| Age | Commit message (Collapse) | Author |
|---|
|
Use the memory ranges published in discovery table to deduce NPS mode
of GC v9.4.3 VFs.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Vignesh Chander <Vignesh.Chander@amd.com>
Tested-by: Vignesh Chander <Vignesh.Chander@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add a callback to check if there is any condition detected by GMC block
for reset on init. One case is if a pending NPS change request is
detected. If reset is done because of NPS switch, refresh NPS info from
discovery table.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If a user has requested NPS mode switch, place the request through PSP
during unload of the driver. For devices which are part of a hive, all
requests are placed together. If one of them fails, revert back to the
current NPS mode.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add a sysfs interface to see available NPS modes to switch to -
cat /sys/bus/pci/devices/../available_memory_paritition
Make the current_memory_partition sysfs node read/write for requesting a
new NPS mode. The request is only cached and at a later point a driver
unload/reload is required to switch to the new NPS mode.
Ex:
echo NPS1 > /sys/bus/pci/devices/../current_memory_paritition
echo NPS4 > /sys/bus/pci/devices/../current_memory_paritition
The above interfaces will be available only if the SOC supports more than
one NPS mode.
Also modify the current memory partition sysfs logic to be more
generic.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add a common interface in GMC to request NPS mode through PSP. Also add
a variable in hive and gmc control to track the last requested mode.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_gmc_vram_cpu_pa has been unused since commit
087451f372bf ("drm/amdgpu: use generic fb helpers instead of setting up AMD own's.")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Drop pending_reset flag in gmc block. Instead use init level to
determine which type of init is preferred - in this case MINIMAL.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add address alignment support to the DCC VRAM buffers.
v2:
- adjust size based on the max_texture_channel_caches values
only for GFX12 DCC buffers.
- used AMDGPU_GEM_CREATE_GFX12_DCC flag to apply change only
for DCC buffers.
- roundup non power of two DCC buffer adjusted size to nearest
power of two number as the buddy allocator does not support non
power of two alignments. This applies only to the contiguous
DCC buffers.
v3:(Alex)
- rewrite the max texture channel caches comparison code in an
algorithmic way to determine the alignment size.
v4:(Alex)
- Move the logic from amdgpu_vram_mgr_dcc_alignment() to gmc_v12_0.c
and add a new gmc func callback for dcc alignment. If the callback
is non-NULL, call it to get the alignment, otherwise, use the default.
v5:(Alex)
- Set the Alignment to a default value if the callback doesn't exist.
- Add the callback to amdgpu_gmc_funcs.
v6:
- Fix checkpatch warning reported by Intel CI.
v7:(Christian)
- remove the AMDGPU_GEM_CREATE_GFX12_DCC flag and keep a flag that
checks the BO pinning and for a specific hw generation.
v8:(Christian)
- move this check into gmc_v12_0_get_dcc_alignment.
v9:
- Fix 32bit build errors
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit aa94b623cb9233b91ed342dd87ecd62e56ff4938)
|
|
Add GMC API to fetch NPS range information from discovery table. Use NPS
range information in GMC 9.4.3 SOCs when available, otherwise fallback
to software method.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's used for more than just SR-IOV now, so move it to
amdgpu_gmc.c and rename it to better match the functionality and
update the comments in the code paths to better document
when each path is used and why. No functional change.
Reviewed-by: Shaoyun.liu <Shaoyun.liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Shaoyun.Liu@amd.com
Cc: Christian.Koenig@amd.com
|
|
We normally place GART based on the location of VRAM and the
available address space around that, but provide an option
to force a particular location for hardware that needs it.
v2: Switch to passing the placement via parameter
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To disable AGP, the start needs to be set to a higher
value than the end. Set a default disable value for
the AGP aperture and allow the IP specific GMC code
to enable it selectively be calling amdgpu_gmc_agp_location().
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
That function never fails, drop the error return.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Testing for reset is pointless since the reset can start right after the
test.
The same PASID can be used by more than one VMID, invalidate each of them.
Move the KIQ and all the workaround handling into common GMC code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move the SDMA workaround necessary for Navi 1x into a higher layer.
v2: use dev_err
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update the invalid PTE flag setting with TF enabled.
