| Age | Commit message (Collapse) | Author |
|---|
|
Clarify the difference between "interface" and "phy_interface" in
struct plat_stmmacenet_data, both by adding a comment, and also
renaming "interface" to be "mac_interface". The difference between
these are:
MAC ----- optional PCS ----- SerDes ----- optional PHY ----- Media
^ ^
mac_interface phy_interface
Note that phylink currently only deals with phy_interface.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZq83-005tts-6K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All users of plat->phylink_node first convert it to a fwnode. Rather
than repeatedly convert to a fwnode, store it as a fwnode. To reflect
this change, call it plat->port_node instead - it is used for more
than just phylink.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAX8-005pTo-OT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A mode parameter has been added to the callback function of fix_mac_speed
to indicate the physical layer type.
The mode can be one the following:
MLO_AN_PHY - Conventional PHY
MLO_AN_FIXED - Fixed-link mode
MLO_AN_INBAND - In-band protocol
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230807160716.259072-2-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IEEE1588 Standard specifies that the timestamps of Packets must be
captured when the PTP message timestamp point (leading edge of first
octet after the start of frame delimiter) crosses the boundary between
the node and the network. As the MAC latches the timestamp at an
internal point, the captured timestamp must be corrected for the
additional data transmission latency, as described in the publicly
available datasheet [1].
This patch only corrects for the MAC-Internal delay, which can be read
out from the MAC_Ingress_Timestamp_Latency register on DWMAC version 5,
since the Phy framework currently does not support querying the Phy
ingress and egress latency. The Closs Domain Crossing Circuits errors as
indicated in [1] are already being accounted in the
stmmac_get_tx_hwtstamp() function and are not corrected here.
As the Latency varies for different link speeds and MII
modes of operation, the correction value needs to be updated on each
link state change.
As the delay also causes a phase shift in the timestamp counter compared
to the rest of the network, this correction will also reduce phase error
when generating PPS outputs from the timestamp counter.
Since the correction registers may be unavailable on some hardware and
no feature bits are documented for dynamically detection of the MAC
propagation delay readout, introduce a feature bit to explicitely enable
MAC delay Correction in the gluecode driver.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v2-1-3366f38ee9a6@pengutronix.de
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v3-1-61e63427735e@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The priv variable is _always_ of type (struct stmmac_priv *), so let's
stop using (void *) since it isn't abstracting anything.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230725211853.895832-3-ahalaney@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-13-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-12-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-11-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-10-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-9-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-8-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-7-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-6-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-5-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-4-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-3-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct plat_stmmacenet_data contains several boolean fields that could be
easily replaced with a common integer 'flags' bitfield and bit defines.
Start the process with the has_integrated_pcs field.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-2-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On some platforms, the PCS can be integrated in the MAC so the driver
will not see any PCS link activity. Add a switch that allows the platform
drivers to let the core code know.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some platforms have dwmac4 implementations that have a different
address space layout than the default, resulting in the need to define
their own DMA/MTL offsets.
Extend the functions to allow a platform driver to indicate what its
addresses are, overriding the defaults.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch adds support for platform-specific reset logic in the
stmmac driver. Some SoCs require a different reset mechanism than
the standard dwmac IP reset. To support these platforms, a new function
pointer 'fix_soc_reset' is added to the plat_stmmacenet_data structure.
The stmmac_reset in hwif.h is modified to call the 'fix_soc_reset'
function if it exists. This enables the driver to use the platform-specific
reset logic when necessary.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230403222302.328262-1-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently DMA address width is either read from a RO device register
or force set from the platform data. This breaks DMA when the host DMA
address width is <=32it but the device is >32bit.
Right now the driver may decide to use a 2nd DMA descriptor for
another buffer (happens in case of TSO xmit) assuming that 32bit
addressing is used due to platform configuration but the device will
still use both descriptor addresses as one address.
This can be observed with the Intel EHL platform driver that sets
32bit for addr64 but the MAC reports 40bit. The TX queue gets stuck in
case of TCP with iptables NAT configuration on TSO packets.
The logic should be like this: Whatever we do on the host side (memory
allocation GFP flags) should happen with the host DMA width, whenever
we decide how to set addresses on the device registers we must use the
device DMA address width.
This patch renames the platform address width field from addr64 (term
used in device datasheet) to host_addr and uses this value exclusively
for host side operations while all chip operations consider the device
DMA width as read from the device register.
Fixes: 7cfc4486e7ea ("stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing")
Signed-off-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.
Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tegra MGBE ethernet controller requires that the SERDES link is
powered-up after the PHY link is up, otherwise the link fails to
become ready following a resume from suspend. Add a variable to indicate
that the SERDES link must be powered-up after the PHY link.
Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'has_crossts' flag was not used anywhere in the stmmac driver,
removing it from both header file and dwmac-intel driver.
Signed-off-by: Wong Vee Khee <veekhee@apple.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20220817064324.10025-1-veekhee@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using current implementation of polling mode, there is high chances we
will hit into timeout error when running phc2sys. Hence, update the
implementation of hardware crosstimestamping to use the MAC interrupt
service routine instead of polling for TSIS bit in the MAC Timestamp
Interrupt Status register to be set.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.
So, disable the Split Header for Intel platforms.
v2: Add fixes tag in commit message.
Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dwmac-qcom-ethqos currently exposes a mechanism to dump rgmii registers
after the 'stmmac_dvr_probe()' returns. However with commit
5ec55823438e ("net: stmmac: add clocks management for gmac driver"),
we now let 'pm_runtime_put()' disable the clocks before returning from
'stmmac_dvr_probe()'.
This causes a crash when 'rgmii_dump()' register dumps are enabled,
as the clocks are already off.
Since other dwmac drivers (possible future users as well) might
require a similar register dump feature, introduce a platform level
callback to allow the same.
This fixes the crash noticed while enabling rgmii_dump() dumps in
dwmac-qcom-ethqos driver as well. It also allows future changes
to keep a invoking the register dump callback from the correct
place inside 'stmmac_dvr_probe()'.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clock domain crossing error (CDC) is calculated at every fetch of Tx or Rx
timestamps. It includes a division. Especially on arm32 based systems it is
expensive. It also requires two conditionals in the hotpath.
Add a compensation value cache to struct plat_stmmacenet_data and subtract it
unconditionally in the RX/TX functions which spares the conditionals.
The value is initialized to 0 and if supported calculated in the PTP
initialization code.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211122111931.135135-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After adjusting the ptp time, the Qbv base time may be the past time
of the new current time. dwmac5 hardware limited the base time cannot
be set as past time. This patch add a btr_reserve to store the base
time get from qopt, then calculate the base time and reset the Qbv
configuration after ptp time adjust.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current stmmac driver WOL implementation will enable MAC WOL
if MAC HW PMT feature is on. Else, the driver will check for
PHY WOL support. There is another case where MAC HW PMT is
enabled but the platform still goes for the PHY WOL option.
E.g, Intel platform are designed for PHY WOL but not MAC WOL
although HW MAC PMT features are enabled.
Introduce use_phy_wol platform data to select PHY WOL
instead of depending on HW PMT features. Set use_phy_wol
will disable the plat->pmt which currently used to
determine the system to wake up by MAC WOL or PHY WOL.
Signed-off-by: Ling Pei Lee <pei.lee.ling@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently assuming that GMAC_AHB_RESET will already be deasserted
by the bootloader. However if this has not been done, probing of the GMAC
will fail. To remedy this we must ensure GMAC_AHB_RESET has been deasserted
prior to probing.
v2 changes:
- remove NULL condition check for stmmac_ahb_rst in stmmac_main.c
- unwrap dev_err() message in stmmac_main.c
- add PTR_ERR() around plat->stmmac_ahb_rst in stmmac_platform.c
v3 changes:
- add error pointer to dev_err() output
- add reset_control_assert(stmmac_ahb_rst) in stmmac_dvr_remove
- revert PTR_ERR() around plat->stmmac_ahb_rst since this is performed
on the returned value of ret by the calling function
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Intel mGbE supports 2.5Gbps link speed by increasing the clock rate by
2.5 times of the original rate. In this mode, the serdes/PHY operates at a
serial baud rate of 3.125 Gbps and the PCS data path and GMII interface of
the MAC operate at 312.5 MHz instead of 125 MHz.
For Intel mGbE, the overclocking of 2.5 times clock rate to support 2.5G is
only able to be configured in the BIOS during boot time. Kernel driver has
no access to modify the clock rate for 1Gbps/2.5G mode. The way to
determined the current 1G/2.5G mode is by reading a dedicated adhoc
register through mdio bus. In short, after the system boot up, it is either
in 1G mode or 2.5G mode which not able to be changed on the fly.
Compared to 1G mode, the 2.5G mode selects the 2500BASEX as PHY interface and
disables the xpcs_an_inband. This is to cater for some PHYs that only
supports 2500BASEX PHY interface with no autonegotiation.
v2: remove MAC supported link speed masking
v3: Restructure to introduce intel_speed_mode_2500() to read serdes registers
for max speed supported and select the appropritate configuration.
Use max_speed to determine the supported link speed mask.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Intel platforms, not all safety features are enabled on the hardware.
The current implementation enable all safety features by default. This
will cause mass error and warning printouts after the module is loaded.
