diff options
| -rw-r--r-- | Documentation/devicetree/bindings/serial/8250_omap.yaml | 1 | ||||
| -rw-r--r-- | drivers/soc/fsl/qe/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_tegra.c | 4 | ||||
| -rw-r--r-- | drivers/tty/serial/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/cpm_uart/cpm_uart.h | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/fsl_lpuart.c | 44 |
6 files changed, 30 insertions, 27 deletions
diff --git a/Documentation/devicetree/bindings/serial/8250_omap.yaml b/Documentation/devicetree/bindings/serial/8250_omap.yaml index eb3488d8f9ee..6a7be42da523 100644 --- a/Documentation/devicetree/bindings/serial/8250_omap.yaml +++ b/Documentation/devicetree/bindings/serial/8250_omap.yaml @@ -70,6 +70,7 @@ properties: dsr-gpios: true rng-gpios: true dcd-gpios: true + rs485-rts-active-high: true rts-gpio: true power-domains: true clock-frequency: true diff --git a/drivers/soc/fsl/qe/Kconfig b/drivers/soc/fsl/qe/Kconfig index 7268c2fbcbc1..e0d096607fef 100644 --- a/drivers/soc/fsl/qe/Kconfig +++ b/drivers/soc/fsl/qe/Kconfig @@ -36,7 +36,7 @@ config UCC config CPM_TSA tristate "CPM TSA support" depends on OF && HAS_IOMEM - depends on CPM1 || COMPILE_TEST + depends on CPM1 || (CPM && COMPILE_TEST) help Freescale CPM Time Slot Assigner (TSA) controller. @@ -47,7 +47,7 @@ config CPM_TSA config CPM_QMC tristate "CPM QMC support" depends on OF && HAS_IOMEM - depends on CPM1 || (FSL_SOC && COMPILE_TEST) + depends on CPM1 || (FSL_SOC && CPM && COMPILE_TEST) depends on CPM_TSA help Freescale CPM QUICC Multichannel Controller diff --git a/drivers/tty/serial/8250/8250_tegra.c b/drivers/tty/serial/8250/8250_tegra.c index 2509e7f74ccf..89956bbf34d9 100644 --- a/drivers/tty/serial/8250/8250_tegra.c +++ b/drivers/tty/serial/8250/8250_tegra.c @@ -113,13 +113,15 @@ static int tegra_uart_probe(struct platform_device *pdev) ret = serial8250_register_8250_port(&port8250); if (ret < 0) - goto err_clkdisable; + goto err_ctrl_assert; platform_set_drvdata(pdev, uart); uart->line = ret; return 0; +err_ctrl_assert: + reset_control_assert(uart->rst); err_clkdisable: clk_disable_unprepare(uart->clk); diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 398e5aac2e77..3e3fb377d90d 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -762,7 +762,7 @@ config SERIAL_PMACZILOG_CONSOLE config SERIAL_CPM tristate "CPM SCC/SMC serial port support" - depends on CPM2 || CPM1 || (PPC32 && COMPILE_TEST) + depends on CPM2 || CPM1 select SERIAL_CORE help This driver supports the SCC and SMC serial ports on Motorola diff --git a/drivers/tty/serial/cpm_uart/cpm_uart.h b/drivers/tty/serial/cpm_uart/cpm_uart.h index 0577618e78c0..46c03ed71c31 100644 --- a/drivers/tty/serial/cpm_uart/cpm_uart.h +++ b/drivers/tty/serial/cpm_uart/cpm_uart.h @@ -19,8 +19,6 @@ struct gpio_desc; #include "cpm_uart_cpm2.h" #elif defined(CONFIG_CPM1) #include "cpm_uart_cpm1.h" -#elif defined(CONFIG_COMPILE_TEST) -#include "cpm_uart_cpm2.h" #endif #define SERIAL_CPM_MAJOR 204 diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index c91916e13648..7486a2b8556c 100644 --- a/drivers/tty/serial/fsl_lpuart.c +++ b/drivers/tty/serial/fsl_lpuart.c @@ -1495,34 +1495,36 @@ static void lpuart_break_ctl(struct uart_port *port, int break_state) static void lpuart32_break_ctl(struct uart_port *port, int break_state) { - unsigned long temp, modem; - struct tty_struct *tty; - unsigned int cflag = 0; - - tty = tty_port_tty_get(&port->state->port); - if (tty) { - cflag = tty->termios.c_cflag; - tty_kref_put(tty); - } + unsigned long temp; - temp = lpuart32_read(port, UARTCTRL) & ~UARTCTRL_SBK; - modem = lpuart32_read(port, UARTMODIR); + temp = lpuart32_read(port, UARTCTRL); + /* + * LPUART IP now has two known bugs, one is CTS has higher priority than the + * break signal, which causes the break signal sending through UARTCTRL_SBK + * may impacted by the CTS input if the HW flow control is enabled. It + * exists on all platforms we support in this driver. + * Another bug is i.MX8QM LPUART may have an additional break character + * being sent after SBK was cleared. + * To avoid above two bugs, we use Transmit Data Inversion function to send + * the break signal instead of UARTCTRL_SBK. + */ if (break_state != 0) { - temp |= UARTCTRL_SBK; /* - * LPUART CTS has higher priority than SBK, need to disable CTS before - * asserting SBK to avoid any interference if flow control is enabled. + * Disable the transmitter to prevent any data from being sent out + * during break, then invert the TX line to send break. */ - if (cflag & CRTSCTS && modem & UARTMODIR_TXCTSE) - lpuart32_write(port, modem & ~UARTMODIR_TXCTSE, UARTMODIR); + temp &= ~UARTCTRL_TE; + lpuart32_write(port, temp, UARTCTRL); + temp |= UARTCTRL_TXINV; + lpuart32_write(port, temp, UARTCTRL); } else { - /* Re-enable the CTS when break off. */ - if (cflag & CRTSCTS && !(modem & UARTMODIR_TXCTSE)) - lpuart32_write(port, modem | UARTMODIR_TXCTSE, UARTMODIR); + /* Disable the TXINV to turn off break and re-enable transmitter. */ + temp &= ~UARTCTRL_TXINV; + lpuart32_write(port, temp, UARTCTRL); + temp |= UARTCTRL_TE; + lpuart32_write(port, temp, UARTCTRL); } - - lpuart32_write(port, temp, UARTCTRL); } static void lpuart_setup_watermark(struct lpuart_port *sport) |