Merge tag 'gpio-omap-descriptors-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into soc/arm

This removes all usage of global GPIO numbers from
arch/arm/mach-omap[12].

The patches have been reviewed and tested by everyone
who showed interest which was one person that tested
on OSK1 and Nokia 770, and we smoked out the bugs and
also addressed all review comments.

Any remaining problems can certainly be fixed in-tree.

* tag 'gpio-omap-descriptors-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  ARM/musb: omap2: Remove global GPIO numbers from TUSB6010
  ARM: omap2: Rewrite WLAN quirk to use GPIO descriptors
  ARM: omap2: Get USB hub reset GPIO from descriptor
  ARM/gpio: Push OMAP2 quirk down into TWL4030 driver
  ARM: omap1: Exorcise the legacy GPIO header
  ARM: omap1: Make serial wakeup GPIOs use descriptors
  ARM: omap1: Fix up the Nokia 770 board device IRQs
  ARM/mmc: Convert old mmci-omap to GPIO descriptors
  Input: ads7846 - Convert to use software nodes
  ARM: omap1: Remove reliance on GPIO numbers from SX1
  ARM: omap1: Remove reliance on GPIO numbers from PalmTE
  ARM: omap1: Drop header on AMS Delta
  ARM/mfd/gpio: Fixup TPS65010 regression on OMAP1 OSK1

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

1 files changed, 44 insertions, 112 deletions

diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index 3353b0a923d9..564bf80a2621 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -10,7 +10,8 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
+#include <linux/gpio/consumer.h>
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/irq.h>
@@ -28,13 +29,12 @@
 
 #include "common.h"
 #include "mmc.h"
+#include "usb-tusb6010.h"
 #include "soc.h"
 #include "common-board-devices.h"
 
 #define TUSB6010_ASYNC_CS	1
 #define TUSB6010_SYNC_CS	4
-#define TUSB6010_GPIO_INT	58
-#define TUSB6010_GPIO_ENABLE	0
 #define TUSB6010_DMACHAN	0x3f
 
 #define NOKIA_N810_WIMAX	(1 << 2)
@@ -61,37 +61,6 @@ static void board_check_revision(void)
 }
 
 #if IS_ENABLED(CONFIG_USB_MUSB_TUSB6010)
-/*
- * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
- * 1.5 V voltage regulators of PM companion chip. Companion chip will then
- * provide then PGOOD signal to TUSB6010 which will release it from reset.
- */
-static int tusb_set_power(int state)
-{
-	int i, retval = 0;
-
-	if (state) {
-		gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
-		msleep(1);
-
-		/* Wait until TUSB6010 pulls INT pin down */
-		i = 100;
-		while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
-			msleep(1);
-			i--;
-		}
-
-		if (!i) {
-			printk(KERN_ERR "tusb: powerup failed\n");
-			retval = -ENODEV;
-		}
-	} else {
-		gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
-		msleep(10);
-	}
-
-	return retval;
-}
 
 static struct musb_hdrc_config musb_config = {
 	.multipoint	= 1,
@@ -102,39 +71,36 @@ static struct musb_hdrc_config musb_config = {
 
 static struct musb_hdrc_platform_data tusb_data = {
 	.mode		= MUSB_OTG,
-	.set_power	= tusb_set_power,
 	.min_power	= 25,	/* x2 = 50 mA drawn from VBUS as peripheral */
 	.power		= 100,	/* Max 100 mA VBUS for host mode */
 	.config		= &musb_config,
 };
 
+static struct gpiod_lookup_table tusb_gpio_table = {
+	.dev_id = "musb-tusb",
+	.table = {
+		GPIO_LOOKUP("gpio-0-15", 0, "enable",
+			    GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-48-63", 10, "int",
+			    GPIO_ACTIVE_HIGH),
+		{ }
+	},
+};
+
 static void __init n8x0_usb_init(void)
 {
 	int ret = 0;
-	static const char announce[] __initconst = KERN_INFO "TUSB 6010\n";
-
-	/* PM companion chip power control pin */
-	ret = gpio_request_one(TUSB6010_GPIO_ENABLE, GPIOF_OUT_INIT_LOW,
-			       "TUSB6010 enable");
-	if (ret != 0) {
-		printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
-		       TUSB6010_GPIO_ENABLE);
-		return;
-	}
-	tusb_set_power(0);
 
+	gpiod_add_lookup_table(&tusb_gpio_table);
 	ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
-					TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
-					TUSB6010_GPIO_INT, TUSB6010_DMACHAN);
+				       TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
+				       TUSB6010_DMACHAN);
 	if (ret != 0)
-		goto err;
+		return;
 
-	printk(announce);
+	pr_info("TUSB 6010\n");
 
 	return;
-
-err:
-	gpio_free(TUSB6010_GPIO_ENABLE);
 }
 #else
 
@@ -170,22 +136,32 @@ static struct spi_board_info n800_spi_board_info[] __initdata = {
  * GPIO23 and GPIO9		slot 2 EMMC on N810
  *
  */
-#define N8X0_SLOT_SWITCH_GPIO	96
-#define N810_EMMC_VSD_GPIO	23
-#define N810_EMMC_VIO_GPIO	9
-
 static int slot1_cover_open;
 static int slot2_cover_open;
 static struct device *mmc_device;
 
