summaryrefslogtreecommitdiff
path: root/drivers/ide/pdc202xx_new.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ide/pdc202xx_new.c')
-rw-r--r--drivers/ide/pdc202xx_new.c557
1 files changed, 0 insertions, 557 deletions
diff --git a/drivers/ide/pdc202xx_new.c b/drivers/ide/pdc202xx_new.c
deleted file mode 100644
index 4fcafb9121e0..000000000000
--- a/drivers/ide/pdc202xx_new.c
+++ /dev/null
@@ -1,557 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Promise TX2/TX4/TX2000/133 IDE driver
- *
- * Split from:
- * linux/drivers/ide/pdc202xx.c Version 0.35 Mar. 30, 2002
- * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2005-2007 MontaVista Software, Inc.
- * Portions Copyright (C) 1999 Promise Technology, Inc.
- * Author: Frank Tiernan (frankt@promise.com)
- * Released under terms of General Public License
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/ide.h>
-#include <linux/ktime.h>
-
-#include <asm/io.h>
-
-#ifdef CONFIG_PPC_PMAC
-#include <asm/prom.h>
-#endif
-
-#define DRV_NAME "pdc202xx_new"
-
-#undef DEBUG
-
-#ifdef DEBUG
-#define DBG(fmt, args...) printk("%s: " fmt, __func__, ## args)
-#else
-#define DBG(fmt, args...)
-#endif
-
-static u8 max_dma_rate(struct pci_dev *pdev)
-{
- u8 mode;
-
- switch(pdev->device) {
- case PCI_DEVICE_ID_PROMISE_20277:
- case PCI_DEVICE_ID_PROMISE_20276:
- case PCI_DEVICE_ID_PROMISE_20275:
- case PCI_DEVICE_ID_PROMISE_20271:
- case PCI_DEVICE_ID_PROMISE_20269:
- mode = 4;
- break;
- case PCI_DEVICE_ID_PROMISE_20270:
- case PCI_DEVICE_ID_PROMISE_20268:
- mode = 3;
- break;
- default:
- return 0;
- }
-
- return mode;
-}
-
-/**
- * get_indexed_reg - Get indexed register
- * @hwif: for the port address
- * @index: index of the indexed register
- */
-static u8 get_indexed_reg(ide_hwif_t *hwif, u8 index)
-{
- u8 value;
-
- outb(index, hwif->dma_base + 1);
- value = inb(hwif->dma_base + 3);
-
- DBG("index[%02X] value[%02X]\n", index, value);
- return value;
-}
-
-/**
- * set_indexed_reg - Set indexed register
- * @hwif: for the port address
- * @index: index of the indexed register
- */
-static void set_indexed_reg(ide_hwif_t *hwif, u8 index, u8 value)
-{
- outb(index, hwif->dma_base + 1);
- outb(value, hwif->dma_base + 3);
- DBG("index[%02X] value[%02X]\n", index, value);
-}
-
-/*
- * ATA Timing Tables based on 133 MHz PLL output clock.
- *
- * If the PLL outputs 100 MHz clock, the ASIC hardware will set
- * the timing registers automatically when "set features" command is
- * issued to the device. However, if the PLL output clock is 133 MHz,
- * the following tables must be used.
- */
-static struct pio_timing {
- u8 reg0c, reg0d, reg13;
-} pio_timings [] = {
- { 0xfb, 0x2b, 0xac }, /* PIO mode 0, IORDY off, Prefetch off */
- { 0x46, 0x29, 0xa4 }, /* PIO mode 1, IORDY off, Prefetch off */
- { 0x23, 0x26, 0x64 }, /* PIO mode 2, IORDY off, Prefetch off */
- { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */
- { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */
-};
-
-static struct mwdma_timing {
- u8 reg0e, reg0f;
-} mwdma_timings [] = {
- { 0xdf, 0x5f }, /* MWDMA mode 0 */
- { 0x6b, 0x27 }, /* MWDMA mode 1 */
- { 0x69, 0x25 }, /* MWDMA mode 2 */
-};
-
-static struct udma_timing {
- u8 reg10, reg11, reg12;
-} udma_timings [] = {
- { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */
- { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */
- { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */
- { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */
- { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */
- { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */
- { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */
-};
-
-static void pdcnew_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 adj = (drive->dn & 1) ? 0x08 : 0x00;
- const u8 speed = drive->dma_mode;
-
- /*
- * IDE core issues SETFEATURES_XFER to the drive first (thanks to
- * IDE_HFLAG_POST_SET_MODE in ->host_flags). PDC202xx hardware will
- * automatically set the timing registers based on 100 MHz PLL output.
