summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath10k
AgeCommit message (Collapse)Author
2024-11-13Merge tag 'wireless-next-2024-11-13' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.13 Most likely the last -next pull request for v6.13. Most changes are in Realtek and Qualcomm drivers, otherwise not really anything noteworthy. Major changes: mac80211 * EHT 1024 aggregation size for transmissions ath12k * switch to using wiphy_lock() and remove ar->conf_mutex * firmware coredump collection support * add debugfs support for a multitude of statistics ath11k * dt: document WCN6855 hardware inputs ath9k * remove include/linux/ath9k_platform.h ath5k * Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support rtw88: * 8821au and 8812au USB adapters support rtw89 * thermal protection * firmware secure boot for WiFi 6 chip * tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (154 commits) Revert "wifi: iwlegacy: do not skip frames with bad FCS" wifi: mac80211: pass MBSSID config by reference wifi: mac80211: Support EHT 1024 aggregation size in TX net: rfkill: gpio: Add check for clk_enable() wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw() wifi: Switch back to struct platform_driver::remove() wifi: ipw2x00: libipw_rx_any(): fix bad alignment wifi: brcmfmac: release 'root' node in all execution paths wifi: iwlwifi: mvm: don't call power_update_mac in fast suspend wifi: iwlwifi: s/IWL_MVM_INVALID_STA/IWL_INVALID_STA wifi: iwlwifi: bump minimum API version in BZ/SC to 92 wifi: iwlwifi: move IWL_LMAC_*_INDEX to fw/api/context.h wifi: iwlwifi: be less noisy if the NIC is dead in S3 wifi: iwlwifi: mvm: tell iwlmei when we finished suspending wifi: iwlwifi: allow fast resume on ax200 wifi: iwlwifi: mvm: support new initiator and responder command version wifi: iwlwifi: mvm: use wiphy locked debugfs for low-latency wifi: iwlwifi: mvm: MLO scan upon channel condition degradation wifi: iwlwifi: mvm: support new versions of the wowlan APIs wifi: iwlwifi: mvm: allow always calling iwl_mvm_get_bss_vif() ... ==================== Link: https://patch.msgid.link/20241113172918.A8A11C4CEC3@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-11wifi: Switch back to struct platform_driver::remove()Uwe Kleine-König
After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all platform drivers below drivers/net/wireless to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. En passant several whitespace changes are done to make indentation consistent in the struct initializers. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Acked-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241106170706.38922-2-u.kleine-koenig@baylibre.com
2024-10-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR (net-6.12-rc6). Conflicts: drivers/net/wireless/intel/iwlwifi/mvm/mld-mac80211.c cbe84e9ad5e2 ("wifi: iwlwifi: mvm: really send iwl_txpower_constraints_cmd") 188a1bf89432 ("wifi: mac80211: re-order assigning channel in activate links") https://lore.kernel.org/all/20241028123621.7bbb131b@canb.auug.org.au/ net/mac80211/cfg.c c4382d5ca1af ("wifi: mac80211: update the right link for tx power") 8dd0498983ee ("wifi: mac80211: Fix setting txpower with emulate_chanctx") drivers/net/ethernet/intel/ice/ice_ptp_hw.h 6e58c3310622 ("ice: fix crash on probe for DPLL enabled E810 LOM") e4291b64e118 ("ice: Align E810T GPIO to other products") ebb2693f8fbd ("ice: Read SDP section from NVM for pin definitions") ac532f4f4251 ("ice: Cleanup unused declarations") https://lore.kernel.org/all/20241030120524.1ee1af18@canb.auug.org.au/ No adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-31Merge tag 'ath-next-20241030' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath ath.git patches for v6.13 This development cycle featured phase 1 of patches to ath12k to support the new 802.11be MLO feature, along with other ath12k feature patches. In older drivers, support for some additional devices were added. And there was the usual set of bug fixes and cleanups across most drivers. Per-driver highlights: ath12k * Switch to using wiphy_lock() and remove ar->conf_mutex * Convert struct ath12k_sta::update_wk to use struct wiphy_work * Add phase 1 of 802.11be MLO support * Add firmware coredump collection support * Add debugfs support for a multitude of statistics * Fix host representation of multiple hal_rx structs * Fix use-after-free in ath12k_dp_cc_cleanup() * Skip Rx TID cleanup for self peer * Fix warning and crash when unloading in a VM * Convert CE interrupt handling from tasklet to BH workqueue * Fix A-MSDU indication in monitor mode ath11k * Fix double free issue during SRNG deinit * Enable firmware diagnostic events for WCN6750 * Fix CE offset address calculation for WCN6750 during SSR * Fix stack frame size warning in ath11k_vif_wow_set_wakeups() * Document the inputs for ath11k on WCN6855 ath10k * Fix multiple stack frame size warnings * Fix invalid VHT parameters in supported_vht_mcs_rate_nss* structs * Avoid NULL pointer error during SDIO remove ath5k * Add support for Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A
2024-10-23wifi: mac80211: call rate_control_rate_update() for link STAJohannes Berg
In order to update the right link information, call the update rate_control_rate_update() with the right link_sta, and then pass that through to the driver's sta_rc_update() method. The software rate control still doesn't support it, but that'll be skipped by not having a rate control ref. Since it now operates on a link sta, rename the driver method. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20241007144851.5851b6b5fd41.Ibdf50d96afa4b761dd9b9dfd54a1147e77a75329@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-10-17Merge tag 'ath-current-20241016' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath ath.git patches for v6.12-rc4 Fix two instances of memory leaks, one in ath10k and one in ath11k.
