soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h

Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.

Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 482 insertions, 0 deletions

diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
new file mode 100644
index 000000000000..400213daa461
--- /dev/null
+++ b/include/linux/soc/qcom/geni-se.h
@@ -0,0 +1,482 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _LINUX_QCOM_GENI_SE
+#define _LINUX_QCOM_GENI_SE
+
+#include <linux/interconnect.h>
+
+/**
+ * enum geni_se_xfer_mode: Transfer modes supported by Serial Engines
+ *
+ * @GENI_SE_INVALID: Invalid mode
+ * @GENI_SE_FIFO: FIFO mode. Data is transferred with SE FIFO
+ * by programmed IO method
+ * @GENI_SE_DMA: Serial Engine DMA mode. Data is transferred
+ * with SE by DMAengine internal to SE
+ * @GENI_GPI_DMA: GPI DMA mode. Data is transferred using a DMAengine
+ * configured by a firmware residing on a GSI engine. This DMA name is
+ * interchangeably used as GSI or GPI which seem to imply the same DMAengine
+ */
+
+enum geni_se_xfer_mode {
+	GENI_SE_INVALID,
+	GENI_SE_FIFO,
+	GENI_SE_DMA,
+	GENI_GPI_DMA,
+};
+
+/* Protocols supported by GENI Serial Engines */
+enum geni_se_protocol_type {
+	GENI_SE_NONE,
+	GENI_SE_SPI,
+	GENI_SE_UART,
+	GENI_SE_I2C,
+	GENI_SE_I3C,
+};
+
+struct geni_wrapper;
+struct clk;
+
+enum geni_icc_path_index {
+	GENI_TO_CORE,
+	CPU_TO_GENI,
+	GENI_TO_DDR
+};
+
+struct geni_icc_path {
+	struct icc_path *path;
+	unsigned int avg_bw;
+};
+
+/**
+ * struct geni_se - GENI Serial Engine
+ * @base:		Base Address of the Serial Engine's register block
+ * @dev:		Pointer to the Serial Engine device
+ * @wrapper:		Pointer to the parent QUP Wrapper core
+ * @clk:		Handle to the core serial engine clock
+ * @num_clk_levels:	Number of valid clock levels in clk_perf_tbl
+ * @clk_perf_tbl:	Table of clock frequency input to serial engine clock
+ * @icc_paths:		Array of ICC paths for SE
+ */
+struct geni_se {
+	void __iomem *base;
+	struct device *dev;
+	struct geni_wrapper *wrapper;
+	struct clk *clk;
+	unsigned int num_clk_levels;
+	unsigned long *clk_perf_tbl;
+	struct geni_icc_path icc_paths[3];
+};
+
+/* Common SE registers */
+#define GENI_FORCE_DEFAULT_REG		0x20
+#define SE_GENI_STATUS			0x40
+#define GENI_SER_M_CLK_CFG		0x48
+#define GENI_SER_S_CLK_CFG		0x4c
+#define GENI_IF_DISABLE_RO		0x64
+#define GENI_FW_REVISION_RO		0x68
+#define SE_GENI_CLK_SEL			0x7c
+#define SE_GENI_DMA_MODE_EN		0x258
+#define SE_GENI_M_CMD0			0x600
+#define SE_GENI_M_CMD_CTRL_REG		0x604
+#define SE_GENI_M_IRQ_STATUS		0x610
+#define SE_GENI_M_IRQ_EN		0x614
+#define SE_GENI_M_IRQ_CLEAR		0x618
+#define SE_GENI_S_CMD0			0x630
+#define SE_GENI_S_CMD_CTRL_REG		0x634