This is to ensure, in addition to transitioning the
retry fault to a no-retry fault, it also causes the
wavefront to enter the trap handler. With the current
setting, the fault only transitions to a no-retry fault.
Additionally, have 2 sets of invalid PTE settings, one for
TF enabled, the other for TF disabled. The setting with
TF disabled, doesn't work with TF enabled.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update total channel number for umc v8_10.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On GFXv9.4.3 NUMA APUs, system memory locality must be determined per
page to choose the correct MTYPE. This patch adds a GMC callback that
can provide this per-page override and implements it for native mode.
Carve-out mode is not yet supported and will use the safe default
(remote) MTYPE for system memory.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-and-tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some ASICs have the device memory divided into multiple partitions. The
parititions could be denoted by a numa node or by a range of pages.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
GMC block handles memory related information, it makes more sense to
keep memory partition functions in gmc block.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On GPXIP 9.4.3 APU, in no carveout mode there is no real vram heap and
could be emulated by the driver over the interleaved NUMA system memory
and the APU could also be in the carveout mode during early development
stage or otherwise for debugging purpose so introduce a new member in
amdgpu_gmc to figure out whether the APU is in the native mode as per
the production configuration. AMD_IS_APU cannot be used for Accelerated
Processing Platform APUs as it might be used in a different context on
previous generations or on small APUs.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Tested-by: Graham Sider <graham.sider@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add XCC instance to select the correct KIQ ring when
flushing TLBs on a multi-XCC setup.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Tested-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Rework retry fault removal from the software filter by
storing an expired timestamp for a fault that is being removed.
When a new fault comes, and it matches an entry in the sw filter,
it will be added as a new fault only when its timestamp is greater
than the timestamp expiry of the fault in the sw filter.
This helps in avoiding stale faults being added back into the
filter and preventing legitimate faults from being handled.
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
If disable the mmhub vm contexts(set MMVM_CONTEXTS_DISABLE to 0xffff),
driver loading failed on vf due to fence fallback timer expired on all rings.
FLR cannot reset MMVM_CONTEXTS_DISABLE.
So this vf can not be recovered anymore unless trigger a whole gpu reset.
[How]
Under SRIOV, init MMVM_CONTEXTS_DISABLE in gmc11 golden register setting.
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Reviewed-by: Horace Chen <Horace.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Initialize umc ras block only when umc ip block
supports ras. Driver queries ras capabilities after
early_init, ras block init needs to be moved to
sw_init.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Save and restore gfxhub regs as they will be reset during mode 2
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
MES firmware needs the setting of VM_CONTEXT_CNTL to perform
vmid switch. Save the initial setting when hub initializing.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for mmhub v3.0
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For chips with IP discovery get this from the table,
hardcode it for older asics.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This will be useful in future patches.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some ASICs need reserved memory for firmware or other components,
which is not allowed to be used by driver.
amdgpu_gmc_get_reserved_allocation is to handle additional areas.
To avoid any missing calling,
merged amdgpu_gmc_get_reserved_allocation to
amdgpu_gmc_get_vbios_allocations.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move xgmi ras initialization from .late_init to .early_init, which let
xgmi ras can be initialized only once.
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch will add vram check function for GMC block.
It will write pattern data to the vram and then read back from the vram,
so that to verify the work status of vram.
This patch will cover gmc v6/7/8/9/10.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
1.Modify gmc block to fit for the unified ras block data and ops.
2.Change amdgpu_xgmi_ras_funcs to amdgpu_xgmi_ras, and the corresponding variable name remove _funcs suffix.
3.Remove the const flag of gmc ras variable so that gmc ras block can be able to be inserted into amdgpu device ras block link list.
4.Invoke amdgpu_ras_register_ras_block function to register gmc ras block into amdgpu device ras block link list.
5.Remove the redundant code about gmc in amdgpu_ras.c after using the unified ras block.
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
IH ring1 is used to process GPU retry fault, overflow is enabled to
drain retry fault because we want receive other interrupts while
handling retry fault to recover range. There is no overflow flag set
when wptr pass rptr. Use timestamp of rptr and wptr to handle overflow
and drain retry fault.