2024-10-16wifi: ath10k: avoid NULL pointer error during sdio removeKang Yang
When running 'rmmod ath10k', ath10k_sdio_remove() will free sdio workqueue by destroy_workqueue(). But if CONFIG_INIT_ON_FREE_DEFAULT_ON is set to yes, kernel panic will happen: Call trace: destroy_workqueue+0x1c/0x258 ath10k_sdio_remove+0x84/0x94 sdio_bus_remove+0x50/0x16c device_release_driver_internal+0x188/0x25c device_driver_detach+0x20/0x2c This is because during 'rmmod ath10k', ath10k_sdio_remove() will call ath10k_core_destroy() before destroy_workqueue(). wiphy_dev_release() will finally be called in ath10k_core_destroy(). This function will free struct cfg80211_registered_device *rdev and all its members, including wiphy, dev and the pointer of sdio workqueue. Then the pointer of sdio workqueue will be set to NULL due to CONFIG_INIT_ON_FREE_DEFAULT_ON. After device release, destroy_workqueue() will use NULL pointer then the kernel panic happen. Call trace: ath10k_sdio_remove ->ath10k_core_unregister …… ->ath10k_core_stop ->ath10k_hif_stop ->ath10k_sdio_irq_disable ->ath10k_hif_power_down ->del_timer_sync(&ar_sdio->sleep_timer) ->ath10k_core_destroy ->ath10k_mac_destroy ->ieee80211_free_hw ->wiphy_free …… ->wiphy_dev_release ->destroy_workqueue Need to call destroy_workqueue() before ath10k_core_destroy(), free the work queue buffer first and then free pointer of work queue by ath10k_core_destroy(). This order matches the error path order in ath10k_sdio_probe(). No work will be queued on sdio workqueue between it is destroyed and ath10k_core_destroy() is called. Based on the call_stack above, the reason is: Only ath10k_sdio_sleep_timer_handler(), ath10k_sdio_hif_tx_sg() and ath10k_sdio_irq_disable() will queue work on sdio workqueue. Sleep timer will be deleted before ath10k_core_destroy() in ath10k_hif_power_down(). ath10k_sdio_irq_disable() only be called in ath10k_hif_stop(). ath10k_core_unregister() will call ath10k_hif_power_down() to stop hif bus, so ath10k_sdio_hif_tx_sg() won't be called anymore. Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189 Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Tested-by: David Ruth <druth@chromium.org> Reviewed-by: David Ruth <druth@chromium.org> Link: https://patch.msgid.link/20241008022246.1010-1-quic_kangyang@quicinc.com Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
2024-10-16wifi: ath10k: Fix memory leak in management txManikanta Pubbisetty
In the current logic, memory is allocated for storing the MSDU context during management packet TX but this memory is not being freed during management TX completion. Similar leaks are seen in the management TX cleanup logic. Kmemleak reports this problem as below, unreferenced object 0xffffff80b64ed250 (size 16): comm "kworker/u16:7", pid 148, jiffies 4294687130 (age 714.199s) hex dump (first 16 bytes): 00 2b d8 d8 80 ff ff ff c4 74 e9 fd 07 00 00 00 .+.......t...... backtrace: [<ffffffe6e7b245dc>] __kmem_cache_alloc_node+0x1e4/0x2d8 [<ffffffe6e7adde88>] kmalloc_trace+0x48/0x110 [<ffffffe6bbd765fc>] ath10k_wmi_tlv_op_gen_mgmt_tx_send+0xd4/0x1d8 [ath10k_core] [<ffffffe6bbd3eed4>] ath10k_mgmt_over_wmi_tx_work+0x134/0x298 [ath10k_core] [<ffffffe6e78d5974>] process_scheduled_works+0x1ac/0x400 [<ffffffe6e78d60b8>] worker_thread+0x208/0x328 [<ffffffe6e78dc890>] kthread+0x100/0x1c0 [<ffffffe6e78166c0>] ret_from_fork+0x10/0x20 Free the memory during completion and cleanup to fix the leak. Protect the mgmt_pending_tx idr_remove() operation in ath10k_wmi_tlv_op_cleanup_mgmt_tx_send() using ar->data_lock similar to other instances. Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 Fixes: dc405152bb64 ("ath10k: handle mgmt tx completion event") Fixes: c730c477176a ("ath10k: Remove msdu from idr when management pkt send fails") Cc: stable@vger.kernel.org Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Link: https://patch.msgid.link/20241015064103.6060-1-quic_mpubbise@quicinc.com Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
2024-09-28wifi: ath10k: fix the stack frame size warning in ath10k_hw_scanMiaoqing Pan
Fix the following W=1 kernel build warning: drivers/net/wireless/ath/ath10k/mac.c: In function ‘ath10k_hw_scan’: drivers/net/wireless/ath/ath10k/mac.c:6468:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=] Compile tested only. Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240830015649.1083758-1-quic_miaoqing@quicinc.com
2024-09-28wifi: ath10k: fix the stack frame size warning in ath10k_remain_on_channelMiaoqing Pan
Fix the following W=1 kernel build warning: drivers/net/wireless/ath/ath10k/mac.c: In function ‘ath10k_remain_on_channel’: drivers/net/wireless/ath/ath10k/mac.c:7980:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=] Compile tested only. Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240830015349.1083226-1-quic_miaoqing@quicinc.com
2024-09-28wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss2Baochen Qiang
In supported_vht_mcs_rate_nss2, the rate for MCS9 & VHT20 is defined as {1560, 1733}, this does not align with firmware's definition and therefore fails the verification in ath10k_mac_get_rate_flags_vht(): invalid vht params rate 1730 100kbps nss 2 mcs 9 and: invalid vht params rate 1920 100kbps nss 2 mcs 9 Change it to {1730, 1920} to align with firmware to fix the issue. Since ath10k_hw_params::supports_peer_stats_info is enabled only for QCA6174, this change does not affect other chips. Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00309-QCARMSWPZ-1 Fixes: 3344b99d69ab ("ath10k: add bitrate parse for peer stats info") Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Closes: https://lore.kernel.org/lkml/fba24cd3-4a1e-4072-8585-8402272788ff@molgen.mpg.de/ Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> # Dell XPS 13 9360 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240711020344.98040-3-quic_bqiang@quicinc.com
