| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- replace power_supply_register_no_ws() with power_supply_register()
and a new "no_wakeup_source" field in struct power_supply_config
- constify battery info tables in the core and all drivers
- switch back to remove callback for all platform drivers
- allow power_supply_put() to be called from atomic context
- mark attribute arrays read-only after init
Power-supply drivers:
- new driver for TWL6030 and TWL6032
- rk817: improve battery capacity calibration
- misc small cleanups and fixes"
* tag 'for-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (42 commits)
power: reset: ep93xx: add AUXILIARY_BUS dependency
dt-bindings: power: reset: Convert mode-.* properties to array
power: supply: sc27xx: Fix battery detect GPIO probe
dt-bindings: power: supply: sc27xx-fg: document deprecated bat-detect-gpio
reset: keystone-reset: remove unused macros
power: supply: axp20x_battery: Use scaled iio_read_channel
power: supply: axp20x_usb_power: Use scaled iio_read_channel
power: supply: generic-adc-battery: change my gmail
power: supply: pmu_battery: Set power supply type to BATTERY
power: Switch back to struct platform_driver::remove()
power: supply: hwmon: move interface to private header
power: supply: rk817: Update battery capacity calibration
power: supply: rk817: stop updating info in suspend
power: supply: rt9471: Use IC status regfield to report real charger status
power: supply: rt9471: Fix wrong WDT function regfield declaration
dt-bindings: power/supply: qcom,pmi8998-charger: Drop incorrect "#interrupt-cells" from example
power: supply: core: mark attribute arrays as ro_after_init
power: supply: core: unexport power_supply_property_is_writeable()
power: supply: core: use device mutex wrappers
power: supply: bq27xxx: Fix registers of bq27426
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing updates from Bartosz Golaszewski:
- extend support for the wcn6855 model in the pwrseq-qcom-wcn driver
- make this driver depend on CONFIG_OF=y as it uses some very
OF-specific interfaces and depends on phandle parsing
* tag 'pwrseq-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
power: sequencing: qcom-wcn: improve support for wcn6855
power: sequencing: make the QCom PMU pwrseq driver depend on CONFIG_OF
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A rather large update for timekeeping and timers:
- The final step to get rid of auto-rearming posix-timers
posix-timers are currently auto-rearmed by the kernel when the
signal of the timer is ignored so that the timer signal can be
delivered once the corresponding signal is unignored.
This requires to throttle the timer to prevent a DoS by small
intervals and keeps the system pointlessly out of low power states
for no value. This is a long standing non-trivial problem due to
the lock order of posix-timer lock and the sighand lock along with
life time issues as the timer and the sigqueue have different life
time rules.
Cure this by:
- Embedding the sigqueue into the timer struct to have the same
life time rules. Aside of that this also avoids the lookup of
the timer in the signal delivery and rearm path as it's just a
always valid container_of() now.
- Queuing ignored timer signals onto a seperate ignored list.
- Moving queued timer signals onto the ignored list when the
signal is switched to SIG_IGN before it could be delivered.
- Walking the ignored list when SIG_IGN is lifted and requeue the
signals to the actual signal lists. This allows the signal
delivery code to rearm the timer.
This also required to consolidate the signal delivery rules so they
are consistent across all situations. With that all self test
scenarios finally succeed.
- Core infrastructure for VFS multigrain timestamping
This is required to allow the kernel to use coarse grained time
stamps by default and switch to fine grained time stamps when inode
attributes are actively observed via getattr().
These changes have been provided to the VFS tree as well, so that
the VFS specific infrastructure could be built on top.
- Cleanup and consolidation of the sleep() infrastructure
- Move all sleep and timeout functions into one file
- Rework udelay() and ndelay() into proper documented inline
functions and replace the hardcoded magic numbers by proper
defines.
- Rework the fsleep() implementation to take the reality of the
timer wheel granularity on different HZ values into account.
Right now the boundaries are hard coded time ranges which fail
to provide the requested accuracy on different HZ settings.
- Update documentation for all sleep/timeout related functions
and fix up stale documentation links all over the place
- Fixup a few usage sites
- Rework of timekeeping and adjtimex(2) to prepare for multiple PTP
clocks
A system can have multiple PTP clocks which are participating in
seperate and independent PTP clock domains. So far the kernel only
considers the PTP clock which is based on CLOCK TAI relevant as
that's the clock which drives the timekeeping adjustments via the
various user space daemons through adjtimex(2).
