From 599c376c49323127c9bdbb0fa61a3d4743819bc2 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 18 Mar 2015 13:41:34 -0700 Subject: ARM: dts: Fix gpio interrupts for dm816x Commit 7800064ba507 ("ARM: dts: Add basic dm816x device tree configuration") added basic devices for dm816x, but I was not able to test the GPIO interrupts earlier until I found some suitable pins to test with. We can mux the MMC card detect and write protect pins from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that are also suitable for the MMC subsystem. This turned out several issues that need to be fixed: - I set the GPIO type wrong to be compatible with omap3 instead of omap4. The GPIO controller on dm816x has EOI interrupt register like omap4 and am335x. - I got the GPIO interrupt numbers wrong as each bank has two and we only use one. They need to be set up the same way as on am335x. - The gpio banks are missing interrupt controller related properties. With these changes the GPIO interrupts can be used with the MMC card detect pin, so let's wire that up. Let's also mux all the MMC lines for completeness while at it. For the first GPIO bank I tested using GPMC lines temporarily muxed to GPIOs on the dip switch 10. Cc: Brian Hutchinson Cc: Matthijs van Duin Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dm8168-evm.dts | 19 +++++++++++++++++++ arch/arm/boot/dts/dm816x.dtsi | 18 ++++++++++++++---- 2 files changed, 33 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts index d3a29c1b8417..afe678f6d2e9 100644 --- a/arch/arm/boot/dts/dm8168-evm.dts +++ b/arch/arm/boot/dts/dm8168-evm.dts @@ -36,6 +36,20 @@ >; }; + mmc_pins: pinmux_mmc_pins { + pinctrl-single,pins = < + DM816X_IOPAD(0x0a70, MUX_MODE0) /* SD_POW */ + DM816X_IOPAD(0x0a74, MUX_MODE0) /* SD_CLK */ + DM816X_IOPAD(0x0a78, MUX_MODE0) /* SD_CMD */ + DM816X_IOPAD(0x0a7C, MUX_MODE0) /* SD_DAT0 */ + DM816X_IOPAD(0x0a80, MUX_MODE0) /* SD_DAT1 */ + DM816X_IOPAD(0x0a84, MUX_MODE0) /* SD_DAT2 */ + DM816X_IOPAD(0x0a88, MUX_MODE0) /* SD_DAT2 */ + DM816X_IOPAD(0x0a8c, MUX_MODE2) /* GP1[7] */ + DM816X_IOPAD(0x0a90, MUX_MODE2) /* GP1[8] */ + >; + }; + usb0_pins: pinmux_usb0_pins { pinctrl-single,pins = < DM816X_IOPAD(0x0d00, MUX_MODE0) /* USB0_DRVVBUS */ @@ -137,7 +151,12 @@ }; &mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc_pins>; vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; + cd-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; }; /* At least dm8168-evm rev c won't support multipoint, later may */ diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index 3c97b5f2addc..f35715bc6992 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -150,17 +150,27 @@ }; gpio1: gpio@48032000 { - compatible = "ti,omap3-gpio"; + compatible = "ti,omap4-gpio"; ti,hwmods = "gpio1"; + ti,gpio-always-on; reg = <0x48032000 0x1000>; - interrupts = <97>; + interrupts = <96>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; }; gpio2: gpio@4804c000 { - compatible = "ti,omap3-gpio"; + compatible = "ti,omap4-gpio"; ti,hwmods = "gpio2"; + ti,gpio-always-on; reg = <0x4804c000 0x1000>; - interrupts = <99>; + interrupts = <98>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; }; gpmc: gpmc@50000000 { -- cgit v1.2.3-70-g09d2