2024-09-28wifi: ath10k: fix invalid VHT parameters in supported_vht_mcs_rate_nss1Baochen Qiang
In supported_vht_mcs_rate_nss1, the rate for MCS9 & VHT20 is defined as {780, 867}, this does not align with firmware's definition and therefore fails the verification in ath10k_mac_get_rate_flags_vht(): invalid vht params rate 960 100kbps nss 1 mcs 9 Change it to {865, 960} to align with firmware, so this issue could be fixed. Since ath10k_hw_params::supports_peer_stats_info is enabled only for QCA6174, this change does not affect other chips. Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00309-QCARMSWPZ-1 Fixes: 3344b99d69ab ("ath10k: add bitrate parse for peer stats info") Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Closes: https://lore.kernel.org/lkml/fba24cd3-4a1e-4072-8585-8402272788ff@molgen.mpg.de/ Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240711020344.98040-2-quic_bqiang@quicinc.com
2024-09-06wifi: mac80211: handle ieee80211_radar_detected() for MLOAditya Kumar Singh
Currently DFS works under assumption there could be only one channel context in the hardware. Hence, drivers just calls the function ieee80211_radar_detected() passing the hardware structure. However, with MLO, this obviously will not work since number of channel contexts will be more than one and hence drivers would need to pass the channel information as well on which the radar is detected. Also, when radar is detected in one of the links, other link's CAC should not be cancelled. Hence, in order to support DFS with MLO, do the following changes - * Add channel context conf pointer as an argument to the function ieee80211_radar_detected(). During MLO, drivers would have to pass on which channel context conf radar is detected. Otherwise, drivers could just pass NULL. * ieee80211_radar_detected() will iterate over all channel contexts present and * if channel context conf is passed, only mark that as radar detected * if NULL is passed, then mark all channel contexts as radar detected * Then as usual, schedule the radar detected work. * In the worker, go over all the contexts again and for all such context which is marked with radar detected, cancel the ongoing CAC by calling ieee80211_dfs_cac_cancel() and then notify cfg80211 via cfg80211_radar_event(). * To cancel the CAC, pass the channel context as well where radar is detected to ieee80211_dfs_cac_cancel(). This ensures that CAC is canceled only on the links using the provided context, leaving other links unaffected. This would also help in scenarios where there is split phy 5 GHz radio, which is capable of DFS channels in both lower and upper band. In this case, simultaneous radars can be detected. Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20240906064426.2101315-9-quic_adisi@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-07-19Merge tag 'iommu-updates-v6.11' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux Pull iommu updates from Will Deacon: "Core: - Support for the "ats-supported" device-tree property - Removal of the 'ops' field from 'struct iommu_fwspec' - Introduction of iommu_paging_domain_alloc() and partial conversion of existing users - Introduce 'struct iommu_attach_handle' and provide corresponding IOMMU interfaces which will be used by the IOMMUFD subsystem - Remove stale documentation - Add missing MODULE_DESCRIPTION() macro - Misc cleanups Allwinner Sun50i: - Ensure bypass mode is disabled on H616 SoCs - Ensure page-tables are allocated below 4GiB for the 32-bit page-table walker - Add new device-tree compatible strings AMD Vi: - Use try_cmpxchg64() instead of cmpxchg64() when updating pte Arm SMMUv2: - Print much more useful information on context faults - Fix Qualcomm TBU probing when CONFIG_ARM_SMMU_QCOM_DEBUG=n - Add new Qualcomm device-tree bindings Arm SMMUv3: - Support for hardware update of access/dirty bits and reporting via IOMMUFD - More driver rework from Jason, this time updating the PASID/SVA support to prepare for full IOMMUFD support - Add missing MODULE_DESCRIPTION() macro - Minor fixes and cleanups NVIDIA Tegra: - Fix for benign fwspec initialisation issue exposed by rework on the core branch Intel VT-d: - Use try_cmpxchg64() instead of cmpxchg64() when updating pte - Use READ_ONCE() to read volatile descriptor status - Remove support for handling Execute-Requested requests - Avoid calling iommu_domain_alloc() - Minor fixes and refactoring Qualcomm MSM: - Updates to the device-tree bindings" * tag 'iommu-updates-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (72 commits) iommu/tegra-smmu: Pass correct fwnode to iommu_fwspec_init() iommu/vt-d: Fix identity map bounds in si_domain_init() iommu: Move IOMMU_DIRTY_NO_CLEAR define dt-bindings: iommu: Convert msm,iommu-v0 to yaml iommu/vt-d: Fix aligned pages in calculate_psi_aligned_address() iommu/vt-d: Limit max address mask to MAX_AGAW_PFN_WIDTH docs: iommu: Remove outdated Documentation/userspace-api/iommu.rst arm64: dts: fvp: Enable PCIe ATS for Base RevC FVP iommu/of: Support ats-supported device-tree property dt-bindings: PCI: generic: Add ats-supported property iommu: Remove iommu_fwspec ops OF: Simplify of_iommu_configure() ACPI: Retire acpi_iommu_fwspec_ops() iommu: Resolve fwspec ops automatically iommu/mediatek-v1: Clean up redundant fwspec checks RDMA/usnic: Use iommu_paging_domain_alloc() wifi: ath11k: Use iommu_paging_domain_alloc() wifi: ath10k: Use iommu_paging_domain_alloc() drm/msm: Use iommu_paging_domain_alloc() vhost-vdpa: Use iommu_paging_domain_alloc() ...