- *
- * As we set up the PLL to output 133 MHz for UltraDMA/133 capable
- * chips, we must override the default register settings...
- */
- if (max_dma_rate(dev) == 4) {
- u8 mode = speed & 0x07;
-
- if (speed >= XFER_UDMA_0) {
- set_indexed_reg(hwif, 0x10 + adj,
- udma_timings[mode].reg10);
- set_indexed_reg(hwif, 0x11 + adj,
- udma_timings[mode].reg11);
- set_indexed_reg(hwif, 0x12 + adj,
- udma_timings[mode].reg12);
- } else {
- set_indexed_reg(hwif, 0x0e + adj,
- mwdma_timings[mode].reg0e);
- set_indexed_reg(hwif, 0x0f + adj,
- mwdma_timings[mode].reg0f);
- }
- } else if (speed == XFER_UDMA_2) {
- /* Set tHOLD bit to 0 if using UDMA mode 2 */
- u8 tmp = get_indexed_reg(hwif, 0x10 + adj);
-
- set_indexed_reg(hwif, 0x10 + adj, tmp & 0x7f);
- }
-}
-
-static void pdcnew_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 adj = (drive->dn & 1) ? 0x08 : 0x00;
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- if (max_dma_rate(dev) == 4) {
- set_indexed_reg(hwif, 0x0c + adj, pio_timings[pio].reg0c);
- set_indexed_reg(hwif, 0x0d + adj, pio_timings[pio].reg0d);
- set_indexed_reg(hwif, 0x13 + adj, pio_timings[pio].reg13);
- }
-}
-
-static u8 pdcnew_cable_detect(ide_hwif_t *hwif)
-{
- if (get_indexed_reg(hwif, 0x0b) & 0x04)
- return ATA_CBL_PATA40;
- else
- return ATA_CBL_PATA80;
-}
-
-static void pdcnew_reset(ide_drive_t *drive)
-{
- /*
- * Deleted this because it is redundant from the caller.
- */
- printk(KERN_WARNING "pdc202xx_new: %s channel reset.\n",
- drive->hwif->channel ? "Secondary" : "Primary");
-}
-
-/**
- * read_counter - Read the byte count registers
- * @dma_base: for the port address
- */
-static long read_counter(u32 dma_base)
-{
- u32 pri_dma_base = dma_base, sec_dma_base = dma_base + 0x08;
- u8 cnt0, cnt1, cnt2, cnt3;
- long count = 0, last;
- int retry = 3;
-
- do {
- last = count;
-
- /* Read the current count */
- outb(0x20, pri_dma_base + 0x01);
- cnt0 = inb(pri_dma_base + 0x03);
- outb(0x21, pri_dma_base + 0x01);
- cnt1 = inb(pri_dma_base + 0x03);
- outb(0x20, sec_dma_base + 0x01);
- cnt2 = inb(sec_dma_base + 0x03);
- outb(0x21, sec_dma_base + 0x01);
- cnt3 = inb(sec_dma_base + 0x03);
-
- count = (cnt3 << 23) | (cnt2 << 15) | (cnt1 << 8) | cnt0;
-
- /*
- * The 30-bit decrementing counter is read in 4 pieces.
- * Incorrect value may be read when the most significant bytes
- * are changing...
