| Age | Commit message (Collapse) | Author |
|---|
|
Guenter reported boot stalls on a emulated ARM 32-bit platform, which has a
24-bit wide clocksource.
It turns out that the calculated maximal idle time, which limits idle
sleeps to prevent clocksource wrap arounds, is close to the point where the
negative motion detection triggers.
max_idle_ns: 597268854 ns
negative motion tripping point: 671088640 ns
If the idle wakeup is delayed beyond that point, the clocksource
advances far enough to trigger the negative motion detection. This
prevents the clock to advance and in the worst case the system stalls
completely if the consecutive sleeps based on the stale clock are
delayed as well.
Cure this by calculating a more robust cut-off value for negative motion,
which covers 87.5% of the actual clocksource counter width. Compare the
delta against this value to catch negative motion. This is specifically for
clock sources with a small counter width as their wrap around time is close
to the half counter width. For clock sources with wide counters this is not
a problem because the maximum idle time is far from the half counter width
due to the math overflow protection constraints.
For the case at hand this results in a tripping point of 1174405120ns.
Note, that this cannot prevent issues when the delay exceeds the 87.5%
margin, but that's not different from the previous unchecked version which
allowed arbitrary time jumps.
Systems with small counter width are prone to invalid results, but this
problem is unlikely to be seen on real hardware. If such a system
completely stalls for more than half a second, then there are other more
urgent problems than the counter wrapping around.
Fixes: c163e40af9b2 ("timekeeping: Always check for negative motion")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/all/8734j5ul4x.ffs@tglx
Closes: https://lore.kernel.org/all/387b120b-d68a-45e8-b6ab-768cd95d11c2@roeck-us.net
|
|
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c component probing support from Wolfram Sang:
"Add OF component probing.
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular
device can be detected by some firmware provided identifier, other
times that information is not available, and the kernel has to try to
probe each device.
Instead of a delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them
responds. It will then enable the device that responds"
* tag 'i2c-for-6.13-rc1-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: fix typo in I2C OF COMPONENT PROBER
of: base: Document prefix argument for of_get_next_child_with_prefix()
i2c: Fix whitespace style issue
arm64: dts: mediatek: mt8173-elm-hana: Mark touchscreens and trackpads as fail
platform/chrome: Introduce device tree hardware prober
i2c: of-prober: Add GPIO support to simple helpers
i2c: of-prober: Add simple helpers for regulator support
i2c: Introduce OF component probe function
of: base: Add for_each_child_of_node_with_prefix()
of: dynamic: Add of_changeset_update_prop_string
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull bprintf() removal from Steven Rostedt:
- Remove unused bprintf() function, that was added with the rest of the
"bin-printf" functions.
These are functions that are used by trace_printk() that allows to
quickly save the format and arguments into the ring buffer without
the expensive processing of converting numbers to ASCII. Then on
output, at a much later time, the ring buffer is read and the string
processing occurs then. The bprintf() was added for consistency but
was never used. It can be safely removed.
* tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
printf: Remove unused 'bprintf'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Borislav Petkov:
- Fix a case where posix timers with a thread-group-wide target would
miss signals if some of the group's threads are exiting
- Fix a hang caused by ndelay() calling the wrong delay function
__udelay()
- Fix a wrong offset calculation in adjtimex(2) when using ADJ_MICRO
(microsecond resolution) and a negative offset
* tag 'timers_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Target group sigqueue to current task only if not exiting
delay: Fix ndelay() spuriously treated as udelay()
ntp: Remove invalid cast in time offset math
|
|
bprintf() is unused. Remove it. It was added in the commit 4370aa4aa753
("vsprintf: add binary printf") but as far as I can see was never used,
unlike the other two functions in that patch.
Link: https://lore.kernel.org/20241002173147.210107-1-linux@treblig.org
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Pull more block updates from Jens Axboe:
- NVMe pull request via Keith:
- Use correct srcu list traversal (Breno)
- Scatter-gather support for metadata (Keith)
- Fabrics shutdown race condition fix (Nilay)
- Persistent reservations updates (Guixin)
- Add the required bits for MD atomic write support for raid0/1/10
- Correct return value for unknown opcode in ublk
- Fix deadlock with zone revalidation
- Fix for the io priority request vs bio cleanups
- Use the correct unsigned int type for various limit helpers
- Fix for a race in loop
- Cleanup blk_rq_prep_clone() to prevent uninit-value warning and make
it easier for actual humans to read
- Fix potential UAF when iterating tags
- A few fixes for bfq-iosched UAF issues
- Fix for brd discard not decrementing the allocated page count
- Various little fixes and cleanups
* tag 'block-6.13-20242901' of git://git.kernel.dk/linux: (36 commits)
brd: decrease the number of allocated pages which discarded
block, bfq: fix bfqq uaf in bfq_limit_depth()
block: Don't allow an atomic write be truncated in blkdev_write_iter()
mq-deadline: don't call req_get_ioprio from the I/O completion handler
block: Prevent potential deadlock in blk_revalidate_disk_zones()
block: Remove extra part pointer NULLify in blk_rq_init()
nvme: tuning pr code by using defined structs and macros
nvme: introduce change ptpl and iekey definition
block: return bool from get_disk_ro and bdev_read_only
block: remove a duplicate definition for bdev_read_only
block: return bool from blk_rq_aligned
block: return unsigned int from blk_lim_dma_alignment_and_pad
block: return unsigned int from queue_dma_alignment
block: return unsigned int from bdev_io_opt
block: req->bio is always set in the merge code
block: don't bother checking the data direction for merges
block: blk-mq: fix uninit-value in blk_rq_prep_clone and refactor
Revert "block, bfq: merge bfq_release_process_ref() into bfq_put_cooperator()"
md/raid10: Atomic write support
md/raid1: Atomic write support
...
|
|
Pull more io_uring updates from Jens Axboe:
- Remove a leftover struct from when the cqwait registered waiting was
transitioned to regions.
- Fix for an issue introduced in this merge window, where nop->fd might
be used uninitialized. Ensure it's always set.
- Add capping of the task_work run in local task_work mode, to prevent
bursty and long chains from adding too much latency.
- Work around xa_store() leaving ->head non-NULL if it encounters an
allocation error during storing. Just a debug trigger, and can go
away once xa_store() behaves in a more expected way for this
condition. Not a major thing as it basically requires fault injection
to trigger it.
- Fix a few mapping corner cases
- Fix KCSAN complaint on reading the table size post unlock. Again not
a "real" issue, but it's easy to silence by just keeping the reading
inside the lock that protects it.
* tag 'io_uring-6.13-20242901' of git://git.kernel.dk/linux:
io_uring/tctx: work around xa_store() allocation error issue
io_uring: fix corner case forgetting to vunmap
io_uring: fix task_work cap overshooting
io_uring: check for overflows in io_pin_pages
io_uring/nop: ensure nop->fd is always initialized
io_uring: limit local tw done
io_uring: add io_local_work_pending()
io_uring/region: return negative -E2BIG in io_create_region()
io_uring: protect register tracing
io_uring: remove io_uring_cqwait_reg_arg
|
|
Pull more kvm updates from Paolo Bonzini:
- ARM fixes
- RISC-V Svade and Svadu (accessed and dirty bit) extension support for
host and guest
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: riscv: selftests: Add Svade and Svadu Extension to get-reg-list test
RISC-V: KVM: Add Svade and Svadu Extensions Support for Guest/VM
dt-bindings: riscv: Add Svade and Svadu Entries
RISC-V: Add Svade and Svadu Extensions Support
KVM: arm64: Use MDCR_EL2.HPME to evaluate overflow of hyp counters
KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
KVM: arm64: Mark set_sysreg_masks() as inline to avoid build failure
KVM: arm64: vgic-its: Add stronger type-checking to the ITS entry sizes
KVM: arm64: vgic: Kill VGIC_MAX_PRIVATE definition
KVM: arm64: vgic: Make vgic_get_irq() more robust
KVM: arm64: vgic-v3: Sanitise guest writes to GICR_INVLPIR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add generic support for built-in boot DTB files
- Enable TAB cycling for dialog buttons in nconfig
- Fix issues in streamline_config.pl
- Refactor Kconfig
- Add support for Clang's AutoFDO (Automatic Feedback-Directed
Optimization)
- Add support for Clang's Propeller, a profile-guided optimization.