+#define SE_GENI_S_IRQ_STATUS		0x640
+#define SE_GENI_S_IRQ_EN		0x644
+#define SE_GENI_S_IRQ_CLEAR		0x648
+#define SE_GENI_TX_FIFOn		0x700
+#define SE_GENI_RX_FIFOn		0x780
+#define SE_GENI_TX_FIFO_STATUS		0x800
+#define SE_GENI_RX_FIFO_STATUS		0x804
+#define SE_GENI_TX_WATERMARK_REG	0x80c
+#define SE_GENI_RX_WATERMARK_REG	0x810
+#define SE_GENI_RX_RFR_WATERMARK_REG	0x814
+#define SE_GENI_IOS			0x908
+#define SE_DMA_TX_IRQ_STAT		0xc40
+#define SE_DMA_TX_IRQ_CLR		0xc44
+#define SE_DMA_TX_FSM_RST		0xc58
+#define SE_DMA_RX_IRQ_STAT		0xd40
+#define SE_DMA_RX_IRQ_CLR		0xd44
+#define SE_DMA_RX_LEN_IN		0xd54
+#define SE_DMA_RX_FSM_RST		0xd58
+#define SE_HW_PARAM_0			0xe24
+#define SE_HW_PARAM_1			0xe28
+
+/* GENI_FORCE_DEFAULT_REG fields */
+#define FORCE_DEFAULT	BIT(0)
+
+/* GENI_STATUS fields */
+#define M_GENI_CMD_ACTIVE		BIT(0)
+#define S_GENI_CMD_ACTIVE		BIT(12)
+
+/* GENI_SER_M_CLK_CFG/GENI_SER_S_CLK_CFG */
+#define SER_CLK_EN			BIT(0)
+#define CLK_DIV_MSK			GENMASK(15, 4)
+#define CLK_DIV_SHFT			4
+
+/* GENI_IF_DISABLE_RO fields */
+#define FIFO_IF_DISABLE			(BIT(0))
+
+/* GENI_FW_REVISION_RO fields */
+#define FW_REV_PROTOCOL_MSK		GENMASK(15, 8)
+#define FW_REV_PROTOCOL_SHFT		8
+
+/* GENI_CLK_SEL fields */
+#define CLK_SEL_MSK			GENMASK(2, 0)
+
+/* SE_GENI_DMA_MODE_EN */
+#define GENI_DMA_MODE_EN		BIT(0)
+
+/* GENI_M_CMD0 fields */
+#define M_OPCODE_MSK			GENMASK(31, 27)
+#define M_OPCODE_SHFT			27
+#define M_PARAMS_MSK			GENMASK(26, 0)
+
+/* GENI_M_CMD_CTRL_REG */
+#define M_GENI_CMD_CANCEL		BIT(2)
+#define M_GENI_CMD_ABORT		BIT(1)
+#define M_GENI_DISABLE			BIT(0)
+
+/* GENI_S_CMD0 fields */
+#define S_OPCODE_MSK			GENMASK(31, 27)
+#define S_OPCODE_SHFT			27
+#define S_PARAMS_MSK			GENMASK(26, 0)
+
+/* GENI_S_CMD_CTRL_REG */
+#define S_GENI_CMD_CANCEL		BIT(2)
+#define S_GENI_CMD_ABORT		BIT(1)
+#define S_GENI_DISABLE			BIT(0)
+
+/* GENI_M_IRQ_EN fields */
+#define M_CMD_DONE_EN			BIT(0)
+#define M_CMD_OVERRUN_EN		BIT(1)
+#define M_ILLEGAL_CMD_EN		BIT(2)
+#define M_CMD_FAILURE_EN		BIT(3)
+#define M_CMD_CANCEL_EN			BIT(4)
+#define M_CMD_ABORT_EN			BIT(5)
+#define M_TIMESTAMP_EN			BIT(6)
+#define M_RX_IRQ_EN			BIT(7)
+#define M_GP_SYNC_IRQ_0_EN		BIT(8)
+#define M_GP_IRQ_0_EN			BIT(9)
+#define M_GP_IRQ_1_EN			BIT(10)
+#define M_GP_IRQ_2_EN			BIT(11)
+#define M_GP_IRQ_3_EN			BIT(12)
+#define M_GP_IRQ_4_EN			BIT(13)
+#define M_GP_IRQ_5_EN			BIT(14)
+#define M_IO_DATA_DEASSERT_EN		BIT(22)
+#define M_IO_DATA_ASSERT_EN		BIT(23)
+#define M_RX_FIFO_RD_ERR_EN		BIT(24)
+#define M_RX_FIFO_WR_ERR_EN		BIT(25)
+#define M_RX_FIFO_WATERMARK_EN		BIT(26)
+#define M_RX_FIFO_LAST_EN		BIT(27)
+#define M_TX_FIFO_RD_ERR_EN		BIT(28)
+#define M_TX_FIFO_WR_ERR_EN		BIT(29)
