Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

Pull PCI updates from Bjorn Helgaas:
 "Enumeration:

   - Rework portdrv shutdown so it disables interrupts but doesn't
     disable bus mastering, which leads to hangs on Loongson LS7A

   - Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
     again to avoid hardware issues on Loongson LS7A (and likely other
     devices based on DesignWare IP)

   - Ignore devices with a firmware (DT or ACPI) node that says the
     device is disabled

  Resource management:

   - Distribute spare resources to unconfigured hotplug bridges at
     boot-time (not just when hot-adding such a bridge), which makes
     hot-adding devices to docks work better. Tried this in v6.1 but had
     to revert for regressions, so try again

   - Fix root bus issue that dropped resources that happened to end
     at 0, e.g., [bus 00]

  PCI device hotplug:

   - Remove device locking when marking device as disconnected so this
     doesn't have to wait for concurrent driver bind/unbind to complete

   - Quirk more Qualcomm bridges that don't fully implement the PCIe
     Slot Status 'Command Completed' bit

  Power management:

   - Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
     don't miss hot-add notifications for USB4 docks, Thunderbolt, etc

  Reset:

   - Observe delay after reset, e.g., resuming from system sleep,
     regardless of whether a bridge can suspend to D3cold at runtime

   - Wait for secondary bus to become ready after a bridge reset

  Virtualization:

   - Avoid FLR on some AMD FCH AHCI adapters where it doesn't work

   - Allow independent IOMMU groups for some Wangxun NICs that prevent
     peer-to-peer transactions but don't advertise an ACS Capability

  Error handling:

   - Configure End-to-End-CRC (ECRC) only if Linux owns the AER
     Capability

   - Remove redundant Device Control Error Reporting Enable in the AER
     service driver since this is already done for all devices during
     enumeration

  ASPM:

   - Add pci_enable_link_state() interface to allow drivers to enable
     ASPM link state

  Endpoint framework:

   - Move dra7xx and tegra194 linkup processing from hard IRQ to
     threaded IRQ handler

   - Add a separate lock for endpoint controller list of endpoint
     function drivers to prevent deadlock in callbacks

   - Pass events from endpoint controller to endpoint function drivers
     via callbacks instead of notifiers

  Synopsys DesignWare eDMA controller driver (acked by Vinod):

   - Fix CPU vs PCI address issues

   - Fix source vs destination address issues

   - Fix issues with interleaved transfer semantics

   - Fix channel count initialization issue (issue still exists in
     several other drivers)

   - Clean up and improve debugfs usage so it will work on platforms
     with several eDMA devices

  Baikal T-1 PCIe controller driver:

   - Set a 64-bit DMA mask

  Freescale i.MX6 PCIe controller driver:

   - Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
     support

  Intel VMD host bridge driver:

   - Add quirk to configure PCIe ASPM and LTR. This is normally done by
     BIOS, and will be for future products

  Marvell MVEBU PCIe controller driver:

   - Mark this driver as broken in Kconfig since bugs prevent its daily
     usage

  MediaTek MT7621 PCIe controller driver:

   - Delay PHY port initialization to improve boot reliability for ZBT
     WE1326, ZBT WF3526-P, and some Netgear models

  Qualcomm PCIe controller driver:

   - Add MSM8998 DT compatible string

   - Unify MSM8996 and MSM8998 clock orderings

   - Add SM8350 DT binding and driver support

   - Add IPQ8074 Gen3 DT binding and driver support

   - Correct qcom,perst-regs in DT binding

   - Add qcom_pcie_host_deinit() so the PHY is powered off and
     regulators and clocks are disabled on late host-init errors

  Socionext UniPhier Pro5 controller driver:

   - Clean up uniphier-ep reg, clocks, resets, and their names in DT
     binding

  Synopsys DesignWare PCIe controller driver:

   - Restrict coherent DMA mask to 32 bits for MSI, but allow controller
     drivers to set 64-bit streaming DMA mask

   - Add eDMA engine support in both Root Port and Endpoint controllers

  Miscellaneous:

   - Remove MODULE_LICENSE from boolean drivers so they don't look like
     modules so modprobe can complain about them"

* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
  PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
  PCI: bt1: Set 64-bit DMA mask
  PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
  dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
  dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
  dmaengine: dw-edma: Add mem-mapped LL-entries support
  PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
  PCI: hv: Drop duplicate PCI_MSI dependency
  PCI/P2PDMA: Annotate RCU dereference
  PCI/sysfs: Constify struct kobj_type pci_slot_ktype
  PCI: hotplug: Allow marking devices as disconnected during bind/unbind
  PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
  PCI: qcom: Add IPQ8074 Gen3 port support
  dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
  dt-bindings: PCI: qcom: Sort compatibles alphabetically
  PCI: qcom: Fix host-init error handling
  PCI: qcom: Add SM8350 support
  dt-bindings: PCI: qcom: Add SM8350
  dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
  dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
  ...

