From f5786b8e934e77f76f689c515baa582ff5a196ec Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Fri, 21 Jun 2013 15:36:11 +0200 Subject: ARM i.MX53: Fix UART pad configuration The current default pad configuration for UART RX and TX pads sets a 360k pull-down and writes 1 to a reserved bit (1 << 0). It doesn't seem right to me that in idle state, the UART has to keep the signal high against a pull-down resistor. This patch instead sets a 100k pull-up, which incidentally corresponds to the register reset value for all but one (MX53_PAD_KEY_ROW0__UART4_RXD_MUX) pad, and removes the write to the reserved bit. Signed-off-by: Philipp Zabel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx53.dtsi | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index 3895fbba8fce..569aa9f2c4ed 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -725,15 +725,15 @@ uart1 { pinctrl_uart1_1: uart1grp-1 { fsl,pins = < - MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1c5 - MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1c5 + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 >; }; pinctrl_uart1_2: uart1grp-2 { fsl,pins = < - MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1c5 - MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1c5 + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 >; }; @@ -748,8 +748,8 @@ uart2 { pinctrl_uart2_1: uart2grp-1 { fsl,pins = < - MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1c5 - MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1c5 + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 >; }; @@ -766,17 +766,17 @@ uart3 { pinctrl_uart3_1: uart3grp-1 { fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1c5 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1c5 - MX53_PAD_PATA_DA_1__UART3_CTS 0x1c5 - MX53_PAD_PATA_DA_2__UART3_RTS 0x1c5 + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 + MX53_PAD_PATA_DA_1__UART3_CTS 0x1e4 + MX53_PAD_PATA_DA_2__UART3_RTS 0x1e4 >; }; pinctrl_uart3_2: uart3grp-2 { fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1c5 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1c5 + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 >; }; @@ -785,8 +785,8 @@ uart4 { pinctrl_uart4_1: uart4grp-1 { fsl,pins = < - MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1c5 - MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1c5 + MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4 + MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4 >; }; }; @@ -794,8 +794,8 @@ uart5 { pinctrl_uart5_1: uart5grp-1 { fsl,pins = < - MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1c5 - MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1c5 + MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4 + MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4 >; }; }; -- cgit v1.2.3-70-g09d2 From 66acaf3f897c9245f5456d884e5ae401700cbc45 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Mon, 1 Jul 2013 15:46:05 +0800 Subject: ARM: mxs: saif0 is the clock provider to sgtl5000 These systems all use saif0 as the mclock provider to codec sgtl5000. Reflect that in device tree source, so that sgtl5000 can find the clock by calling clk_get(). Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28-apx4devkit.dts | 2 +- arch/arm/boot/dts/imx28-evk.dts | 2 +- arch/arm/boot/dts/imx28-m28evk.dts | 2 +- arch/arm/boot/dts/imx28.dtsi | 1 + 4 files changed, 4 insertions(+), 3 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts index 43bf3c796cba..0e7fed47bd8d 100644 --- a/arch/arm/boot/dts/imx28-apx4devkit.dts +++ b/arch/arm/boot/dts/imx28-apx4devkit.dts @@ -147,7 +147,7 @@ reg = <0x0a>; VDDA-supply = <®_3p3v>; VDDIO-supply = <®_3p3v>; - + clocks = <&saif0>; }; pcf8563: rtc@51 { diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index 1f0d38d7b16f..e035f4664b97 