From 0aa6770000bafa65c17cf44b6619d328d4fc79b3 Mon Sep 17 00:00:00 2001 From: Philip Rakity Date: Sun, 27 May 2012 18:36:33 -0700 Subject: mmc: sdhci: only set 200mA support for 1.8v if 200mA is available max_current_caps can return 0 if not available from the sd controller. If no regulator is present or the regulator specifies a current less then 200ma, we no longer still set the 200mA caps bit anyway. Signed-off-by: Philip Rakity Reviewed-by: Aaron Lu Signed-off-by: Chris Ball --- drivers/mmc/core/sd.c | 23 ++++++++++++----------- 1 file changed, 12 insertions(+), 11 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index b2b43f624b9e..b0b9e372f5da 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -553,13 +553,13 @@ static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status) static int sd_set_current_limit(struct mmc_card *card, u8 *status) { - int current_limit = 0; + int current_limit = SD_SET_CURRENT_NO_CHANGE; int err; /* * Current limit switch is only defined for SDR50, SDR104, and DDR50 - * bus speed modes. For other bus speed modes, we set the default - * current limit of 200mA. + * bus speed modes. For other bus speed modes, we do not change the + * current limit. */ if ((card->sd_bus_speed == UHS_SDR50_BUS_SPEED) || (card->sd_bus_speed == UHS_SDR104_BUS_SPEED) || @@ -595,17 +595,18 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status) if (card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_200) current_limit = SD_SET_CURRENT_LIMIT_200; } - } else - current_limit = SD_SET_CURRENT_LIMIT_200; + } - err = mmc_sd_switch(card, 1, 3, current_limit, status); - if (err) - return err; + if (current_limit != SD_SET_CURRENT_NO_CHANGE) { + err = mmc_sd_switch(card, 1, 3, current_limit, status); + if (err) + return err; - if (((status[15] >> 4) & 0x0F) != current_limit) - pr_warning("%s: Problem setting current limit!\n", - mmc_hostname(card->host)); + if (((status[15] >> 4) & 0x0F) != current_limit) + pr_warning("%s: Problem setting current limit!\n", + mmc_hostname(card->host)); + } return 0; } -- cgit v1.2.3-70-g09d2 From b63b5e819d5b21ae493c17c356018ffa98d3ee1c Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 2 Jul 2012 18:55:13 +0100 Subject: mmc: core: correct invalid error checking The effect of the existing code is that we continue blindly when we should warn about an invalid allocation unit. Reported-by: dcb314@hotmail.com Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44061 Signed-off-by: Alan Cox Signed-off-by: Chris Ball --- drivers/mmc/core/sd.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index b0b9e372f5da..33c6f26c68d0 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -244,7 +244,7 @@ static int mmc_read_ssr(struct mmc_card *card) * bitfield positions accordingly. */ au = UNSTUFF_BITS(ssr, 428 - 384, 4); - if (au > 0 || au <= 9) { + if (au > 0 && au <= 9) { card->ssr.au = 1 << (au + 4); es = UNSTUFF_BITS(ssr, 408 - 384, 16); et = UNSTUFF_BITS(ssr, 402 - 384, 6); -- cgit v1.2.3-70-g09d2 From a39ca6ae0a08994a59d017a445939e164bc77fd5 Mon Sep 17 00:00:00 2001 From: Aaron Lu Date: Tue, 3 Jul 2012 14:16:11 +0800 Subject: mmc: core: Simplify and fix for SD switch processing In mmc_read_switch, just do a one time mode 0 switch command to get the support bits information, no need to do multiple times as the support bits do not change with different arguments. And no need to check current limit support bits, as these bits are fixed according to the signal voltage. If the signal voltage is 1.8V, the support bits would be 0xf and if the signal voltage is 3.3V, the support bits would be 0x01. We will check host's ability to set the current limit. Signed-off-by: Aaron Lu Signed-off-by: Chris Ball --- drivers/mmc/core/sd.c | 94 ++++++++++++--------------------------------------- 1 file changed, 22 insertions(+), 72 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 33c6f26c68d0..8460568e5213 