If fault timestamp goes backward, the fault is filtered and should not
be processed. Drain fault is finished if processed_timestamp is equal to
or larger than checkpoint timestamp.
Add amdgpu_ih_functions interface decode_iv_ts for different chips to
get timestamp from IV entry with different iv size and timestamp offset.
amdgpu_ih_decode_iv_ts_helper is used for vega10, vega20, navi10.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
region (v2)
Some ASICs such as Yellow Carp needs to reserve a region of video memory
to avoid access from driver. So this patch is to introduce a stolen
reserved buffer to protect specific buffer region.
v2: free this buffer in amdgpu_ttm_fini.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-and-Tested-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add interface to remove address from fault filter ring by resetting
fault ring entry key, then future vm fault on the address will be
processed to recover.
Define fault key as atomic64_t type to use atomic read/set/cmpxchg key
to protect fault ring access by interrupt handler and interrupt deferred
work for vg20. Change fault->timestamp to 48-bit to share same uint64_t
with 8-bit fault->next, it is enough for 48bit IH timestamp.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 2f055097daef498da57552f422f49de50a1573e6.
2f055097daef498da57552f422f49de50a1573e6 was a driver workaround
when PSP firmware was not ready. Now the PSP fw is ready so we
revert this driver workaround.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add one function to calculate BO's GPU physical address.
And another function to calculate BO's CPU physical address.
v2: Use functions vs macros (Christian)
Use more proper function names (Christian)
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
xgmi ras is not managed by gpu driver when gpu is
connected to cpu through xgmi. move all xgmi ras
functions to xgmi_ras_funcs so gpu driver only
initializes xgmi ras functions when it manages
xgmi ras.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: John Clements <John.Clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In passthrough configuration, hypervisior will trigger the SBR(Secondary bus reset) to the devices
without sync to each other. This could cause device hang since for XGMI configuration, all the devices
within the hive need to be reset at a limit time slot. This serial of patches try to solve this issue
by co-operate with new SMU which will only do minimum house keeping to response the SBR request but don't
do the real reset job and leave it to driver. Driver need to do the whole sw init and minimum HW init
to bring up the SMU and trigger the reset(possibly BACO) on all the ASICs at the same time
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Andrey Grodzovsky andrey.grodzovsky@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
More accurate words are used to address a
code review feedback
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
With the 2-level gart page table, vram is squeezed into gart aperture
and FB aperture is disabled. Therefore all VRAM virtual addresses are
in the GART aperture. However currently PSP requires TMR addresses
in FB aperture. So we need some design change at PSP FW level to support
this 2-level gart table driver change. Right now this PSP FW support
doesn't exist. To workaround this issue temporarily, FB aperture is
added back and the gart aperture address is converted back to FB aperture
for this PSP TMR address.
Will revert it after we get a fix from PSP FW.
v2: squash in tmr fix for other asics (Kevin)
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add functions to allocate PDB0, map it for CPU access,
and fill it.
Those functions are only used for 2-level vmid0 page
table construction
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If use gart for FB translation, we will squeeze vram into
sysvm aperture. This requires 2 level gart table. Add
page table depth and page table block size parameters
to gmc. This is prepare work to 2-level gart table
construction
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If use GART for FB translation, place both vram and gart to sysvm
aperture. AGP aperture is not set up in this case because it
is not used
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Modify the comment to reflect the fact that, if
use GART for vram address translation for vmid0,
[vram_start, vram_end] will be placed inside SYSVM
aperture, together with GART.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This applies to AMD Accelerated Processing Platforms that support host
gpu interconnect throguh a special link (xgmi). Aldebaran systems will
support this special feature for utilizing the benefits of host-gpu
cache coherence. This change outlines the basic framework for mapping
the GPU VRAM (HBM) to system address space making it accesible to the
host but managed by the amdgpu driver since this region is marked as
reserved memory in host address space by the underlying system firmware.
v2: switch to smuio callback function to check the type
of host-gpu interface (Hawking)
v3: use hub callbacks rather than direct function calls (Alex)
Reviewed-by: Oak Zeng <oak.zeng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This will allow us to have different defaults per asic
in a future patch.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's more related to memory management than memory
controller.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