Introduce platform specific safety features flag to enable or disable
each safety features.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link xpcs callback functions for MAC to configure the xpcs EEE feature.
The clk_eee frequency is used to calculate the MULT_FACT_100NS. This is
to adjust the clock tic closer to 100ns.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).
So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Synopsis MAC controller supports auxiliary snapshot feature that
allows user to store a snapshot of the system time based on an external
event.
This patch add supports to the above mentioned feature. Users will be
able to triggered capturing the time snapshot from user-space using
application such as testptp or any other applications that uses the
PTP_EXTTS_REQUEST ioctl request.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For interrupt mode INTM=0, TX/RX transfer complete will trigger signal
not only on sbd_perch_[tx|rx]_intr_o (Transmit/Receive Per Channel) but
also on the sbd_intr_o (Common).
As for multi-MSI implementation, setting interrupt mode INTM=1 is more
efficient as each TX intr and RX intr (TI/RI) will be handled by TX/RX ISR
without the need of calling the common MAC ISR.
Updated the TX/RX NORMAL interrupts status checking process as the
NIS status bit is not asserted for any RI/TI events for INTM=1.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now we introduce MSI interrupt service routines and hook these routines
up if stmmac_open() sees valid irq line being requested:-
stmmac_mac_interrupt() :- MAC (dev->irq), WOL (wol_irq), LPI (lpi_irq)
stmmac_safety_interrupt() :- Safety Feat Correctible Error (sfty_ce_irq)
& Uncorrectible Error (sfty_ue_irq)
stmmac_msi_intr_rx() :- For all RX MSI irq (rx_irq)
stmmac_msi_intr_tx() :- For all TX MSI irq (tx_irq)
Each of IRQs will have its unique name so that we can differentiate
them easily under /proc/interrupts.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to discover whether remote station supports frame preemption,
local station sends verify mPacket and expects response mPacket in
return from the remote station.
So, we add the functions to send and handle event when verify mPacket
and response mPacket are exchanged between the networked stations.
The mechanism to handle different FPE states between local and remote
station (link partner) is implemented using workqueue which starts a
task each time there is some sign of verify & response mPacket exchange
as check in FPE IRQ event. The task retries couple of times to try to
spot the states that both stations are ready to enter FPE ON. This allows
different end points to enable FPE at different time and verify-response
mPacket can happen asynchronously. Ultimately, the task will only turn
FPE ON when local station have both exchange response in both directions.
Thanks to Voon Weifeng for implementing the core functions for detecting
FPE events and send mPacket and phylink related change.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Tan Tee Min <tee.min.tan@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross timestamping is supported on Integrated Ethernet Controller in
Intel SoC such as EHL and TGL with Always Running Timer.
The hardware cross-timestamp result is made available to
applications through the PTP_SYS_OFFSET_PRECISE ioctl which calls
stmmac_getcrosststamp().
Device time is stored in the MAC Auxiliary register. The 64-bit System
time (ART timestamp) is stored in registers that are only addressable
by using MDIO space.
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Intel mGbE variant implemented in EHL and TGL can be set to select
different clock frequency based on GPO bits in MAC_GPIO_STATUS register.
We introduce a new "void (*ptp_clk_freq_config)(void *priv)" in platform
data so that if a platform is required to configure the frequency of clock
source, in this case Intel mGBE does, the platform-specific configuration
of the PTP clock setting is done when stmmac_ptp_register() is called.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch intends to add platform level clocks management. Some
platforms may have their own special clocks, they also need to be
managed dynamically. If you want to manage such clocks, please implement
clks_config callback.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all platform uses DT, so phylink_parse_mode() will skip in-band setup
of pl->supported and pl->link_config.advertising entirely. So, we add the
setting of ovr_an_inband flag to make it works for non-DT platform.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch populates the PCI bus info in the ethtool driver query data.
Users will be able to view PCI bus info using 'ethtool -i <interface>'.
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current IP register MAC_HW_Feature1[ADDR64] only defines
32/40/64 bit width, but some SOCs support others like i.MX8MP
support 34 bits but it maps to 40 bits width in MAC_HW_Feature1[ADDR64].
So overwrite dma_cap.addr64 according to HW real design.
Fixes: 94abdad6974a ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding reference clock (1us tic) for all LPI timer on Intel platforms.
The reference clock is derived from ptp clk. This also enables all LPI
counter.
Signed-off-by: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.
When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
will pass up all rx packets that failed address filtering (similar to
promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
filters and get routed to selected VFFQ Rx queue.
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.
<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+ +----+ +---+ +----------+
| EQoS | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
| MAC | |xPCS| |IF | | PHY |
+----------+ +----+ +---+ +----------+
^ ^ ^ ^
| | | |
+---------------------MDIO-------------------------+
PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
