PLL. If the pixel clock changes, this may propagate to the Video PLL and as a side effect change the reference clock. Thus, reading the clock rate during probe is not sufficient to correctly configure the PLL for the expected hs clock. Read the actual rate of the reference clock before calculating the PLL configuration parameters. Note that the "samsung,pll-clock-frequency" is always preferred and PLL reference clock is only read from the clock tree if that device tree property is not set. Reviewed-by: Inki Dae <inki.dae@samsung.com> Acked-by: Inki Dae <inki.dae@samsung.com> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL i.MX8MM + Waveshare 10.1inch HDMI LCD (E) Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20230818-samsung-dsim-v2-2-846603df0e0a@pengutronix.de Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230818-samsung-dsim-v2-2-846603df0e0a@pengutronix.de
2023-10-06drm: exynos: dsi: Convert to platform remove callback returning voidUwe Kleine-König
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). samsung_dsim_remove() returned 0 unconditionally. Make it return void instead to convert the two related platform drivers to use .remove_new(). Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Inki Dae <inki.dae@samsung.com> Acked-by: Inki Dae <inki.dae@samsung.com> Link: https://lore.kernel.org/r/20230919103939.1367659-1-u.kleine-koenig@pengutronix.de Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230919103939.1367659-1-u.kleine-koenig@pengutronix.de
2023-08-11drm: bridge: samsung-dsim: Fix waiting for empty cmd transfer FIFO on older ↵Marek Szyprowski
Exynos Samsung DSIM used in older Exynos SoCs (like Exynos 4210, 4x12, 3250) doesn't report empty level of packer header FIFO. In case of those SoCs, use the old way of waiting for empty command tranfsfer FIFO, removed recently by commit 14806c641582 ("drm: bridge: samsung-dsim: Drain command transfer FIFO before transfer"). Fixes: 14806c641582 ("drm: bridge: samsung-dsim: Drain command transfer FIFO before transfer") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230809145641.3213210-1-m.szyprowski@samsung.com
2023-06-27drm/bridge: dw-hdmi: change YUV420 selection logic at clock setupAdrián Larumbe
Right now clocking value selection code is prioritising RGB, YUV444 modes over YUV420 for HDMI2 sinks. However, because of the bus format selection procedure in dw-hdmi, for HDMI2 sinks YUV420 is the format that will always be picked during the drm bridge chain check stage. Later on dw_hdmi_setup will configure a colour space based on the bus format that doesn't match the pixel value we had calculated as described above. Fix it by bringing back dw-hdmi bus format check when picking the right pixel clock. Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com> Acked-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/6230bfae2cd97cf6527fc62ba5c850464919ccf8.1687702042.git.adrian.larumbe@collabora.com
2023-05-26drm: bridge: samsung-dsim: Dynamically configure DPHY timingAdam Ford
The DPHY timings are currently hard coded. Since the input clock can be variable, the phy timings need to be variable too. To facilitate this, we need to cache the hs_clock based on what is generated from the PLL. The phy_mipi_dphy_get_default_config_for_hsclk function configures the DPHY timings in pico-seconds, and a small macro converts those timings into clock cycles based on the hs_clk. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Michael Walle <michael@walle.cc> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-6-aford173@gmail.com
2023-05-26drm: bridge: samsung-dsim: Fix PMS Calculator on imx8m[mnp]Adam Ford
According to Table 13-45 of the i.MX8M Mini Reference Manual, the min and max values for M and the frequency range for the VCO_out calculator were incorrect. This information was contradicted in other parts of the mini, nano and plus manuals. After reaching out to my NXP Rep, when confronting him about discrepencies in the Nano manual, he responded with: "Yes it is definitely wrong, the one that is part of the NOTE in MIPI_DPHY_M_PLLPMS register table against PMS_P, PMS_M and PMS_S is not correct. I will report this to Doc team, the one customer should be take into account is the Table 13-40 DPHY PLL Parameters and the Note above." These updated values also match what is used in the NXP downstream kernel. To fix this, make new variables to hold the min and max values of m and the minimum value of VCO_out, and update the PMS calculator to use these new variables instead of using hard-coded values to keep the backwards compatibility with other parts using this driver. Fixes: 4d562c70c4dc ("drm: bridge: samsung-dsim: Add i.MX8M Mini/Nano support") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-3-aford173@gmail.com
2023-05-22drm: bridge: samsung-dsim: Implement support for clock/data polarity swapMarek Vasut