The non TAI based clock domains are accessible via the file
descriptor based posix clocks, but their usability is very limited.
They can't be accessed fast as they always go all the way out to
the hardware and they cannot be utilized in the kernel itself.
As Time Sensitive Networking (TSN) gains traction it is required to
provide fast user and kernel space access to these clocks.
The approach taken is to utilize the timekeeping and adjtimex(2)
infrastructure to provide this access in a similar way how the
kernel provides access to clock MONOTONIC, REALTIME etc.
Instead of creating a duplicated infrastructure this rework
converts timekeeping and adjtimex(2) into generic functionality
which operates on pointers to data structures instead of using
static variables.
This allows to provide time accessors and adjtimex(2) functionality
for the independent PTP clocks in a subsequent step.
- Consolidate hrtimer initialization
hrtimers are set up by initializing the data structure and then
seperately setting the callback function for historical reasons.
That's an extra unnecessary step and makes Rust support less
straight forward than it should be.
Provide a new set of hrtimer_setup*() functions and convert the
core code and a few usage sites of the less frequently used
interfaces over.
The bulk of the htimer_init() to hrtimer_setup() conversion is
already prepared and scheduled for the next merge window.
- Drivers:
- Ensure that the global timekeeping clocksource is utilizing the
cluster 0 timer on MIPS multi-cluster systems.
Otherwise CPUs on different clusters use their cluster specific
clocksource which is not guaranteed to be synchronized with
other clusters.
- Mostly boring cleanups, fixes, improvements and code movement"
* tag 'timers-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (140 commits)
posix-timers: Fix spurious warning on double enqueue versus do_exit()
clocksource/drivers/arm_arch_timer: Use of_property_present() for non-boolean properties
clocksource/drivers/gpx: Remove redundant casts
clocksource/drivers/timer-ti-dm: Fix child node refcount handling
dt-bindings: timer: actions,owl-timer: convert to YAML
clocksource/drivers/ralink: Add Ralink System Tick Counter driver
clocksource/drivers/mips-gic-timer: Always use cluster 0 counter as clocksource
clocksource/drivers/timer-ti-dm: Don't fail probe if int not found
clocksource/drivers:sp804: Make user selectable
clocksource/drivers/dw_apb: Remove unused dw_apb_clockevent functions
hrtimers: Delete hrtimer_init_on_stack()
alarmtimer: Switch to use hrtimer_setup() and hrtimer_setup_on_stack()
io_uring: Switch to use hrtimer_setup_on_stack()
sched/idle: Switch to use hrtimer_setup_on_stack()
hrtimers: Delete hrtimer_init_sleeper_on_stack()
wait: Switch to use hrtimer_setup_sleeper_on_stack()
timers: Switch to use hrtimer_setup_sleeper_on_stack()
net: pktgen: Switch to use hrtimer_setup_sleeper_on_stack()
futex: Switch to use hrtimer_setup_sleeper_on_stack()
fs/aio: Switch to use hrtimer_setup_sleeper_on_stack()
...
|
|
This fails to link when compile-testing and the auxiliary bus is not built-in:
x86_64-linux-ld: drivers/power/reset/ep93xx-restart.o: in function `ep93xx_reboot_driver_init':
ep93xx-restart.c:(.init.text+0x11): undefined reference to `__auxiliary_driver_register'
x86_64-linux-ld: drivers/power/reset/ep93xx-restart.o: in function `ep93xx_reboot_driver_exit':
ep93xx-restart.c:(.exit.text+0x8): undefined reference to `auxiliary_driver_unregister'
Add the appropriate dependency.
Fixes: 9fa7cdb4368f ("power: reset: Add a driver for the ep93xx reset")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241111104418.3891756-1-arnd@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The DT bindings specify the property as 'battery-detect-gpios', add
handling for it. Keep fallback to the deprecated 'bat-detect-gpio' property
to keep compatibility with older DTS.
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/ca28b2f2037929c0011fc5c779c332c1d1ad5308.1730720720.git.stano.jakubek@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
After reviewing the code, it was found that these macros are never
referenced in the code. Just remove them.