2024-07-04wifi: ath10k: Use iommu_paging_domain_alloc()Lu Baolu
An iommu domain is allocated in ath10k_fw_init() and is attached to ar_snoc->fw.dev in the same function. Use iommu_paging_domain_alloc() to make it explicit. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/20240610085555.88197-11-baolu.lu@linux.intel.com Signed-off-by: Will Deacon <will@kernel.org>
2024-06-26wifi: mac80211: inform the low level if drv_stop() is a suspendEmmanuel Grumbach
This will allow the low level driver to take different actions for different flows. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240618192529.739036208b6e.Ie18a2fe8e02bf2717549d39420b350cfdaf3d317@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-06-10Merge tag 'wireless-next-2024-06-07' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.11 The first "new features" pull request for v6.11 with changes both in stack and in drivers. Nothing out of ordinary, except that we have two conflicts this time: net/mac80211/cfg.c https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au drivers/net/wireless/microchip/wilc1000/netdev.c https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au Major changes: cfg80211/mac80211 * parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers wilc1000 * read MAC address during probe to make it visible to user space iwlwifi * bump FW API to 91 for BZ/SC devices * report 64-bit radiotap timestamp * enable P2P low latency by default * handle Transmit Power Envelope (TPE) advertised by AP * start using guard() rtlwifi * RTL8192DU support ath12k * remove unsupported tx monitor handling * channel 2 in 6 GHz band support * Spatial Multiplexing Power Save (SMPS) in 6 GHz band support * multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support * dynamic VLAN support * add panic handler for resetting the firmware state ath10k * add qcom,no-msa-ready-indicator Device Tree property * LED support for various chipsets * tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits) wifi: ath12k: add hw_link_id in ath12k_pdev wifi: ath12k: add panic handler wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity() wifi: brcm80211: remove unused structs wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type) wifi: ath12k: do not process consecutive RDDM event dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup() wifi: rtlwifi: handle return value of usb init TX/RX wifi: rtlwifi: Enable the new rtl8192du driver wifi: rtlwifi: Add rtl8192du/sw.c wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg wifi: rtlwifi: Add rtl8192du/dm.{c,h} wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h} wifi: rtlwifi: Add rtl8192du/rf.{c,h} wifi: rtlwifi: Add rtl8192du/trx.{c,h} wifi: rtlwifi: Add rtl8192du/phy.{c,h} wifi: rtlwifi: Add rtl8192du/hw.{c,h} wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU wifi: rtlwifi: Add rtl8192du/table.{c,h} ... Signed-off-by: Jakub Kicinski <kuba@kernel.org> ==================== Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-06-01Merge tag 'ath-current-20240531' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath Merge ath-current from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git ath.git fixes for 6.10. Two fixes for user reported regressions in ath11k. One dependency fix and one error path fix.
2024-05-22tracing/treewide: Remove second parameter of __assign_str()Steven Rostedt (Google)
With the rework of how the __string() handles dynamic strings where it saves off the source string in field in the helper structure[1], the assignment of that value to the trace event field is stored in the helper value and does not need to be passed in again. This means that with: __string(field, mystring) Which use to be assigned with __assign_str(field, mystring), no longer needs the second parameter and it is unused. With this, __assign_str() will now only get a single parameter. There's over 700 users of __assign_str() and because coccinelle does not handle the TRACE_EVENT() macro I ended up using the following sed script: git grep -l __assign_str | while read a ; do sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file; mv /tmp/test-file $a; done I then searched for __assign_str() that did not end with ';' as those were multi line assignments that the sed script above would fail to catch. Note, the same updates will need to be done for: __assign_str_len() __assign_rel_str() __assign_rel_str_len() I tested this with both an allmodconfig and an allyesconfig (build only for both). [1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/ Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts. Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs Tested-by: Guenter Roeck <linux@roeck-us.net>
2024-05-21Merge tag 'pci-v6.10-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull pci updates from Bjorn Helgaas: "Enumeration: - Skip E820 checks for MCFG ECAM regions for new (2016+) machines, since there's no requirement to describe them in E820 and some platforms require ECAM to work (Bjorn Helgaas) - Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien Le Moal) - Remove last user and pci_enable_device_io() (Heiner Kallweit) - Wait for Link Training==0 to avoid possible race (Ilpo Järvinen) - Skip waiting for devices that have been disconnected while suspended (Ilpo Järvinen) - Clear Secondary Status errors after enumeration since Master Aborts and Unsupported Request errors are an expected part of enumeration (Vidya Sagar) MSI: - Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas) Error handling: - Mask Genesys GL975x SD host controller Replay Timer Timeout correctable errors caused by a hardware defect; the errors cause interrupts that prevent system suspend (Kai-Heng Feng) - Fix EDR-related _DSM support, which previously evaluated revision 5 but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan) ASPM: - Simplify link state definitions and mask calculation (Ilpo Järvinen) Power management: - Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS apparently doesn't know how to put them back in D0 (Mario Limonciello) CXL: - Support resetting CXL devices; special handling required because CXL Ports mask Secondary Bus Reset by default (Dave Jiang) DOE: - Support DOE Discovery Version 2 (Alexey Kardashevskiy) Endpoint framework: - Set endpoint