| Age | Commit message (Collapse) | Author |
|---|
|
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has
4 internal PHYs and 1 SGMII port. The chip id read from hardware is
same as KSZ9477, so software driver needs to create a new chip id and
group allowable functions under its chip data structure to
differentiate the product.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241109015705.82685-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce ksz_parse_dt_phy_config() to validate and parse PHY
configuration from the device tree for KSZ switches. This function
ensures proper setup of internal PHYs by checking `phy-handle`
properties, verifying expected PHY IDs, and handling parent node
mismatches. Sets the PHY mask on the MII bus if validation is
successful. Returns -EINVAL on configuration errors.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241106075942.1636998-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement side MDIO channel support for LAN937x switches, providing an
alternative to SPI for PHY management alongside existing SPI-based
switch configuration. This is needed to reduce SPI load, as SPI can be
relatively expensive for small packets compared to MDIO support.
Also, implemented static mappings for PHY addresses for various LAN937x
models to support different internal PHY configurations. Since the PHY
address mappings are not equal to the port indexes, this patch also
provides PHY address calculation based on hardware strapping
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace repeated cleanup code with a single error path using a label.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for accessing PHYs via a side MDIO interface in LAN937x
switches. The existing code already supports accessing PHYs via main
management interfaces, which can be SPI, I2C, or MDIO, depending on the
chip variant. This patch enables using a side MDIO bus, where SPI is
used for the main switch configuration and MDIO for managing the
integrated PHYs. On LAN937x, this is optional, allowing them to operate
in both configurations: SPI only, or SPI + MDIO. Typically, the SPI
interface is used for switch configuration, while MDIO handles PHY
management.
Additionally, update interrupt controller code to support non-linear
port to PHY address mapping, enabling correct interrupt handling for
configurations where PHY addresses do not directly correspond to port
indexes. This change ensures that the interrupt mechanism properly
aligns with the new, flexible PHY address mappings introduced by side
MDIO support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(for hellcreek driver)
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts and no adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5b5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba50 ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c16382 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997f5 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13af ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13af ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Prior to this patch ksz_ptp_msg_irq_setup() uses snprintf() to copy
strings. It does so by passing strings as the format argument of
snprintf(). This appears to be safe, due to the absence of format
specifiers in the strings, which are declared within the same function.
But nonetheless GCC 14 warns about it:
.../ksz_ptp.c:1109:55: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^~~~~~~
.../ksz_ptp.c:1109:55: note: treat the string as an argument to avoid this
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^
| "%s",
As what we are really dealing with here is a string copy, it seems make
sense to use a function designed for this purpose. In this case null
padding is not required, so strscpy is appropriate. And as the
destination is an array of fixed size, the 2-argument variant may be used.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241014-string-thing-v2-1-b9b29625060a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.
Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove macros that are already defined at more appropriate places.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoids the need for manual cleanup of_node_put() in early exits
from the loop by using for_each_available_child_of_node_scoped().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
KSZ8895/KSZ8864 is a switch family between KSZ8863/73 and KSZ8795, so it
shares some registers and functions in those switches already
implemented in the KSZ DSA driver.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Tested-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.h
c948c0973df5 ("bnxt_en: Don't clear ntuple filters and rss contexts during ethtool ops")
f2878cdeb754 ("bnxt_en: Add support to call FW to update a VNIC")
Link: https://patch.msgid.link/20240822210125.1542769-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When performing the port_hwtstamp_set operation, ptp_schedule_worker()
will be called if hardware timestamoing is enabled on any of the ports.
When using multiple ports for PTP, port_hwtstamp_set is executed for
each port. When called for the first time ptp_schedule_worker() returns
0. On subsequent calls it returns 1, indicating the worker is already
scheduled. Currently the ksz driver treats 1 as an error and fails to
complete the port_hwtstamp_set operation, thus leaving the timestamping
configuration for those ports unchanged.
This patch fixes this by ignoring the ptp_schedule_worker() return
value.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/7aae307a-35ca-4209-a850-7b2749d40f90@martin-whitaker.me.uk
Fixes: bb01ad30570b0 ("net: dsa: microchip: ptp: manipulating absolute time using ptp hw clock")
Signed-off-by: Martin Whitaker <foss@martin-whitaker.me.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240817094141.3332-1-foss@martin-whitaker.me.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The KSZ87xx switches have 32 static MAC address table entries and not
8. This fixes -ENOSPC non-critical errors from ksz8_add_sta_mac when
configured as a bridge.
