| Age | Commit message (Collapse) | Author |
|---|
|
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Replace snd_soc_register_card with devm_snd_soc_register_card.
With this change, we can delete the empty remove functions.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
Previously, the ASoC 'platform' (PCM/DMA) object was instantiated via a
platform_device. This didn't represent the hardware well, since there
was no separate hardware associated with this platform_device; it was a
virtual device with sole purpose to call snd_soc_register_platform().
This change removes the platform_device completely. Each Samsung DAI now
registers the ASoC 'platform' itself. Machine drivers are adjusted for
the new 'platform' name.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Allow custom accessory identification mechanisms to make use of the MICDET
support in the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Since we only need to clock AIF2 when it's actively in use start up the
FLL for it using a supply widget which supplies AIF2CLK. This both makes
the sequencing more robust and ensures we minimise power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Connect the WM1250-EV1 baseband simulator on Littlemill systems up to
the CODEC AIF2 using the new CODEC<->CODEC link support, allowing a wider
range of use cases to be represented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The WM8994 has a different accessory detect architecture, call its setup
function too. We ignore the errors and the driver will check for chip type
so it's safe to call the setup functions for both architectures.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Littlemill has one analogue microphone on the board (connected to IN1LN)
and an array of four DMICs connected to both DMICDAT lines. The biases
can be selected by jumpers but pick the default jumper fit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The board supports CODECs that won't work with this but the CODEC driver
will check to see if it's running on the right chip for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The Littlemill audio card supports a number of pluggable miniboards,
normally for the WM8994 family of devices. As all these devices look
mostly the same from an external configuration point of view and are
runtime enumerable we can write a standard machine driver which will
work out of the box with any of them. Start doing that with the bare
bones of a driver, only supporting AIF1.
Future patches will flesh this out to be more fully featured.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
