| Age | Commit message (Collapse) | Author |
|---|
|
cs35l56_remove() always returns 0. Two of the functions that call
it are void and the other one should only return 0. So there's no
point returning anything from cs35l56_remove().
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230414133753.653139-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dsp_ready_completion is redundant and can be replaced by a call
flush_work() to wait for cs35l56_dsp_work() to complete.
As the dsp_work is queued by component_probe() it must run before other
ASoC component callbacks and therefore there is no risk of calling
flush_work() before the dsp_work() has been queued.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230414133753.653139-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The irq member was being set before calling the init function and then
cs35l56_irq_request() was called only when the init was successful.
However cs35l56_release() calls devm_free_irq() when the irq member is
set and therefore if init() fails then this will cause an attempted free
of an unallocated IRQ.
Instead pass the desired IRQ number to the cs35l56_irq_request()
function and set cs35l56->irq only when it has been successfully
allocated.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168147949598.26.711670799488943454@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Delete the 'removing' flag and don't kick init_completion to make a
quick cancel of dsp_work(). Just let it timeout on the wait for the
completion.
Simplify the code to standard cancelling or flushing of the work.
This avoids introducing corner cases from a layer of custom signalling.
It also avoids potential race conditions when system-suspend handling
is added.
Unless the hardware is broken, the dsp_work() will already have started
and passed the completion before the driver would want to cancel it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168122674746.26.16881587647873355224@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds the main handling for system suspend but does not handle
re-patching the firmware after system resume.
This is a multi-stage suspend and resume because if there is a
RESET line it is almost certain that it will be shared by all the
amps. So every amp must have done its suspend before we can
assert RESET. Likewise we must de-assert RESET before the amps
can resume.
It's preferable to assert RESET before we turning off regulators, and
while they power up.
The actual suspend and resume is done by using the pair
pm_runtime_force_suspend() and pm_runtime_force_resume() to
re-use our runtime suspend/resume sequences.
pm_runtime_force_suspend() will disable our pm_runtime. If we were
runtime-resumed it calls our runtime_suspend().
pm_runtime_force_resume() re-enables pm_runtime and if we were
originally runtime-resumed before the pm_runtime_force_suspend()
it calls our runtime_resume(). Otherwise it leaves us
runtime-suspended.
The general process is therefore:
suspend() -> finish dsp_work and then run our runtime_suspend
suspend_late() -> assert RESET and turn off supplies
resume_early() -> enable supplies and de-assert RESET
resume() -> pm_runtime_force_resume()
In addition, to prevent the IRQ handler running in the period
between pm_runtime_force_suspend() and pm_runtime_force_resume()
the parent IRQ is temporarily disabled:
- from suspend until suspend_noirq
- from resume_noirq until resume
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230411152528.329803-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CS35L56 combines a high-performance mono audio amplifier, Class-H
tracking inductive boost converter, Halo Core(TM) DSP and a DC-DC boost
converter supporting Class-H tracking.
Supported control interfaces are I2C, SPI or SoundWire.
Supported audio interfaces are I2S/TDM or SoundWire.
Most chip functionality is controlled by on-board ROM firmware that is
always running. The driver must apply patch/tune to the firmware
before using the CS35L56.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230320112245.115720-9-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