Implement support for DSI clock and data lane DN/DP polarity swap by means of decoding 'lane-polarities' DT property. The controller does support DN/DP swap of clock lane and all data lanes, the controller does not support polarity swap of individual data lane bundles, add a check which verifies all data lanes have the same polarity. This has been validated on an imx8mm board that actually has the MIPI DSI clock lanes inverted. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230514114625.98372-2-festevam@gmail.com
2023-03-28drm: bridge: samsung-dsim: Add i.MX8M Plus supportMarek Vasut
Add extras to support i.MX8M Plus. The main change is the removal of HS/VS/DE signal inversion in the LCDIFv3-DSIM glue logic, otherwise the implementation of this IP in i.MX8M Plus is very much compatible with the i.MX8M Mini/Nano one. Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Acked-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Inki Dae <m.szyprowski@samsung.com>
2023-03-28drm: bridge: Generalize Exynos-DSI driver into a Samsung DSIM bridgeJagan Teki
Samsung MIPI DSIM controller is common DSI IP that can be used in various SoCs like Exynos, i.MX8M Mini/Nano. In order to access this DSI controller between various platform SoCs, the ideal way to incorporate this in the drm stack is via the drm bridge driver. We already have a consolidated code for supporting component and bridge based DRM drivers, so keep the exynos component based code in existing exynos_drm_dsi.c and move generic bridge code as part of samsung-dsim.c Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
2022-04-19drm: bridge: dw_hdmi: Audio: Add General Parallel Audio (GPA) driverSandor Yu
General Parallel Audio (GPA) interface is one of the supported audio interface for synopsys HDMI module, which has verified for i.MX8MPlus platform. This is initial version for GPA. Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Signed-off-by: Sandor Yu <Sandor.yu@nxp.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/f21ba3e8c4d9d028ac74c6f3c588ddbffe739399.1649989179.git.Sandor.yu@nxp.com
2022-04-19drm: bridge: dw_hdmi: add reset function for PHY GEN1Sandor Yu
PHY reset register(MC_PHYRSTZ) active high reset control for PHY GEN2, and active low reset control for PHY GEN1. Rename function dw_hdmi_phy_reset to dw_hdmi_phy_gen2_reset. Add dw_hdmi_phy_gen1_reset function for PHY GEN1. Signed-off-by: Sandor Yu <Sandor.yu@nxp.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/e0b3be2d63fe3e95246fb8b8b0dcd57415b29e04.1649989179.git.Sandor.yu@nxp.com
2022-01-04drm/bridge/synopsys: dsi: extend the prototype of mode_valid()Antonio Borneo
To evaluate the validity of a video mode, some additional internal value has to be passed to the platform implementation. Extend the prototype of mode_valid(). Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com> Reviewed-by: Philippe Cornu <philippe.cornu@foss.st.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211218215055.212421-2-antonio.borneo@foss.st.com
2021-07-28drm: bridge: dw-hdmi: Attach to next bridge if availableLaurent Pinchart
On all platforms except i.MX and Rockchip, the dw-hdmi DT bindings require a video output port connected to an HDMI sink (most likely an HDMI connector, in rare cases another bridges converting HDMI to another protocol). For those platforms, retrieve the next bridge and attach it from the dw-hdmi bridge attach handler. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
2021-04-20drm/bridge/synopsys: dw-hdmi: Add an option to suppress loading CEC driverJernej Skrabec
This adds DW-HDMI driver a glue option to disable loading of the CEC sub-driver. On some SoCs, the CEC functionality is enabled in the IP config bits, but the CEC bus is non-functional like on Amlogic SoCs, where the CEC config bit is set but the DW-HDMI CEC signal is not connected to a physical pin, leading to some confusion when the DW-HDMI CEC controller can't communicate on the bus. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Link: https://patchwork.freedesktop.org/patch/msgid/20210416092737.1971876-2-narmstrong@baylibre.com
2020-09-11drm/bridge: dw-mipi-dsi: permit configuring the escape clock rateNeil Armstrong
The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency higher than 10MHz for the TX Escape Clock, thus make the target rate configurable. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200904125531.15248-1-narmstrong@baylibre.com
2020-06-23drm: bridge: dw-hdmi: Pass drm_display_info to dw_hdmi_support_scdc()Laurent Pinchart
To prepare for making connector creation optional in the driver, pass the drm_display_info explicitly to dw_hdmi_support_scdc(). The pointer is passed to the callers where required, particularly to the dw_hdmi_phy_ops .init() function. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-19-laurent.pinchart+renesas@ideasonboard.com
2020-06-23drm: bridge: dw-hdmi: Constify mode argument to dw_hdmi_phy_ops .init()Laurent Pinchart
The PHY .init() must not modify the mode it receives. Make the pointer const to enfore that. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-17-laurent.pinchart+renesas@ideasonboard.com
2020-06-23drm: bridge: dw-hdmi: Pass drm_display_info to .mode_valid()Laurent Pinchart
