| Age | Commit message (Collapse) | Author |
|---|
|
Add support for setting the VTCR_EL2 per VM, rather than hard
coding a value at boot time per CPU. This would allow us to tune
the stage2 page table parameters per VM in the later changes.
We compute the VTCR fields based on the system wide sanitised
feature registers, except for the hardware management of Access
Flags (VTCR_EL2.HA). It is fine to run a system with a mix of
CPUs that may or may not update the page table Access Flags.
Since the bit is RES0 on CPUs that don't support it, the bit
should be ignored on them.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Use the new helper for converting the parange to the physical shift.
Also, add the missing definitions for the VTCR_EL2 register fields
and use them instead of hard coding numbers.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Now that a VHE host uses tpidr_el2 for the cpu offset we no longer
need KVM to save/restore tpidr_el1. Move this from the 'common' code
into the non-vhe code. While we're at it, on VHE we don't need to
save the ELR or SPSR as kernel_entry in entry.S will have pushed these
onto the kernel stack, and will restore them from there. Move these
to the non-vhe code as we need them to get back to the host.
Finally remove the always-copy-tpidr we hid in the stage2 setup
code, cpufeature's enable callback will do this for VHE, we only
need KVM to do it for non-vhe. Add the copy into kvm-init instead.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Make tpidr_el2 a cpu-offset for per-cpu variables in the same way the
host uses tpidr_el1. This lets tpidr_el{1,2} have the same value, and
on VHE they can be the same register.
KVM calls hyp_panic() when anything unexpected happens. This may occur
while a guest owns the EL1 registers. KVM stashes the vcpu pointer in
tpidr_el2, which it uses to find the host context in order to restore
the host EL1 registers before parachuting into the host's panic().
The host context is a struct kvm_cpu_context allocated in the per-cpu
area, and mapped to hyp. Given the per-cpu offset for this CPU, this is
easy to find. Change hyp_panic() to take a pointer to the
struct kvm_cpu_context. Wrap these calls with an asm function that
retrieves the struct kvm_cpu_context from the host's per-cpu area.
Copy the per-cpu offset from the hosts tpidr_el1 into tpidr_el2 during
kvm init. (Later patches will make this unnecessary for VHE hosts)
We print out the vcpu pointer as part of the panic message. Add a back
reference to the 'running vcpu' in the host cpu context to preserve this.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We currently copy the physical address size from
ID_AA64MMFR0_EL1.PARange directly into TCR.(I)PS. This will not work for
4k and 16k granule kernels on systems that support 52-bit physical
addresses, since 52-bit addresses are only permitted with the 64k
granule.
To fix this, fall back to 48 bits when configuring the PA size when the
kernel does not support 52-bit PAs. When it does, fall back to 52, to
avoid similar problems in the future if the PA size is ever increased
above 52.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: tcr_set_pa_size macro renamed to tcr_compute_pa_size]
[catalin.marinas@arm.com: comments added to tcr_compute_pa_size]
[catalin.marinas@arm.com: definitions added for TCR_*PS_SHIFT]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Since the pte handling for hardware AF/DBM works even when the hardware
feature is not present, make the pte accessors implementation permanent
and remove the corresponding #ifdefs. The Kconfig option is kept as it
can still be used to disable the feature at the hardware level.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The ARMv8.1 architecture extensions introduce support for hardware
updates of the access and dirty information in page table entries. With
VTCR_EL2.HA enabled (bit 21), when the CPU accesses an IPA with the
PTE_AF bit cleared in the stage 2 page table, instead of raising an
Access Flag fault to EL2 the CPU sets the actual page table entry bit
(10). To ensure that kernel modifications to the page table do not
inadvertently revert a bit set by hardware updates, certain Stage 2
software pte/pmd operations must be performed atomically.
The main user of the AF bit is the kvm_age_hva() mechanism. The
kvm_age_hva_handler() function performs a "test and clear young" action
on the pte/pmd. This needs to be atomic in respect of automatic hardware
updates of the AF bit. Since the AF bit is in the same position for both
Stage 1 and Stage 2, the patch reuses the existing
ptep_test_and_clear_young() functionality if
__HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG is defined. Otherwise, the
existing pte_young/pte_mkold mechanism is preserved.
The kvm_set_s2pte_readonly() (and the corresponding pmd equivalent) have
to perform atomic modifications in order to avoid a race with updates of
the AF bit. The arm64 implementation has been re-written using
exclusives.
Currently, kvm_set_s2pte_writable() (and pmd equivalent) take a pointer
argument and modify the pte/pmd in place. However, these functions are
only used on local variables rather than actual page table entries, so
it makes more sense to follow the pte_mkwrite() approach for stage 1
attributes. The change to kvm_s2pte_mkwrite() makes it clear that these
functions do not modify the actual page table entries.
The (pte|pmd)_mkyoung() uses on Stage 2 entries (setting the AF bit
explicitly) do not need to be modified since hardware updates of the
dirty status are not supported by KVM, so there is no possibility of
losing such information.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We always thought that 40bits of PA range would be the minimum people
would actually build. Anything less is terrifyingly small.
Turns out that we were both right and wrong. Nobody has ever built
such a system, but the ARM Foundation Model has a PARange set to 36bits.
Just because we can. Oh well. Now, the KVM API explicitely says that
we offer a 40bit PA space to the VM, so we shouldn't run KVM on
the Foundation Model at all.
That being said, this patch offers a less agressive alternative, and
loudly warns about the configuration being unsupported. You'll still
be able to run VMs (at your own risks, though).
This is just a workaround until we have a proper userspace API where
we report the PARange to userspace.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
When we detect support for 16bit VMID in ID_AA64MMFR1, we set the
VTCR_EL2_VS field to 1 to make use of 16bit vmids. But, with
commit 3a3604bc5eb4 ("arm64: KVM: Switch to C-based stage2 init")
this is broken and we corrupt VTCR_EL2:T0SZ instead of updating the VS
field. VTCR_EL2_VS was actually defined to the field shift (19) and
not the real value for VS. This patch fixes the issue.
Fixes: commit 3a3604bc5eb4 ("arm64: KVM: Switch to C-based stage2 init")
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
In order to be able to move code outside of kvm/hyp, we need to make
the global hyp.h file accessible from a standard location.
include/asm/kvm_hyp.h seems good enough.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
There is no real need to leave the stage2 initialization as part
of the early HYP bootstrap, and we can easily postpone it to
the point where we can safely run C code.
This will help VHE, which doesn't need any of this bootstrap.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