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -195,7 +195,7 @@ reg = <0x0a>; VDDA-supply = <®_3p3v>; VDDIO-supply = <®_3p3v>; - + clocks = <&saif0>; }; at24@51 { diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index 880df2f13be8..44d9da57736e 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -184,7 +184,7 @@ reg = <0x0a>; VDDA-supply = <®_3p3v>; VDDIO-supply = <®_3p3v>; - + clocks = <&saif0>; }; eeprom: eeprom@51 { diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 6a8acb01b1d3..9524a0571281 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -837,6 +837,7 @@ compatible = "fsl,imx28-saif"; reg = <0x80042000 0x2000>; interrupts = <59 80>; + #clock-cells = <0>; clocks = <&clks 53>; dmas = <&dma_apbx 4>; dma-names = "rx-tx"; -- cgit v1.2.3-70-g09d2 From 4f71612ee3a1b2d15c8246d926a40c4f7d21cc3b Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Wed, 10 Jul 2013 14:05:44 +0800 Subject: ARM: imx: fix vf610 enet module clock selection The fec/enet driver calculates MDC rate with the formula below. ref_freq / ((MII_SPEED + 1) x 2) The ref_freq here is the fec internal module clock, which is missing from clk-vf610 clock driver right now. And clk-vf610 driver mistakenly supplies RMII clock (50 MHz) as the source to fec. This results in the situation that fec driver gets ref_freq as 50 MHz, while physically it runs at 66 MHz (fec module clock physically sources from ipg which runs at 66 MHz). That's why software expects MDC runs at 2.5 MHz, while the measurement tells it runs at 3.3 MHz. And this causes the PHY KSZ8041 keeps swithing between Full and Half mode as below. libphy: 400d0000.etherne:00 - Link is Up - 100/Full libphy: 400d0000.etherne:00 - Link is Up - 100/Half libphy: 400d0000.etherne:00 - Link is Up - 100/Full libphy: 400d0000.etherne:00 - Link is Up - 100/Half libphy: 400d0000.etherne:00 - Link is Up - 100/Full libphy: 400d0000.etherne:00 - Link is Up - 100/Half Add the missing module clock for ENET0 and ENET1, and correct the clock supplying in device tree to fix above issue. Thanks to Alison Wang for debugging the issue. Signed-off-by: Shawn Guo --- arch/arm/boot/dts/vf610.dtsi | 8 ++++---- arch/arm/mach-imx/clk-vf610.c | 2 ++ include/dt-bindings/clock/vf610-clock.h | 4 +++- 3 files changed, 9 insertions(+), 5 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi index e1eb7dadda80..67d929cf9804 100644 --- a/arch/arm/boot/dts/vf610.dtsi +++ b/arch/arm/boot/dts/vf610.dtsi @@ -442,8 +442,8 @@ compatible = "fsl,mvf600-fec"; reg = <0x400d0000 0x1000>; interrupts = <0 78 0x04>; - clocks = <&clks VF610_CLK_ENET>, - <&clks VF610_CLK_ENET>, + clocks = <&clks VF610_CLK_ENET0>, + <&clks VF610_CLK_ENET0>, <&clks VF610_CLK_ENET>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; @@ -453,8 +453,8 @@ compatible = "fsl,mvf600-fec"; reg = <0x400d1000 0x1000>; interrupts = <0 79 0x04>; - clocks = <&clks VF610_CLK_ENET>, - <&clks VF610_CLK_ENET>, + clocks = <&clks VF610_CLK_ENET1>, + <&clks VF610_CLK_ENET1>, <&clks VF610_CLK_ENET>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; diff --git a/arch/arm/mach-imx/clk-vf610.c b/arch/arm/mach-imx/clk-vf610.c index d617c0b7c809..b169a396d93b 100644 --- a/arch/arm/mach-imx/clk-vf610.c +++ b/arch/arm/mach-imx/clk-vf610.c @@ -183,6 +183,8 @@ static void __init vf610_clocks_init(struct device_node *ccm_node) clk[VF610_CLK_ENET_TS_SEL] = imx_clk_mux("enet_ts_sel", CCM_CSCMR2, 0, 3, enet_ts_sels, 7); clk[VF610_CLK_ENET] = imx_clk_gate("enet", "enet_sel", CCM_CSCDR1, 24); clk[VF610_CLK_ENET_TS] = imx_clk_gate("enet_ts", "enet_ts_sel", CCM_CSCDR1, 23); + clk[VF610_CLK_ENET0] = imx_clk_gate2("enet0", "ipg_bus", CCM_CCGR9, CCM_CCGRx_CGn(0)); + clk[VF610_CLK_ENET1] = imx_clk_gate2("enet1", "ipg_bus", CCM_CCGR9, CCM_CCGRx_CGn(1)); clk[VF610_CLK_PIT] = imx_clk_gate2("pit", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(7)); diff --git a/include/dt-bindings/clock/vf610-clock.h b/include/dt-bindings/clock/vf610-clock.h index 15e997fa78f2..4aa2b48cd151 100644 --- a/include/dt-bindings/clock/vf610-clock.h +++ b/include/dt-bindings/clock/vf610-clock.h @@ -158,6 +158,8 @@ #define VF610_CLK_GPU_SEL 145 #define VF610_CLK_GPU_EN 146 #define VF610_CLK_GPU2D 147 -#define VF610_CLK_END 148 +#define VF610_CLK_ENET0 148 +#define VF610_CLK_ENET1 149 +#define VF610_CLK_END 150 #endif /* __DT_BINDINGS_CLOCK_VF610_H */ -- cgit v1.2.3-70-g09d2 From 15968f1bd4341cfa54023348a4e0b94798211742 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Thu, 11 Jul 2013 16:37:47 +0200 Subject: ARM i.MX53: mba53: Fix PWM backlight DT node The i.MX53 PWM controller uses two cells to describe the PWM specifier. Remove the extra unused values from the backlight DT node pwms property. Signed-off-by: Laurent Pinchart Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx53-mba53.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts index aaa33bc99f78..a63090267941 100644 --- a/arch/arm/boot/dts/imx53-mba53.dts +++ b/arch/arm/boot/dts/imx53-mba53.dts @@ -27,7 +27,7 @@ backlight { compatible = "pwm-backlight"; - pwms = <&pwm2 0 50000 0 0>; + pwms = <&pwm2 0 50000>; brightness-levels = <0 24 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100>; default-brightness-level = <10>; enable-gpios = <&gpio7 7 0>; -- cgit v1.2.3-70-g09d2 From 13782a7e2821f62efc747fd26605de4dc823ee29 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 7 Jun 2013 15:01:58 -0700 Subject: ARM: dts: Add missing vmmc2 regulator for twl For some reason vmmc2 regulator is missing for twl. Let's add it. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/twl4030.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi index b3034da00a37..ae6a17aed9ee 100644 --- a/arch/arm/boot/dts/twl4030.dtsi +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -47,6 +47,12 @@ regulator-max-microvolt = <3150000>; }; + vmmc2: regulator-vmmc2 { + compatible = "ti,twl4030-vmmc2"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; + }; + vusb1v5: regulator-vusb1v5 { compatible = "ti,twl4030-vusb1v5"; }; -- cgit v1.2.3-70-g09d2 From 84bb08472520882394fe16d7a3548793302563de Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Sun, 9 Jun 2013 22:07:47 -0300 Subject: ARM: dts: imx51-babbage: Pass a real clock to the codec On imx51_babbage the codec clock is activated via GPIO4_26. Provide a real clock to the sgtl5000 codec via device tree. Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx51-babbage.dts | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts index 6dd9486c755b..ad3471ca17c7 100644 --- a/arch/arm/boot/dts/imx51-babbage.dts +++ b/arch/arm/boot/dts/imx51-babbage.dts @@ -61,6 +61,16 @@ mux-int-port = <2>; mux-ext-port = <3>; }; + + clocks { + clk_26M: codec_clock { + compatible = "fixed-clock"; + reg=<0>; + #clock-cells = <0>; + clock-frequency = <26000000>; + gpios = <&gpio4 26 1>; + }; + }; }; &esdhc1 { @@ -229,6 +239,7 @@ MX51_PAD_EIM_A27__GPIO2_21 0x5 MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 MX51_PAD_CSPI1_SS1__GPIO4_25 0x85 + MX51_PAD_CSPI1_RDY__GPIO4_26 0x80000000 >; }; }; @@ -255,7 +266,7 @@ sgtl5000: codec@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; - clock-frequency = <26000000>; + clocks = <&clk_26M>; VDDA-supply = <&vdig_reg>; VDDIO-supply = <&vvideo_reg>; }; -- cgit v1.2.3-70-g09d2 From a39a9f7b6608c83b89ae404cc39e6607ccdccdde Mon Sep 17 00:00:00 2001 From: Rohit Vaswani Date: Tue, 18 Jun 2013 18:53:31 -0700 Subject: ARM: msm: dts: Fix the gpio register address for msm8960 Fix the the gpio reg address for the device tree entry. Signed-off-by: Rohit Vaswani Signed-off-by: David Brown --- arch/arm/boot/dts/msm8960-cdp.