+#define M_TX_FIFO_WATERMARK_EN		BIT(30)
+#define M_SEC_IRQ_EN			BIT(31)
+#define M_COMMON_GENI_M_IRQ_EN	(GENMASK(6, 1) | \
+				M_IO_DATA_DEASSERT_EN | \
+				M_IO_DATA_ASSERT_EN | M_RX_FIFO_RD_ERR_EN | \
+				M_RX_FIFO_WR_ERR_EN | M_TX_FIFO_RD_ERR_EN | \
+				M_TX_FIFO_WR_ERR_EN)
+
+/* GENI_S_IRQ_EN fields */
+#define S_CMD_DONE_EN			BIT(0)
+#define S_CMD_OVERRUN_EN		BIT(1)
+#define S_ILLEGAL_CMD_EN		BIT(2)
+#define S_CMD_FAILURE_EN		BIT(3)
+#define S_CMD_CANCEL_EN			BIT(4)
+#define S_CMD_ABORT_EN			BIT(5)
+#define S_GP_SYNC_IRQ_0_EN		BIT(8)
+#define S_GP_IRQ_0_EN			BIT(9)
+#define S_GP_IRQ_1_EN			BIT(10)
+#define S_GP_IRQ_2_EN			BIT(11)
+#define S_GP_IRQ_3_EN			BIT(12)
+#define S_GP_IRQ_4_EN			BIT(13)
+#define S_GP_IRQ_5_EN			BIT(14)
+#define S_IO_DATA_DEASSERT_EN		BIT(22)
+#define S_IO_DATA_ASSERT_EN		BIT(23)
+#define S_RX_FIFO_RD_ERR_EN		BIT(24)
+#define S_RX_FIFO_WR_ERR_EN		BIT(25)
+#define S_RX_FIFO_WATERMARK_EN		BIT(26)
+#define S_RX_FIFO_LAST_EN		BIT(27)
+#define S_COMMON_GENI_S_IRQ_EN	(GENMASK(5, 1) | GENMASK(13, 9) | \
+				 S_RX_FIFO_RD_ERR_EN | S_RX_FIFO_WR_ERR_EN)
+
+/*  GENI_/TX/RX/RX_RFR/_WATERMARK_REG fields */
+#define WATERMARK_MSK			GENMASK(5, 0)
+
+/* GENI_TX_FIFO_STATUS fields */
+#define TX_FIFO_WC			GENMASK(27, 0)
+
+/*  GENI_RX_FIFO_STATUS fields */
+#define RX_LAST				BIT(31)
+#define RX_LAST_BYTE_VALID_MSK		GENMASK(30, 28)
+#define RX_LAST_BYTE_VALID_SHFT		28
+#define RX_FIFO_WC_MSK			GENMASK(24, 0)
+
+/* SE_GENI_IOS fields */
+#define IO2_DATA_IN			BIT(1)
+#define RX_DATA_IN			BIT(0)
+
+/* SE_DMA_TX_IRQ_STAT Register fields */
+#define TX_DMA_DONE			BIT(0)
+#define TX_EOT				BIT(1)
+#define TX_SBE				BIT(2)
+#define TX_RESET_DONE			BIT(3)
+
+/* SE_DMA_RX_IRQ_STAT Register fields */
+#define RX_DMA_DONE			BIT(0)
+#define RX_EOT				BIT(1)
+#define RX_SBE				BIT(2)
+#define RX_RESET_DONE			BIT(3)
+#define RX_FLUSH_DONE			BIT(4)
+#define RX_DMA_PARITY_ERR		BIT(5)
+#define RX_DMA_BREAK			GENMASK(8, 7)
+#define RX_GENI_GP_IRQ			GENMASK(10, 5)
+#define RX_GENI_CANCEL_IRQ		BIT(11)
+#define RX_GENI_GP_IRQ_EXT		GENMASK(13, 12)
+
+/* SE_HW_PARAM_0 fields */
+#define TX_FIFO_WIDTH_MSK		GENMASK(29, 24)
+#define TX_FIFO_WIDTH_SHFT		24
+#define TX_FIFO_DEPTH_MSK		GENMASK(21, 16)
+#define TX_FIFO_DEPTH_SHFT		16
+
+/* SE_HW_PARAM_1 fields */
+#define RX_FIFO_WIDTH_MSK		GENMASK(29, 24)
+#define RX_FIFO_WIDTH_SHFT		24
+#define RX_FIFO_DEPTH_MSK		GENMASK(21, 16)
+#define RX_FIFO_DEPTH_SHFT		16
+
+#define HW_VER_MAJOR_MASK		GENMASK(31, 28)
+#define HW_VER_MAJOR_SHFT		28
+#define HW_VER_MINOR_MASK		GENMASK(27, 16)
+#define HW_VER_MINOR_SHFT		16
+#define HW_VER_STEP_MASK		GENMASK(15, 0)
+
+#define GENI_SE_VERSION_MAJOR(ver) ((ver & HW_VER_MAJOR_MASK) >> HW_VER_MAJOR_SHFT)