1 files changed, 195 insertions, 0 deletions

diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 6d5d619ab2e9..53a16b8b6ac2 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -12,6 +12,7 @@
 #include <linux/bitops.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dma/edma.h>
 #include <linux/gpio/consumer.h>
 #include <linux/ioport.h>
 #include <linux/of.h>
@@ -142,6 +143,18 @@ int dw_pcie_get_resources(struct dw_pcie *pci)
 	if (!pci->atu_size)
 		pci->atu_size = SZ_4K;
 
+	/* eDMA region can be mapped to a custom base address */
+	if (!pci->edma.reg_base) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dma");
+		if (res) {
+			pci->edma.reg_base = devm_ioremap_resource(pci->dev, res);
+			if (IS_ERR(pci->edma.reg_base))
+				return PTR_ERR(pci->edma.reg_base);
+		} else if (pci->atu_size >= 2 * DEFAULT_DBI_DMA_OFFSET) {
+			pci->edma.reg_base = pci->atu_base + DEFAULT_DBI_DMA_OFFSET;
+		}
+	}
+
 	/* LLDD is supposed to manually switch the clocks and resets state */
 	if (dw_pcie_cap_is(pci, REQ_RES)) {
 		ret = dw_pcie_get_clocks(pci);
@@ -782,6 +795,188 @@ void dw_pcie_iatu_detect(struct dw_pcie *pci)
 		 pci->region_align / SZ_1K, (pci->region_limit + 1) / SZ_1G);
 }
 