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/msm8960-cdp.dts b/arch/arm/boot/dts/msm8960-cdp.dts index db2060c46540..9c1167b0459b 100644 --- a/arch/arm/boot/dts/msm8960-cdp.dts +++ b/arch/arm/boot/dts/msm8960-cdp.dts @@ -26,7 +26,7 @@ cpu-offset = <0x80000>; }; - msmgpio: gpio@fd510000 { + msmgpio: gpio@800000 { compatible = "qcom,msm-gpio"; gpio-controller; #gpio-cells = <2>; @@ -34,7 +34,7 @@ interrupts = <0 32 0x4>; interrupt-controller; #interrupt-cells = <2>; - reg = <0xfd510000 0x4000>; + reg = <0x800000 0x4000>; }; serial@16440000 { -- cgit v1.2.3-70-g09d2 From d58e9a02e1435744d80a99742d1135a6921318eb Mon Sep 17 00:00:00 2001 From: Qipan Li Date: Thu, 4 Jul 2013 15:55:26 +0800 Subject: pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl this patch adds the lost pin group which supports to let USP0 to simulate a UART without hardware flow control. Signed-off-by: Qipan Li Signed-off-by: Barry Song Signed-off-by: Linus Walleij --- arch/arm/boot/dts/atlas6.dtsi | 6 ++++++ drivers/pinctrl/sirf/pinctrl-atlas6.c | 20 ++++++++++++++++++++ 2 files changed, 26 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/atlas6.dtsi b/arch/arm/boot/dts/atlas6.dtsi index 9866cd736dee..537041253db7 100644 --- a/arch/arm/boot/dts/atlas6.dtsi +++ b/arch/arm/boot/dts/atlas6.dtsi @@ -485,6 +485,12 @@ sirf,function = "usp0"; }; }; + usp0_uart_nostreamctrl_pins_a: usp0@1 { + usp0 { + sirf,pins = "usp0_uart_nostreamctrl_grp"; + sirf,function = "usp0_uart_nostreamctrl"; + }; + }; usp1_pins_a: usp1@0 { usp1 { sirf,pins = "usp1grp"; diff --git a/drivers/pinctrl/sirf/pinctrl-atlas6.c b/drivers/pinctrl/sirf/pinctrl-atlas6.c index c641be9c5b80..867c9681763c 100644 --- a/drivers/pinctrl/sirf/pinctrl-atlas6.c +++ b/drivers/pinctrl/sirf/pinctrl-atlas6.c @@ -509,6 +509,19 @@ static const struct sirfsoc_padmux usp0_padmux = { static const unsigned usp0_pins[] = { 51, 52, 53, 54, 55 }; +static const struct sirfsoc_muxmask usp0_uart_nostreamctrl_muxmask[] = { + { + .group = 1, + .mask = BIT(20) | BIT(21), + }, +}; + +static const struct sirfsoc_padmux usp0_uart_nostreamctrl_padmux = { + .muxmask_counts = ARRAY_SIZE(usp0_uart_nostreamctrl_muxmask), + .muxmask = usp0_uart_nostreamctrl_muxmask, +}; + +static const unsigned usp0_uart_nostreamctrl_pins[] = { 52, 53 }; static const struct sirfsoc_muxmask usp1_muxmask[] = { { .group = 0, @@ -822,6 +835,8 @@ static const struct sirfsoc_pin_group sirfsoc_pin_groups[] = { SIRFSOC_PIN_GROUP("uart2grp", uart2_pins), SIRFSOC_PIN_GROUP("uart2_nostreamctrlgrp", uart2_nostreamctrl_pins), SIRFSOC_PIN_GROUP("usp0grp", usp0_pins), + SIRFSOC_PIN_GROUP("usp0_uart_nostreamctrl_grp", + usp0_uart_nostreamctrl_pins), SIRFSOC_PIN_GROUP("usp1grp", usp1_pins), SIRFSOC_PIN_GROUP("i2c0grp", i2c0_pins), SIRFSOC_PIN_GROUP("i2c1grp", i2c1_pins), @@ -862,6 +877,8 @@ static const char * const uart0grp[] = { "uart0grp" }; static const char * const uart1grp[] = { "uart1grp" }; static const char * const uart2grp[] = { "uart2grp" }; static const char * const uart2_nostreamctrlgrp[] = { "uart2_nostreamctrlgrp" }; +static const char * const usp0_uart_nostreamctrl_grp[] = { + "usp0_uart_nostreamctrl_grp" }; static const char * const usp0grp[] = { "usp0grp" }; static const char * const usp1grp[] = { "usp1grp" }; static const char * const i2c0grp[] = { "i2c0grp" }; @@ -904,6 +921,9 @@ static const struct sirfsoc_pmx_func sirfsoc_pmx_functions[] = { SIRFSOC_PMX_FUNCTION("uart2", uart2grp, uart2_padmux), SIRFSOC_PMX_FUNCTION("uart2_nostreamctrl", uart2_nostreamctrlgrp, uart2_nostreamctrl_padmux), SIRFSOC_PMX_FUNCTION("usp0", usp0grp, usp0_padmux), + SIRFSOC_PMX_FUNCTION("usp0_uart_nostreamctrl", + usp0_uart_nostreamctrl_grp, + usp0_uart_nostreamctrl_padmux), SIRFSOC_PMX_FUNCTION("usp1", usp1grp, usp1_padmux), SIRFSOC_PMX_FUNCTION("i2c0", i2c0grp, i2c0_padmux), SIRFSOC_PMX_FUNCTION("i2c1", i2c1grp, i2c1_padmux), -- cgit