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -290,8 +290,12 @@ static int mmc_read_switch(struct mmc_card *card) return -ENOMEM; } - /* Find out the supported Bus Speed Modes. */ - err = mmc_sd_switch(card, 0, 0, 1, status); + /* + * Find out the card's support bits with a mode 0 operation. + * The argument does not matter, as the support bits do not + * change with the arguments. + */ + err = mmc_sd_switch(card, 0, 0, 0, status); if (err) { /* * If the host or the card can't do the switch, @@ -312,46 +316,8 @@ static int mmc_read_switch(struct mmc_card *card) if (card->scr.sda_spec3) { card->sw_caps.sd3_bus_mode = status[13]; - - /* Find out Driver Strengths supported by the card */ - err = mmc_sd_switch(card, 0, 2, 1, status); - if (err) { - /* - * If the host or the card can't do the switch, - * fail more gracefully. - */ - if (err != -EINVAL && err != -ENOSYS && err != -EFAULT) - goto out; - - pr_warning("%s: problem reading " - "Driver Strength.\n", - mmc_hostname(card->host)); - err = 0; - - goto out; - } - + /* Driver Strengths supported by the card */ card->sw_caps.sd3_drv_type = status[9]; - - /* Find out Current Limits supported by the card */ - err = mmc_sd_switch(card, 0, 3, 1, status); - if (err) { - /* - * If the host or the card can't do the switch, - * fail more gracefully. - */ - if (err != -EINVAL && err != -ENOSYS && err != -EFAULT) - goto out; - - pr_warning("%s: problem reading " - "Current Limit.\n", - mmc_hostname(card->host)); - err = 0; - - goto out; - } - - card->sw_caps.sd3_curr_limit = status[7]; } out: @@ -560,41 +526,24 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status) * Current limit switch is only defined for SDR50, SDR104, and DDR50 * bus speed modes. For other bus speed modes, we do not change the * current limit. + * We only check host's capability here, if we set a limit that is + * higher than the card's maximum current, the card will be using its + * maximum current, e.g. if the card's maximum current is 300ma, and + * when we set current limit to 200ma, the card will draw 200ma, and + * when we set current limit to 400/600/800ma, the card will draw its + * maximum 300ma from the host. */ if ((card->sd_bus_speed == UHS_SDR50_BUS_SPEED) || (card->sd_bus_speed == UHS_SDR104_BUS_SPEED) || (card->sd_bus_speed == UHS_DDR50_BUS_SPEED)) { - if (card->host->caps & MMC_CAP_MAX_CURRENT_800) { - if (card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_800) - current_limit = SD_SET_CURRENT_LIMIT_800; - else if (card->sw_caps.sd3_curr_limit & - SD_MAX_CURRENT_600) - current_limit = SD_SET_CURRENT_LIMIT_600; - else if (card->sw_caps.sd3_curr_limit & - SD_MAX_CURRENT_400) - current_limit = SD_SET_CURRENT_LIMIT_400; - else if (card->sw_caps.sd3_curr_limit & - SD_MAX_CURRENT_200) - current_limit = SD_SET_CURRENT_LIMIT_200; - } else if (card->host->caps & MMC_CAP_MAX_CURRENT_600) { - if (card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_600) - current_limit = SD_SET_CURRENT_LIMIT_600; - else if (card->sw_caps.sd3_curr_limit & - SD_MAX_CURRENT_400) - current_limit = SD_SET_CURRENT_LIMIT_400; - else if (card->sw_caps.sd3_curr_limit & - SD_MAX_CURRENT_200) - current_limit = SD_SET_CURRENT_LIMIT_200; - } else if (card->host->caps & MMC_CAP_MAX_CURRENT_400) { - if (card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_400) - current_limit = SD_SET_CURRENT_LIMIT_400; - else if (card->sw_caps.sd3_curr_limit & - SD_MAX_CURRENT_200) - current_limit = SD_SET_CURRENT_LIMIT_200; - } else if (card->host->caps & MMC_CAP_MAX_CURRENT_200) { - if (card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_200) - current_limit = SD_SET_CURRENT_LIMIT_200; - } + if (card->host->caps & MMC_CAP_MAX_CURRENT_800) + current_limit = SD_SET_CURRENT_LIMIT_800; + else if (card->host->caps & MMC_CAP_MAX_CURRENT_600) + current_limit = SD_SET_CURRENT_LIMIT_600; + else if (card->host->caps & MMC_CAP_MAX_CURRENT_400) + current_limit = SD_SET_CURRENT_LIMIT_400; + else