| Age | Commit message (Collapse) | Author |
|---|
|
DSA implements a bunch of 'standardized' ethtool statistics counters,
namely tx_packets, tx_bytes, rx_packets, rx_bytes. So whatever the
hardware driver returns in .get_sset_count(), we need to add 4 to that.
That is ok, except that .get_sset_count() can return a negative error
code, for example:
b53_get_sset_count
-> phy_ethtool_get_sset_count
-> return -EIO
-EIO is -5, and with 4 added to it, it becomes -1, aka -EPERM. One can
imagine that certain error codes may even become positive, although
based on code inspection I did not see instances of that.
Check the error code first, if it is negative return it as-is.
Based on a similar patch for dsa_master_get_strings from Dan Carpenter:
https://patchwork.kernel.org/project/netdevbpf/patch/YJaSe3RPgn7gKxZv@mwanda/
Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If ds->ops->get_sset_count() fails then it "count" is a negative error
code such as -EOPNOTSUPP. Because "i" is an unsigned int, the negative
error code is type promoted to a very high value and the loop will
corrupt memory until the system crashes.
Fix this by checking for error codes and changing the type of "i" to
just int.
Fixes: badf3ada60ab ("net: dsa: Provide CPU port statistics to master netdev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case ethernet driver is enabled and INET is disabled, selftest will
fail to build.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 3e1e58d64c3d ("net: add generic selftest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210428130947.29649-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was a waste to clone skb directly in dsa_skb_tx_timestamp().
For one-step timestamping, a clone was not needed. For any failure of
port_txtstamp (this may usually happen), the skb clone had to be freed.
So this patch moves skb cloning for tx timestamp out of dsa core, and
let drivers clone skb in port_txtstamp if they really need.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move ptp_classify_raw out of dsa core driver for handling tx
timestamp request. Let device drivers do this if they want.
Not all drivers want to limit tx timestamping for only PTP
packet.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check tx timestamp request in core driver at very beginning of
dsa_skb_tx_timestamp(), so that most skbs not requiring tx
timestamp just return. And drop such checking in device drivers.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting with patch:
a8b659e7ff75 ("net: dsa: act as passthrough for bridge port flags")
drivers without "port_bridge_flags" callback will fail to join the bridge.
Looking at the code, -EOPNOTSUPP seems to be the proper return value,
which makes at least microchip and atheros switches work again.
Fixes: 5961d6a12c13 ("net: dsa: inherit the actual bridge port flags at join time")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some combinations of tag protocols and Ethernet controllers are
incompatible, and it is hard for the driver to keep track of these.
Therefore, allow the device tree author (typically the board vendor)
to inform the driver of this fact by selecting an alternate protocol
that is known to work.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously DSA ports were also included, on the assumption that the
protocol used by the CPU port had to the matched throughout the entire
tree.
As there is not yet any consumer in need of this, drop the call.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of generic selftest should be able to work with probably all ethernet
controllers. The DSA switches are not exception, so enable it by default at
least for DSA.
This patch was tested with SJA1105 and AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in bugfix commit 6ab4c3117aec ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.
Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If PHY is not available on DSA port (described at devicetree but absent or
failed to detect) then kernel prints warning after 3700 secs:
[ 3707.948771] ------------[ cut here ]------------
[ 3707.948784] Type was not set for devlink port.
[ 3707.948894] WARNING: CPU: 1 PID: 17 at net/core/devlink.c:8097 0xc083f9d8
We should unregister the devlink port as a user port and
re-register it as an unused port before executing "continue" in case of
dsa_port_setup error.
Fixes: 86f8b1c01a0a ("net: dsa: Do not make user port errors fatal")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify "Apparantly" to "Apparently" in net/dsa/tag_rtl4_a.c..
