diff options
Diffstat (limited to 'drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h')
| -rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h | 178 |
1 files changed, 177 insertions, 1 deletions
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h index 2beb5430b876..b0779d773343 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h @@ -2182,6 +2182,45 @@ #define NIG_REG_P0_HWPFC_ENABLE 0x18078 #define NIG_REG_P0_LLH_FUNC_MEM2 0x18480 #define NIG_REG_P0_LLH_FUNC_MEM2_ENABLE 0x18440 +/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for + * the host. Bits [15:0] return the sequence ID of the packet. Bit 16 + * indicates the validity of the data in the buffer. Writing a 1 to bit 16 + * will clear the buffer. + */ +#define NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID 0x1875c +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * the host. This location returns the lower 32 bits of timestamp value. + */ +#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_LSB 0x18754 +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * the host. This location returns the upper 32 bits of timestamp value. + */ +#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_MSB 0x18758 +/* [RW 11] Mask register for the various parameters used in determining PTP + * packet presence. Set each bit to 1 to mask out the particular parameter. + * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of + * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP + * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC + * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of + * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable + * MAC DA 2. The reset default is set to mask out all parameters. + */ +#define NIG_REG_P0_LLH_PTP_PARAM_MASK 0x187a0 +/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set + * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . + * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP + * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; + * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC + * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype + * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset + * default is to mask out all of the rules. Note that rules 0-3 are for IPv4 + * packets only and require that the packet is IPv4 for the rules to match. + * Note that rules 4-7 are for IPv6 packets only and require that the packet + * is IPv6 for the rules to match. + */ +#define NIG_REG_P0_LLH_PTP_RULE_MASK 0x187a4 +/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */ +#define NIG_REG_P0_LLH_PTP_TO_HOST 0x187ac /* [RW 1] Input enable for RX MAC interface. */ #define NIG_REG_P0_MAC_IN_EN 0x185ac /* [RW 1] Output enable for TX MAC interface */ @@ -2194,6 +2233,17 @@ * priority field is extracted from the outer-most VLAN in receive packet. * Only COS 0 and COS 1 are supported in E2. */ #define NIG_REG_P0_PKT_PRIORITY_TO_COS 0x18054 +/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits + * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables + * V1 frame format in timesync event detection on RX side. Bit 2 enables V2 + * frame format in timesync event detection on RX side. Bit 3 enables + * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event + * detection on TX side. Bit 5 enables V2 frame format in timesync event + * detection on TX side. Note that for HW to detect PTP packet and extract + * data from the packet, at least one of the version bits of that traffic + * direction has to be enabled. + */ +#define NIG_REG_P0_PTP_EN 0x18788 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A * priority is mapped to COS 0 when the corresponding mask bit is 1. More * than one bit may be set; allowing multiple priorities to be mapped to one @@ -2300,7 +2350,46 @@ * Ethernet header. */ #define NIG_REG_P1_HDRS_AFTER_BASIC 0x1818c #define NIG_REG_P1_LLH_FUNC_MEM2 0x184c0 -#define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE 0x18460 +#define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE 0x18460a +/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for + * the host. Bits [15:0] return the sequence ID of the packet. Bit 16 + * indicates the validity of the data in the buffer. Writing a 1 to bit 16 + * will clear the buffer. + */ +#define NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID 0x18774 +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * the host. This location returns the lower 32 bits of timestamp value. + */ +#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_LSB 0x1876c +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * the host. This location returns the upper 32 bits of timestamp value. + */ +#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_MSB 0x18770 +/* [RW 11] Mask register for the various parameters used in determining PTP + * packet presence. Set each bit to 1 to mask out the particular parameter. + * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of + * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP + * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC + * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of + * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable + * MAC DA 2. The reset default is set to mask out all parameters. + */ +#define NIG_REG_P1_LLH_PTP_PARAM_MASK 0x187c8 +/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set + * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . + * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP + * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; + * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC + * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype + * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset + * default is to mask out all of the rules. Note that rules 0-3 are for IPv4 + * packets only and require that the packet is IPv4 for the rules to match. + * Note that rules 4-7 are for IPv6 packets only and require that the packet + * is IPv6 for the rules to match. + */ +#define NIG_REG_P1_LLH_PTP_RULE_MASK 0x187cc +/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */ +#define NIG_REG_P1_LLH_PTP_TO_HOST 0x187d4 /* [RW 32] Specify the client number to be assigned to each priority of the * strict priority arbiter. This register specifies bits 31:0 of the 36-bit * value. Priority 0 is the highest priority. Bits [3:0] are for priority 0 @@ -2342,6 +2431,17 @@ * priority field is extracted from the outer-most VLAN in receive packet. * Only COS 0 and COS 1 are supported in E2. */ #define NIG_REG_P1_PKT_PRIORITY_TO_COS 0x181a8 +/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits + * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables + * V1 frame format in timesync event detection on RX side. Bit 2 enables V2 + * frame format in timesync event detection on RX side. Bit 3 enables + * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event + * detection on TX side. Bit 5 enables V2 frame format in timesync event + * detection on TX side. Note that for HW to detect PTP packet and extract + * data from the packet, at least one of the version bits of that traffic + * direction has to be enabled. + */ +#define NIG_REG_P1_PTP_EN 0x187b0 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A * priority is mapped to COS 0 when the corresponding mask bit is 1. More * than one bit may be set; allowing multiple priorities to be mapped to one @@ -2361,6 +2461,78 @@ #define NIG_REG_P1_RX_MACFIFO_EMPTY 0x1858c /* [R 1] TLLH FIFO is empty. */ #define NIG_REG_P1_TLLH_FIFO_EMPTY 0x18338 +/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for + * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16 + * indicates the validity of the data in the buffer. Bit 17 indicates that + * the sequence ID is valid and it is waiting for the TX timestamp value. + * Bit 18 indicates whether the timestamp is from a SW request (value of 1) + * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer. + */ +#define NIG_REG_P0_TLLH_PTP_BUF_SEQID 0x187e0 +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * MCP. This location returns the lower 32 bits of timestamp value. + */ +#define NIG_REG_P0_TLLH_PTP_BUF_TS_LSB 0x187d8 +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * MCP. This location returns the upper 32 bits of timestamp value. + */ +#define NIG_REG_P0_TLLH_PTP_BUF_TS_MSB 0x187dc +/* [RW 11] Mask register for the various parameters used in determining PTP + * packet presence. Set each bit to 1 to mask out the particular parameter. + * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of + * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP + * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC + * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of + * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable + * MAC DA 2. The reset default is set to mask out all parameters. + */ +#define NIG_REG_P0_TLLH_PTP_PARAM_MASK 0x187f0 +/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set + * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . + * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP + * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; + * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC + * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype + * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset + * default is to mask out all of the rules. + */ +#define NIG_REG_P0_TLLH_PTP_RULE_MASK 0x187f4 +/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for + * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16 + * indicates the validity of the data in the buffer. Bit 17 indicates that + * the sequence ID is valid and it is waiting for the TX timestamp value. + * Bit 18 indicates whether the timestamp is from a SW request (value of 1) + * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer. + */ +#define NIG_REG_P1_TLLH_PTP_BUF_SEQID 0x187ec +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * MCP. This location returns the lower 32 bits of timestamp value. + */ +#define NIG_REG_P1_TLLH_PTP_BUF_TS_LSB 0x187e4 +/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for + * MCP. This location returns the upper 32 bits of timestamp value. + */ +#define NIG_REG_P1_TLLH_PTP_BUF_TS_MSB 0x187e8 +/* [RW 11] Mask register for the various parameters used in determining PTP + * packet presence. Set each bit to 1 to mask out the particular parameter. + * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of + * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP + * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC + * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of + * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable + * MAC DA 2. The reset default is set to mask out all parameters. + */ +#define NIG_REG_P1_TLLH_PTP_PARAM_MASK 0x187f8 +/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set + * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} . + * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP + * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1; + * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC + * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype + * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset + * default is to mask out all of the rules. + */ +#define NIG_REG_P1_TLLH_PTP_RULE_MASK 0x187fc /* [RW 32] Specify which of the credit registers the client is to be mapped * to. This register specifies bits 31:0 of the 36-bit value. Bits[3:0] are * for client 0; bits [35:32] are for client 8. For clients that are not @@ -2513,6 +2685,10 @@ swap is equal to SPIO pin that inputs from ifmux_serdes_swap. If 1 then ort swap is equal to ~nig_registers_port_swap.port_swap */ #define NIG_REG_STRAP_OVERRIDE 0x10398 +/* [WB 64] Addresses for TimeSync related registers in the timesync + * generator sub-module. + */ +#define NIG_REG_TIMESYNC_GEN_REG 0x18800 /* [RW 1] output enable for RX_XCM0 IF */ #define NIG_REG_XCM0_OUT_EN 0x100f0 /* [RW 1] output enable for RX_XCM1 IF */ |