Signed-off-by: Ba Jing <bajing@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20241025090659.33458-1-bajing@cmss.chinamobile.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Change iio_read_channel_processed to iio_read_channel_processed_scale
where appropriate.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20241023184800.109376-3-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Change iio_read_channel_processed to iio_read_channel_processed_scale
where appropriate.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20241023184800.109376-2-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
change my contact in this driver.
Signed-off-by: anish kumar <yesanishhere@gmail.com>
Link: https://lore.kernel.org/r/20241023061126.7896-1-yesanishhere@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
If the power supply type is not set it defaults to "Unknown" and upower
does not recognise it. In turn battery monitor applications do not see a
battery. Setting to POWER_SUPPLY_TYPE_BATTERY fixes this.
Signed-off-by: Ed Robbins <edd.robbins@gmail.com>
Link: https://lore.kernel.org/r/IOFJLS.120OJ5KJG9R72@googlemail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Now that the SIG_IGN problem is solved in the core code, the alarmtimer
callbacks do not require a return value anymore.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/all/20241105064214.318837272@linutronix.de
|
|
WCN6855 (also known as QCA6490) is similar to the already supported
QCA6390 but takes in two more supplies so add a new vregs list for it.
On sm8450-hdk it also requires a short assert of the xo-clk pin so add
handling for it in a dedicated unit.
As we now have a separate set of targets for this variant, store the
pointer to the targets struct associated with a model in the device
match data.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241018-sc8280xp-pwrseq-v6-2-8da8310d9564@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
This driver uses various OF-specific functions and depends on phandle
parsing. There's no reason to make it available to non-OF systems so add
a relevant dependency switch to its Kconfig entry.
Fixes: 2f1630f437df ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets")
Link: https://lore.kernel.org/r/20241004130449.51725-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/power/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241010203622.839625-6-u.kleine-koenig@baylibre.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The interface of power_supply_hwmon.c is only meant to be used by the
psy core. Remove it from the public header file and use the private one
instead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241017-power-supply-cleanups-v2-1-cb0f5deab088@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The battery capacity calibration function continues to be a source of
bugs for end users, especially when coming out of suspend. This occurs
when the device has incorrect readings for voltage, and causes the
current code to set fully charged capacity incorrectly.
Add checks to ensure we don't attempt a capacity calibration when we
have invalid voltage values or no battery present, and remove the code
that attempts to automatically set the fully charged capacity in lieu of
making the value writeable. This way userspace is able to adjust the
fully charged capacity for a degraded battery.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240926144346.94630-3-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The driver has a thread that checks the battery every 8 seconds. Stop
this thread during device suspend as while the device is suspended not
all values seem to be read correctly (such as battery voltage). The
resume function triggers the thread to start again.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240926144346.94630-2-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use IC status regfield to rewrite the 'get_staus' function. The original
one cannot cover some special scenario like as charger OTG or JEITA case.
Fixes: 4a1a5f6781d8 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reported-by: Lucas Tsai <lucas_tsai@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/67ba92bb4a9c51d9cafadab30b788a3a2c3048e1.1727252762.git.cy_huang@richtek.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fix F_WDT and F_WDT_RST wrong regfield declaration.
Fixes: 4a1a5f6781d8 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reported-by: Lucas Tsai <lucas_tsai@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/f862e23f220612f01fabb6d8e76cfaf63756c22b.1727252762.git.cy_huang@richtek.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The attribute arrays are only modified during the __init phase.
To protect them against intentional or accidental modification,
mark them as __ro_after_init.
To make sure no modifications are introduced, also mark the return
values of the accessors as const.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241005-power-supply-cleanups-v1-3-45303b2d0a4d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Since commit ("power: supply: Drop use_cnt check from power_supply_property_is_writeable()"),
this function does not check use_cnt anymore, making it unsuitable for
general usage. As it is only used by the psy core anyways, remove it
from the public header and unexport it to avoid misusage.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241005-power-supply-cleanups-v1-2-45303b2d0a4d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The mutex is an implementation detail of struct device.
Use the dedicated wrappers to access the field.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241005-power-supply-cleanups-v1-1-45303b2d0a4d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Correct bq27426 registers, according to technical reference manual
it does not have Design Capacity register so it is not register
compatible with bq27421.