-static int n8x0_mmc_switch_slot(struct device *dev, int slot)
-{
-#ifdef CONFIG_MMC_DEBUG
-	dev_dbg(dev, "Choose slot %d\n", slot + 1);
-#endif
-	gpio_set_value(N8X0_SLOT_SWITCH_GPIO, slot);
-	return 0;
-}
+static struct gpiod_lookup_table nokia8xx_mmc_gpio_table = {
+	.dev_id = "mmci-omap.0",
+	.table = {
+		/* Slot switch, GPIO 96 */
+		GPIO_LOOKUP("gpio-80-111", 16,
+			    "switch", GPIO_ACTIVE_HIGH),
+		{ }
+	},
+};
+
+static struct gpiod_lookup_table nokia810_mmc_gpio_table = {
+	.dev_id = "mmci-omap.0",
+	.table = {
+		/* Slot index 1, VSD power, GPIO 23 */
+		GPIO_LOOKUP_IDX("gpio-16-31", 7,
+				"vsd", 1, GPIO_ACTIVE_HIGH),
+		/* Slot index 1, VIO power, GPIO 9 */
+		GPIO_LOOKUP_IDX("gpio-0-15", 9,
+				"vsd", 1, GPIO_ACTIVE_HIGH),
+		{ }
+	},
+};
 
 static int n8x0_mmc_set_power_menelaus(struct device *dev, int slot,
 					int power_on, int vdd)
@@ -256,31 +232,13 @@ static int n8x0_mmc_set_power_menelaus(struct device *dev, int slot,
 	return 0;
 }
 
-static void n810_set_power_emmc(struct device *dev,
-					 int power_on)
-{
-	dev_dbg(dev, "Set EMMC power %s\n", power_on ? "on" : "off");
-
-	if (power_on) {
-		gpio_set_value(N810_EMMC_VSD_GPIO, 1);
-		msleep(1);
-		gpio_set_value(N810_EMMC_VIO_GPIO, 1);
-		msleep(1);
-	} else {
-		gpio_set_value(N810_EMMC_VIO_GPIO, 0);
-		msleep(50);
-		gpio_set_value(N810_EMMC_VSD_GPIO, 0);
-		msleep(50);
-	}
-}
-
 static int n8x0_mmc_set_power(struct device *dev, int slot, int power_on,
 			      int vdd)
 {
 	if (board_is_n800() || slot == 0)
 		return n8x0_mmc_set_power_menelaus(dev, slot, power_on, vdd);
 
-	n810_set_power_emmc(dev, power_on);
+	/* The n810 power will be handled by GPIO code in the driver */
 
 	return 0;
 }
@@ -418,13 +376,6 @@ static void n8x0_mmc_shutdown(struct device *dev)
 static void n8x0_mmc_cleanup(struct device *dev)
 {
 	menelaus_unregister_mmc_callback();
-
-	gpio_free(N8X0_SLOT_SWITCH_GPIO);
-
-	if (board_is_n810()) {
-		gpio_free(N810_EMMC_VSD_GPIO);
-		gpio_free(N810_EMMC_VIO_GPIO);
-	}
 }
 
 /*
@@ -433,7 +384,6 @@ static void n8x0_mmc_cleanup(struct device *dev)
  */
 static struct omap_mmc_platform_data mmc1_data = {
 	.nr_slots			= 0,
-	.switch_slot			= n8x0_mmc_switch_slot,
 	.init				= n8x0_mmc_late_init,
 	.cleanup			= n8x0_mmc_cleanup,
 	.shutdown			= n8x0_mmc_shutdown,
@@ -463,14 +413,9 @@ static struct omap_mmc_platform_data mmc1_data = {
 
 static struct omap_mmc_platform_data *mmc_data[OMAP24XX_NR_MMC];
 
-static struct gpio n810_emmc_gpios[] __initdata = {
-	{ N810_EMMC_VSD_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vddf" },
-	{ N810_EMMC_VIO_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vdd"  },
-};
-
 static void __init n8x0_mmc_init(void)
 {
-	int err;
+	gpiod_add_lookup_table(&nokia8xx_mmc_gpio_table);
 
 	if (board_is_n810()) {
 		mmc1_data.slots[0].name = "external";
@@ -483,20 +428,7 @@ static void __init n8x0_mmc_init(void)
 		 */
 		mmc1_data.slots[1].name = "internal";
 		mmc1_data.slots[1].ban_openended = 1;
-	}
-
-	err = gpio_request_one(N8X0_SLOT_SWITCH_GPIO, GPIOF_OUT_INIT_LOW,
-			       "MMC slot switch");
-	if (err)
-		return;
-
-	if (board_is_n810()) {
-		err = gpio_request_array(n810_emmc_gpios,
-					 ARRAY_SIZE(n810_emmc_gpios));
-		if (err) {
-			gpio_free(N8X0_SLOT_SWITCH_GPIO);
-			return;
-		}
+		gpiod_add_lookup_table(&nokia810_mmc_gpio_table);
 	}
 
 	mmc1_data.nr_slots = 2;