diff options
Diffstat (limited to 'drivers/net/dsa/microchip')
| -rw-r--r-- | drivers/net/dsa/microchip/ksz8.h | 4 | ||||
| -rw-r--r-- | drivers/net/dsa/microchip/ksz8795.c | 53 | ||||
| -rw-r--r-- | drivers/net/dsa/microchip/ksz_common.c | 1 |
3 files changed, 56 insertions, 2 deletions
diff --git a/drivers/net/dsa/microchip/ksz8.h b/drivers/net/dsa/microchip/ksz8.h index 4cea811e73ac..1a5225264e6a 100644 --- a/drivers/net/dsa/microchip/ksz8.h +++ b/drivers/net/dsa/microchip/ksz8.h @@ -56,5 +56,9 @@ int ksz8_reset_switch(struct ksz_device *dev); int ksz8_switch_init(struct ksz_device *dev); void ksz8_switch_exit(struct ksz_device *dev); int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu); +void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port, + unsigned int mode, phy_interface_t interface, + struct phy_device *phydev, int speed, int duplex, + bool tx_pause, bool rx_pause); #endif diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c index 4bf4d67557dc..88b10aa527d6 100644 --- a/drivers/net/dsa/microchip/ksz8795.c +++ b/drivers/net/dsa/microchip/ksz8795.c @@ -1439,6 +1439,57 @@ void ksz8_config_cpu_port(struct dsa_switch *ds) } } +/** + * ksz8_cpu_port_link_up - Configures the CPU port of the switch. + * @dev: The KSZ device instance. + * @speed: The desired link speed. + * @duplex: The desired duplex mode. + * @tx_pause: If true, enables transmit pause. + * @rx_pause: If true, enables receive pause. + * + * Description: + * The function configures flow control and speed settings for the CPU + * port of the switch based on the desired settings, current duplex mode, and + * speed. + */ +static void ksz8_cpu_port_link_up(struct ksz_device *dev, int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + const u16 *regs = dev->info->regs; + u8 ctrl = 0; + + /* SW_FLOW_CTRL, SW_HALF_DUPLEX, and SW_10_MBIT bits are bootstrappable + * at least on KSZ8873. They can have different values depending on your + * board setup. + */ + if (tx_pause || rx_pause) + ctrl |= SW_FLOW_CTRL; + + if (duplex == DUPLEX_HALF) + ctrl |= SW_HALF_DUPLEX; + + /* This hardware only supports SPEED_10 and SPEED_100. For SPEED_10 + * we need to set the SW_10_MBIT bit. Otherwise, we can leave it 0. + */ + if (speed == SPEED_10) + ctrl |= SW_10_MBIT; + + ksz_rmw8(dev, regs[S_BROADCAST_CTRL], SW_HALF_DUPLEX | SW_FLOW_CTRL | + SW_10_MBIT, ctrl); +} + +void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port, + unsigned int mode, phy_interface_t interface, + struct phy_device *phydev, int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + /* If the port is the CPU port, apply special handling. Only the CPU + * port is configured via global registers. + */ + if (dev->cpu_port == port) + ksz8_cpu_port_link_up(dev, speed, duplex, tx_pause, rx_pause); +} + static int ksz8_handle_global_errata(struct dsa_switch *ds) { struct ksz_device *dev = ds->priv; @@ -1487,8 +1538,6 @@ int ksz8_setup(struct dsa_switch *ds) */ ds->vlan_filtering_is_global = true; - ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true); - /* Enable automatic fast aging when link changed detected. */ ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true); diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c index 3fed406fb46a..0ee7cfb8d4bd 100644 --- a/drivers/net/dsa/microchip/ksz_common.c +++ b/drivers/net/dsa/microchip/ksz_common.c @@ -277,6 +277,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = { .mirror_add = ksz8_port_mirror_add, .mirror_del = ksz8_port_mirror_del, .get_caps = ksz8_get_caps, + .phylink_mac_link_up = ksz8_phylink_mac_link_up, .config_cpu_port = ksz8_config_cpu_port, .enable_stp_addr = ksz8_enable_stp_addr, .reset = ksz8_reset_switch, |