3 files changed, 59 insertions, 15 deletions

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index ae8494944c45..11c8c19f0fb7 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -448,8 +448,10 @@ config PATA_MARVELL
 	tristate "Marvell PATA support via legacy mode"
 	depends on PCI
 	help
-	  This option enables limited support for the Marvell 88SE6145 ATA
-	  controller.
+	  This option enables limited support for the Marvell 88SE61xx ATA
+	  controllers. If you wish to use only the SATA ports then select
+	  the AHCI driver alone. If you wish to the use the PATA port or
+	  both SATA and PATA include this driver.
 
 	  If unsure, say N.
 
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index c729e6988bbb..bce26ee3806e 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -610,6 +610,15 @@ module_param(ahci_em_messages, int, 0444);
 MODULE_PARM_DESC(ahci_em_messages,
 	"Set AHCI Enclosure Management Message type (0 = disabled, 1 = LED");
 
+#if defined(CONFIG_PATA_MARVELL) || defined(CONFIG_PATA_MARVELL_MODULE)
+static int marvell_enable;
+#else
+static int marvell_enable = 1;
+#endif
+module_param(marvell_enable, int, 0644);
+MODULE_PARM_DESC(marvell_enable, "Marvell SATA via AHCI (1 = enabled)");
+
+
 static inline int ahci_nr_ports(u32 cap)
 {
 	return (cap & 0x1f) + 1;
@@ -732,6 +741,8 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
 			   "MV_AHCI HACK: port_map %x -> %x\n",
 			   port_map,
 			   port_map & mv);
+		dev_printk(KERN_ERR, &pdev->dev,
+			  "Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n");
 
 		port_map &= mv;
 	}
@@ -2533,6 +2544,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (!printed_version++)
 		dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
 
+	/* The AHCI driver can only drive the SATA ports, the PATA driver
+	   can drive them all so if both drivers are selected make sure
+	   AHCI stays out of the way */
+	if (pdev->vendor == PCI_VENDOR_ID_MARVELL && !marvell_enable)
+		return -ENODEV;
+
 	/* acquire resources */
 	rc = pcim_enable_device(pdev);
 	if (rc)
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 24a011b25024..0d87eec84966 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -20,29 +20,30 @@
 #include <linux/ata.h>
 
 #define DRV_NAME	"pata_marvell"
-#define DRV_VERSION	"0.1.4"
+#define DRV_VERSION	"0.1.6"
 
 /**
- *	marvell_pre_reset	-	check for 40/80 pin
- *	@link: link
- *	@deadline: deadline jiffies for the operation
+ *	marvell_pata_active	-	check if PATA is active
+ *	@pdev: PCI device
  *
- *	Perform the PATA port setup we need.
+ *	Returns 1 if the PATA port may be active. We know how to check this
+ *	for the 6145 but not the other devices
  */
 
-static int marvell_pre_reset(struct ata_link *link, unsigned long deadline)
+static int marvell_pata_active(struct pci_dev *pdev)
 {
-	struct ata_port *ap = link->ap;
-	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int i;
 	u32 devices;
 	void __iomem *barp;
-	int i;
 
-	/* Check if our port is enabled */
+	/* We don't yet know how to do this for other devices */
+	if (pdev->device != 0x6145)
+		return 1;	
 
 	barp = pci_iomap(pdev, 5, 0x10);
 	if (barp == NULL)
 		return -ENOMEM;
+
 	printk("BAR5:");
 	for(i = 0; i <= 0x0F; i++)
 		printk("%02X:%02X ", i, ioread8(barp + i));
@@ -51,9 +52,27 @@ static int marvell_pre_reset(struct ata_link *link, unsigned long deadline)
 	devices = ioread32(barp + 0x0C);
 	pci_iounmap(pdev, barp);
 
-	if ((pdev->device == 0x6145) && (ap->port_no == 0) &&
-	    (!(devices & 0x10)))	/* PATA enable ? */
-		return -ENOENT;
+	if (devices & 0x10)
+		return 1;
+	return 0;
+}
+
+/**
+ *	marvell_pre_reset	-	check for 40/80 pin
+ *	@link: link
+ *	@deadline: deadline jiffies for the operation
+ *
+ *	Perform the PATA port setup we need.
+ */
+
+static int marvell_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+	struct ata_port *ap = link->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+	if (pdev->device == 0x6145 && ap->port_no == 0 &&
+		!marvell_pata_active(pdev))	/* PATA enable ? */
+			return -ENOENT;
 
 	return ata_sff_prereset(link, deadline);
 }
@@ -128,6 +147,12 @@ static int marvell_init_one (struct pci_dev *pdev, const struct pci_device_id *i
 	if (pdev->device == 0x6101)
 		ppi[1] = &ata_dummy_port_info;
 
+#if defined(CONFIG_AHCI) || defined(CONFIG_AHCI_MODULE)
+	if (!marvell_pata_active(pdev)) {
+		printk(KERN_INFO DRV_NAME ": PATA port not active, deferring to AHCI driver.\n");
+		return -ENODEV;
+	}
+#endif
 	return ata_pci_sff_init_one(pdev, ppi, &marvell_sht, NULL);
 }