v1.2.3-70-g09d2 From c8078de853d51e9b86a2f025ee281b5a81c80655 Mon Sep 17 00:00:00 2001 From: Barry Song Date: Thu, 4 Jul 2013 15:55:27 +0800 Subject: arm/dts: sirf: fix the pingroup name mismatch between drivers and dts in drivers/pinctrl/sirf, pingroup name is cko0 and cko1, but in dts, they are cko0 and cko1_rst. this patch fixes the error in dts. Signed-off-by: Barry Song Signed-off-by: Linus Walleij --- arch/arm/boot/dts/atlas6.dtsi | 16 ++++++++-------- arch/arm/boot/dts/prima2.dtsi | 16 ++++++++-------- 2 files changed, 16 insertions(+), 16 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/atlas6.dtsi b/arch/arm/boot/dts/atlas6.dtsi index 537041253db7..a0f2721ea583 100644 --- a/arch/arm/boot/dts/atlas6.dtsi +++ b/arch/arm/boot/dts/atlas6.dtsi @@ -521,16 +521,16 @@ sirf,function = "pulse_count"; }; }; - cko0_rst_pins_a: cko0_rst@0 { - cko0_rst { - sirf,pins = "cko0_rstgrp"; - sirf,function = "cko0_rst"; + cko0_pins_a: cko0@0 { + cko0 { + sirf,pins = "cko0grp"; + sirf,function = "cko0"; }; }; - cko1_rst_pins_a: cko1_rst@0 { - cko1_rst { - sirf,pins = "cko1_rstgrp"; - sirf,function = "cko1_rst"; + cko1_pins_a: cko1@0 { + cko1 { + sirf,pins = "cko1grp"; + sirf,function = "cko1"; }; }; }; diff --git a/arch/arm/boot/dts/prima2.dtsi b/arch/arm/boot/dts/prima2.dtsi index 05e9489cf95c..bbeb623fc2c6 100644 --- a/arch/arm/boot/dts/prima2.dtsi +++ b/arch/arm/boot/dts/prima2.dtsi @@ -515,16 +515,16 @@ sirf,function = "pulse_count"; }; }; - cko0_rst_pins_a: cko0_rst@0 { - cko0_rst { - sirf,pins = "cko0_rstgrp"; - sirf,function = "cko0_rst"; + cko0_pins_a: cko0@0 { + cko0 { + sirf,pins = "cko0grp"; + sirf,function = "cko0"; }; }; - cko1_rst_pins_a: cko1_rst@0 { - cko1_rst { - sirf,pins = "cko1_rstgrp"; - sirf,function = "cko1_rst"; + cko1_pins_a: cko1@0 { + cko1 { + sirf,pins = "cko1grp"; + sirf,function = "cko1"; }; }; }; -- cgit v1.2.3-70-g09d2 From 334ab91d5818256befbf083755d0bb9e7dbd2325 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Tue, 9 Jul 2013 08:26:24 +0100 Subject: ARM: dts: STi: Fix pinconf setup for STiH416 serial2 This patch fixes a bug in pinctrl setup of serial2 device, Some of the pins in the pinctrl node of serial2 do not belong to that pin-controller. This patch divides them in the pins into there respective pin controller nodes. Without this patch serial on StiH416-B2000 Board will not work as it fails with: "st-pinctrl pin-controller-rear.3: failed to get pin(99) name st-pinctrl pin-controller-rear.3: maps: function serial2 group serial2-0 num 4 pinconfig core: failed to register map default (3): no group/pin given" Signed-off-by: Srinivas Kandagatla Signed-off-by: Olof Johansson --- arch/arm/boot/dts/stih416-pinctrl.dtsi | 10 +++++++++- arch/arm/boot/dts/stih416.dtsi | 2 +- 2 files changed, 10 insertions(+), 2 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi index 957b21a71b4b..0f246c979262 100644 --- a/arch/arm/boot/dts/stih416-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi @@ -166,6 +166,15 @@ reg = <0x9000 0x100>; st,bank-name = "PIO31"; }; + + serial2-oe { + pinctrl_serial2_oe: serial2-1 { + st,pins { + output-enable = <&PIO11 3 ALT2 OUT>; + }; + }; + }; + }; pin-controller-rear { @@ -218,7 +227,6 @@ st,pins { tx = <&PIO17 4 ALT2 OUT>; rx = <&PIO17 5 ALT2 IN>; - output-enable = <&PIO11 3 ALT2 OUT>; }; }; }; diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi index 3cecd9689a49..1a0326ea7d07 100644 --- a/arch/arm/boot/dts/stih416.dtsi +++ b/arch/arm/boot/dts/stih416.dtsi @@ -79,7 +79,7 @@ interrupts = <0 197 0>; clocks = <&CLK_S_ICN_REG_0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_serial2>; + pinctrl-0 = <&pinctrl_serial2 &pinctrl_serial2_oe>; }; /* SBC_UART1 */ -- cgit v1.2.3-70-g09d2 From 