- */
- } while (retry-- && (((last ^ count) & 0x3fff8000) || last < count));
-
- DBG("cnt0[%02X] cnt1[%02X] cnt2[%02X] cnt3[%02X]\n",
- cnt0, cnt1, cnt2, cnt3);
-
- return count;
-}
-
-/**
- * detect_pll_input_clock - Detect the PLL input clock in Hz.
- * @dma_base: for the port address
- * E.g. 16949000 on 33 MHz PCI bus, i.e. half of the PCI clock.
- */
-static long detect_pll_input_clock(unsigned long dma_base)
-{
- ktime_t start_time, end_time;
- long start_count, end_count;
- long pll_input, usec_elapsed;
- u8 scr1;
-
- start_count = read_counter(dma_base);
- start_time = ktime_get();
-
- /* Start the test mode */
- outb(0x01, dma_base + 0x01);
- scr1 = inb(dma_base + 0x03);
- DBG("scr1[%02X]\n", scr1);
- outb(scr1 | 0x40, dma_base + 0x03);
-
- /* Let the counter run for 10 ms. */
- mdelay(10);
-
- end_count = read_counter(dma_base);
- end_time = ktime_get();
-
- /* Stop the test mode */
- outb(0x01, dma_base + 0x01);
- scr1 = inb(dma_base + 0x03);
- DBG("scr1[%02X]\n", scr1);
- outb(scr1 & ~0x40, dma_base + 0x03);
-
- /*
- * Calculate the input clock in Hz
- * (the clock counter is 30 bit wide and counts down)
- */
- usec_elapsed = ktime_us_delta(end_time, start_time);
- pll_input = ((start_count - end_count) & 0x3fffffff) / 10 *
- (10000000 / usec_elapsed);
-
- DBG("start[%ld] end[%ld]\n", start_count, end_count);
-
- return pll_input;
-}
-
-#ifdef CONFIG_PPC_PMAC
-static void apple_kiwi_init(struct pci_dev *pdev)
-{
- struct device_node *np = pci_device_to_OF_node(pdev);
- u8 conf;
-
- if (np == NULL || !of_device_is_compatible(np, "kiwi-root"))
- return;
-
- if (pdev->revision >= 0x03) {
- /* Setup chip magic config stuff (from darwin) */
- pci_read_config_byte (pdev, 0x40, &conf);
- pci_write_config_byte(pdev, 0x40, (conf | 0x01));
- }
-}
-#endif /* CONFIG_PPC_PMAC */
-
-static int init_chipset_pdcnew(struct pci_dev *dev)
-{
- const char *name = DRV_NAME;
- unsigned long dma_base = pci_resource_start(dev, 4);
- unsigned long sec_dma_base = dma_base + 0x08;
- long pll_input, pll_output, ratio;
- int f, r;
- u8 pll_ctl0, pll_ctl1;
-
- if (dma_base == 0)
- return -EFAULT;
-
-#ifdef CONFIG_PPC_PMAC
- apple_kiwi_init(dev);
-#endif
-
- /* Calculate the required PLL output frequency */
- switch(max_dma_rate(dev)) {
- case 4: /* it's 133 MHz for Ultra133 chips */
- pll_output = 133333333;
- break;
- case 3: /* and 100 MHz for Ultra100 chips */
- default:
- pll_output = 100000000;
- break;
- }
-
- /*
- * Detect PLL input clock.
- * On some systems, where PCI bus is running at non-standard clock rate
- * (e.g. 25 or 40 MHz), we have to adjust the cycle time.
- * PDC20268 and newer chips employ PLL circuit to help correct timing
- * registers setting.
- */
- pll_input = detect_pll_input_clock(dma_base);
- printk(KERN_INFO "%s %s: PLL input clock is %ld kHz\n",
- name, pci_name(dev), pll_input / 1000);
-
- /* Sanity check */
- if (unlikely(pll_input < 5000000L || pll_input > 70000000L)) {
- printk(KERN_ERR "%s %s: Bad PLL input clock %ld Hz, giving up!"