BAR to be 64-bit if the driver says that's all the device supports, in addition to doing so if the size is >2GB (Niklas Cassel) - Simplify endpoint BAR allocation and setting interfaces (Niklas Cassel) Cadence PCIe controller driver: - Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof Kozlowski) Cadence PCIe endpoint driver: - Configure endpoint BARs to be 64-bit based on the BAR type, not the BAR value (Niklas Cassel) Freescale Layerscape PCIe controller driver: - Convert DT binding to YAML (Frank Li) MediaTek MT7621 PCIe controller driver: - Add DT binding missing 'reg' property for child Root Ports (Krzysztof Kozlowski) - Fix theoretical string truncation in PHY name (Sergio Paracuellos) NVIDIA Tegra194 PCIe controller driver: - Return success for endpoint probe instead of falling through to the failure path (Vidya Sagar) Renesas R-Car PCIe controller driver: - Add DT binding missing IOMMU properties (Geert Uytterhoeven) - Add DT binding R-Car V4H compatible for host and endpoint mode (Yoshihiro Shimoda) Rockchip PCIe controller driver: - Configure endpoint BARs to be 64-bit based on the BAR type, not the BAR value (Niklas Cassel) - Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski) - Set the Subsystem Vendor ID, which was previously zero because it was masked incorrectly (Rick Wertenbroek) Synopsys DesignWare PCIe controller driver: - Restructure DBI register access to accommodate devices where this requires Refclk to be active (Manivannan Sadhasivam) - Remove the deinit() callback, which was only need by the pcie-rcar-gen4, and do it directly in that driver (Manivannan Sadhasivam) - Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean up things like eDMA (Manivannan Sadhasivam) - Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel to dw_pcie_ep_init() (Manivannan Sadhasivam) - Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to reflect the actual functionality (Manivannan Sadhasivam) - Call dw_pcie_ep_init_registers() directly from all the glue drivers, not just those that require active Refclk from the host (Manivannan Sadhasivam) - Remove the "core_init_notifier" flag, which was an obscure way for glue drivers to indicate that they depend on Refclk from the host (Manivannan Sadhasivam) TI J721E PCIe driver: - Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli) - Add DT binding J722S SoC support (Siddharth Vadapalli) TI Keystone PCIe controller driver: - Add DT binding missing num-viewport, phys and phy-name properties (Jan Kiszka) Miscellaneous: - Constify and annotate with __ro_after_init (Heiner Kallweit) - Convert DT bindings to YAML (Krzysztof Kozlowski) - Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming Zhou)" * tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits) PCI: Do not wait for disconnected devices when resuming x86/pci: Skip early E820 check for ECAM region PCI: Remove unused pci_enable_device_io() ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io() PCI: Update pci_find_capability() stub return types PCI: Remove PCI_IRQ_LEGACY scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios Revert "genirq/msi: Provide constants for PCI/IMS support" Revert "x86/apic/msi: Enable PCI/IMS" Revert "iommu/vt-d: Enable PCI/IMS" Revert "iommu/amd: Enable PCI/IMS" Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support" ...
2024-05-20wifi: ath10k: fix QCOM_RPROC_COMMON dependencyDmitry Baryshkov
If ath10k_snoc is built-in, while Qualcomm remoteprocs are built as modules, compilation fails with: /usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_init': drivers/net/wireless/ath/ath10k/snoc.c:1534: undefined reference to `qcom_register_ssr_notifier' /usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/ath/ath10k/snoc.o: in function `ath10k_modem_deinit': drivers/net/wireless/ath/ath10k/snoc.c:1551: undefined reference to `qcom_unregister_ssr_notifier' Add corresponding dependency to ATH10K_SNOC Kconfig entry so that it's built as module if QCOM_RPROC_COMMON is built as module too. Fixes: 747ff7d3d742 ("ath10k: Don't always treat modem stop events as crashes") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240511-ath10k-snoc-dep-v1-1-9666e3af5c27@linaro.org
2024-05-16Merge tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds
Pull MMC updates from Ulf Hansson: "MMC core: - Increase the timeout period of the ACMD41 command - Add card entry for quirks to debugfs - Add mmc_gpiod_set_cd_config() function - Store owner from SDIO modules with sdio_register_driver() MMC host: - atmel-mci: Some cleanups and a switch to use dev_err_probe() - renesas_sdhi: - Add support for RZ/G2L, RZ/G3S and RZ/V2M variants - Set the SDBUF after reset - sdhci: Add support for "Tuning Error" interrupts - sdhci-acpi: - Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA - Disable write protect detection on Toshiba WT10-A - Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working - sdhci_am654: - Re-work and fix the tuning support for multiple speed-modes - Add tuning algorithm for delay chain - sdhci-esdhc-imx: Add NXP S32G3 support - sdhci-of-dwcmshc: - Add tuning support for Sophgo CV1800B and SG200X - Implement SDHCI CQE support - sdhci-pci-gli: Use the proper pci_set_power_state() instead of PMCSR writes" MEMSTICK: - Convert a couple of drivers to use the ->remove_new() callback" * tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits) mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list mmc: renesas_sdhi: Set the SDBUF after reset mmc: core: Increase the timeout period of the ACMD41 command mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too mmc: atmel-mci: Switch to use dev_err_probe() mmc: atmel-mci: Incapsulate used to be a platform data into host structure mmc: atmel-mci: Replace platform device pointer by generic one mmc: atmel-mci: Use temporary variable for struct device mmc: atmel-mci: Get rid of platform data leftovers mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning mmc: sdhci-s3c: Choose sdhci_ops based on variant mmc: sdhci_am654: Constify struct sdhci_ops mmc: sdhci-sprd: Constify struct sdhci_ops mmc: sdhci-omap: Constify struct sdhci_ops mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops mmc: slot-gpio: Use irq_handler_t type mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA ...