Replace the drm_connector pointer passed to the .mode_valid() function with a const drm_display_info pointer, as that's all the function should need. Use the display info passed to the bridge .mode_valid() operation instead of retrieving it from the connector, to prepare for make connector creation optional. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-16-laurent.pinchart+renesas@ideasonboard.com
2020-06-23drm: bridge: dw-hdmi: Remove unused field from dw_hdmi_plat_dataLaurent Pinchart
The input_bus_format field of struct dw_hdmi_plat_data is unused. Remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-14-laurent.pinchart+renesas@ideasonboard.com
2020-06-23drm: bridge: dw-hdmi: Pass private data pointer to .configure_phy()Laurent Pinchart
The .configure_phy() operation takes a dw_hdmi_plat_data pointer as a context argument. This differs from .mode_valid() that takes a custom private context pointer, causing possible confusion. Make the dw_hdmi_plat_data operations more consistent by passing the private context pointer to .configure_phy() as well. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-13-laurent.pinchart+renesas@ideasonboard.com
2020-06-23drm: bridge: dw-hdmi: Pass private data pointer to .mode_valid()Laurent Pinchart
Platform glue drivers for dw_hdmi may need to access device-specific data from their .mode_valid() implementation. They currently have no clean way to do so, and one driver hacks around it by accessing the dev_private data of the drm_device retrieved from the connector. Add a priv_data void pointer to the dw_hdmi_plat_data structure, and pass it to the .mode_valid() function. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-12-laurent.pinchart+renesas@ideasonboard.com
2020-04-09drm/bridge: analogix_dp: Split bind() into probe() and real bind()Marek Szyprowski
Analogix_dp driver acquires all its resources in the ->bind() callback, what is a bit against the component driver based approach, where the driver initialization is split into a probe(), where all resources are gathered, and a bind(), where all objects are created and a compound driver is initialized. Extract all the resource related operations to analogix_dp_probe() and analogix_dp_remove(), then call them before/after registration of the device components from the main Exynos DP and Rockchip DP drivers. Also move the plat_data initialization to the probe() to make it available for the analogix_dp_probe() function. This fixes the multiple calls to the bind() of the DRM compound driver when the DP PHY driver is not yet loaded/probed: [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops [exynosdrm]) exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm]) exynos-dp 145b0000.dp-controller: no DP phy configured exynos-drm exynos-drm: failed to bind 145b0000.dp-controller (ops exynos_dp_ops [exynosdrm]): -517 exynos-drm exynos-drm: master bind failed: -517 ... [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) exynos-drm exynos-drm: bound 145b0000.dp-controller (ops hdmi_enable [exynosdrm]) exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). Console: switching to colour frame buffer device 170x48 exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer device [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1 ... Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200310103427.26048-1-m.szyprowski@samsung.com (cherry picked from commit 83a196773b8bc6702f49df1eddc848180e350340) Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2020-03-10drm/bridge: synopsys: dw-hdmi: allow ycbcr420 modes for >= 0x200aNeil Armstrong
Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support for these modes in the connector if the platform supports them. We limit these modes to DW-HDMI IP version >= 0x200a which are designed to support HDMI2.0 display modes. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net> Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-6-narmstrong@baylibre.com
2020-03-06drm/bridge/mhl.h: Replace zero-length array with flexible-array memberGustavo A. R. Silva
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200305110011.GA21056@embeddedor
2020-01-03Merge tag 'drm-misc-next-2020-01-02' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for v5.6: UAPI Changes: - Commandline parser: Add support for panel orientation, and per-mode options. - Fix IOCTL naming for dma-buf heaps. Cross-subsystem Changes: - Rename DMA_HEAP_IOC_ALLOC to DMA_HEAP_IOCTL_ALLOC before it becomes abi. - Change DMA-BUF system-heap's name to system. - Fix leak in error handling in dma_heap_ioctl(), and make a symbol static. - Fix udma-buf cpu access. - Fix ti devicetree bindings. Core Changes: - Add CTA-861-G modes with VIC >= 193. - Change error handling and remove bug_on in *drm_dev_init. - Export drm_panel_of_backlight() correctly once more. - Add support for lvds decoders. - Convert drm/client and drm/(gem-,)fb-helper to drm-device based logging and update logging todo. Driver Changes: - Add support for dsi/px30 to rockchip. - Add fb damage support to virtio. - Use dma_resv locking wrappers in vc4, msm, etnaviv. - Make functions in virtio static, and perform some simplifications. - Add suspend support to sun4i. - Add A64 mipi dsi support to sun4i. - Add runtime pm suspend to komeda. - Associated driver fixes. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/efc11139-1653-86bc-1b0f-0aefde219850@linux.intel.com