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA is aware of switches with global VLAN filtering since the blamed
commit, but it makes a bad decision when multiple bridges are spanning
the same switch:
ip link add br0 type bridge vlan_filtering 1
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br0
ip link set swp4 master br1
ip link set swp5 master br1
ip link set swp5 nomaster
ip link set swp4 nomaster
[138665.939930] sja1105 spi0.1: port 3: dsa_core: VLAN filtering is a global setting
[138665.947514] DSA: failed to notify DSA_NOTIFIER_BRIDGE_LEAVE
When all ports leave br1, DSA blindly attempts to disable VLAN filtering
on the switch, ignoring the fact that br0 still exists and is VLAN-aware
too. It fails while doing that.
This patch checks whether any port exists at all and is under a
VLAN-aware bridge.
Fixes: d371b7c92d19 ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa infrastructure provides a well-defined hierarchy of devices,
pass up the call to set up the flow block to the master device. From the
software dataplane, the netfilter infrastructure uses the dsa slave
devices to refer to the input and output device for the given skbuff.
Similarly, the flowtable definition in the ruleset refers to the dsa
slave port devices.
This patch adds the glue code to call ndo_setup_tc with TC_SETUP_FT
with the master device via the dsa slave devices.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add .ndo_fill_forward_path for dsa slave port devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we join an already-created bridge port, such as a bond master
interface, then we can miss the initial switchdev notifications emitted
by the bridge for this port, while it wasn't offloaded by anybody.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA currently assumes that the bridge port starts off with this
constellation of bridge port flags:
- learning on
- unicast flooding on
- multicast flooding on
- broadcast flooding on
just by virtue of code copy-pasta from the bridge layer (new_nbp).
This was a simple enough strategy thus far, because the 'bridge join'
moment always coincided with the 'bridge port creation' moment.
But with sandwiched interfaces, such as:
br0
|
bond0
|
swp0
it may happen that the user has had time to change the bridge port flags
of bond0 before enslaving swp0 to it. In that case, swp0 will falsely
assume that the bridge port flags are those determined by new_nbp, when
in fact this can happen:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
ip link set bond0 type bridge_slave learning off
ip link set swp0 master br0
Now swp0 has learning enabled, bond0 has learning disabled. Not nice.
Fix this by "dumpster diving" through the actual bridge port flags with
br_port_flag_is_set, at bridge join time.
We use this opportunity to split dsa_port_change_brport_flags into two
distinct functions called dsa_port_inherit_brport_flags and
dsa_port_clear_brport_flags, now that the implementation for the two
cases is no longer similar. This patch also creates two functions called
dsa_port_switchdev_sync and dsa_port_switchdev_unsync which collect what
we have so far, even if that's asymmetrical. More is going to be added
in the next patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a pretty noisy change that was broken out of the larger change
for replaying switchdev attributes and objects at bridge join time,
which is when these extack objects are actually used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bridge
DSA can properly detect and offload this sequence of operations:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set swp0 master bond0
ip link set bond0 master br0
But not this one:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
Actually the second one is more complicated, due to the elapsed time
between the enslavement of bond0 and the offloading of it via swp0, a
lot of things could have happened to the bond0 bridge port in terms of
switchdev objects (host MDBs, VLANs, altered STP state etc). So this is
a bit of a can of worms, and making sure that the DSA port's state is in
sync with this already existing bridge port is handled in the next
patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a temporary variable to hold the return value from
dsa_tag_driver_get() instead of assigning it to dst->tag_ops. Leaving
an error value in dst->tag_ops can result in deferencing an invalid
pointer when a deferred switch configuration happens later.
Fixes: 357f203bb3b5 ("net: dsa: keep a copy of the tagging protocol in the DSA switch tree")
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Remove CONFIG_HAVE_NET_DSA.
CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers
should have selected CONFIG_NET_DSA manually.
Currently, all drivers has explicit 'depends on NET_DSA', so this is
no more needed.
2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones.
- dropped !S390 dependency which was introduced to be sure NET_DSA
can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years
ago and the PHY library itself doesn't depend on !S390 since
commit 870a2b5e4fcd ("phylib: remove !S390 dependeny from Kconfig");
- INET dependency is kept to be sure we can select NET_SWITCHDEV;
- NETDEVICES dependency is kept to be sure we can select PHYLINK.