- Change the working directory to the external module directory for M=
builds
- Support building external modules in a separate output directory
- Enable objtool for *.mod.o and additional kernel objects
- Use lz4 instead of deprecated lz4c
- Work around a performance issue with "git describe"
- Refactor modpost
* tag 'kbuild-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (85 commits)
kbuild: rename .tmp_vmlinux.kallsyms0.syms to .tmp_vmlinux0.syms
gitignore: Don't ignore 'tags' directory
kbuild: add dependency from vmlinux to resolve_btfids
modpost: replace tdb_hash() with hash_str()
kbuild: deb-pkg: add python3:native to build dependency
genksyms: reduce indentation in export_symbol()
modpost: improve error messages in device_id_check()
modpost: rename alias symbol for MODULE_DEVICE_TABLE()
modpost: rename variables in handle_moddevtable()
modpost: move strstarts() to modpost.h
modpost: convert do_usb_table() to a generic handler
modpost: convert do_of_table() to a generic handler
modpost: convert do_pnp_device_entry() to a generic handler
modpost: convert do_pnp_card_entries() to a generic handler
modpost: call module_alias_printf() from all do_*_entry() functions
modpost: pass (struct module *) to do_*_entry() functions
modpost: remove DEF_FIELD_ADDR_VAR() macro
modpost: deduplicate MODULE_ALIAS() for all drivers
modpost: introduce module_alias_printf() helper
modpost: remove unnecessary check in do_acpi_entry()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"New drivers:
- Amlogic A4 and A5 RTC
- Marvell 88PM886 PMIC RTC
- Renesas RTCA-3 for Renesas RZ/G3S
Driver updates:
- ab-eoz9: fix temperature and alarm support
- cmos: improve locking behaviour
- isl12022: add alarm support
- m48t59: improve epoch handling
- mt6359: add range
- rzn1: fix BCD conversions and simplify driver"
* tag 'rtc-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (38 commits)
rtc: ab-eoz9: don't fail temperature reads on undervoltage notification
rtc: rzn1: reduce register access
rtc: rzn1: drop superfluous wday calculation
m68k: mvme147, mvme16x: Adopt rtc-m48t59 platform driver
rtc: brcmstb-waketimer: don't include 'pm_wakeup.h' directly
rtc: m48t59: Use platform_data struct for year offset value
rtc: ab-eoz9: fix abeoz9_rtc_read_alarm
rtc: rv3028: fix RV3028_TS_COUNT type
rtc: rzn1: update Michel's email
rtc: rzn1: fix BCD to rtc_time conversion errors
rtc: amlogic-a4: fix compile error
rtc: amlogic-a4: drop error messages
MAINTAINERS: Add an entry for Amlogic RTC driver
rtc: support for the Amlogic on-chip RTC
dt-bindings: rtc: Add Amlogic A4 and A5 RTC
rtc: add driver for Marvell 88PM886 PMIC RTC
rtc: check if __rtc_read_time was successful in rtc_timer_do_work()
rtc: pcf8563: Switch to regmap
rtc: pcf8563: Sort headers alphabetically
rtc: abx80x: Fix WDT bit position of the status register
...
|
|
Pull ceph updates from Ilya Dryomov:
"A fix for the mount "device" string parser from Patrick and two cred
reference counting fixups from Max, marked for stable.
Also included a number of cleanups and a tweak to MAINTAINERS to avoid
unnecessarily CCing netdev list"
* tag 'ceph-for-6.13-rc1' of https://github.com/ceph/ceph-client:
ceph: fix cred leak in ceph_mds_check_access()
ceph: pass cred pointer to ceph_mds_auth_match()
ceph: improve caps debugging output
ceph: correct ceph_mds_cap_peer field name
ceph: correct ceph_mds_cap_item field name
ceph: miscellaneous spelling fixes
ceph: Use strscpy() instead of strcpy() in __get_snap_name()
ceph: Use str_true_false() helper in status_show()
ceph: requalify some char pointers as const
ceph: extract entity name from device id
MAINTAINERS: exclude net/ceph from networking
ceph: Remove fs/ceph deadcode
libceph: Remove unused ceph_crypto_key_encode
libceph: Remove unused ceph_osdc_watch_check
libceph: Remove unused pagevec functions
libceph: Remove unused ceph_pagelist functions
|
|
Pull NFS client updates from Trond Myklebust:
"Bugfixes:
- nfs/localio: fix for a memory corruption in nfs_local_read_done
- Revert "nfs: don't reuse partially completed requests in
nfs_lock_and_join_requests"
- nfsv4:
- ignore SB_RDONLY when mounting nfs
- Fix a use-after-free problem in open()
- sunrpc:
- clear XPRT_SOCK_UPD_TIMEOUT when reseting the transport
- timeout and cancel TLS handshake with -ETIMEDOUT
- fix one UAF issue caused by sunrpc kernel tcp socket
- Fix a hang in TLS sock_close if sk_write_pending
- pNFS/blocklayout: Fix device registration issues
Features and cleanups:
- localio cleanups from Mike Snitzer
- Clean up refcounting on the nfs version modules
- __counted_by() annotations
- nfs: make processes that are waiting for an I/O lock killable"
* tag 'nfs-for-6.13-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (24 commits)
fs/nfs/io: make nfs_start_io_*() killable
nfs/blocklayout: Limit repeat device registration on failure
nfs/blocklayout: Don't attempt unregister for invalid block device
sunrpc: fix one UAF issue caused by sunrpc kernel tcp socket
SUNRPC: timeout and cancel TLS handshake with -ETIMEDOUT
sunrpc: clear XPRT_SOCK_UPD_TIMEOUT when reset transport
nfs: ignore SB_RDONLY when mounting nfs
Revert "nfs: don't reuse partially completed requests in nfs_lock_and_join_requests"
Revert "fs: nfs: fix missing refcnt by replacing folio_set_private by folio_attach_private"
nfs/localio: must clear res.replen in nfs_local_read_done
NFSv4.0: Fix a use-after-free problem in the asynchronous open()
NFSv4.0: Fix the wake up of the next waiter in nfs_release_seqid()
SUNRPC: Fix a hang in TLS sock_close if sk_write_pending
sunrpc: remove newlines from tracepoints
nfs: Annotate struct pnfs_commit_array with __counted_by()
nfs/localio: eliminate need for nfs_local_fsync_work forward declaration
nfs/localio: remove extra indirect nfs_to call to check {read,write}_iter
nfs/localio: eliminate unnecessary kref in nfs_local_fsync_ctx
nfs/localio: remove redundant suid/sgid handling
NFS: Implement get_nfs_version()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.13-rc1.
Nothing major at all this time, only some small changes:
- few device tree binding updates
- 8250_exar serial driver updates
- imx serial driver updates
- sprd_serial driver updates
- other tiny serial driver updates, full details in the shortlog
All of these have been in linux-next for a while with one reported
issue, but that commit has now been reverted"
* tag 'tty-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (37 commits)
Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"
serial: amba-pl011: fix build regression
dt-bindings: serial: Add a new compatible string for ums9632
serial: sprd: Add support for sc9632
tty/serial/altera_uart: unwrap error log string
tty/serial/altera_jtaguart: unwrap error log string
serial: amba-pl011: Fix RX stall when DMA is used
tty: ldsic: fix tty_ldisc_autoload sysctl's proc_handler
serial: 8250_fintek: Add support for F81216E
serial: sh-sci: Clean sci_ports[0] after at earlycon exit
tty: atmel_serial: Fix typo retreives to retrieves
tty: atmel_serial: Use devm_platform_ioremap_resource()
serial: 8250: omap: Move pm_runtime_get_sync
tty: serial: samsung: Add Exynos8895 compatible
dt-bindings: serial: samsung: Add samsung,exynos8895-uart compatible
serial: 8250_dw: Add Sophgo SG2044 quirk
dt-bindings: serial: snps-dw-apb-uart: Add Sophgo SG2044 uarts
dt-bindings: serial: snps,dw-apb-uart: merge duplicate compatible entry.
altera_jtaguart: Use dev_err() to report error attaching IRQ
altera_uart: Use dev_err() to report error attaching IRQ handler
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes. Majority of changes are device-specific
fixes and quirks, while there are a few core fixes to address
regressions and corner cases spotted by fuzzers.