3709d323085853dc537711154004ba8704cefb9c Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Mon, 29 Jul 2013 12:03:01 -0500 Subject: ARM: dts: omap5-uevm: document regulator signals used on the actual board MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, currently we use the Palmas regulator names which is used for different purposes on uEVM. Document the same based on 750-2628-XXX boards - which is meant to be supported by this dts. Reported-by: Marc Jüttner Signed-off-by: Nishanth Menon Acked-by: J Keerthy Acked-by: Benoit Cousson Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 08b72678abff..b430b8f884b8 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -282,6 +282,7 @@ regulators { smps123_reg: smps123 { + /* VDD_OPP_MPU */ regulator-name = "smps123"; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; @@ -290,6 +291,7 @@ }; smps45_reg: smps45 { + /* VDD_OPP_MM */ regulator-name = "smps45"; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1310000>; @@ -298,6 +300,7 @@ }; smps6_reg: smps6 { + /* VDD_DDR3 - over VDD_SMPS6 */ regulator-name = "smps6"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; @@ -306,6 +309,7 @@ }; smps7_reg: smps7 { + /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ regulator-name = "smps7"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -314,6 +318,7 @@ }; smps8_reg: smps8 { + /* VDD_OPP_CORE */ regulator-name = "smps8"; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1310000>; @@ -322,6 +327,7 @@ }; smps9_reg: smps9 { + /* VDDA_2v1_AUD over VDD_2v1 */ regulator-name = "smps9"; regulator-min-microvolt = <2100000>; regulator-max-microvolt = <2100000>; @@ -331,6 +337,7 @@ }; smps10_reg: smps10 { + /* VBUS_5V_OTG */ regulator-name = "smps10"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -339,6 +346,7 @@ }; ldo1_reg: ldo1 { + /* VDDAPHY_CAM: vdda_csiport */ regulator-name = "ldo1"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; @@ -347,6 +355,7 @@ }; ldo2_reg: ldo2 { + /* VCC_2V8_DISP: Does not go anywhere */ regulator-name = "ldo2"; regulator-min-microvolt = <2900000>; regulator-max-microvolt = <2900000>; @@ -355,6 +364,7 @@ }; ldo3_reg: ldo3 { + /* VDDAPHY_MDM: vdda_lli */ regulator-name = "ldo3"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; @@ -363,6 +373,7 @@ }; ldo4_reg: ldo4 { + /* VDDAPHY_DISP: vdda_dsiport/hdmi */ regulator-name = "ldo4"; regulator-min-microvolt = <2200000>; regulator-max-microvolt = <2200000>; @@ -371,6 +382,7 @@ }; ldo5_reg: ldo5 { + /* VDDA_1V8_PHY: usb/sata/hdmi.. */ regulator-name = "ldo5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -379,6 +391,7 @@ }; ldo6_reg: ldo6 { + /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ regulator-name = "ldo6"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; @@ -387,6 +400,7 @@ }; ldo7_reg: ldo7 { + /* VDD_VPP: vpp1 */ regulator-name = "ldo7"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; @@ -395,6 +409,7 @@ }; ldo8_reg: ldo8 { + /* VDD_3v0: Does not go anywhere */ regulator-name = "ldo8"; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1500000>; @@ -403,6 +418,7 @@ }; ldo9_reg: ldo9 { + /* VCC_DV_SDIO: vdds_sdcard */ regulator-name = "ldo9"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; @@ -411,6 +427,7 @@ }; ldoln_reg: ldoln { + /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ regulator-name = "ldoln"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -419,6 +436,7 @@ }; ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ regulator-name = "ldousb"; regulator-min-microvolt = <3250000>; regulator-max-microvolt = <3250000>; -- cgit v1.2.3-70-g09d2 From e18235a62a7ea737d0a3f73c76eacaaec6df3dfe Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Mon, 29 Jul 2013 12:03:02 -0500 Subject: ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, The