- "\n", name, pci_name(dev), pll_input);
- goto out;
- }
-
-#ifdef DEBUG
- DBG("pll_output is %ld Hz\n", pll_output);
-
- /* Show the current clock value of PLL control register
- * (maybe already configured by the BIOS)
- */
- outb(0x02, sec_dma_base + 0x01);
- pll_ctl0 = inb(sec_dma_base + 0x03);
- outb(0x03, sec_dma_base + 0x01);
- pll_ctl1 = inb(sec_dma_base + 0x03);
-
- DBG("pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
-#endif
-
- /*
- * Calculate the ratio of F, R and NO
- * POUT = (F + 2) / (( R + 2) * NO)
- */
- ratio = pll_output / (pll_input / 1000);
- if (ratio < 8600L) { /* 8.6x */
- /* Using NO = 0x01, R = 0x0d */
- r = 0x0d;
- } else if (ratio < 12900L) { /* 12.9x */
- /* Using NO = 0x01, R = 0x08 */
- r = 0x08;
- } else if (ratio < 16100L) { /* 16.1x */
- /* Using NO = 0x01, R = 0x06 */
- r = 0x06;
- } else if (ratio < 64000L) { /* 64x */
- r = 0x00;
- } else {
- /* Invalid ratio */
- printk(KERN_ERR "%s %s: Bad ratio %ld, giving up!\n",
- name, pci_name(dev), ratio);
- goto out;
- }
-
- f = (ratio * (r + 2)) / 1000 - 2;
-
- DBG("F[%d] R[%d] ratio*1000[%ld]\n", f, r, ratio);
-
- if (unlikely(f < 0 || f > 127)) {
- /* Invalid F */
- printk(KERN_ERR "%s %s: F[%d] invalid!\n",
- name, pci_name(dev), f);
- goto out;
- }
-
- pll_ctl0 = (u8) f;
- pll_ctl1 = (u8) r;
-
- DBG("Writing pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
-
- outb(0x02, sec_dma_base + 0x01);
- outb(pll_ctl0, sec_dma_base + 0x03);
- outb(0x03, sec_dma_base + 0x01);
- outb(pll_ctl1, sec_dma_base + 0x03);
-
- /* Wait the PLL circuit to be stable */
- mdelay(30);
-
-#ifdef DEBUG
- /*
- * Show the current clock value of PLL control register
- */
- outb(0x02, sec_dma_base + 0x01);
- pll_ctl0 = inb(sec_dma_base + 0x03);
- outb(0x03, sec_dma_base + 0x01);
- pll_ctl1 = inb(sec_dma_base + 0x03);
-
- DBG("pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
-#endif
-
- out:
- return 0;
-}
-
-static struct pci_dev *pdc20270_get_dev2(struct pci_dev *dev)
-{
- struct pci_dev *dev2;
-
- dev2 = pci_get_slot(dev->bus, PCI_DEVFN(PCI_SLOT(dev->devfn) + 1,
- PCI_FUNC(dev->devfn)));
-
- if (dev2 &&
- dev2->vendor == dev->vendor &&
- dev2->device == dev->device) {
-
- if (dev2->irq != dev->irq) {
- dev2->irq = dev->irq;
- printk(KERN_INFO DRV_NAME " %s: PCI config space "
- "interrupt fixed\n", pci_name(dev));
- }
-
- return dev2;
- }
-
- return NULL;
-}
-
-static const struct ide_port_ops pdcnew_port_ops = {
- .set_pio_mode = pdcnew_set_pio_mode,
- .set_dma_mode = pdcnew_set_dma_mode,
- .resetproc = pdcnew_reset,
- .cable_detect = pdcnew_cable_detect,
-};
-
-#define DECLARE_PDCNEW_DEV(udma) \
- { \
- .name = DRV_NAME, \
- .init_chipset = init_chipset_pdcnew, \
- .port_ops = &pdcnew_port_ops, \
- .host_flags = IDE_HFLAG_POST_SET_MODE | \
- IDE_HFLAG_ERROR_STOPS_FIFO | \
- IDE_HFLAG_OFF_BOARD, \
- .pio_mask = ATA_PIO4, \
- .mwdma_mask = ATA_MWDMA2, \
- .udma_mask = udma, \
- }
-
-static const struct ide_port_info pdcnew_chipsets[] = {
- /* 0: PDC202{68,70} */ DECLARE_PDCNEW_DEV(ATA_UDMA5),
- /* 1: PDC202{69,71,75,76,77} */ DECLARE_PDCNEW_DEV(ATA_UDMA6),
-};
-
-/**
- * pdc202new_init_one - called when a pdc202xx is found
- * @dev: the pdc202new device
- * @id: the matching pci id
- *
- * Called when the PCI registration layer (or the IDE initialization)
- * finds a device matching our IDE device tables.