2024-05-15wifi: ath10k: add LED and GPIO controlling support for various chipsetsSebastian Gottschall
Adds LED and GPIO Control support for 988x, 9887, 9888, 99x0, 9984 based chipsets with on chipset connected led's using WMI Firmware API. The LED device will get available named as "ath10k-phyX" at sysfs and can be controlled with various triggers. Adds also debugfs interface for gpio control. Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Reviewed-by: Steve deRosier <derosier@cal-sierra.com> [kvalo: major reorg and cleanup] Signed-off-by: Kalle Valo <kvalo@codeaurora.org> [ansuel: rebase and small cleanup] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20230611080505.17393-1-ansuelsmth@gmail.com
2024-05-13wifi: ath10k: do not always wait for MSA_READY indicatorMarc Gonzalez
The ath10k driver waits for an "MSA_READY" indicator to complete initialization. If the indicator is not received, then the device remains unusable. Several msm8998-based devices are affected by this issue. Oddly, it seems safe to NOT wait for the indicator, and proceed immediately when QMI_EVENT_SERVER_ARRIVE. fw_version 0x100204b2 fw_build_timestamp 2019-09-04 03:01 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.1.0-01202-QCAHLSWMTPLZ-1.221523.2 Jeff Johnson wrote: The feedback I received was "it might be ok to change all ath10k qmi to skip waiting for msa_ready", and it was pointed out that ath11k (and ath12k) do not wait for it. However with so many deployed devices, "might be ok" isn't a strong argument for changing the default behavior. Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr> Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/23540303-5816-45d5-a1af-5f09d645a73b@freebox.fr
2024-05-03Merge tag 'ath-next-20240502' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath ath.git patches for v6.10 ath12k * debugfs support * dfs_simulate_radar debugfs file * disable Wireless Extensions * suspend and hibernation support * ACPI support * refactoring in preparation of multi-link support ath11k * support hibernation (required changes in qrtr and MHI subsystems) * ieee80211-freq-limit Device Tree property support ath10k * firmware-name Device Tree property support
2024-04-25wifi: ath10k: Refer to INTX instead of LEGACYDamien Le Moal
To be consistent with the deprecation of PCI_IRQ_LEGACY and its replacement with PCI_IRQ_INTX, rename macros and functions referencing "legacy irq" to instead use the term "intx irq". Link: https://lore.kernel.org/r/20240325070944.3600338-20-dlemoal@kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2024-04-25wifi: ath10k: drop fw.eboard file nameDmitry Baryshkov
Follow the example set up by previous commit and drop .fw.eboard setting. Instead always use "eboard.bin" in this case. QCA9984 already uses that file name, any (im)possible future users will just have to use the same file name. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240130-wcn3990-board-fw-v1-3-738f7c19a8c8@linaro.org
2024-04-25wifi: ath10k: drop chip-specific board data file nameDmitry Baryshkov
The .fw.board parameter predates board-2.bin support. For all the platforms, which define this parameter, it is equal to "board.bin". Other platforms (like WCN3990) ommit it, limiting the ability to provide board-specific data file. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240130-wcn3990-board-fw-v1-2-738f7c19a8c8@linaro.org
2024-04-25wifi: ath10k: populate board data for WCN3990Dmitry Baryshkov
Specify board data size (and board.bin filename) for the WCN3990 platform. Reported-by: Yongqin Liu <yongqin.liu@linaro.org> Fixes: 03a72288c546 ("ath10k: wmi: add hw params entry for wcn3990") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240130-wcn3990-board-fw-v1-1-738f7c19a8c8@linaro.org
2024-04-24wifi: ath10k: Fix an error code problem in ↵Su Hui
ath10k_dbg_sta_write_peer_debug_trigger() Clang Static Checker (scan-build) warns: drivers/net/wireless/ath/ath10k/debugfs_sta.c:line 429, column 3 Value stored to 'ret' is never read. Return 'ret' rather than 'count' when 'ret' stores an error code. Fixes: ee8b08a1be82 ("ath10k: add debugfs support to get per peer tids log via tracing") Signed-off-by: Su Hui <suhui@nfschina.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422034243.938962-1-suhui@nfschina.com
2024-04-24wifi: ath10k: allocate dummy net_device dynamicallyBreno Leitao
Embedding net_device into structures prohibits the usage of flexible arrays in the net_device structure. For more details, see the discussion at [1]. Un-embed the net_device from struct ath10k by converting it into a pointer. Then use the leverage alloc_netdev() to allocate the net_device object at ath10k_core_create(). The free of the device occurs at ath10k_core_destroy(). [1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/ Signed-off-by: Breno Leitao <leitao@debian.org> Acked-by: Kalle Valo <kvalo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-04-05wifi: ath10k: support board-specific firmware overridesDmitry Baryshkov
Different Qualcomm platforms using WCN3990 WiFI chip use SoC-specific firmware versions with different features. For example firmware for SDM845 doesn't use single-chan-info-per-channel feature, while firmware for QRB2210 / QRB4210 requires that feature. Allow board DT files to override the subdir of the fw dir used to lookup the firmware-N.bin file decribing corresponding WiFi firmware. For example: - ath10k/WCN3990/hw1.0/wlanmdsp.mbn, ath10k/WCN3990/hw1.0/firmware-5.bin: main firmware files, used by default - ath10k/WCN3990/hw1.0/qcm2290/wlanmdsp.mbn, ath10k/WCN3990/hw1.0/qcm2290/firmware-5.bin: SoC specific firmware with different signature and feature bits Note, while board files lookup uses the same function and thus it is possible to provide board-specific board-2.bin files, this is not required in 99% of cases as board-2.bin already contains a way to provide board-specific data with finer granularity than DT overrides. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240306-wcn3990-firmware-path-v2-2-f89e98e71a57@linaro.org