3. DSA drivers menu now depends on NET_DSA.
Instead on 'depends on NET_DSA' on every single driver, the entire
menu now depends on it. This eliminates a lot of duplicated lines
from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can
be only m or n).
This also has a nice side effect that there's no more empty menu on
configurations without DSA.
4. Kbuild will now descend into 'drivers/net/dsa' only when
CONFIG_NET_DSA is y or m.
This is safe since no objects inside this folder can be built without
DSA core, as well as when CONFIG_NET_DSA=m, no objects can be
built-in.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for a driver to be able to query a bridge for information
about itself, e.g. reading out port flags, it has to use a netdev that
is known to the bridge. In the simple case, that is just the netdev
representing the port, e.g. swp0 or swp1 in this example:
br0
/ \
swp0 swp1
But in the case of an offloaded lag, this will be the bond or team
interface, e.g. bond0 in this example:
br0
/
bond0
/ \
swp0 swp1
Add a helper that hides some of this complexity from the
drivers. Then, redefine dsa_port_offloads_bridge_port using the helper
to avoid double accounting of the set of possible offloaded uppers.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for legacy Broadcom tags, which are similar to DSA_TAG_PROTO_BRCM.
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now when extracting frames from CPU the cpuq is not used anymore so
remove it.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support port MDB and bridge flag operations.
As the hardware can manage multicast forwarding itself, offload_fwd_mark
can be unconditionally set to true.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ports
Tobias reports that after the blamed patch, VLAN objects being added to
a bridge device are being added to all slave ports instead (swp2, swp3).
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br0
bridge vlan add dev br0 vid 100 self
This is because the fix was too broad: we made dsa_port_offloads_netdev
say "yes, I offload the br0 bridge" for all slave ports, but we didn't
add the checks whether the switchdev object was in fact meant for the
physical port or for the bridge itself. So we are reacting on events in
a way in which we shouldn't.
The reason why the fix was too broad is because the question itself,
"does this DSA port offload this netdev", was too broad in the first
place. The solution is to disambiguate the question and separate it into
two different functions, one to be called for each switchdev attribute /
object that has an orig_dev == net_bridge (dsa_port_offloads_bridge),
and the other for orig_dev == net_bridge_port (*_offloads_bridge_port).
In the case of VLAN objects on the bridge interface, this solves the
problem because we know that VLAN objects are per bridge port and not
per bridge. And when orig_dev is equal to the net_bridge, we offload it
as a bridge, but not as a bridge port; that's how we are able to skip
reacting on those events. Note that this is compatible with future plans
to have explicit offloading of VLAN objects on the bridge interface as a
bridge port (in DSA, this signifies that we should add that VLAN towards
the CPU port).
Fixes: 99b8202b179f ("net: dsa: fix SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING getting ignored")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A different TPID bit is used for 802.1ad VLAN frames.
Reported-by: Ilario Gelmetti <iochesonome@gmail.com>
Fixes: f0af34317f4b ("net: dsa: mediatek: combine MediaTek tag with VLAN tag")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 86dd9868b878 has several issues, but was accepted too soon
before anyone could take a look.
- Double free. dsa_slave_xmit() will free the skb if the xmit function
returns NULL, but the skb is already freed by eth_skb_pad(). Use
__skb_put_padto() to avoid that.
- Unnecessary allocation. It has been done by DSA core since commit
a3b0b6479700.
- A u16 pointer points to skb data. It should be __be16 for network
byte order.
- Typo in comments. "numer" -> "number".