- Fix of spinlock range that wrongly covered kvfree() call in rawmidi
- Fix potential NULL dereference at PCM mmap
- Fix incorrectly advertised MIDI 2.0 UMP Function Block info
- Various ASoC AMD quirks and fixes
- ASoC SOF Intel, Mediatek, HDMI-codec fixes
- A few more quirks and TAS2781 codec fix for HD-audio
- A couple of fixes for USB-audio for malicious USB descriptors"
* tag 'sound-fix-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: hda: improve bass speaker support for ASUS Zenbook UM5606WA
ALSA: hda/realtek: Apply quirk for Medion E15433
ASoC: amd: yc: Add a quirk for microfone on Lenovo ThinkPad P14s Gen 5 21MES00B00
ASoC: SOF: ipc3-topology: Convert the topology pin index to ALH dai index
ASoC: mediatek: Check num_codecs is not zero to avoid panic during probe
ASoC: amd: yc: Fix for enabling DMIC on acp6x via _DSD entry
ALSA: ump: Fix evaluation of MIDI 1.0 FB info
ALSA: core: Fix possible NULL dereference caused by kunit_kzalloc()
ALSA: hda: Show the codec quirk info at probing
ALSA: asihpi: Remove unused variable
ALSA: hda/realtek: Set PCBeep to default value for ALC274
ALSA: hda/tas2781: Add speaker id check for ASUS projects
ALSA: hda/realtek: Update ALC225 depop procedure
ALSA: hda/realtek: Enable speaker pins for Medion E15443 platform
ALSA: hda/realtek: fix mute/micmute LEDs don't work for EliteBook X G1i
ALSA: usb-audio: Fix out of bounds reads when finding clock sources
ALSA: rawmidi: Fix kvfree() call in spinlock
ALSA: hda/realtek: Fix Internal Speaker and Mic boost of Infinix Y4 Max
ASoC: amd: yc: Add quirk for microphone on Lenovo Thinkpad T14s Gen 6 21M1CTO1WW
ASoC: doc: dapm: Add location information for dapm-graph tool
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc/IIO/whatever driver subsystem updates from Greg KH:
"Here is the 'big and hairy' char/misc/iio and other small driver
subsystem updates for 6.13-rc1.
Loads of things in here, and even a fun merge conflict!
- rust misc driver bindings and other rust changes to make misc
drivers actually possible.
I think this is the tipping point, expect to see way more rust
drivers going forward now that these bindings are present. Next
merge window hopefully we will have pci and platform drivers
working, which will fully enable almost all driver subsystems to
start accepting (or at least getting) rust drivers.
This is the end result of a lot of work from a lot of people,
congrats to all of them for getting this far, you've proved many of
us wrong in the best way possible, working code :)
- IIO driver updates, too many to list individually, that subsystem
keeps growing and growing...
- Interconnect driver updates
- nvmem driver updates
- pwm driver updates
- platform_driver::remove() fixups, loads of them
- counter driver updates
- misc driver updates (keba?)
- binder driver updates and fixes
- loads of other small char/misc/etc driver updates and additions,
full details in the shortlog.
All of these have been in linux-next for a while, with no other
reported issues other than that merge conflict"
* tag 'char-misc-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (401 commits)
mei: vsc: Fix typo "maintstepping" -> "mainstepping"
firmware: Switch back to struct platform_driver::remove()
misc: isl29020: Fix the wrong format specifier
scripts/tags.sh: Don't tag usages of DEFINE_MUTEX
fpga: Switch back to struct platform_driver::remove()
mei: vsc: Improve error logging in vsc_identify_silicon()
mei: vsc: Do not re-enable interrupt from vsc_tp_reset()
dt-bindings: spmi: qcom,x1e80100-spmi-pmic-arb: Add SAR2130P compatible
dt-bindings: spmi: spmi-mtk-pmif: Add compatible for MT8188
spmi: pmic-arb: fix return path in for_each_available_child_of_node()
iio: Move __private marking before struct element priv in struct iio_dev
docs: iio: ad7380: add adaq4370-4 and adaq4380-4
iio: adc: ad7380: add support for adaq4370-4 and adaq4380-4
iio: adc: ad7380: use local dev variable to shorten long lines
iio: adc: ad7380: fix oversampling formula
dt-bindings: iio: adc: ad7380: add adaq4370-4 and adaq4380-4 compatible parts
bus: mhi: host: pci_generic: Use pcim_iomap_region() to request and map MHI BAR
bus: mhi: host: Switch trace_mhi_gen_tre fields to native endian
misc: atmel-ssc: Use of_property_present() for non-boolean properties
misc: keba: Add hardware dependency
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work
going into the debugfs interface for the thunderbolt (i.e. USB4) code,
to help with debugging the myrad ways that hardware vendors get their
interfaces messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: typec: tcpm: Add support for sink-bc12-completion-time-ms DT property
dt-bindings: usb: maxim,max33359: add usage of sink bc12 time property
dt-bindings: connector: Add time property for Sink BC12 detection completion
usb: dwc3: gadget: Remove dwc3_request->needs_extra_trb
usb: dwc3: gadget: Cleanup SG handling
usb: dwc3: gadget: Fix looping of queued SG entries
usb: dwc3: gadget: Fix checking for number of TRBs left
usb: dwc3: ep0: Don't clear ep0 DWC3_EP_TRANSFER_STARTED
Revert "usb: gadget: composite: fix OS descriptors w_value logic"
usb: ehci-spear: fix call balance of sehci clk handling routines
USB: make to_usb_device_driver() use container_of_const()
USB: make to_usb_driver() use container_of_const()
USB: properly lock dynamic id list when showing an id
USB: make single lock for all usb dynamic id lists
drivers/usb/storage: refactor min with min_t
drivers/usb/serial: refactor min with min_t
drivers/usb/musb: refactor min/max with min_t/max_t
drivers/usb/mon: refactor min with min_t
drivers/usb/misc: refactor min with min_t
drivers/usb/host: refactor min/max with min_t/max_t
...
|
|
Pull ARM updates from Russell King:
- add dev_is_amba() function to allow conversions during the next cycle
- improve PREEMPT_RT performance with VFP
- KASAN fixes for vmap stack
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux:
ARM: 9431/1: mm: Pair atomic_set_release() with _read_acquire()
ARM: 9430/1: entry: Do a dummy read from VMAP shadow
ARM: 9429/1: ioremap: Sync PGDs for VMALLOC shadow
ARM: 9426/1: vfp: Move sending signals outside of vfp_state_hold()ed section.
ARM: 9425/1: vfp: Use vfp_state_hold() in vfp_support_entry().
ARM: 9424/1: vfp: Use vfp_state_hold() in vfp_sync_hwstate().
ARM: 9423/1: vfp: Provide vfp_state_hold() for VFP locking.
ARM: 9415/1: amba: Add dev_is_amba() function and export it for modules
|
|
A recent rework on delay functions wrongly ended up calling __udelay()
instead of __ndelay() for nanosecond delays, increasing those by 1000.
As a result hangs have been observed on boot
Restore the right function calls.
Fixes: 19e2d91d8cb1 ("delay: Rework udelay and ndelay")
Reported-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/all/20241121152931.51884-1-frederic@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull more tracing updates from Steven Rostedt:
- Add trace flag for NEED_RESCHED_LAZY
Now that NEED_RESCHED_LAZY is upstream, add it to the status bits of
the common_flags. This will now show when the NEED_RESCHED_LAZY flag
is set that is used for debugging latency issues in the kernel via a
trace.
- Remove leftover "__idx" variable when SRCU was removed from the
tracepoint code
- Add rcu_tasks_trace guard
To add a guard() around the tracepoint code, a rcu_tasks_trace guard
needs to be created first.