2024-04-04wifi: ath10k: sdio: drop driver owner initializationKrzysztof Kozlowski
Core in sdio_register_driver() already sets the .owner, so driver does not need to. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-4-ae46d6b955eb@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-04-04wifi: ath10k: sdio: simplify module initializationKrzysztof Kozlowski
This driver's initialization functions do not perform any custom code, except printing messages. Printing messages on modules loading/unloading is discouraged because it pollutes the dmesg regardless whether user actually has this device. Core kernel code already gives tools to investigate whether module was loaded or not. Drop the printing messages which allows to replace open-coded module_sdio_driver(). Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240403-module-owner-sdio-v2-3-ae46d6b955eb@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-03-25wifi: ath: Convert sprintf/snprintf to sysfs_emitLi Zhijian
Per filesystems/sysfs.rst, show() should only use sysfs_emit() or sysfs_emit_at() when formatting the value to be returned to user space. coccinelle complains that there are still a couple of functions that use snprintf(). Convert them to sysfs_emit(). sprintf() will be converted as weel if they have. Generally, this patch is generated by make coccicheck M=<path/to/file> MODE=patch \ COCCI=scripts/coccinelle/api/device_attr_show.cocci No functional change intended CC: Kalle Valo <kvalo@kernel.org> CC: Jeff Johnson <jjohnson@kernel.org> CC: linux-wireless@vger.kernel.org CC: ath11k@lists.infradead.org CC: ath10k@lists.infradead.org Signed-off-by: Li Zhijian <lizhijian@fujitsu.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240315055211.1347548-1-lizhijian@fujitsu.com
2024-03-08wifi: ath10k: poll service ready message before failingBaochen Qiang
Currently host relies on CE interrupts to get notified that the service ready message is ready. This results in timeout issue if the interrupt is not fired, due to some unknown reasons. See below logs: [76321.937866] ath10k_pci 0000:02:00.0: wmi service ready event not received ... [76322.016738] ath10k_pci 0000:02:00.0: Could not init core: -110 And finally it causes WLAN interface bring up failure. Change to give it one more chance here by polling CE rings, before failing directly. Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00157-QCARMSWPZ-1 Fixes: 5e3dd157d7e7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices") Reported-by: James Prestwood <prestwoj@gmail.com> Tested-By: James Prestwood <prestwoj@gmail.com> # on QCA6174 hw3.2 Link: https://lore.kernel.org/linux-wireless/304ce305-fbe6-420e-ac2a-d61ae5e6ca1a@gmail.com/ Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240227030409.89702-1-quic_bqiang@quicinc.com
2024-02-21wifi: mac80211: check beacon countdown is complete on per link basisAditya Kumar Singh
Currently, function to check if beacon countdown is complete uses deflink to fetch the beacon and check the counter. However, with MLO, there is a need to check the counter for the beacon in a particular link. Add support to use link_id in order to fetch the beacon from a particular link data. Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://msgid.link/20240216144621.514385-2-quic_adisi@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-02-08wifi: mac80211: add support to call csa_finish on a linkAditya Kumar Singh
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a finalizing worker using the deflink. With MLO, there is a need to do it on a given link basis. Pass link ID of the link on which CSA needs to be finalized. Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-02-08wifi: mac80211: update beacon counters per link basisAditya Kumar Singh
Currently, function to update beacon counter uses deflink to fetch the beacon and then update the counter. However, with MLO, there is a need to update the counter for the beacon in a particular link. Add support to use link_id in order to fetch the beacon from a particular link data during beacon update counter. Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://msgid.link/20240130140918.1172387-3-quic_adisi@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2024-01-31Merge tag 'ath-next-20240130' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath ath.git patches for v6.9 We have new features for both ath11k and ath12k. ath12k is now under heavy refactoring in preparation for MLO support. Major changes: ath12k * refactoring in preparation for Multi-Link Operation (MLO) support * 1024 Block Ack window size support * provide firmware wmi logs via a trace event ath11k * 36 bit DMA mask support * support 6 GHz station power modes: Low Power Indoor (LPI), Standard Power) SP and Very Low Power (VLP)
2024-01-19wifi: ath10k: Fix enum ath10k_fw_crash_dump_type kernel-docJeff Johnson
The kernel-doc script currently reports: drivers/net/wireless/ath/ath10k/coredump.h:27: warning: Enum value 'ATH10K_FW_CRASH_DUMP_REGISTERS' not described in enum 'ath10k_fw_crash_dump_type' drivers/net/wireless/ath/ath10k/coredump.h:27: warning: Enum value 'ATH10K_FW_CRASH_DUMP_CE_DATA' not described in enum 'ath10k_fw_crash_dump_type' drivers/net/wireless/ath/ath10k/coredump.h:27: warning: Enum value 'ATH10K_FW_CRASH_DUMP_RAM_DATA' not described in enum 'ath10k_fw_crash_dump_type' drivers/net/wireless/ath/ath10k/coredump.h:27: warning: Enum value 'ATH10K_FW_CRASH_DUMP_MAX' not described in enum 'ath10k_fw_crash_dump_type' drivers/net/wireless/ath/ath10k/coredump.h:27: warning: Excess enum value 'ATH10K_FW_CRASH_DUMP_REGDUMP' description in 'ath10k_fw_crash_dump_type' Fix these issues with the enum ath10k_fw_crash_dump_type kernel-doc. No functional changes, compile tested only. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240118-ath10k-kerneldoc-v1-5-99c7e8d95aad@quicinc.com