Add a new ksz87xx_dev_ops structure to be able to use the
ksz_r_mib_stat64 pointer for this family; this corrects a wrong
mib->counters cast to ksz88xx_stats_raw. This fixes iproute2
statistics. Rename ksz8_dev_ops structure to ksz88x3_dev_ops, in line
with ksz_is_* naming conventions from ksz_common.h.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-6-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add WoL support for KSZ87xx family of switches. This code was tested
with a KSZ8794 chip.
Implement ksz_common usage of the new device-tree property
'microchip,pme-active-high'.
Make use of the now generalized ksz_common WoL functions, adding an
additional interrupt register write for KSZ87xx. Add helper functions
to convert from PME (port) read/writes to indirect register
read/writes in the dedicated ksz8795 sources. Add initial
configuration during (port) setup as per KSZ9477.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-5-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Generalize KSZ9477 WoL functions at ksz_common. Move dedicated registers
and generic masks to existing structures & defines for that purpose.
Introduction of PME (port) read/write helper functions, which happen
to be the generic read/write for KSZ9477 but not for the incoming
KSZ87xx patch.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-4-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move KSZ9477 WoL functions to ksz_common, in preparation for adding
KSZ87xx family support.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-3-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Keep the URL in a single line for easier copy-pasting.
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240812124346.597702-1-enguerrand.de-ribaucourt@savoirfairelinux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to respect the 80 columns limit, split the half-duplex
monitoring function in two.
This is just a styling change, no functional change.
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As noted in the device errata [1-8], EEE support is not fully operational
in the KSZ8567, KSZ9477, KSZ9567, KSZ9896, and KSZ9897 devices, causing
link drops when connected to another device that supports EEE. The patch
series "net: add EEE support for KSZ9477 switch family" merged in commit
9b0bf4f77162 caused EEE support to be enabled in these devices. A fix for
this regression for the KSZ9477 alone was merged in commit 08c6d8bae48c2.
This patch extends this fix to the other affected devices.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ8567R-Errata-DS80000752.pdf
[2] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ8567S-Errata-DS80000753.pdf
[3] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9477S-Errata-DS80000754.pdf
[4] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9567R-Errata-DS80000755.pdf
[5] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9567S-Errata-DS80000756.pdf
[6] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9896C-Errata-DS80000757.pdf
[7] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9897R-Errata-DS80000758.pdf
[8] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9897S-Errata-DS80000759.pdf
Fixes: 69d3b36ca045 ("net: dsa: microchip: enable EEE support") # for KSZ8567/KSZ9567/KSZ9896/KSZ9897
Link: https://lore.kernel.org/netdev/137ce1ee-0b68-4c96-a717-c8164b514eec@martin-whitaker.me.uk/
Signed-off-by: Martin Whitaker <foss@martin-whitaker.me.uk>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Link: https://patch.msgid.link/20240807205209.21464-1-foss@martin-whitaker.me.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The wol variable in ksz_port_set_mac_address() is declared with random
data, but the code in ksz_get_wol call may not be executed so the
WAKE_MAGIC check may be invalid resulting in an error message when
setting a MAC address after starting the DSA driver.
Fixes: 3b454b6390c3 ("net: dsa: microchip: ksz9477: Add Wake on Magic Packet support")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240805235200.24982-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set proper MAC capabilities for port 4 on LAN9371 and LAN9372 switches with
integrated 100BaseTX PHY. And introduce the is_lan937x_tx_phy() function to
reuse it where applicable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce error handling for lan937x_cfg function calls in lan937x_setup.
This change ensures that if any lan937x_cfg or ksz_rmw32 calls fails, the
function will return the appropriate error code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240703083820.3152100-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As described by the microchip article "LAN937X - The required
configuration for the external MAC port to operate at RGMII-to-RGMII
1Gbps link speed." [1]:
"When VPHY is enabled, the auto-negotiation process following IEEE 802.3
standard will be triggered and will result in RGMII-to-RGMII signal
failure on the interface because VPHY will try to poll the PHY status
that is not available in the scenario of RGMII-to-RGMII connection
(normally the link partner is usually an external processor).
Note that when VPHY fails on accessing PHY registers, it will fall back
to 100Mbps speed, it indicates disabling VPHY is optional if you only
need the port to link at 100Mbps speed.
