| Age | Commit message (Collapse) | Author |
|---|
|
Modify the thermal core to use three lists of trip points:
trips_high, containing trips with thresholds strictly above the current
thermal zone temperature,
trips_reached, containing trips with thresholds at or below the current
zone temperature,
trips_invalid, containing trips with temperature equal to
THERMAL_ZONE_INVALID,
where the first two lists are always sorted by the current trip
threshold.
For each trip in trips_high, there is no mitigation under way and
the trip threshold is equal to its temperature. In turn, for each
trip in trips_reached, there is mitigation under way and the trip
threshold is equal to its low temperature. The trips in trips_invalid,
of course, need not be taken into consideration.
The idea is to make __thermal_zone_device_update() walk trips_high and
trips_reached instead of walking the entire table of trip points in a
thermal zone. Usually, it will only need to walk a few entries in one
of the lists and check one entry in the other list, depending on the
direction of the zone temperature changes, because crossing many trips
by the zone temperature in one go between two consecutive temperature
checks should be unlikely (if it occurs often, the thermal zone
temperature should probably be checked more often either or there
are too many trips).
This also helps to eliminate one temporary trip list used for trip
crossing notification (only one temporary list is needed for this
purpose instead of two) and the remaining temporary list may be sorted
by the current trip threshold value, like the trips_reached list, so
the additional notify_temp field in struct thermal_trip_desc is not
necessary any more.
Moreover, since the trips_reached and trips_high lists are sorted,
the "low" and "high" values needed by thermal_zone_set_trips() can be
determined in a straightforward way by looking at one end of each list.
Of course, additional work is needed in some places in order to
maintain the ordering of the lists, but it is limited to situations
that should be rare, like updating a trip point temperature or
hysteresis, thermal zone initialization, or system resume.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/2003443.usQuhbGJ8B@rjwysocki.net
[ rjw: Added a comment to thermal_zone_handle_trips() ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since thermal_zone_set_trip_temp() is now located in the same file
as thermal_trip_crossed(), it can invoke the latter directly without
using the thermal_zone_trip_down() wrapper that has no other users.
Update thermal_zone_set_trip_temp() accordingly and drop
thermal_zone_trip_down().
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/1807510.VLH7GnMWUR@rjwysocki.net
|
|
In preparation for subsequent changes, modify thermal_trip_crossed()
to take a trip descriptor pointer instead of a pointer to struct
thermal_trip and propagate this change to thermal_zone_trip_down().
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/10547668.nUPlyArG6x@rjwysocki.net
|
|
Since the list node field in struct thermal_trip_desc is going to be
used for purposes other than trip crossing notification, rename it
to list_node.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/2201558.irdbgypaU6@rjwysocki.net
|
|
Three thermal governors call __thermal_cdev_update() under the
cdev lock without doing any checks, so in order to reduce the
related code duplication, introduce a new helper function called
thermal_cdev_update_nocheck() for them and make them use it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/1835097.VLH7GnMWUR@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
Add a guard for unlocking a locked thermal zone temporarily and use it
in thermal_zone_pm_prepare().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/3344086.aeNJFYEL58@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
Add and use a guard for thermal zone locking.
This allows quite a few error code paths to be simplified among
other things and brings in a noticeable code size reduction for
a good measure.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/1930069.tdWV9SEqCh@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
In almost all places where a thermal zone's list of thermal instances
is walked, there is a check to match a specific trip point and it is
walked in vain whenever there are no cooling devices associated with
the given trip.
To address this, store the lists of thermal instances in trip point
descriptors instead of storing them in thermal zones and adjust all
code using those lists accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/5522726.Sb9uPGUboI@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
After previous changes, the need_update field in struct thermal_zone_device
is only set and never read, so drop it.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2495061.jE0xQCEvom@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
In analogy with a previous change in the thermal zone registration code
path, to ensure that __thermal_zone_device_update() will return early
for thermal zones that are going away, introduce a thermal zone state
flag representing the "exit" state and set it while deleting the thermal
zone from thermal_tz_list.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/4394176.ejJDZkT8p0@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
After thermal_zone_device_register_with_trips() has called
device_register() and it has registered the new thermal zone device
with the driver core, user space may access its sysfs attributes and,
among other things, it may enable the thermal zone before it is ready.
To address this, introduce a new thermal zone state flag for
initialization and set it before calling device_register() in
thermal_zone_device_register_with_trips(). This causes
__thermal_zone_device_update() to return early until the new flag
is cleared.