- Remove __DO_TRACE() macro and just call __DO_TRACE_CALL() directly
The DO_TRACE() macro has conditional locking depending on what was
passed into the macro parameters. As the guts of the macro has been
moved to __DO_TRACE_CALL() to handle static call logic, there's no
reason to keep the __DO_TRACE() macro around.
It is better to just do the locking in place without the conditionals
and call __DO_TRACE_CALL() from those locations. The "cond" passed in
can also be moved out of that macro. This simplifies the code.
- Remove the "cond" from the system call tracepoint macros
The "cond" variable was added to allow some tracepoints to check a
condition within the static_branch (jump/nop) logic. The system calls
do not need this. Removing it simplifies the code.
- Replace scoped_guard() with just guard() in the tracepoint logic
guard() works just as well as scoped_guard() in the tracepoint logic
and the scoped_guard() causes some issues.
* tag 'trace-v6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Use guard() rather than scoped_guard()
tracing: Remove cond argument from __DECLARE_TRACE_SYSCALL
tracing: Remove conditional locking from __DO_TRACE()
rcupdate_trace: Define rcu_tasks_trace lock guard
tracing: Remove __idx variable from __DO_TRACE
tracing: Move it_func[0] comment to the relevant context
tracing: Record task flag NEED_RESCHED_LAZY.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bluetooth.
Current release - regressions:
- rtnetlink: fix rtnl_dump_ifinfo() error path
- bluetooth: remove the redundant sco_conn_put
Previous releases - regressions:
- netlink: fix false positive warning in extack during dumps
- sched: sch_fq: don't follow the fast path if Tx is behind now
- ipv6: delete temporary address if mngtmpaddr is removed or
unmanaged
- tcp: fix use-after-free of nreq in reqsk_timer_handler().
- bluetooth: fix slab-use-after-free Read in set_powered_sync
- l2tp: fix warning in l2tp_exit_net found
- eth:
- bnxt_en: fix receive ring space parameters when XDP is active
- lan78xx: fix double free issue with interrupt buffer allocation
- tg3: set coherent DMA mask bits to 31 for BCM57766 chipsets
Previous releases - always broken:
- ipmr: fix tables suspicious RCU usage
- iucv: MSG_PEEK causes memory leak in iucv_sock_destruct()
- eth:
- octeontx2-af: fix low network performance
- stmmac: dwmac-socfpga: set RX watchdog interrupt as broken
- rtase: correct the speed for RTL907XD-V1
Misc:
- some documentation fixup"
* tag 'net-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (49 commits)
ipmr: fix build with clang and DEBUG_NET disabled.
Documentation: tls_offload: fix typos and grammar
Fix spelling mistake
ipmr: fix tables suspicious RCU usage
ip6mr: fix tables suspicious RCU usage
ipmr: add debug check for mr table cleanup
selftests: rds: move test.py to TEST_FILES
net_sched: sch_fq: don't follow the fast path if Tx is behind now
tcp: Fix use-after-free of nreq in reqsk_timer_handler().
net: phy: fix phy_ethtool_set_eee() incorrectly enabling LPI
net: Comment copy_from_sockptr() explaining its behaviour
rxrpc: Improve setsockopt() handling of malformed user input
llc: Improve setsockopt() handling of malformed user input
Bluetooth: SCO: remove the redundant sco_conn_put
Bluetooth: MGMT: Fix possible deadlocks
Bluetooth: MGMT: Fix slab-use-after-free Read in set_powered_sync
bnxt_en: Unregister PTP during PCI shutdown and suspend
bnxt_en: Refactor bnxt_ptp_init()
bnxt_en: Fix receive ring space parameters when XDP is active
bnxt_en: Fix queue start to update vnic RSS table
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- replace power_supply_register_no_ws() with power_supply_register()
and a new "no_wakeup_source" field in struct power_supply_config
- constify battery info tables in the core and all drivers
- switch back to remove callback for all platform drivers
- allow power_supply_put() to be called from atomic context
- mark attribute arrays read-only after init
Power-supply drivers:
- new driver for TWL6030 and TWL6032
- rk817: improve battery capacity calibration
- misc small cleanups and fixes"
* tag 'for-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (42 commits)
power: reset: ep93xx: add AUXILIARY_BUS dependency
dt-bindings: power: reset: Convert mode-.* properties to array
power: supply: sc27xx: Fix battery detect GPIO probe
dt-bindings: power: supply: sc27xx-fg: document deprecated bat-detect-gpio
reset: keystone-reset: remove unused macros
power: supply: axp20x_battery: Use scaled iio_read_channel
power: supply: axp20x_usb_power: Use scaled iio_read_channel
power: supply: generic-adc-battery: change my gmail
power: supply: pmu_battery: Set power supply type to BATTERY
power: Switch back to struct platform_driver::remove()
power: supply: hwmon: move interface to private header
power: supply: rk817: Update battery capacity calibration
power: supply: rk817: stop updating info in suspend
power: supply: rt9471: Use IC status regfield to report real charger status
power: supply: rt9471: Fix wrong WDT function regfield declaration
dt-bindings: power/supply: qcom,pmi8998-charger: Drop incorrect "#interrupt-cells" from example
power: supply: core: mark attribute arrays as ro_after_init
power: supply: core: unexport power_supply_property_is_writeable()
power: supply: core: use device mutex wrappers
power: supply: bq27xxx: Fix registers of bq27426
...
|
|
When phy_ethtool_set_eee_noneg() detects a change in the LPI
parameters, it attempts to update phylib state and trigger the link
to cycle so the MAC sees the updated parameters.
However, in doing so, it sets phydev->enable_tx_lpi depending on
whether the EEE configuration allows the MAC to generate LPI without
taking into account the result of negotiation.
This can be demonstrated with a 1000base-T FD interface by:
# ethtool --set-eee eno0 advertise 8 # cause EEE to be not negotiated
# ethtool --set-eee eno0 tx-lpi off
# ethtool --set-eee eno0 tx-lpi on
This results in being true, despite EEE not having been negotiated and:
# ethtool --show-eee eno0
EEE status: enabled - inactive
Tx LPI: 250 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Fix this by keeping track of whether EEE was negotiated via a new
eee_active member in struct phy_device, and include this state in
the decision whether phydev->enable_tx_lpi should be set.
Fixes: 3e43b903da04 ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tErSe-005RhB-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
copy_from_sockptr() has a history of misuse. Add a comment explaining that
the function follows API of copy_from_user(), i.e. returns 0 for success,
or number of bytes not copied on error.
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This commit renames the alias symbol, __mod_<type>__<name>_device_table
to __mod_device_table__<type>__<name>.
This change simplifies the code slightly, as there is no longer a need
to check both the prefix and suffix.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add a common init function for arch-specific ACPI
initialization, clean up idle states initialization in the ACPI
processor_idle driver and update quirks:
- Introduce acpi_arch_init() for architecture-specific ACPI subsystem
initialization (Miao Wang)
- Clean up Asus quirks in acpi_quirk_skip_dmi_ids[] and add a quirk
to skip I2C clients on Acer Iconia One 8 A1-840 (Hans de Goede)
- Make the ACPI processor_idle driver use acpi_idle_play_dead() for
all idle states regardless of their types (Rafael Wysocki)"
* tag 'acpi-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: introduce acpi_arch_init()
ACPI: x86: Clean up Asus entries in acpi_quirk_skip_dmi_ids[]
ACPI: x86: Add skip i2c clients quirk for Acer Iconia One 8 A1-840
ACPI: processor_idle: Use acpi_idle_play_dead() for all C-states
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd
Pull more iommufd updates from Jason Gunthorpe:
"Change the driver callback op domain_alloc_user() into two ops:
domain_alloc_paging_flags() and domain_alloc_nesting() that better
describe what the ops are expected to do.