2019-12-16drm/bridge/synopsys: dsi: driver-specific configuration of phy timingsHeiko Stuebner
The timing values for dw-dsi are often dependent on the used display and according to Philippe Cornu will most likely also depend on the used phy technology in the soc-specific implementation. To solve this and allow specific implementations to define them as needed add a new get_timing callback to phy_ops and call this from the dphy_timing function to retrieve the necessary values for the specific mode. Right now this handles the hs2lp + lp2hs where Rockchip SoCs need handling according to the phy speed, while STM seems to be ok with static values. changes in v5: - rebase on 5.5-rc1 - merge into px30 dsi series to prevent ordering conflicts changes in v4: - rebase to make it directly fit on top of drm-misc-next after all changes in v3: - check existence of phy_ops->get_timing in __dw_mipi_dsi_probe() - emit actual error when get_timing() call fails - add tags from Philippe and Yannick changes in v2: - add driver-specific handling, don't force all bridge users to use the same timings, as suggested by Philippe Suggested-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Yannick Fertre <yannick.fertre@st.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-2-heiko@sntech.de
2019-11-27Merge tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm updates from Dave Airlie: "Lots of stuff in here, though it hasn't been too insane this merge apart from dealing with the security fun. uapi: - export different colorspace properties on DP vs HDMI - new fourcc for ARM 16x16 block format - syncobj: allow querying last submitted timeline value - DRM_FORMAT_BIG_ENDIAN defined as unsigned core: - allow using gem vma manager in ttm - connector/encoder/bridge doc fixes - allow more than 3 encoders for a connector - displayport mst suspend/resume reprobing support - vram lazy unmapping, uniform vram mm and gem vram - edid cleanups + AVI informframe bar info - displayport helpers - dpcd parser added dp_cec: - Allow a connector to be associated with a cec device ttm: - pipelining with no_gpu_wait fix - always keep BOs on the LRU sched: - allow free_job routine to sleep i915: - Block userptr from mappable GTT - i915 perf uapi versioning - OA stream dynamic reconfiguration - make context persistence optional - introduce DRM_I915_UNSTABLE Kconfig - add fake lmem testing under unstable - BT.2020 support for DP MSA - struct mutex elimination - Tigerlake display/PLL/power management improvements - Jasper Lake PCH support - refactor PMU for multiple GPUs - Icelake firmware update - Split out vga + switcheroo code amdgpu: - implement dma-buf import/export without helpers - vega20 RAS enablement - DC i2c over aux fixes - renoir GPU reset - DC HDCP support - BACO support for CI/VI asics - MSI-X support - Arcturus EEPROM support - Arcturus VCN encode support - VCN dynamic powergating on RV/RV2 amdkfd: - add navi12/14/renoir support to kfd radeon: - SI dpm fix ported from amdgpu - fix bad DMA on ppc platforms gma500: - memory leak fixes qxl: - convert to new gem mmap exynos: - build warning fix komeda: - add aclk sysfs attribute v3d: - userspace cleanup uapi change i810: - fix for underflow in dispatch ioctls ast: - refactor show_cursor mgag200: - refactor show_cursor arcgpu: - encoder finding improvements mediatek: - mipi_tx, dsi and partial crtc support for MT8183 SoC - rotation support meson: - add suspend/resume support omap: - misc refactors tegra: - DisplayPort support for Tegra 210, 186 and 194. - IOMMU-backed DMA API fixes panfrost: - fix lockdep issue - simplify devfreq integration rcar-du: - R8A774B1 SoC support - fixes for H2 ES2.0 sun4i: - vcc-dsi regulator support virtio-gpu: - vmexit vs spinlock fix - move to gem shmem helpers - handle large command buffers with cma" * tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits) drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10 drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF. drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF drm/amdgpu/gfx10: re-init clear state buffer after gpu reset merge fix for "ftrace: Rework event_create_dir()" drm/amdgpu: Update Arcturus golden registers drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt Revert "drm/amd/display: enable S/G for RAVEN chip" drm/amdgpu: disable gfxoff on original raven drm/amdgpu: remove experimental flag for Navi14 drm/amdgpu: disable gfxoff when using register read interface drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2) drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2 drm/radeon: fix bad DMA from INTERRUPT_CNTL2 drm/amd/display: Fix debugfs on MST connectors drm/amdgpu/nv: add asic func for fetching vbios from rom directly drm/amdgpu: put flush_delayed_work at first drm/amdgpu/vcn2.5: fix the enc loop with hw fini ...