Again, VPHY must and can only be disabled by writing VPHY_DISABLE bit in
the register below as there is no strapping pin for the control."
This patch was tested on LAN9372, so far it seems to not to affect VPHY
based clock crossing optimization for the ports with integrated PHYs.
[1]: https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
interfaces
This driver do not support in-band mode and in case of CPU<->Switch
link, this mode is not working any way. So, disable it otherwise ingress
path of the switch MAC will stay disabled.
Note: lan9372 manual do not document 0xN301 BIT(2) for the RGMII mode
and recommend[1] to disable in-band link status update for the RGMII RX
path by clearing 0xN302 BIT(0). But, 0xN301 BIT(2) seems to work too, so
keep it unified with other KSZ switches.
[1] https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the LAN9371 and LAN9372, the 4th internal PHY is a 100BaseTX PHY
instead of a 100BaseT1 PHY. The 100BaseTX PHYs have a different base
register offset.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a050 ("ionic: fix kernel panic due to multi-buffer handling")
d9c04209990b ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For mlxsw
Reviewed-by: Kory Maincent <Kory.maincent@bootlin.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> # for mctp-i2c
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240625083853.2205977-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd6183 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ9477 allows HSR in-HW offloading for any of two selected ports.
This patch adds check if one tries to use more than two ports with
HSR offloading enabled.
The problem is with RedBox configuration (HSR-SAN) - when configuring:
ip link add name hsr0 type hsr slave1 lan1 slave2 lan2 interlink lan3 \
supervision 45 version 1
The lan1 (port0) and lan2 (port1) are correctly configured as ports, which
can use HSR offloading on ksz9477.
However, when we do already have two bits set in hsr_ports, we need to
return (-ENOTSUPP), so the interlink port (lan3) would be used with
SW based HSR RedBox support.
Otherwise, I do see some strange network behavior, as some HSR frames are
visible on non-HSR network and vice versa.
This causes the switch connected to interlink port (lan3) to drop frames
and no communication is possible.
Moreover, conceptually - the interlink (i.e. HSR-SAN port - lan3/port2)
shall be only supported in software as it is also possible to use ksz9477
with only SW based HSR (i.e. port0/1 -> hsr0 with offloading, port2 ->
HSR-SAN/interlink, port4/5 -> hsr1 with SW based HSR).
Fixes: 5055cccfc2d1 ("net: hsr: Provide RedBox support (HSR-SAN)")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver should return RMII interface when XMII is running in RMII mode.
Fixes: 0ab7f6bf1675 ("net: dsa: microchip: ksz9477: use common xmii function")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Acked-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1716932066-3342-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adjust the initialization sequence of KSZ88x3 switches to enable
802.1p priority control on Port 2 before configuring Port 1. This
change ensures the apptrust functionality on Port 1 operates
correctly, as it depends on the priority settings of Port 2. The
prior initialization sequence incorrectly configured Port 1 first,
which could lead to functional discrepancies.
Fixes: a1ea57710c9d ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240517050121.2174412-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before DCB support, the KSZ driver had only PCP as source of packet
priority values. To avoid regressions, make PCP only as default value.
User will need enable DSCP support manually.
This patch do not affect other KSZ8 related quirks. User will still be
warned by setting not support configurations for the port 2.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All other functions are commented. Add missing comments to following
functions:
ksz_set_global_dscp_entry()
ksz_port_add_dscp_prio()
ksz_port_del_dscp_prio()
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPV is added and used term in 802.1Qci PSFP and merged into 802.1Q (from
802.1Q-2018) for another functions.
Even it does similar operation holding temporal priority value
internally (as it is named), because KSZ datasheet doesn't use the term
of IPV (Internal Priority Value) and avoiding any confusion later when
PSFP is in the Linux world, it is better to rename IPV to IPM (Internal
Priority Mapping).
In addition, LAN937x documentation already use IPV for 802.1Qci PSFP
related functionality.
Suggested-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509065023.3033397-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8xxx variants
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches have different behavior on different ports:
- It seems to be not possible to disable VLAN PCP classification on port
2. It means, as soon as mutliqueue support is enabled, frames with
VLAN tag will get PCP prios. This behavior do not affect Port 1 -
it is possible to disable PCP prios.
- DSCP classification is not working on Port 2.
Since there are still usable configuration combinations, I added some
quirks to make sure user will get appropriate error message if not
possible configuration is chosen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