regulator information is based on an older temporary pre-production board variant and does not reflect production board 750-2628-XXX boards. The following fixes are hence mandatory to ensure right voltage is supplied to key OMAP5 SoC voltage rails: - LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This can only be supplied at 1.5V or 1.8V and we currently supply 2.8V. To prevent any potential device damage risk, use the specified 1.5V-1.8V supply. Remove 'always-on' and 'boot-on' settings here as it is a 'on need' supply to SoC IP and is not enabled by PMIC by default at boot. - LDO3 supplies Low Latency Interface(LLI) hardware module which is a special hardware to communicate with Modem. However since uEVM is not setup by default for this communication, this should be disabled by default. Further, vdda_lli is supposed to be 1.5V and not 3V. - LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi This can only be supplied at 1.5V or 1.8V and we currently supply 2.2V. To prevent any potential device damage risk, use the specified 1.5V-1.8V supply. Remove 'always-on' and 'boot-on' settings here as it is a 'on need' supply to SoC IP and is not enabled by PMIC by default at boot. - LDO6 supplies the board specified VDDS_1V2_WKUP supply going to ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply 1.2V instead of 1.5V. - LDO7 supplies VDD_VPP which is vpp1. This is currently configured for 1.5V which as per data manual "A pulse width of 1000 ns and an amplitude of 2V is required to program each eFuse bit. Otherwise, VPP1 must not be supplied". So, fix the voltage to 2V. and disable the supply since we have no plans of programming efuse bits - it can only be done once - in factory. Further it is not enabled by default by PMIC so, 'boot-on' must be removed, and the 'always-on' needs to be removed to achieve pulsing if efuse needs to be programmed. - LDO9 supplies the board specified vdds_sdcard supply going within SoC specification of 1.8V or 3.0V. Further the supply is controlled by switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled on need basis. Reported-by: Marc Jüttner Signed-off-by: Nishanth Menon Acked-by: J Keerthy Acked-by: Benoit Cousson Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 43 +++++++++++++++++++++------------------- 1 file changed, 23 insertions(+), 20 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index b430b8f884b8..247c03c0d734 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -235,7 +235,7 @@ }; &mmc1 { - vmmc-supply = <&vmmcsd_fixed>; + vmmc-supply = <&ldo9_reg>; bus-width = <4>; }; @@ -348,10 +348,8 @@ ldo1_reg: ldo1 { /* VDDAPHY_CAM: vdda_csiport */ regulator-name = "ldo1"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; }; ldo2_reg: ldo2 { @@ -366,19 +364,18 @@ ldo3_reg: ldo3 { /* VDDAPHY_MDM: vdda_lli */ regulator-name = "ldo3"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; regulator-boot-on; + /* Only if Modem is used */ + status = "disabled"; }; ldo4_reg: ldo4 { /* VDDAPHY_DISP: vdda_dsiport/hdmi */ regulator-name = "ldo4"; - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; }; ldo5_reg: ldo5 { @@ -393,8 +390,8 @@ ldo6_reg: ldo6 { /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ regulator-name = "ldo6"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; }; @@ -402,10 +399,10 @@ ldo7_reg: ldo7 { /* VDD_VPP: vpp1 */ regulator-name = "ldo7"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + /* Only for efuse reprograming! */ + status = "disabled"; }; ldo8_reg: ldo8 { @@ -421,8 +418,7 @@ /* VCC_DV_SDIO: vdds_sdcard */ regulator-name = "ldo9"; regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; + regulator-max-microvolt = <3000000>; regulator-boot-on; }; @@ -443,6 +439,13 @@ regulator-always-on; regulator-boot-on; }; + + regen3_reg: regen3 { + /* REGEN3 controls LDO9 supply to card */ + regulator-name = "regen3"; + regulator-always-on; + regulator-boot-on; + }; }; }; }; -- cgit v1.2.3-70-g09d2 From bd3c5544a1e98a25d2d24c98779092e0f84373f7 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Mon, 29 Jul 2013 12:03:03 -0500 Subject: ARM: dts: omap5-uevm: update optional/unused regulator configurations MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, The regulator information is based on an older temporary pre-production board variant and does not reflect production board 750-2628-XXX boards. The following optional/unused regulators can be updated: - SMPS9 supplies TWL6040 over VDDA_2v1_AUD. This regulator needs to be enabled only when audio is active. Since it does not come active by default, it does not require "always-on" or "boot-on". - LDO2 and LDO8 do not go to any peripheral or connector on the board. Further, these unused regulators should have been 2.8V for LDO2 and 3.0V for LDO8. Mark these LDOs as disabled in the dts until needed. Reported-by: Marc Jüttner Signed-off-by: Nishanth Menon Acked-by: J Keerthy Acked-by: Benoit Cousson Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 247c03c0d734..65d7b601651c 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -331,8 +331,6 @@ regulator-name = "smps9"; regulator-min-microvolt = <2100000>; regulator-max-microvolt = <2100000>; - regulator-always-on; - regulator-boot-on; ti,smps-range = <0x80>; }; @@ -355,10 +353,10 @@ ldo2_reg: ldo2 { /* VCC_2V8_DISP: Does not go anywhere */ regulator-name = "ldo2"; - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - regulator-always-on; - regulator-boot-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + /* Unused */ + status = "disabled"; }; ldo3_reg: ldo3 { @@ -408,10 +406,11 @@ ldo8_reg: ldo8 { /* VDD_3v0: Does not go anywhere */ regulator-name = "ldo8"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; regulator-boot-on; + /* Unused */ + status = "disabled"; }; ldo9_reg: ldo9 { -- cgit v1.2.3-70-g09d2 From 95e8ce69a043bc501b45508cc31f1dc9a3f64d3e Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Thu, 1 Aug 2013 13:13:31 +0100 Subject: ARM: STi: Fix cpu nodes with correct device_type. This patch fixes cpu nodes with device_type = "cpu". This change was not necessary before 3.10-rc7. Without this patch STi SOCs does not boot as SMP. Signed-off-by: Srinivas Kandagatla Signed-off-by: Olof Johansson --- arch/arm/boot/dts/stih41x.dtsi | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/stih41x.dtsi b/arch/arm/boot/dts/stih41x.dtsi index 7321403cab8a..f5b9898d9c6e 100644 --- a/arch/arm/boot/dts/stih41x.dtsi +++ b/arch/arm/boot/dts/stih41x.dtsi @@ -6,10 +6,12 @@ #address-cells = <1>; #size-cells = <0>; cpu@0 { + device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; }; cpu@1 { + device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; }; -- cgit v1.2.3-70-g09d2 From a1632ad35c37a8bd7bd22dd601906bfef90ad3a6 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Tue, 23 Jul 2013 11:11:45 -0700 Subject: ARM: tegra: enable ULPI phy on Colibri T20 This was missed when splitting out the phy from the controller node in commit 9dffe3be3f32 (ARM: tegra: modify ULPI reset GPIO properties). Signed-off-by: Lucas Stach Signed-off-by: Stephen Warren Signed-off-by: Olof Johansson --- arch/arm/boot/dts/tegra20-colibri-512.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/boot') diff --git a/arch/arm/boot/dts/tegra20-colibri-512.dtsi b/arch/arm/boot/dts/tegra20-colibri-512.dtsi index 2fcb3f2ca160..5592be6f2f7a 100644 --- a/arch/arm/boot/dts/tegra20-colibri-512.dtsi +++ b/arch/arm/boot/dts/tegra20-colibri-512.dtsi @@ -457,6 +457,7 @@ }; usb-phy@c5004000 { + status = "okay"; nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>; }; -- cgit v1.2.3-70-g09d2