2024-01-19wifi: ath10k: Fix htt_data_tx_completion kernel-doc warningJeff Johnson
Currently kernel-doc reports: drivers/net/wireless/ath/ath10k/htt.h:911: warning: Cannot understand * @brief target -> host TX completion indication message definition on line 911 - I thought it was a doc line This is because even though struct htt_data_tx_completion uses the kernel-doc marker "/**", it doesn't actual use kernel-doc syntax for the documentation. Rather than try to update this legacy driver documentation to use kernel-doc style, just replace the comment marker. No functional changes, compile tested only. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240118-ath10k-kerneldoc-v1-4-99c7e8d95aad@quicinc.com
2024-01-19wifi: ath10k: fix htt_q_state_conf & htt_q_state kernel-docJeff Johnson
Currently kernel-doc reports: drivers/net/wireless/ath/ath10k/htt.h:1488: warning: cannot understand function prototype: 'struct htt_q_state_conf ' drivers/net/wireless/ath/ath10k/htt.h:1542: warning: cannot understand function prototype: 'struct htt_q_state ' Update the kernel-doc for these two structs to resolve the warnings. No functional changes, compile tested only. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240118-ath10k-kerneldoc-v1-3-99c7e8d95aad@quicinc.com
2024-01-19wifi: ath10k: correctly document enum wmi_tlv_tx_pause_idJeff Johnson
Currently kernel-doc reports the issue: drivers/net/wireless/ath/ath10k/wmi-tlv.h:2363: warning: cannot understand function prototype: 'enum wmi_tlv_tx_pause_id ' Update the enum wmi_tlv_tx_pause_id documentation to fix this issue. No functional changes, compile tested only. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240118-ath10k-kerneldoc-v1-2-99c7e8d95aad@quicinc.com
2024-01-19wifi: ath10k: add missing wmi_10_4_feature_mask documentationJeff Johnson
Currently kernel-doc reports the following issues: drivers/net/wireless/ath/ath10k/wmi.h:3033: warning: Enum value 'WMI_10_4_EXT_PEER_TID_CONFIGS_SUPPORT' not described in enum 'wmi_10_4_feature_mask' drivers/net/wireless/ath/ath10k/wmi.h:3033: warning: Enum value 'WMI_10_4_REPORT_AIRTIME' not described in enum 'wmi_10_4_feature_mask' Update the kernel-doc for enum wmi_10_4_feature_mask to add the missing documentation. No functional changes, compile tested only. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240118-ath10k-kerneldoc-v1-1-99c7e8d95aad@quicinc.com
2024-01-18wifi: ath10k: replace ENOTSUPP with EOPNOTSUPPKarthikeyan Periyasamy
ENOTSUPP is not a standard error code, don't use it. Replace with EOPNOTSUPP instead. No functional changes, compile tested only. Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240117080431.2907471-4-quic_periyasa@quicinc.com
2023-12-21wifi: mac80211: rework RX timestamp flagsJohannes Berg
We only have a single flag free, and before using that for another mactime flag, instead refactor the mactime flags to use a 2-bit field. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Reviewed-by: Benjamin Berg <benjamin.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20231220133549.d0e664832d14.I20c8900106f9bf81316bed778b1e3ce145785274@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2023-12-18wifi: ath10k: remove duplicate memset() in 10.4 TDLS peer updateJeff Johnson
In [1] it was identified that in ath10k_wmi_10_4_gen_tdls_peer_update() the memset(skb->data, 0, sizeof(*cmd)) is unnecessary since function ath10k_wmi_alloc_skb() already zeroes skb->data, so remove it. No functional changes, compile tested only. [1] https://lore.kernel.org/linux-wireless/626ae2e7-66f8-423b-b17f-e75c1a6d29b3@embeddedor.com/ Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20231213-wmi_host_mem_chunks_flexarray-v1-6-92922d92fa2c@quicinc.com
2023-12-18wifi: ath10k: use flexible array in struct wmi_tdls_peer_capabilitiesJeff Johnson
Currently struct wmi_tdls_peer_capabilities defines: struct wmi_channel peer_chan_list[1]; Per the guidance in [1] this should be a flexible array, and at one point Gustavo was trying to fix this [2], but had questions about the correct behavior when the associated peer_chan_len is 0. I have been unable to determine if firmware requires that at least one record be present even if peer_chan_len is 0. But since that is the current behavior, follow the example from [3] and replace the one-element array with a union that contains both a flexible array and a single instance of the array element. This results in a struct that has the same footprint as the original, so no other driver changes are required. No functional changes, compile tested only. [1] https://docs.kernel.org/process/deprecated.html#zero-length-and-one-element-arrays [2] https://lore.kernel.org/linux-wireless/626ae2e7-66f8-423b-b17f-e75c1a6d29b3@embeddedor.com/ [3] https://lore.kernel.org/linux-wireless/202308301529.AC90A9EF98@keescook/ Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20231213-wmi_host_mem_chunks_flexarray-v1-5-92922d92fa2c@quicinc.com
2023-12-18wifi: ath10k: remove unused template structsJeff Johnson
Currently both the wmi_bcn_tmpl_cmd and wmi_prb_tmpl_cmd structs define: u8 data[1]; Per the guidance in [1] both instances of this should be flexible arrays. However during conversion it was discovered that neither of these structs are actually used, so just remove them. No functional changes, compile tested only. [1] https://docs.kernel.org/process/deprecated.html#zero-length-and-one-element-arrays Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20231213-wmi_host_mem_chunks_flexarray-v1-4-92922d92fa2c@quicinc.com
generated by cgit v1.2.3-70-g09d2 (git 2.48.1) at 2025-04-06 12:13:03 +0000