2019-10-29drm: bridge: dw-hdmi: Report connector status using callbackCheng-Yi Chiang
Allow codec driver register callback function for plug event. The callback registration flow: dw-hdmi <--- hw-hdmi-i2s-audio <--- hdmi-codec dw-hdmi-i2s-audio implements hook_plugged_cb op so codec driver can register the callback. dw-hdmi exports a function dw_hdmi_set_plugged_cb so platform device can register the callback. When connector plug/unplug event happens, report this event using the callback. Make sure that audio and drm are using the single source of truth for connector status. Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Link: https://lore.kernel.org/r/20191028071930.145899-2-cychiang@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org>
2019-10-10drm/bridge: dw-hdmi: Add Dynamic Range and Mastering InfoFrame supportJonas Karlman
Add support for configuring Dynamic Range and Mastering InfoFrame from the hdr_output_metadata connector property. This patch adds a use_drm_infoframe flag to dw_hdmi_plat_data that platform drivers use to signal when Dynamic Range and Mastering infoframes is supported. This flag is needed because Amlogic GXBB and GXL report same DW-HDMI version, and only GXL support DRM InfoFrame. These changes were based on work done by Zheng Yang <zhengyang@rock-chips.com> to support DRM InfoFrame on the Rockchip 4.4 BSP kernel at [1] and [2] [1] https://github.com/rockchip-linux/kernel/tree/develop-4.4 [2] https://github.com/rockchip-linux/kernel/commit/d1943fde81ff41d7cca87f4a42f03992e90bddd5 Cc: Zheng Yang <zhengyang@rock-chips.com> Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/HE1PR06MB4011D7B916CBF8B740ACC45FAC9B0@HE1PR06MB4011.eurprd06.prod.outlook.com
2019-09-13drm: bridge/dw_hdmi: add audio sample channel status settingYakir Yang
When transmitting IEC60985 linear PCM audio, we configure the Aduio Sample Channel Status information in the IEC60958 frame. The status bit is already available in iec.status of hdmi_codec_params. This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241) Note that these registers are only for interfaces: I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA (AHBAUDDMA). For S/PDIF interface this information comes from the stream. Currently this function dw_hdmi_set_channel_status is only called from dw-hdmi-i2s-audio in I2S setup. Signed-off-by: Yakir Yang <ykk@rock-chips.com> Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org> Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190911082646.134347-1-cychiang@chromium.org
2019-08-14drm/bridge: dw-hdmi: move audio channel setup out of ahbJerome Brunet
Part of the channel count setup done in dw-hdmi ahb should actually be done whatever the interface providing the data. Let's move it to dw-hdmi driver instead. Reviewed-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-3-jbrunet@baylibre.com
2019-07-26drm/rockchip: Use the helpers for PSRSean Paul
Instead of rolling our own implementation for tracking when PSR should be [in]active, use the new self refresh helpers to do the heavy lifting. Changes in v2: - updated to reflect changes made in the helpers Changes in v3: - use the new atomic hooks to inspect crtc state instead of needing conn state (Daniel) Changes in v4: - Use Laurent's get_new_connector_for_encoder helper (Daniel) - Exit vop disable early if it's already off Changes in v5: - Rebase on latest drm-misc-next - Resolve conflict with s/edp_vsc_psr/dp_sdp/ rename - Resolve conflict with drm_atomic.h header inclusion Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-4-sean@poorly.run Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-3-sean@poorly.run Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-9-sean@poorly.run Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-9-sean@poorly.run Cc: Zain Wang <wzz@rock-chips.com> Cc: Tomasz Figa <tfiga@chromium.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Heiko Stuebner <heiko@sntech.de> [seanpaul resolved some conflicts with drmP.h work and Helen's async fixes] Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-9-sean@poorly.run