There will be per-driver cleanup based on this going into the next
cycle via the driver trees"
* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
iommu: Rename ops->domain_alloc_user() to domain_alloc_paging_flags()
iommu: Add ops->domain_alloc_nested()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
- structure optimization of few bus structures and header updates
- support for 2.0 disco spec
- amd driver updates for acp revision, refactoring code and support for
acp6.3
- soft reset support for cadence driver
* tag 'soundwire-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (24 commits)
soundwire: Minor formatting fixups in sdw.h header
soundwire: Update the includes on the sdw.h header
soundwire: cadence: clear MCP BLOCK_WAKEUP in init
soundwire: cadence: add soft-reset on startup
soundwire: intel_auxdevice: add kernel parameter for mclk divider
soundwire: mipi-disco: add support for DP0/DPn 'lane-list' property
soundwire: mipi-disco: add new properties from 2.0 spec
soundwire: mipi-disco: add comment on DP0-supported property
soundwire: mipi-disco: add support for peripheral channelprepare timeout
soundwire: mipi_disco: add support for clock-scales property
soundwire: mipi-disco: add error handling for property array read
soundwire: mipi-disco: remove DPn audio-modes
soundwire: optimize sdw_dpn_prop
soundwire: optimize sdw_dp0_prop
soundwire: optimize sdw_slave_prop
soundwire: optimize sdw_bus structure
soundwire: optimize sdw_master_prop
soundwire: optimize sdw_stream_runtime memory layout
soundwire: mipi_disco: add MIPI-specific property_read_bool() helpers
soundwire: Correct some typos in comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hardware support:
- ST STM32MP25 combophy support
- Sparx5 support for lan969x serdes and updates to driver to support
this
- NXP PTN3222 eUSB2 to USB2 redriver
- Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2
support, X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP
UFS PHY support and SA8775P eDP PHY support
- Rockchip rk3576 usbdp and rk3576 usb2 phy support
- Binding for Microchip ATA6561 can phy
Updates:
- Freescale driver updates from hdmi support
- Conversion of rockchip rk3228 hdmi phy binding to yaml
- Broadcom usb2-phy deprecated support dropped and USB init array
update for BCM4908
- TI USXGMII mode support in J7200
- Switch back to platform_driver::remove() subsystem update"
* tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (59 commits)
phy: qcom: qmp: Fix lecacy-legacy typo
phy: lan969x-serdes: add support for lan969x serdes driver
dt-bindings: phy: sparx5: document lan969x
phy: sparx5-serdes: add support for branching on chip type
phy: sparx5-serdes: add indirection layer to register macros
phy: sparx5-serdes: add function for getting the CMU index
phy: sparx5-serdes: add ops to match data
phy: sparx5-serdes: add constant for the number of CMU's
phy: sparx5-serdes: add constants to match data
phy: sparx5-serdes: add support for private match data
phy: bcm-ns-usb2: drop support for old binding variant
dt-bindings: phy: bcm-ns-usb2-phy: drop deprecated variant
dt-bindings: phy: Add QMP UFS PHY compatible for QCS8300
dt-bindings: phy: qcom: snps-eusb2: Add SAR2130P compatible
dt-bindings: phy: ti,tcan104x-can: Document Microchip ATA6561
phy: airoha: Fix REG_CSR_2L_RX{0,1}_REV0 definitions
phy: airoha: Fix REG_CSR_2L_JCPLL_SDM_HREN config in airoha_pcie_phy_init_ssc_jcpll()
phy: airoha: Fix REG_PCIE_PMA_TX_RESET config in airoha_pcie_phy_init_csr_2l()
phy: airoha: Fix REG_CSR_2L_PLL_CMN_RESERVE0 config in airoha_pcie_phy_init_clk_out()
phy: phy-rockchip-samsung-hdptx: Don't request RST_PHY/RST_ROPLL/RST_LCPLL
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New hardware support:
- Qualcomm SAR2130P GPI dma support
- Sifive PIC64GX pdma support
- Rcar r7s72100 support and associated updates
Updates:
- STM32 DMA3 updates for packing/unpacking mode and prevention of
additional xfers
- Simplification of devm_acpi_dma_controller_register() and associate
cleanup including headers
- loongson prefix renames
- Switch back to platform_driver::remove() subsystem update"
* tag 'dmaengine-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: loongson2-apb: Rename the prefix ls2x to loongson2
dt-bindings: dma: sifive pdma: Add PIC64GX to compatibles
dmaengine: fix typo in the comment
dmaengine: stm32-dma3: clamp AXI burst using match data
dmaengine: stm32-dma3: prevent LL refactoring thanks to DT configuration
dt-bindings: dma: stm32-dma3: prevent additional transfers
dmaengine: stm32-dma3: refactor HW linked-list to optimize memory accesses
dmaengine: stm32-dma3: prevent pack/unpack thanks to DT configuration
dt-bindings: dma: stm32-dma3: prevent packing/unpacking mode
dmaengine: idxd: Move DSA/IAA device IDs to IDXD driver
dt-bindings: dma: qcom,gpi: Add SAR2130P compatible
dmaengine: Switch back to struct platform_driver::remove()
dmaengine: ep93xx: Fix unsigned compared against 0
dmaengine: acpi: Clean up headers
dmaengine: acpi: Simplify devm_acpi_dma_controller_register()
dmaengine: acpi: Drop unused devm_acpi_dma_controller_free()
dmaengine: sh: rz-dmac: add r7s72100 support
dt-bindings: dma: rz-dmac: Document RZ/A1H SoC
|
|
Pull VFIO updates from Alex Williamson:
- Constify an unmodified structure used in linking vfio and kvm
(Christophe JAILLET)
- Add ID for an additional hardware SKU supported by the nvgrace-gpu
vfio-pci variant driver (Ankit Agrawal)
- Fix incorrect signed cast in QAT vfio-pci variant driver, negating
test in check_add_overflow(), though still caught by later tests
(Giovanni Cabiddu)
- Additional debugfs attributes exposed in hisi_acc vfio-pci variant
driver for migration debugging (Longfang Liu)
- Migration support is added to the virtio vfio-pci variant driver,
becoming the primary feature of the driver while retaining emulation
of virtio legacy support as a secondary option (Yishai Hadas)
- Fixes to a few unwind flows in the mlx5 vfio-pci driver discovered
through reviews of the virtio variant driver (Yishai Hadas)
- Fix an unlikely issue where a PCI device exposed to userspace with an
unknown capability at the base of the extended capability chain can
overflow an array index (Avihai Horon)
* tag 'vfio-v6.13-rc1' of https://github.com/awilliam/linux-vfio:
vfio/pci: Properly hide first-in-list PCIe extended capability
vfio/mlx5: Fix unwind flows in mlx5vf_pci_save/resume_device_data()
vfio/mlx5: Fix an unwind issue in mlx5vf_add_migration_pages()
vfio/virtio: Enable live migration once VIRTIO_PCI was configured
vfio/virtio: Add PRE_COPY support for live migration
vfio/virtio: Add support for the basic live migration functionality
virtio-pci: Introduce APIs to execute device parts admin commands
virtio: Manage device and driver capabilities via the admin commands
virtio: Extend the admin command to include the result size
virtio_pci: Introduce device parts access commands
Documentation: add debugfs description for hisi migration
hisi_acc_vfio_pci: register debugfs for hisilicon migration driver
hisi_acc_vfio_pci: create subfunction for data reading
hisi_acc_vfio_pci: extract public functions for container_of
vfio/qat: fix overflow check in qat_vf_resume_write()
vfio/nvgrace-gpu: Add a new GH200 SKU to the devid table
kvm/vfio: Constify struct kvm_device_ops
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-v updates from Palmer Dabbelt:
- Support for pointer masking in userspace
- Support for probing vector misaligned access performance
- Support for qspinlock on systems with Zacas and Zabha
* tag 'riscv-for-linus-6.13-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (38 commits)
RISC-V: Remove unnecessary include from compat.h
riscv: Fix default misaligned access trap
riscv: Add qspinlock support
dt-bindings: riscv: Add Ziccrse ISA extension description
riscv: Add ISA extension parsing for Ziccrse
asm-generic: ticket-lock: Add separate ticket-lock.h
asm-generic: ticket-lock: Reuse arch_spinlock_t of qspinlock
riscv: Implement xchg8/16() using Zabha
riscv: Implement arch_cmpxchg128() using Zacas
riscv: Improve zacas fully-ordered cmpxchg()
riscv: Implement cmpxchg8/16() using Zabha
dt-bindings: riscv: Add Zabha ISA extension description
riscv: Implement cmpxchg32/64() using Zacas
riscv: Do not fail to build on byte/halfword operations with Zawrs
riscv: Move cpufeature.h macros into their own header
KVM: riscv: selftests: Add Smnpm and Ssnpm to get-reg-list test
RISC-V: KVM: Allow Smnpm and Ssnpm extensions for guests
riscv: hwprobe: Export the Supm ISA extension
riscv: selftests: Add a pointer masking test
riscv: Allow ptrace control of the tagged address ABI
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into HEAD
RISC-V Paches for the 6.13 Merge Window, Part 1
* Support for pointer masking in userspace,
* Support for probing vector misaligned access performance.