Fixes: 86dd9868b878 ("net: dsa: tag_rtl4_a: Support also egress tags")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the ocelot driver code is in a library, the dsa tag
code cannot be built-in:
ld.lld: error: undefined symbol: ocelot_can_inject
>>> referenced by tag_ocelot_8021q.c
>>> dsa/tag_ocelot_8021q.o:(ocelot_xmit) in archive net/built-in.a
ld.lld: error: undefined symbol: ocelot_port_inject_frame
>>> referenced by tag_ocelot_8021q.c
>>> dsa/tag_ocelot_8021q.o:(ocelot_xmit) in archive net/built-in.a
Building the tag support only really makes sense for compile-testing
when the driver is available, so add a Kconfig dependency that prevents
the broken configuration while allowing COMPILE_TEST alternative when
MSCC_OCELOT_SWITCH_LIB is disabled entirely. This case is handled
through the #ifdef check in include/soc/mscc/ocelot.h.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210225143910.3964364-2-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The core DSA framework uses hsr_is_master() which would not resolve to a
valid symbol if HSR is built-into the kernel and DSA is a module.
Fixes: 18596f504a3e ("net: dsa: add support for offloading HSR")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210220051222.15672-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support also transmitting frames using the custom "8899 A"
4 byte tag.
Qingfang came up with the solution: we need to pad the
ethernet frame to 60 bytes using eth_skb_pad(), then the
switch will happily accept frames with custom tags.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: efd7fe68f0c6 ("net: dsa: tag_rtl4_a: Implement Realtek 4 byte A tag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement functions 'port_mrp_add', 'port_mrp_del',
'port_mrp_add_ring_role' and 'port_mrp_del_ring_role' to call the mrp
functions from ocelot.
Also all MRP frames that arrive to CPU on queue number OCELOT_MRP_CPUQ
will be forward by the SW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for offloading MRP in HW. Currently implement the switchdev
calls 'SWITCHDEV_OBJ_ID_MRP', 'SWITCHDEV_OBJ_ID_RING_ROLE_MRP',
to allow to create MRP instances and to set the role of these instances.
Add DSA_NOTIFIER_MRP_ADD/DEL and DSA_NOTIFIER_MRP_ADD/DEL_RING_ROLE
which calls to .port_mrp_add/del and .port_mrp_add/del_ring_role in the
DSA driver for the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Smatch is confused by the fact that a 32-bit BIT(port) macro is passed
as argument to the ocelot_ifh_set_dest function and warns:
ocelot_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
seville_xmit() warn: should '(((1))) << (dp->index)' be a 64 bit type?
The destination port mask is copied into a 12-bit field of the packet,
starting at bit offset 67 and ending at 56.
So this DSA tagging protocol supports at most 12 bits, which is clearly
less than 32. Attempting to send to a port number > 12 will cause the
packing() call to truncate way before there will be 32-bit truncation
due to type promotion of the BIT(port) argument towards u64.
Therefore, smatch's fears that BIT(port) will do the wrong thing and
cause unexpected truncation for "port" values >= 32 are unfounded.
Nonetheless, let's silence the warning by explicitly passing an u64
value to ocelot_ifh_set_dest, such that the compiler does not need to do
a questionable type promotion.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the tag_8021q tagger is software-defined, it has no means by
itself for retrieving hardware timestamps of PTP event messages.
Because we do want to support PTP on ocelot even with tag_8021q, we need
to use the CPU port module for that. The RX timestamp is present in the
Extraction Frame Header. And because we can't use NPI mode which redirects
the CPU queues to an "external CPU" (meaning the ARM CPU running Linux),
then we need to poll the CPU port module through the MMIO registers to
retrieve TX and RX timestamps.
Sadly, on NXP LS1028A, the Felix switch was integrated into the SoC
without wiring the extraction IRQ line to the ARM GIC. So, if we want to
be notified of any PTP packets received on the CPU port module, we have
a problem.
There is a possible workaround, which is to use the Ethernet CPU port as
a notification channel that packets are available on the CPU port module
as well. When a PTP packet is received by the DSA tagger (without timestamp,
of course), we go to the CPU extraction queues, poll for it there, then
we drop the original Ethernet packet and masquerade the packet retrieved
over MMIO (plus the timestamp) as the original when we inject it up the
stack.
Create a quirk in struct felix is selected by the Felix driver (but not
by Seville, since that doesn't support PTP at all). We want to do this
such that the workaround is minimally invasive for future switches that
don't require this workaround.