+#define GENI_SE_VERSION_MINOR(ver) ((ver & HW_VER_MINOR_MASK) >> HW_VER_MINOR_SHFT)
+#define GENI_SE_VERSION_STEP(ver) (ver & HW_VER_STEP_MASK)
+
+/* QUP SE VERSION value for major number 2 and minor number 5 */
+#define QUP_SE_VERSION_2_5                  0x20050000
+
+/*
+ * Define bandwidth thresholds that cause the underlying Core 2X interconnect
+ * clock to run at the named frequency. These baseline values are recommended
+ * by the hardware team, and are not dynamically scaled with GENI bandwidth
+ * beyond basic on/off.
+ */
+#define CORE_2X_19_2_MHZ		960
+#define CORE_2X_50_MHZ			2500
+#define CORE_2X_100_MHZ			5000
+#define CORE_2X_150_MHZ			7500
+#define CORE_2X_200_MHZ			10000
+#define CORE_2X_236_MHZ			16383
+
+#define GENI_DEFAULT_BW			Bps_to_icc(1000)
+
+#if IS_ENABLED(CONFIG_QCOM_GENI_SE)
+
+u32 geni_se_get_qup_hw_version(struct geni_se *se);
+
+/**
+ * geni_se_read_proto() - Read the protocol configured for a serial engine
+ * @se:		Pointer to the concerned serial engine.
+ *
+ * Return: Protocol value as configured in the serial engine.
+ */
+static inline u32 geni_se_read_proto(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + GENI_FW_REVISION_RO);
+
+	return (val & FW_REV_PROTOCOL_MSK) >> FW_REV_PROTOCOL_SHFT;
+}
+
+/**
+ * geni_se_setup_m_cmd() - Setup the primary sequencer
+ * @se:		Pointer to the concerned serial engine.
+ * @cmd:	Command/Operation to setup in the primary sequencer.
+ * @params:	Parameter for the sequencer command.
+ *
+ * This function is used to configure the primary sequencer with the
+ * command and its associated parameters.
+ */
+static inline void geni_se_setup_m_cmd(struct geni_se *se, u32 cmd, u32 params)
+{
+	u32 m_cmd;
+
+	m_cmd = (cmd << M_OPCODE_SHFT) | (params & M_PARAMS_MSK);
+	writel(m_cmd, se->base + SE_GENI_M_CMD0);
+}
+
+/**
+ * geni_se_setup_s_cmd() - Setup the secondary sequencer
+ * @se:		Pointer to the concerned serial engine.
+ * @cmd:	Command/Operation to setup in the secondary sequencer.
+ * @params:	Parameter for the sequencer command.
+ *
+ * This function is used to configure the secondary sequencer with the
+ * command and its associated parameters.
+ */
+static inline void geni_se_setup_s_cmd(struct geni_se *se, u32 cmd, u32 params)
+{
+	u32 s_cmd;
+
+	s_cmd = readl_relaxed(se->base + SE_GENI_S_CMD0);
+	s_cmd &= ~(S_OPCODE_MSK | S_PARAMS_MSK);
+	s_cmd |= (cmd << S_OPCODE_SHFT);
+	s_cmd |= (params & S_PARAMS_MSK);
+	writel(s_cmd, se->base + SE_GENI_S_CMD0);
+}
+
+/**
+ * geni_se_cancel_m_cmd() - Cancel the command configured in the primary
+ *                          sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to cancel the currently configured command in the
+ * primary sequencer.