+static u32 dw_pcie_readl_dma(struct dw_pcie *pci, u32 reg)
+{
+	u32 val = 0;
+	int ret;
+
+	if (pci->ops && pci->ops->read_dbi)
+		return pci->ops->read_dbi(pci, pci->edma.reg_base, reg, 4);
+
+	ret = dw_pcie_read(pci->edma.reg_base + reg, 4, &val);
+	if (ret)
+		dev_err(pci->dev, "Read DMA address failed\n");
+
+	return val;
+}
+
+static int dw_pcie_edma_irq_vector(struct device *dev, unsigned int nr)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	char name[6];
+	int ret;
+
+	if (nr >= EDMA_MAX_WR_CH + EDMA_MAX_RD_CH)
+		return -EINVAL;
+
+	ret = platform_get_irq_byname_optional(pdev, "dma");
+	if (ret > 0)
+		return ret;
+
+	snprintf(name, sizeof(name), "dma%u", nr);
+
+	return platform_get_irq_byname_optional(pdev, name);
+}
+
+static struct dw_edma_core_ops dw_pcie_edma_ops = {
+	.irq_vector = dw_pcie_edma_irq_vector,
+};
+
+static int dw_pcie_edma_find_chip(struct dw_pcie *pci)
+{
+	u32 val;
+
+	/*
+	 * Indirect eDMA CSRs access has been completely removed since v5.40a
+	 * thus no space is now reserved for the eDMA channels viewport and
+	 * former DMA CTRL register is no longer fixed to FFs.
+	 */
+	if (dw_pcie_ver_is_ge(pci, 540A))
+		val = 0xFFFFFFFF;
+	else
+		val = dw_pcie_readl_dbi(pci, PCIE_DMA_VIEWPORT_BASE + PCIE_DMA_CTRL);
+
+	if (val == 0xFFFFFFFF && pci->edma.reg_base) {
+		pci->edma.mf = EDMA_MF_EDMA_UNROLL;
+
+		val = dw_pcie_readl_dma(pci, PCIE_DMA_CTRL);
+	} else if (val != 0xFFFFFFFF) {
+		pci->edma.mf = EDMA_MF_EDMA_LEGACY;
+
+		pci->edma.reg_base = pci->dbi_base + PCIE_DMA_VIEWPORT_BASE;
+	} else {
+		return -ENODEV;
+	}
+
+	pci->edma.dev = pci->dev;
+
+	if (!pci->edma.ops)
+		pci->edma.ops = &dw_pcie_edma_ops;
+
+	pci->edma.flags |= DW_EDMA_CHIP_LOCAL;
+
+	pci->edma.ll_wr_cnt = FIELD_GET(PCIE_DMA_NUM_WR_CHAN, val);
+	pci->edma.ll_rd_cnt = FIELD_GET(PCIE_DMA_NUM_RD_CHAN, val);
+
+	/* Sanity check the channels count if the mapping was incorrect */
+	if (!pci->edma.ll_wr_cnt || pci->edma.ll_wr_cnt > EDMA_MAX_WR_CH ||
+	    !pci->edma.ll_rd_cnt || pci->edma.ll_rd_cnt > EDMA_MAX_RD_CH)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int dw_pcie_edma_irq_verify(struct dw_pcie *pci)
+{
+	struct platform_device *pdev = to_platform_device(pci->dev);
+	u16 ch_cnt = pci->edma.ll_wr_cnt + pci->edma.ll_rd_cnt;
+	char name[6];
+	int ret;
+
+	if (pci->edma.nr_irqs == 1)
+		return 0;
+	else if (pci->edma.nr_irqs > 1)
+		return pci->edma.nr_irqs != ch_cnt ? -EINVAL : 0;
+
+	ret = platform_get_irq_byname_optional(pdev, "dma");
+	if (ret > 0) {
+		pci->edma.nr_irqs = 1;
+		return 0;
+	}
+
+	for (; pci->edma.nr_irqs < ch_cnt; pci->edma.nr_irqs++) {
+		snprintf(name, sizeof(name), "dma%d", pci->edma.nr_irqs);
+
+		ret = platform_get_irq_byname_optional(pdev, name);
+		if (ret <= 0)
+			return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int dw_pcie_edma_ll_alloc(struct dw_pcie *pci)
+{
+	struct dw_edma_region *ll;
+	dma_addr_t paddr;
+	int i;
+
+	for (i = 0; i < pci->edma.ll_wr_cnt; i++) {
+		ll = &pci->edma.ll_region_wr[i];
+		ll->sz = DMA_LLP_MEM_SIZE;
+		ll->vaddr.mem = dmam_alloc_coherent(pci->dev, ll->sz,
+						    &paddr, GFP_KERNEL);
+		if (!ll->vaddr.mem)
+			return -ENOMEM;
+
+		ll->paddr = paddr;
+	}
+
+	for (i = 0; i < pci->edma.ll_rd_cnt; i++) {
+		ll = &pci->edma.ll_region_rd[i];
+		ll->sz = DMA_LLP_MEM_SIZE;
+		ll->vaddr.mem = dmam_alloc_coherent(pci->dev, ll->sz,
+						    &paddr, GFP_KERNEL);
+		if (!ll->vaddr.mem)
+			return -ENOMEM;
+
+		ll->paddr = paddr;
+	}
+
+	return 0;
+}
+
+int dw_pcie_edma_detect(struct dw_pcie *pci)
+{
+	int ret;
+
+	/* Don't fail if no eDMA was found (for the backward compatibility) */
+	ret = dw_pcie_edma_find_chip(pci);
+	if (ret)
+		return 0;
+
+	/* Don't fail on the IRQs verification (for the backward compatibility) */
+	ret = dw_pcie_edma_irq_verify(pci);
+	if (ret) {
+		dev_err(pci->dev, "Invalid eDMA IRQs found\n");
+		return 0;
+	}
+
+	ret = dw_pcie_edma_ll_alloc(pci);
+	if (ret) {
+		dev_err(pci->dev, "Couldn't allocate LLP memory\n");
+		return ret;
+	}
+
+	/* Don't fail if the DW eDMA driver can't find the device */
+	ret = dw_edma_probe(&pci->edma);
+	if (ret && ret != -ENODEV) {
+		dev_err(pci->dev, "Couldn't register eDMA device\n");
+		return ret;
+	}
+
+	dev_info(pci->dev, "eDMA: unroll %s, %hu wr, %hu rd\n",
+		 pci->edma.mf == EDMA_MF_EDMA_UNROLL ? "T" : "F",
+		 pci->edma.ll_wr_cnt, pci->edma.ll_rd_cnt);
+
+	return 0;
+}
+
+void dw_pcie_edma_remove(struct dw_pcie *pci)
+{
+	dw_edma_remove(&pci->edma);
+}
+
 void dw_pcie_setup(struct dw_pcie *pci)
 {
 	u32 val;