The only traffic for which we need timestamps is PTP traffic, so add a
redirection rule to the CPU port module for this. Currently we only have
the need for PTP over L2, so redirection rules for UDP ports 319 and 320
are TBD for now.
Note that for the workaround of matching of PTP-over-Ethernet-port with
PTP-over-MMIO queues to work properly, both channels need to be
absolutely lossless. There are two parts to achieving that:
- We keep flow control enabled on the tag_8021q CPU port
- We put the DSA master interface in promiscuous mode, so it will never
drop a PTP frame (for the profiles we are interested in, these are
sent to the multicast MAC addresses of 01-80-c2-00-00-0e and
01-1b-19-00-00-00).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot tagger is a hot mess currently, it relies on memory
initialized by the attached driver for basic frame transmission.
This is against all that DSA tagging protocols stand for, which is that
the transmission and reception of a DSA-tagged frame, the data path,
should be independent from the switch control path, because the tag
protocol is in principle hot-pluggable and reusable across switches
(even if in practice it wasn't until very recently). But if another
driver like dsa_loop wants to make use of tag_ocelot, it couldn't.
This was done to have common code between Felix and Ocelot, which have
one bit difference in the frame header format. Quoting from commit
67c2404922c2 ("net: dsa: felix: create a template for the DSA tags on
xmit"):
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
The really interesting part is that Seville should have had its own
tagging protocol defined - it is not compatible on the wire with Ocelot,
even for that single bit. In principle, a packet generated by
DSA_TAG_PROTO_OCELOT when booted on NXP LS1028A would look in a certain
way, but when booted on NXP T1040 it would look differently. The reverse
is also true: a packet generated by a Seville switch would be
interpreted incorrectly by Wireshark if it was told it was generated by
an Ocelot switch.
Actually things are a bit more nuanced. If we concentrate only on the
DSA tag, what I said above is true, but Ocelot/Seville also support an
optional DSA tag prefix, which can be short or long, and it is possible
to distinguish the two taggers based on an integer constant put in that
prefix. Nonetheless, creating a separate tagger is still justified,
since the tag prefix is optional, and without it, there is again no way
to distinguish.
Claiming backwards binary compatibility is a bit more tough, since I've
already changed the format of tag_ocelot once, in commit 5124197ce58b
("net: dsa: tag_ocelot: use a short prefix on both ingress and egress").
Therefore I am not very concerned with treating this as a bugfix and
backporting it to stable kernels (which would be another mess due to the
fact that there would be lots of conflicts with the other DSA_TAG_PROTO*
definitions). It's just simpler to say that the string values of the
taggers have ABI value starting with kernel 5.12, which will be when the
changing of tag protocol via /sys/class/net/<dsa-master>/dsa/tagging
goes live.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is one place where we cannot avoid accessing driver data, and that
is 2-step PTP TX timestamping, since the switch wants us to provide a
timestamp request ID through the injection header, which naturally must
come from a sequence number kept by the driver (it is generated by the
.port_txtstamp method prior to the tagger's xmit).
However, since other drivers like dsa_loop do not claim PTP support
anyway, the DSA_SKB_CB(skb)->clone will always be NULL anyway, so if we
move all PTP-related dereferences of struct ocelot and struct ocelot_port
into a separate function, we can effectively ensure that this is dead
code when the ocelot tagger is attached to non-ocelot switches, and the
stateful portion of the tagger is more self-contained.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taggers should be written to do something valid irrespective of the
switch driver that they are attached to. This is even more true now,
because since the introduction of the .change_tag_protocol method, a
certain tagger is not necessarily strictly associated with a driver any
longer, and I would like to be able to test all taggers with dsa_loop in
the future.
In the case of ocelot, it needs to move the classified VLAN from the DSA
tag into the skb if the port is VLAN-aware. We can allow it to do that
by looking at the dp->vlan_filtering property, no need to invoke
structures which are specific to ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.
One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.
Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.
Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it. If it does, there
will need to be a dedicated .port_set_mrouter anyway.
So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.
The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:
behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)
so there was no reason to entangle them in the first place.
Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