* Support for qspinlock on systems with Zacas and Zabha.
|
|
Add GPIO support to the simple helpers for the I2C OF component prober.
Components that the prober intends to probe likely require their
regulator supplies be enabled, and GPIOs be toggled to enable them or
bring them out of reset before they will respond to probe attempts.
Regulator supplies were handled in the previous patch.
The assumption is that the same class of components to be probed are
always connected in the same fashion with the same regulator supply
and GPIO. The names may vary due to binding differences, but the
physical layout does not change.
This supports at most one GPIO pin. The user must specify the GPIO name,
the polarity, and the amount of time to wait after the GPIO is toggled.
Devices with more than one GPIO pin likely require specific power
sequencing beyond what generic code can easily support.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add helpers to do regulator management for the I2C OF component prober.
Components that the prober intends to probe likely require their
regulator supplies be enabled, and GPIOs be toggled to enable them or
bring them out of reset before they will respond to probe attempts.
GPIOs will be handled in the next patch.
The assumption is that the same class of components to be probed are
always connected in the same fashion with the same regulator supply
and GPIO. The names may vary due to binding differences, but the
physical layout does not change.
This set of helpers supports at most one regulator supply. The user
must specify the node from which the supply is retrieved. The supply
name and the amount of time to wait after the supply is enabled are
also given by the user.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular device
can be detected by some firmware provided identifier, other times that
information is not available, and the kernel has to try to probe each
device.
This change attempts to make the "probe each device" case cleaner. The
current approach is to have all options added and enabled in the device
tree. The kernel would then bind each device and run each driver's probe
function. This works, but has been broken before due to the introduction
of asynchronous probing, causing multiple instances requesting "shared"
resources, such as pinmuxes, GPIO pins, interrupt lines, at the same
time, with only one instance succeeding. Work arounds for these include
moving the pinmux to the parent I2C controller, using GPIO hogs or
pinmux settings to keep the GPIO pins in some fixed configuration, and
requesting the interrupt line very late. Such configurations can be seen
on the MT8183 Krane Chromebook tablets, and the Qualcomm sc8280xp-based
Lenovo Thinkpad 13S.
Instead of this delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them responds.
It will then enable the device that responds.
This requires some minor modifications in the existing device tree. The
status for all the device nodes for the component options must be set
to "fail-needs-probe". This makes it clear that some mechanism is
needed to enable one of them, and also prevents the prober and device
drivers running at the same time.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
There are cases where drivers would go through child device nodes and
operate on only the ones whose node name starts with a given prefix.
Provide a helper for these users. This will mainly be used in a
subsequent patch that implements a hardware component prober for I2C
busses.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Add a helper function to add string property updates to an OF changeset.
This is similar to of_changeset_add_prop_string(), but instead of adding
the property (and failing if it exists), it will update the property.
This shall be used later in the DT hardware prober.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Core:
- avoid possible deadlock on probe
- ensured preferred address is used on hot-join
Drivers:
- dw: add AMD I3C controller support
- mipi-i3c-hci: fix SETDASA, DMA interrupts fixes
- svc: many fixes for IBI and hotjoin"
* tag 'i3c/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: Use i3cdev->desc->info instead of calling i3c_device_get_info() to avoid deadlock
i3c: mipi-i3c-hci: Support SETDASA CCC
i3c: dw: Add quirk to address OD/PP timing issue on AMD platform
i3c: dw: Add support for AMDI0015 ACPI ID
i3c: master: svc: Modify enabled_events bit 7:0 to act as IBI enable counter
i3c: Document I3C_ADDR_SLOT_EXT_STATUS_MASK
i3c: master: svc: Fix pm_runtime_set_suspended() with runtime pm enabled
i3c: mipi-i3c-hci: Handle interrupts according to current specifications
i3c: mipi-i3c-hci: Mask ring interrupts before ring stop request
i3c: master: Fix miss free init_dyn_addr at i3c_master_put_i3c_addrs()
i3c: master: Remove i3c_dev_disable_ibi_locked(olddev) on device hotjoin
i3c: master: svc: fix possible assignment of the same address to two devices
i3c: master: svc: wait for Manual ACK/NACK Done before next step
i3c: master: svc: use spin_lock_irqsave at svc_i3c_master_ibi_work()
i3c: master: svc: need check IBIWON for dynamic address assignment
i3c: master: svc: manually emit NACK/ACK for hotjoin
i3c: master: svc: use repeat start when IBI WIN happens
i3c: master: Fix dynamic address leak when 'assigned-address' is present
i3c: master: Extend address status bit to 4 and add I3C_ADDR_SLOT_EXT_DESIRED
i3c: master: Replace hard code 2 with macro I3C_ADDR_SLOT_STATUS_BITS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
callers can't stop a device multiple times, even as we migrate from
the global pci_rescan_remove_lock to finer-grained locking (Keith
Busch)
- Improve pci_walk_bus() implementation by making it recursive and
moving locking up to avoid need for a 'locked' parameter (Keith
Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by
the PCI core (Keith Busch)
- Detect some Thunderbolt chips that are built-in and hence
'trustworthy' by a heuristic since the 'ExternalFacingPort' and
'usb4-host-interface' ACPI properties are not quite enough (Esther
Shimanovich)
Resource management:
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties
when building dynamic DT nodes so systems where PCI and CPU
addresses differ work correctly (Andrea della Porta)
- Tidy resource sizing and assignment with helpers to reduce
redundancy (Ilpo Järvinen)
- Improve pdev_sort_resources() 'bogus alignment' warning to be more
specific (Ilpo Järvinen)
Driver binding:
- Convert driver .remove_new() callbacks to .remove() again to finish
the conversion from returning 'int' to being 'void' (Sergio
Paracuellos)
- Export pcim_request_all_regions(), a managed interface to request
all BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with
pcim_request_all_regions(), and pcim_iomap_table()[n] with
pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
(Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp
Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and
release a PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
cavium (Philipp Stanner)
Error handling:
- Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
bridge; previously Secondary Bus Reset could only be used when
there was a single device below a bridge (Keith Busch)
- Warn if we reset a running device where the driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
ASPM:
- Disable ASPM L1 before touching L1 PM Substates to follow the spec
closer and avoid a CPU load timeout on some platforms (Ajay
Agarwal)
- Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
as required per spec for all L1 Substates changes (Jian-Hong Pan)
Power management:
- Enable starfive controller runtime PM before probing host bridge
(Mayank Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
Power control:
- Use of_platform_device_create() instead of of_platform_populate()
to create pwrctl platform devices so we can control it based on the
child nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power
supply property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure
pwrctl drivers are probed before the PCI dev driver; this avoids a
race where pwrctl could change device power state while the PCI
driver was active (Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node()
instead of searching all children of the parent (Manivannan
Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
('bwctrl') and hotplug files (Bjorn Helgaas)
Bandwidth control:
- Add read/modify/write locking for Link Control 2, which is used to
manage Link speed (Ilpo Järvinen)
- Extract Link Bandwidth Management Status check into
pcie_lbms_seen(), where it can be shared between the bandwidth
controller and quirks that use it to help retrain failed links
(Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address
the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
Järvinen)
- Add pcie_set_target_speed() and related functionality so drivers
can manage PCIe Link speed based on thermal or other constraints
(Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the
existing thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
PCI device hotplug:
- Add hotplug controller driver for Marvell OCTEON multi-function
device where function 0 has a management console interface to
enable/disable and provision various personalities for the other
functions (Shijith Thotton)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to