2019-07-15Merge tag 'drm-next-2019-07-16' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm updates from Dave Airlie: "The biggest thing in this is the AMD Navi GPU support, this again contains a bunch of header files that are large. These are the new AMD RX5700 GPUs that just recently became available. New drivers: - ST-Ericsson MCDE driver - Ingenic JZ47xx SoC UAPI change: - HDR source metadata property Core: - HDR inforframes and EDID parsing - drm hdmi infoframe unpacking - remove prime sg_table caching into dma-buf - New gem vram helpers to reduce driver code - Lots of drmP.h removal - reservation fencing fix - documentation updates - drm_fb_helper_connector removed - mode name command handler rewrite fbcon: - Remove the fbcon notifiers ttm: - forward progress fixes dma-buf: - make mmap call optional - debugfs refcount fixes - dma-fence free with pending signals fix - each dma-buf gets an inode Panels: - Lots of additional panel bindings amdgpu: - initial navi10 support - avoid hw reset - HDR metadata support - new thermal sensors for vega asics - RAS fixes - use HMM rather than MMU notifier - xgmi topology via kfd - SR-IOV fixes - driver reload fixes - DC use a core bpc attribute - Aux fixes for DC - Bandwidth calc updates for DC - Clock handling refactor - kfd VEGAM support vmwgfx: - Coherent memory support changes i915: - HDR Support - HDMI i2c link - Icelake multi-segmented gamma support - GuC firmware update - Mule Creek Canyon PCH support for EHL - EHL platform updtes - move i915.alpha_support to i915.force_probe - runtime PM refactoring - VBT parsing refactoring - DSI fixes - struct mutex dependency reduction - GEM code reorg mali-dp: - Komeda driver features msm: - dsi vs EPROBE_DEFER fixes - msm8998 snapdragon 835 support - a540 gpu support - mdp5 and dpu interconnect support exynos: - drmP.h removal tegra: - misc fixes tda998x: - audio support improvements - pixel repeated mode support - quantisation range handling corrections - HDMI vendor info fix armada: - interlace support fix - overlay/video plane register handling refactor - add gamma support rockchip: - RX3328 support panfrost: - expose perf counters via hidden ioctls vkms: - enumerate CRC sources list ast: - rework BO handling mgag200: - rework BO handling dw-hdmi: - suspend/resume support rcar-du: - R8A774A1 Soc Support - LVDS dual-link mode support - Additional formats - Misc fixes omapdrm: - DSI command mode display support stm - fb modifier support - runtime PM support sun4i: - use vmap ops vc4: - binner bo binding rework v3d: - compute shader support - resync/sync fixes - job management refactoring lima: - NULL pointer in irq handler fix - scheduler default timeout virtio: - fence seqno support - trace events bochs: - misc fixes tc458767: - IRQ/HDP handling sii902x: - HDMI audio support atmel-hlcdc: - misc fixes meson: - zpos support" * tag 'drm-next-2019-07-16' of git://anongit.freedesktop.org/drm/drm: (1815 commits) Revert "Merge branch 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux into drm-next" Revert "mm: adjust apply_to_pfn_range interface for dropped token." mm: adjust apply_to_pfn_range interface for dropped token. drm/amdgpu/navi10: add uclk activity sensor drm/amdgpu: properly guard the generic discovery code drm/amdgpu: add missing documentation on new module parameters drm/amdgpu: don't invalidate caches in RELEASE_MEM, only do the writeback drm/amd/display: avoid 64-bit division drm/amdgpu/psp11: simplify the ucode register logic drm/amdgpu: properly guard DC support in navi code drm/amd/powerplay: vega20: fix uninitialized variable use drm/amd/display: dcn20: include linux/delay.h amdgpu: make pmu support optional drm/amd/powerplay: Zero initialize current_rpm in vega20_get_fan_speed_percent drm/amd/powerplay: Zero initialize freq in smu_v11_0_get_current_clk_freq drm/amd/powerplay: Use memset to initialize metrics structs drm/amdgpu/mes10.1: Fix header guard drm/amd/powerplay: add temperature sensor support for navi10 drm/amdgpu: fix scheduler timeout calc drm/amdgpu: Prepare for hmm_range_register API change (v2) ...
generated by cgit v1.2.3-70-g09d2 (git 2.47.1) at 2025-02-07 08:40:20 +0000