+ */
+static inline void geni_se_cancel_m_cmd(struct geni_se *se)
+{
+	writel_relaxed(M_GENI_CMD_CANCEL, se->base + SE_GENI_M_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_cancel_s_cmd() - Cancel the command configured in the secondary
+ *                          sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to cancel the currently configured command in the
+ * secondary sequencer.
+ */
+static inline void geni_se_cancel_s_cmd(struct geni_se *se)
+{
+	writel_relaxed(S_GENI_CMD_CANCEL, se->base + SE_GENI_S_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_abort_m_cmd() - Abort the command configured in the primary sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to force abort the currently configured command in the
+ * primary sequencer.
+ */
+static inline void geni_se_abort_m_cmd(struct geni_se *se)
+{
+	writel_relaxed(M_GENI_CMD_ABORT, se->base + SE_GENI_M_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_abort_s_cmd() - Abort the command configured in the secondary
+ *                         sequencer
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to force abort the currently configured command in the
+ * secondary sequencer.
+ */
+static inline void geni_se_abort_s_cmd(struct geni_se *se)
+{
+	writel_relaxed(S_GENI_CMD_ABORT, se->base + SE_GENI_S_CMD_CTRL_REG);
+}
+
+/**
+ * geni_se_get_tx_fifo_depth() - Get the TX fifo depth of the serial engine
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to get the depth i.e. number of elements in the
+ * TX fifo of the serial engine.
+ *
+ * Return: TX fifo depth in units of FIFO words.
+ */
+static inline u32 geni_se_get_tx_fifo_depth(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + SE_HW_PARAM_0);
+
+	return (val & TX_FIFO_DEPTH_MSK) >> TX_FIFO_DEPTH_SHFT;
+}
+
+/**
+ * geni_se_get_tx_fifo_width() - Get the TX fifo width of the serial engine
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to get the width i.e. word size per element in the
+ * TX fifo of the serial engine.
+ *
+ * Return: TX fifo width in bits
+ */
+static inline u32 geni_se_get_tx_fifo_width(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + SE_HW_PARAM_0);
+
+	return (val & TX_FIFO_WIDTH_MSK) >> TX_FIFO_WIDTH_SHFT;
+}
+
+/**
+ * geni_se_get_rx_fifo_depth() - Get the RX fifo depth of the serial engine
+ * @se:	Pointer to the concerned serial engine.
+ *
+ * This function is used to get the depth i.e. number of elements in the
+ * RX fifo of the serial engine.
+ *
+ * Return: RX fifo depth in units of FIFO words
+ */
+static inline u32 geni_se_get_rx_fifo_depth(struct geni_se *se)
+{
+	u32 val;
+
+	val = readl_relaxed(se->base + SE_HW_PARAM_1);
+
+	return (val & RX_FIFO_DEPTH_MSK) >> RX_FIFO_DEPTH_SHFT;
+}
+
+void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr);
+
+void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode);
+
+void geni_se_config_packing(struct geni_se *se, int bpw, int pack_words,
+			    bool msb_to_lsb, bool tx_cfg, bool rx_cfg);
+
+int geni_se_resources_off(struct geni_se *se);
+
+int geni_se_resources_on(struct geni_se *se);
+
+int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl);
+
+int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq,
+			   unsigned int *index, unsigned long *res_freq,
+			   bool exact);
+
+int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len,
+			dma_addr_t *iova);
+
+int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len,
+			dma_addr_t *iova);
+
+void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
+
+void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
+
+int geni_icc_get(struct geni_se *se, const char *icc_ddr);
+
+int geni_icc_set_bw(struct geni_se *se);
+void geni_icc_set_tag(struct geni_se *se, u32 tag);
+
+int geni_icc_enable(struct geni_se *se);
+
+int geni_icc_disable(struct geni_se *se);
+#endif
+#endif