avoid a use-after-free when the thunderbolt driver resets USB4 host
routers on boot, causing hotplug remove/add of downstream docks or
other devices (Lukas Wunner)
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
detection in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and
doesn't handle devices below hot-added bridges (Ilpo Järvinen)
Virtualization:
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
capability but do isolate functions as though PCI_ACS_RR and
PCI_ACS_CR were set, so the functions can be in independent IOMMU
groups (Mengyuan Lou)
TLP Processing Hints (TPH):
- Add and document TLP Processing Hints (TPH) support so drivers can
enable and disable TPH and the kernel can save/restore TPH
configuration (Wei Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag
values associated with specific CPUs via an ACPI _DSM to improve
performance by directing DMA writes closer to their consumers (Wei
Huang)
Data Object Exchange (DOE):
- Wait up to 1 second for DOE Busy bit to clear before writing a
request to the mailbox to avoid failures if the mailbox is still
busy from a previous transfer (Gregory Price)
Endpoint framework:
- Skip attempts to allocate from endpoint controller memory window if
the requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
handle controller-specific size and alignment constraints, and add
test cases to the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
observe DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
(Niklas Cassel)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks
'mmio' DT property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid
use-after-free (Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when
removing the secondary controller associated with an NTB (Zijun Hu)
Cadence PCIe controller driver:
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
Freescale i.MX6 PCIe controller driver:
- Fix suspend/resume support on i.MX6QDL, which has a hardware
erratum that prevents use of L2 (Stefan Eichenberger)
Intel VMD host bridge driver:
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 DT binding to require the exact number of
clocks for each SoC (Fei Shao)
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add DT and driver support for using either of the two PolarFire
Root Ports (Conor Dooley)
NVIDIA Tegra194 PCIe controller driver:
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
Qualcomm PCIe controller driver:
- Add qcom SAR2130P DT binding with an additional clock (Dmitry
Baryshkov)
- Enable MSI interrupts if 'global' IRQ is supported, since a
previous commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP
v5.80a and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the
qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
can be used by other Qcom platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the
link comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
to support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
'iommu-map' DT property and doesn't need BDF-to-SID translation
(Qiang Yu)
Rockchip PCIe controller driver:
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
.align value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead
of searching for it, and verify that the address was mapped (Damien
Le Moal)
- When mapping an endpoint window, verify that the address hasn't
been mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which
fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
(Damien Le Moal)
- Rename rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources() for consistency with similar DT
interfaces (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
it only in the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and
controller configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it
(Damien Le Moal)
- Add a handler for PERST# signal so we can detect host-initiated
resets and start link training after PERST# is deasserted (Damien
Le Moal)
Synopsys DesignWare PCIe controller driver:
- Clear outbound address on unmap so dw_pcie_find_index() won't match
an ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when
testing for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
TI J721E PCIe driver:
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
us), before deasserting PERST# to ensure power and refclk are
stable (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
Complex mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we
can do (Kishon Vijay Abraham I)
Miscellaneous:
- Reorganize kerneldoc parameter names to match order in function
signature (Julia Lawall)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)"
* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
tools: PCI: Fix incorrect printf format specifiers
...
|
|
Commit b1fca27d384e ("kernel debug: support resetting WARN*_ONCE")
added support for clearing the state of once warnings. However,
it is not functional when CONFIG_LD_DEAD_CODE_DATA_ELIMINATION or
CONFIG_LTO_CLANG is enabled, because .data.once matches the
.data.[0-9a-zA-Z_]* pattern in the DATA_MAIN macro.
Commit cb87481ee89d ("kbuild: linker script do not match C names unless
LD_DEAD_CODE_DATA_ELIMINATION is configured") was introduced to suppress
the issue for the default CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=n case,
providing a minimal fix for stable backporting. We were aware this did
not address the issue for CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y. The
plan was to apply correct fixes and then revert cb87481ee89d. [1]
Seven years have passed since then, yet the #ifdef workaround remains in
place. Meanwhile, commit b1fca27d384e introduced the .data.once section,
and commit dc5723b02e52 ("kbuild: add support for Clang LTO") extended
the #ifdef.
Using a ".." separator in the section name fixes the issue for
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION and CONFIG_LTO_CLANG.
[1]: https://lore.kernel.org/linux-kbuild/CAK7LNASck6BfdLnESxXUeECYL26yUDm0cwRZuM4gmaWUkxjL5g@mail.gmail.com/
Fixes: b1fca27d384e ("kernel debug: support resetting WARN*_ONCE")
Fixes: dc5723b02e52 ("kbuild: add support for Clang LTO")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Commit 7ccaba5314ca ("consolidate WARN_...ONCE() static variables")
was intended to collect all .data.unlikely sections into one chunk.
However, this has not worked when CONFIG_LD_DEAD_CODE_DATA_ELIMINATION
or CONFIG_LTO_CLANG is enabled, because .data.unlikely matches the
.data.[0-9a-zA-Z_]* pattern in the DATA_MAIN macro.
Commit cb87481ee89d ("kbuild: linker script do not match C names unless
LD_DEAD_CODE_DATA_ELIMINATION is configured") was introduced to suppress
the issue for the default CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=n case,
providing a minimal fix for stable backporting. We were aware this did
not address the issue for CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y. The
plan was to apply correct fixes and then revert cb87481ee89d. [1]
Seven years have passed since then, yet the #ifdef workaround remains in
place.
Using a ".." separator in the section name fixes the issue for
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION and CONFIG_LTO_CLANG.
[1]: https://lore.kernel.org/linux-kbuild/CAK7LNASck6BfdLnESxXUeECYL26yUDm0cwRZuM4gmaWUkxjL5g@mail.gmail.com/
Fixes: cb87481ee89d ("kbuild: linker script do not match C names unless LD_DEAD_CODE_DATA_ELIMINATION is configured")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Add the build support for using Clang's Propeller optimizer. Like
AutoFDO, Propeller uses hardware sampling to gather information
about the frequency of execution of different code paths within a
binary. This information is then used to guide the compiler's
optimization decisions, resulting in a more efficient binary.
The support requires a Clang compiler LLVM 19 or later, and the
create_llvm_prof tool
(https://github.com/google/autofdo/releases/tag/v0.30.1). This
commit is limited to x86 platforms that support PMU features
like LBR on Intel machines and AMD Zen3 BRS.
Here is an example workflow for building an AutoFDO+Propeller
optimized kernel:
1) Build the kernel on the host machine, with AutoFDO and Propeller
build config
CONFIG_AUTOFDO_CLANG=y
CONFIG_PROPELLER_CLANG=y
then
$ make LLVM=1 CLANG_AUTOFDO_PROFILE=<autofdo_profile>
“<autofdo_profile>” is the profile collected when doing a non-Propeller
AutoFDO build. This step builds a kernel that has the same optimization
level as AutoFDO, plus a metadata section that records basic block
information. This kernel image runs as fast as an AutoFDO optimized
kernel.
2) Install the kernel on test/production machines.
3) Run the load tests. The '-c' option in perf specifies the sample
event period. We suggest using a suitable prime number,
like 500009, for this purpose.
For Intel platforms:
$ perf record -e BR_INST_RETIRED.NEAR_TAKEN:k -a -N -b -c <count> \
-o <perf_file> -- <loadtest>
For AMD platforms:
The supported system are: Zen3 with BRS, or Zen4 with amd_lbr_v2
# To see if Zen3 support LBR:
$ cat proc/cpuinfo | grep " brs"
# To see if Zen4 support LBR:
$ cat proc/cpuinfo | grep amd_lbr_v2
# If the result is yes, then collect the profile using:
$ perf record --pfm-events RETIRED_TAKEN_BRANCH_INSTRUCTIONS:k -a \
-N -b -c <count> -o <perf_file> -- <loadtest>
4) (Optional) Download the raw perf file to the host machine.