if (card->host->caps & MMC_CAP_MAX_CURRENT_200) + current_limit = SD_SET_CURRENT_LIMIT_200; } if (current_limit != SD_SET_CURRENT_NO_CHANGE) { @@ -607,6 +556,7 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status) mmc_hostname(card->host)); } + return 0; } -- cgit v1.2.3-70-g09d2 From 55c4665ea0a42fd6427826bfce96eb4b0389262a Mon Sep 17 00:00:00 2001 From: Aaron Lu Date: Wed, 4 Jul 2012 13:31:48 +0800 Subject: mmc: sd: Fix sd current limit setting Host has different current capabilities at different voltages, we need to record these settings seperately. The defined voltages are 1.8/3.0/3.3. For other voltages, we do not touch current limit setting. Before we set the current limit for the sd card, find out the host's operating voltage first and then find out the current capabilities of the host at that voltage to set the current limit. Signed-off-by: Aaron Lu Reviewed-by: Philip Rakity Signed-off-by: Chris Ball --- drivers/mmc/core/sd.c | 69 +++++++++++++++++++++++++++++++++++++----------- drivers/mmc/host/sdhci.c | 31 +++------------------- include/linux/mmc/host.h | 10 +++---- 3 files changed, 60 insertions(+), 50 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 8460568e5213..441bdf472c99 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -517,15 +517,54 @@ static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status) return 0; } +/* Get host's max current setting at its current voltage */ +static u32 sd_get_host_max_current(struct mmc_host *host) +{ + u32 voltage, max_current; + + voltage = 1 << host->ios.vdd; + switch (voltage) { + case MMC_VDD_165_195: + max_current = host->max_current_180; + break; + case MMC_VDD_29_30: + case MMC_VDD_30_31: + max_current = host->max_current_300; + break; + case MMC_VDD_32_33: + case MMC_VDD_33_34: + max_current = host->max_current_330; + break; + default: + max_current = 0; + } + + return max_current; +} + static int sd_set_current_limit(struct mmc_card *card, u8 *status) { int current_limit = SD_SET_CURRENT_NO_CHANGE; int err; + u32 max_current; /* * Current limit switch is only defined for SDR50, SDR104, and DDR50 * bus speed modes. For other bus speed modes, we do not change the * current limit. + */ + if ((card->sd_bus_speed != UHS_SDR50_BUS_SPEED) && + (card->sd_bus_speed != UHS_SDR104_BUS_SPEED) && + (card->sd_bus_speed != UHS_DDR50_BUS_SPEED)) + return 0; + + /* + * Host has different current capabilities when operating at + * different voltages, so find out its max current first. + */ + max_current = sd_get_host_max_current(card->host); + + /* * We only check host's capability here, if we set a limit that is * higher than the card's maximum current, the card will be using its * maximum current, e.g. if the card's maximum current is 300ma, and @@ -533,18 +572,14 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status) * when we set current limit to 400/600/800ma, the card will draw its * maximum 300ma from the host. */ - if ((card->sd_bus_speed == UHS_SDR50_BUS_SPEED) || - (card->sd_bus_speed == UHS_SDR104_BUS_SPEED) || - (card->sd_bus_speed == UHS_DDR50_BUS_SPEED)) { - if (card->host->caps & MMC_CAP_MAX_CURRENT_800) - current_limit = SD_SET_CURRENT_LIMIT_800; - else if (card->host->caps & MMC_CAP_MAX_CURRENT_600) - current_limit = SD_SET_CURRENT_LIMIT_600; - else if (card->host->caps & MMC_CAP_MAX_CURRENT_400) - current_limit = SD_SET_CURRENT_LIMIT_400; - else if (card->host->caps & MMC_CAP_MAX_CURRENT_200) - current_limit = SD_SET_CURRENT_LIMIT_200; - } + if (max_current >= 800) + current_limit = SD_SET_CURRENT_LIMIT_800; + else if (max_current >= 600) + current_limit = SD_SET_CURRENT_LIMIT_600; + else if (max_current >= 400) + current_limit = SD_SET_CURRENT_LIMIT_400; + else if (max_current >= 200) + current_limit = SD_SET_CURRENT_LIMIT_200; if (current_limit != SD_SET_CURRENT_NO_CHANGE) { err = mmc_sd_switch(card, 1, 3, current_limit, status); @@ -677,6 +712,7 @@ struct device_type sd_type = { int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr) { int err; + u32 max_current; /* * Since we're changing the OCR value, we seem to @@ -704,9 +740,12 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr) MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50)) ocr |= SD_OCR_S18R; - /* If the host can supply more than 150mA, XPC should be set to 1. */ - if (host->caps & (MMC_CAP_SET_XPC_330 | MMC_CAP_SET_XPC_300 | - MMC_CAP_SET_XPC_180)) + /* + * If the host can supply more than 150mA at current voltage, + * XPC should be set to 1. + */ + max_current = sd_get_host_max_current(host); + if (max_current > 150) ocr |= SD_OCR_XPC; try_again: diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index d9966568143b..9a11dc39921c 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -2906,53 +2906,28 @@ int sdhci_add_host(struct sdhci_host *host) } if (caps[0] & SDHCI_CAN_VDD_330) { - int max_current_330; - ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34; - max_current_330 = ((max_current_caps & + mmc->max_current_330 = ((max_current_caps & SDHCI_MAX_CURRENT_330_MASK) >> SDHCI_MAX_CURRENT_330_SHIFT) * SDHCI_MAX_CURRENT_MULTIPLIER; - - if (max_current_330 > 150) - mmc->caps |= MMC_CAP_SET_XPC_330; } if (caps[0] & SDHCI_CAN_VDD_300) { - int max_current_300; - ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31; - max_current_300 = ((max_current_caps & + mmc->max_current_300 = ((max_current_caps & SDHCI_MAX_CURRENT_300_MASK) >> SDHCI_MAX_CURRENT_300_SHIFT) * SDHCI_MAX_CURRENT_MULTIPLIER; - - if (max_current_300 > 150) - mmc->caps |= MMC_CAP_SET_XPC_300; } if (caps[0] & SDHCI_CAN_VDD_180) { - int max_current_180; - ocr_avail |= MMC_VDD_165_195; - max_current_180 = ((max_current_caps & + mmc->max_current_180 = ((max_current_caps & SDHCI_MAX_CURRENT_180_MASK) >> SDHCI_MAX_CURRENT_180_SHIFT) * SDHCI_MAX_CURRENT_MULTIPLIER; - - if (max_current_180 > 150) - mmc->caps |= MMC_CAP_SET_XPC_180; - - /* Maximum current capabilities of the host at 1.8V */ - if (max_current_180 >= 800) - mmc->caps |= MMC_CAP_MAX_CURRENT_800; - else if (max_current_180 >= 600) - mmc->caps |= MMC_CAP_MAX_CURRENT_600; - else if (max_current_180 >= 400) - mmc->caps |= MMC_CAP_MAX_CURRENT_400; - else if (max_current_180 >= 200) - mmc->caps |= MMC_CAP_MAX_CURRENT_200; } mmc->ocr_avail = ocr_avail; diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 65c64ee578a7..f578a71d82a6 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -189,6 +189,9 @@ struct mmc_host { u32 ocr_avail_sd; /* SD-specific OCR */ u32 ocr_avail_mmc; /* MMC-specific OCR */ struct notifier_block pm_notify; + u32 max_current_330; + u32 max_current_300; + u32 max_current_180; #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */ #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */ @@ -232,16 +235,9 @@ struct mmc_host { #define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */ #define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */ #define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */ -#define MMC_CAP_SET_XPC_330 (1 << 20) /* Host supports >150mA current at 3.3V */ -#define MMC_CAP_SET_XPC_300 (1 << 21) /* Host supports >150mA current at 3.0V */ -#define MMC_CAP_SET_XPC_180 (1 << 22) /* Host supports >150mA current at 1.8V */ #define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */ #define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */ #define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */ -#define MMC_CAP_MAX_CURRENT_200 (1 << 26) /* Host max current limit is 200mA */ -#define MMC_CAP_MAX_CURRENT_400 (1 << 27) /* Host max current limit is 400mA */ -#define MMC_CAP_MAX_CURRENT_600 (1 << 28) /* Host max current limit is 600mA */ -#define MMC_CAP_MAX_CURRENT_800 (1 << 29) /* Host max current limit is 800mA */ #define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */ #define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */ -- cgit v1.2.3-70-g09d2 From 108ecc4cf9c46a4caabaf18efc42d19818c95b70 Mon Sep 17 00:00:00 2001 From: Aaron Lu Date: Tue, 10 Jul 2012 16:55:37 +0800 Subject: mmc: core: reset signal voltage on power up Add a call to mmc_set_signal_voltage() to set signal voltage to 3.3v in mmc_power_up so that we do not need to touch signal voltage setting in mmc/sd/sdio init functions and rescan function. For mmc/sd cards, when doing a suspend/resume cycle, consider the unsafe resume case, the card will lose its power and when powered on again, we will set signal voltage to 3.3v in mmc_power_up before its resume function gets called, which will re-init the card. And for sdio cards, when doing a suspend/resume cycle, consider the unsafe resume case, the card will either lose its power or not depending on if it wants to wakeup the host. If power is not maintained, it is the same case as mmc/sd cards. If power is maintained, mmc_power_up will not be called and the card's signal voltage will remain at the last setting. Signed-off-by: Aaron Lu Tested-by: Venkatraman S Signed-off-by: Chris Ball --- drivers/mmc/core/core.c | 6 +++--- drivers/mmc/core/mmc.c | 3 --- drivers/mmc/core/sd.c | 3 --- drivers/mmc/core/sdio.c | 7 ------- 4 files changed, 3 insertions(+), 16 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index 9503cabc96f1..8ac5246e2ab2 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1212,6 +1212,9 @@ static void mmc_power_up(struct mmc_host *host) host->ios.timing = MMC_TIMING_LEGACY; mmc_set_ios(host); + /* Set signal voltage to 3.3V */ + mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, false); + /* * This delay should be sufficient to allow the power supply * to reach the minimum voltage. @@ -1963,9 +1966,6 @@ static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq) */ mmc_hw_reset_for_init(host); - /* Initialization should be done at 3.3 V I/O voltage. */ - mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0); - /* * sdio_reset sends CMD52 to reset card. Since we do not know * if the card is being re-initialized, just send it. CMD52 diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c index 4f4489aa6bae..396b25891bb9 100644 --- a/drivers/mmc/core/mmc.c +++ b/drivers/mmc/core/mmc.c @@ -818,9 +818,6 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr, if (!mmc_host_is_spi(host)) mmc_set_bus_mode(host, MMC_BUSMODE_OPENDRAIN); - /* Initialization should be done at 3.3 V I/O voltage. */ - mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0); - /* * Since we're changing the OCR value, we seem to * need to tell some cards to go back to the idle diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 441bdf472c99..74972c241dff 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -901,9 +901,6 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr, BUG_ON(!host); WARN_ON(!host->claimed); - /* The initialization should be done at 3.3 V I/O voltage. */ - mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0); - err = mmc_sd_get_cid(host, ocr, cid, &rocr); if (err) return err; diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c index 41c5fd8848f4..d4619e2ec030 100644 --- a/drivers/mmc/core/sdio.c +++ b/drivers/mmc/core/sdio.c @@ -591,9 +591,6 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr, * Inform the card of the voltage */ if (!powered_resume) { - /* The initialization should be done at 3.3 V I/O voltage. */ - mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0); - err = mmc_send_io_op_cond(host, host->ocr, &ocr); if (err) goto err; @@ -1006,10 +1003,6 @@ static int mmc_sdio_power_restore(struct mmc_host *host) * restore the correct voltage setting of the card. */ - /* The initialization should be done at 3.3 V I/O voltage. */ - if (!mmc_card_keep_power(host)) - mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0); - sdio_reset(host); mmc_go_idle(host); mmc_send_if_cond(host, host->ocr_avail); -- cgit v1.2.3-70-g09d2