- */
-
-static int pdc202new_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- const struct ide_port_info *d = &pdcnew_chipsets[id->driver_data];
- struct pci_dev *bridge = dev->bus->self;
-
- if (dev->device == PCI_DEVICE_ID_PROMISE_20270 && bridge &&
- bridge->vendor == PCI_VENDOR_ID_DEC &&
- bridge->device == PCI_DEVICE_ID_DEC_21150) {
- struct pci_dev *dev2;
-
- if (PCI_SLOT(dev->devfn) & 2)
- return -ENODEV;
-
- dev2 = pdc20270_get_dev2(dev);
-
- if (dev2) {
- int ret = ide_pci_init_two(dev, dev2, d, NULL);
- if (ret < 0)
- pci_dev_put(dev2);
- return ret;
- }
- }
-
- if (dev->device == PCI_DEVICE_ID_PROMISE_20276 && bridge &&
- bridge->vendor == PCI_VENDOR_ID_INTEL &&
- (bridge->device == PCI_DEVICE_ID_INTEL_I960 ||
- bridge->device == PCI_DEVICE_ID_INTEL_I960RM)) {
- printk(KERN_INFO DRV_NAME " %s: attached to I2O RAID controller,"
- " skipping\n", pci_name(dev));
- return -ENODEV;
- }
-
- return ide_pci_init_one(dev, d, NULL);
-}
-
-static void pdc202new_remove(struct pci_dev *dev)
-{
- struct ide_host *host = pci_get_drvdata(dev);
- struct pci_dev *dev2 = host->dev[1] ? to_pci_dev(host->dev[1]) : NULL;
-
- ide_pci_remove(dev);
- pci_dev_put(dev2);
-}
-
-static const struct pci_device_id pdc202new_pci_tbl[] = {
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), 0 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), 1 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 0 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 1 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 1 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 1 },
- { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 1 },
- { 0, },
-};
-MODULE_DEVICE_TABLE(pci, pdc202new_pci_tbl);
-
-static struct pci_driver pdc202new_pci_driver = {
- .name = "Promise_IDE",
- .id_table = pdc202new_pci_tbl,
- .probe = pdc202new_init_one,
- .remove = pdc202new_remove,
- .suspend = ide_pci_suspend,
- .resume = ide_pci_resume,
-};
-
-static int __init pdc202new_ide_init(void)
-{
- return ide_pci_register_driver(&pdc202new_pci_driver);
-}
-
-static void __exit pdc202new_ide_exit(void)
-{
- pci_unregister_driver(&pdc202new_pci_driver);
-}
-
-module_init(pdc202new_ide_init);
-module_exit(pdc202new_ide_exit);
-
-MODULE_AUTHOR("Andre Hedrick, Frank Tiernan");
-MODULE_DESCRIPTION("PCI driver module for Promise PDC20268 and higher");
-MODULE_LICENSE("GPL");
generated by cgit v1.2.3-70-g09d2 (git 2.47.1) at 2024-12-26 18:36:31 +0000