5) Generate Propeller profile:
$ create_llvm_prof --binary=<vmlinux> --profile=<perf_file> \
--format=propeller --propeller_output_module_name \
--out=<propeller_profile_prefix>_cc_profile.txt \
--propeller_symorder=<propeller_profile_prefix>_ld_profile.txt
“create_llvm_prof” is the profile conversion tool, and a prebuilt
binary for linux can be found on
https://github.com/google/autofdo/releases/tag/v0.30.1 (can also build
from source).
"<propeller_profile_prefix>" can be something like
"/home/user/dir/any_string".
This command generates a pair of Propeller profiles:
"<propeller_profile_prefix>_cc_profile.txt" and
"<propeller_profile_prefix>_ld_profile.txt".
6) Rebuild the kernel using the AutoFDO and Propeller profile files.
CONFIG_AUTOFDO_CLANG=y
CONFIG_PROPELLER_CLANG=y
and
$ make LLVM=1 CLANG_AUTOFDO_PROFILE=<autofdo_profile> \
CLANG_PROPELLER_PROFILE_PREFIX=<propeller_profile_prefix>
Co-developed-by: Han Shen <shenhan@google.com>
Signed-off-by: Han Shen <shenhan@google.com>
Signed-off-by: Rong Xu <xur@google.com>
Suggested-by: Sriraman Tallam <tmsriram@google.com>
Suggested-by: Krzysztof Pszeniczny <kpszeniczny@google.com>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Stephane Eranian <eranian@google.com>
Tested-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Enable the machine function split optimization for AutoFDO in Clang.
Machine function split (MFS) is a pass in the Clang compiler that
splits a function into hot and cold parts. The linker groups all
cold blocks across functions together. This decreases hot code
fragmentation and improves iCache and iTLB utilization.
MFS requires a profile so this is enabled only for the AutoFDO builds.
Co-developed-by: Han Shen <shenhan@google.com>
Signed-off-by: Han Shen <shenhan@google.com>
Signed-off-by: Rong Xu <xur@google.com>
Suggested-by: Sriraman Tallam <tmsriram@google.com>
Suggested-by: Krzysztof Pszeniczny <kpszeniczny@google.com>
Tested-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Yabin Cui <yabinc@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Enable -ffunction-sections by default for the AutoFDO build.
With -ffunction-sections, the compiler places each function in its own
section named .text.function_name instead of placing all functions in
the .text section. In the AutoFDO build, this allows the linker to
utilize profile information to reorganize functions for improved
utilization of iCache and iTLB.
Co-developed-by: Han Shen <shenhan@google.com>
Signed-off-by: Han Shen <shenhan@google.com>
Signed-off-by: Rong Xu <xur@google.com>
Suggested-by: Sriraman Tallam <tmsriram@google.com>
Tested-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Yabin Cui <yabinc@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Add markers like __hot_text_start, __hot_text_end, __unlikely_text_start,
and __unlikely_text_end which will be included in System.map. These markers
indicate how the compiler groups functions, providing valuable information
to developers about the layout and optimization of the code.
Co-developed-by: Han Shen <shenhan@google.com>
Signed-off-by: Han Shen <shenhan@google.com>
Signed-off-by: Rong Xu <xur@google.com>
Suggested-by: Sriraman Tallam <tmsriram@google.com>
Tested-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Yabin Cui <yabinc@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
When the -ffunction-sections compiler option is enabled, each function
is placed in a separate section named .text.function_name rather than
putting all functions in a single .text section.
However, using -function-sections can cause problems with the
linker script. The comments included in include/asm-generic/vmlinux.lds.h
note these issues.:
“TEXT_MAIN here will match .text.fixup and .text.unlikely if dead
code elimination is enabled, so these sections should be converted
to use ".." first.”
It is unclear whether there is a straightforward method for converting
a suffix to "..".
This patch modifies the order of subsections within the text output
section. Specifically, it changes current order:
.text.hot, .text, .text_unlikely, .text.unknown, .text.asan
to the new order:
.text.asan, .text.unknown, .text_unlikely, .text.hot, .text
Here is the rationale behind the new layout:
The majority of the code resides in three sections: .text.hot, .text,
and .text.unlikely, with .text.unknown containing a negligible amount.
.text.asan is only generated in ASAN builds.
The primary goal is to group code segments based on their execution
frequency (hotness).
First, we want to place .text.hot adjacent to .text. Since we cannot put
.text.hot after .text (Due to constraints with -ffunction-sections,
placing .text.hot after .text is problematic), we need to put
.text.hot before .text.
Then it comes to .text.unlikely, we cannot put it after .text (same
-ffunction-sections issue) . Therefore, we position .text.unlikely
before .text.hot.
.text.unknown and .tex.asan follow the same logic.
This revised ordering effectively reverses the original arrangement (for
.text.unlikely, .text.unknown, and .tex.asan), maintaining a similar level
of affinity between sections.
It also places .text.hot section at the beginning of a page to better
utilize the TLB entry.
Note that the limitation arises because the linker script employs glob
patterns instead of regular expressions for string matching. While there
is a method to maintain the current order using complex patterns, this
significantly complicates the pattern and increases the likelihood of
errors.
This patch also changes vmlinux.lds.S for the sparc64 architecture to
accommodate specific symbol placement requirements.
Co-developed-by: Han Shen <shenhan@google.com>
Signed-off-by: Han Shen <shenhan@google.com>
Signed-off-by: Rong Xu <xur@google.com>
Suggested-by: Sriraman Tallam <tmsriram@google.com>
Suggested-by: Krzysztof Pszeniczny <kpszeniczny@google.com>
Tested-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Yabin Cui <yabinc@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs exportfs updates from Christian Brauner:
"This contains work to bring NFS connectable file handles to userspace
servers.
The name_to_handle_at() system call is extended to encode connectable
file handles. Such file handles can be resolved to an open file with a
connected path. So far userspace NFS servers couldn't make use of this
functionality even though the kernel does already support it. This is
achieved by introducing a new flag for name_to_handle_at().
Similarly, the open_by_handle_at() system call is tought to understand
connectable file handles explicitly created via name_to_handle_at()"
* tag 'vfs-6.13.exportfs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: open_by_handle_at() support for decoding "explicit connectable" file handles
fs: name_to_handle_at() support for "explicit connectable" file handles
fs: prepare for "explicit connectable" file handles
|
|
Pull nfsd updates from Chuck Lever:
"Jeff Layton contributed a scalability improvement to NFSD's NFSv4
backchannel session implementation. This improvement is intended to
increase the rate at which NFSD can safely recall NFSv4 delegations
from clients, to avoid the need to revoke them. Revoking requires a
slow state recovery process.
A wide variety of bug fixes and other incremental improvements make up
the bulk of commits in this series. As always I am grateful to the
NFSD contributors, reviewers, testers, and bug reporters who
participated during this cycle"
* tag 'nfsd-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux: (72 commits)
nfsd: allow for up to 32 callback session slots
nfs_common: must not hold RCU while calling nfsd_file_put_local
nfsd: get rid of include ../internal.h
nfsd: fix nfs4_openowner leak when concurrent nfsd4_open occur
NFSD: Add nfsd4_copy time-to-live
NFSD: Add a laundromat reaper for async copy state
NFSD: Block DESTROY_CLIENTID only when there are ongoing async COPY operations
NFSD: Handle an NFS4ERR_DELAY response to CB_OFFLOAD
NFSD: Free async copy information in nfsd4_cb_offload_release()
NFSD: Fix nfsd4_shutdown_copy()
NFSD: Add a tracepoint to record canceled async COPY operations
nfsd: make nfsd4_session->se_flags a bool
nfsd: remove nfsd4_session->se_bchannel
nfsd: make use of warning provided by refcount_t
nfsd: Don't fail OP_SETCLIENTID when there are too many clients.
svcrdma: fix miss destroy percpu_counter in svc_rdma_proc_init()
xdrgen: Remove program_stat_to_errno() call sites
xdrgen: Update the files included in client-side source code
xdrgen: Remove check for "nfs_ok" in C templates
xdrgen: Remove tracepoint call site
...
|