Fixes: 5ef6a16033b47 ("power: supply: bq27xxx: Add support for BQ27426")
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20241016-fix_bq27426-v2-1-aa6c0f51a9f6@mainlining.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
For historical reasons syscon-reboot has used an 'offset' property. As a
child on a MMIO bus having a 'reg' property is more appropriate. Accept
'reg' as an alternative to 'offset'.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241015225948.3971924-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add a driver for the charger in the TWL6030/32. For now it does not report
much in sysfs but parameters are set up for USB, charging is enabled with
the specified parameters. It stops charging when full and also restarts
charging.
This prevents ending up in a system setup where you run out of battery
although a charger is plugged in after precharge completed.
Battery voltage behavior was checked via the GPADC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20241016080314.222674-3-andreas@kemnade.info
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fix a typo in comments.
Reported-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Kreimer <algonell@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20240912125303.44118-1-algonell@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fixed some spelling errors, the details are as follows:
-in the code comments:
dettached->detached
meausered->measured
meausurement->measurement
sholuld->should
Tempreture->Temperature
measuremnts->measurements
detecing->detecting
persent->percent
Parallell->Parallel
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Link: https://lore.kernel.org/r/20240914085415.3886-1-shenlichuan@vivo.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The put_device() call in power_supply_put() may call
power_supply_dev_release(). The latter function does not sleep so
power_supply_put() doesn't sleep either. Hence, remove the might_sleep()
call from power_supply_put(). This patch suppresses false positive
complaints about calling a sleeping function from atomic context if
power_supply_put() is called from atomic context.
Cc: Kyle Tso <kyletso@google.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 1a352462b537 ("power_supply: Add power_supply_put for decrementing device reference counter")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240917193914.47566-1-bvanassche@acm.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The same functionality is available through
power_supply_config::no_wakeup_source, which is more idiomatic.
All users of the old API have been converted.
Also remove the argument "ws" from __power_supply_register(),
as it is now always "true".
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20241005-power-supply-no-wakeup-source-v1-8-1d62bf9bcb1d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
devm_power_supply_register()
devm_power_supply_register_no_ws() is going to be removed.
Switch to the general registration API.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20241005-power-supply-no-wakeup-source-v1-7-1d62bf9bcb1d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_register()
{,devm_}power_supply_register_no_ws() are going to be removed.
Switch to the general registration API.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20241005-power-supply-no-wakeup-source-v1-6-1d62bf9bcb1d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
devm_power_supply_register()
devm_power_supply_register_no_ws() is going to be removed.
Switch to the general registration API.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20241005-power-supply-no-wakeup-source-v1-5-1d62bf9bcb1d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_register()
devm_power_supply_register_no_ws() is going to be removed.
Switch to the general registration API.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20241005-power-supply-no-wakeup-source-v1-4-1d62bf9bcb1d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
devm_power_supply_register()
devm_power_supply_register_no_ws() is going to be removed.
Switch to the general registration API.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20241005-power-supply-no-wakeup-source-v1-3-1d62bf9bcb1d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
To inhibit wakeup users currently have to use dedicated functions to
register the power supply: {,devm_}power_supply_register_no_ws().
This is inconsistent to other runtime settings which can be configured
through struct power_supply_config.
It's also not obvious what _no_ws() is meant to mean.
Extend power_supply_config to also be able to inhibit the wakeup source.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20241005-power-supply-no-wakeup-source-v1-1-1d62bf9bcb1d@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The power supply core now allows this constification.
Prevent accidental or malicious modification of the data.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241005-power-supply-battery-const-v1-7-c1f721927048@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The power supply core now allows this constification.
Prevent accidental or malicious modification of the data.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241005-power-supply-battery-const-v1-6-c1f721927048@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The power supply core never modifies the ocv table.
Reflect this in the API, so drivers can mark their static tables as
const.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241005-power-supply-battery-const-v1-5-c1f721927048@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The table is not modified, so constify the reference.
This enables a constification in the power supply core.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241005-power-supply-battery-const-v1-4-c1f721927048@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The power supply core now allows this constification.
Prevent accidental or malicious modification of the data.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241005-power-supply-battery-const-v1-3-c1f721927048@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The power supply core now allows this constification.
Prevent accidental or malicious modification of the data.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241005-power-supply-battery-const-v1-2-c1f721927048@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The power supply core never modifies the resist table.
Reflect this in the API, so drivers can mark their static tables as
const.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241005-power-supply-battery-const-v1-1-c1f721927048@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing updates from Bartosz Golaszewski:
"There's one change adding support for a new PMU model and another
adding documentation for the subsystem which probably should have been
part of the initial commit but better late than never:
- add support for the new PMU variant inside the WCN6855 chipset
- add documentation for the subsystem"
* tag 'pwrseq-updates-for-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
Documentation: add a driver API doc for the power sequencing subsystem
power: sequencing: qcom-wcn: add support for the WCN6855 PMU
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon
devices
Drivers:
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
Documentation updates
Misc minor cleanups and fixes"
* tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: hwmon: Fix missing temp1_max_alarm attribute
power: supply: Drop use_cnt check from power_supply_property_is_writeable()
power: supply: ab8500: Constify struct kobj_type
power: supply: max1720x: fix a double free on error in probe()
power: supply: axp20x_battery: add support for AXP717
power: supply: axp20x_usb_power: Add support for AXP717
dt-bindings: power: supply: axp20x: Add AXP717 compatible
dt-bindings: power: supply: axp20x: Add AXP717 compatible
power: supply: axp20x_usb_power: Fix spelling mistake "reqested" -> "requested"
power: supply: Change usb_types from an array into a bitmask
power: supply: sysfs: Move power_supply_show_enum_with_available() up
power: supply: sysfs: Add power_supply_show_enum_with_available() helper
power: supply: rt9467-charger: Remove "usb_type" property write support
power: supply: ucs1002: Adjust ucs1002_set_usb_type() to accept string values
power: supply: "usb_type" property may be written to
power: supply: max1720x: add read support for nvmem
mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
power: supply: core: constify psy_tzd_ops
power: reset: brcmstb: Do not go into infinite loop if reset fails
power: reset: brcmstb: Use devm_register_sys_off_handler()
...
|
|
Temp channel 0 aka temp1 can have a temp1_max_alarm attribute for
power_supply devices which have a POWER_SUPPLY_PROP_TEMP_ALERT_MAX
property.
HWMON_T_MAX_ALARM was missing from power_supply_hwmon_info for
temp channel 0, causing the hwmon temp1_max_alarm attribute to be
missing from such power_supply devices.
Add this to power_supply_hwmon_info to fix this.
Fixes: f1d33ae806ec ("power: supply: remove duplicated argument in power_supply_hwmon_info")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240908185337.103696-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_property_is_writeable() gets called from the is_visible()
callback for the sysfs attributes of power_supply class devices and for
the sysfs attributes of power_supply core instantiated hwmon class devices.
These sysfs attributes get registered by the device_add() respectively
power_supply_add_hwmon_sysfs() calls in power_supply_register().
use_cnt gets initialized to 0 and is incremented only after these calls.
So when power_supply_property_is_writeable() gets called it always return
-ENODEV because of use_cnt == 0.
This causes all the attributes to have permissions of 444 even those which
should be writable. This used to be a problem only for hwmon sysfs
attributes but since commit be6299c6e55e ("power: supply: sysfs: use
power_supply_property_is_writeable()") this now also impacts power_supply
class sysfs attributes.
Fixes: be6299c6e55e ("power: supply: sysfs: use power_supply_property_is_writeable()")
Fixes: e67d4dfc9ff1 ("power: supply: Add HWMON compatibility layer")
Cc: stable@vger.kernel.org
Cc: Thomas Weißschuh <linux@weissschuh.net>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/stable/20240908185337.103696-1-hdegoede%40redhat.com
Link: https://lore.kernel.org/r/20240908185337.103696-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Implement the reset behaviour of the various EP93xx SoCS
in drivers/power/reset.
It used to be located in arch/arm/mach-ep93xx.
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This 'struct kobj_type' is not modified. It is only used in
kobject_init_and_add() which takes a 'const struct kobj_type *ktype'
parameter.
Constifying this structure and moving it to a read-only section,
and can increase over all security.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://lore.kernel.org/r/20240904011434.2010118-1-lihongbo22@huawei.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