To clear it when the thermal zone is ready, introduce a new
function called thermal_zone_init_complete() that will also invoke
__thermal_zone_device_update() after clearing that flag (both under the
thernal zone lock) and make thermal_zone_device_register_with_trips()
call the new function instead of checking need_update and calling
thermal_zone_device_update() when it is set.
After this change, if user space enables the thermal zone prematurely,
__thermal_zone_device_update() will return early for it until
thermal_zone_init_complete() is called. In turn, if the thermal zone
is not enabled by user space before thermal_zone_init_complete() is
called, the __thermal_zone_device_update() call in it will return early
because the thermal zone has not been enabled yet, but that function
will be invoked again by thermal_zone_device_set_mode() when the thermal
zone is enabled and it will not return early this time.
The checking of need_update is not necessary any more because the
__thermal_zone_device_update() calls potentially triggered by cooling
device binding take place before calling thermal_zone_init_complete(),
so they all will return early, which means that
thermal_zone_init_complete() must call __thermal_zone_device_update()
in case the thermal zone is enabled prematurely by user space.
Fixes: 203d3d4aa482 ("the generic thermal sysfs driver")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/9360231.CDJkKcVGEf@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
Instead of using two separate fields in struct thermal_zone_device for
representing flags related to thermal zone suspend, represent them
explicitly as bits in one u8 "state" field.
Subsequently, that field will be used for addressing race conditions
related to thermal zone initialization and exit.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/7733910.EvYhyI6sBW@rjwysocki.net
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
The user thresholds mechanism is a way to have the userspace to tell
the thermal framework to send a notification when a temperature limit
is crossed. There is no id, no hysteresis, just the temperature and
the direction of the limit crossing. That means we can be notified
when a threshold is crossed the way up only, or the way down only or
both ways. That allows to create hysteresis values if it is needed.
A threshold can be added, deleted or flushed. The latter means all
thresholds belonging to a thermal zone will be deleted.
When a threshold is added:
- if the same threshold (temperature and direction) exists, an error
is returned
- if a threshold is specified with the same temperature but a
different direction, the specified direction is added
- if there is no threshold with the same temperature then it is
created
When a threshold is deleted:
- if the same threshold (temperature and direction) exists, it is
deleted
- if a threshold is specified with the same temperature but a
different direction, the specified direction is removed
- if there is no threshold with the same temperature, then an error
is returned
When the threshold are flushed:
- All thresholds related to a thermal zone are deleted
When a threshold is crossed:
- the userspace does not need to know which threshold(s) have been
crossed, it will be notified with the current temperature and the
previous temperature
- if multiple thresholds have been crossed between two updates only
one notification will be send to the userspace, it is pointless to
send a notification per thresholds crossed as the userspace can
handle that easily when it has the temperature delta information
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://patch.msgid.link/20240923100005.2532430-2-daniel.lezcano@linaro.org
[ rjw: Subject edit, use BIT(0) and BIT(1) in symbol definitions ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are places in the thermal netlink code where nothing prevents
the thermal zone object from going away while being accessed after it
has been returned by thermal_zone_get_by_id().
To address this, make thermal_zone_get_by_id() get a reference on the
thermal zone device object to be returned with the help of get_device(),
under thermal_list_lock, and adjust all of its callers to this change
with the help of the cleanup.h infrastructure.
Fixes: 1ce50e7d408e ("thermal: core: genetlink support for events/cmd/sampling")
Cc: 6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/6112242.lOV4Wx5bFT@rjwysocki.net
|
|
There are only two callers of thermal_zone_device_is_enabled()
and one of them call is under the zone lock and the other one uses
lockdep_assert_held() on that lock. Thus the lockdep_assert_held()
in thermal_zone_device_is_enabled() is redundant and it could be
dropped, but then the function would merely become a wrapper around
a simple tz->mode check that is more convenient to do directly.
Accordingly, drop thermal_zone_device_is_enabled() altogether and update
its callers to check tz->mode directly as appropriate.
While at it, combine the tz->mode and tz->suspended checks in
__thermal_zone_device_update() because they are of a similar category
and if any of them evaluates to "true", the outcome is the same.
No intentinal functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/9353673.CDJkKcVGEf@rjwysocki.net
|
|
After recent changes, it is only used for printing a debug message
in __thermal_cdev_update() which arguably is not worth preserving.
Drop it along with the dev_dbg() statement using it.
Link: https://lore.kernel.org/linux-pm/4a8d8f5a-122d-4c26-b8d6-76a65e42216b@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://patch.msgid.link/4934182.GXAFRqVoOG@rjwysocki.net
|
|
In order to set the scene for the thresholds support which have to
manipulate the low and high temperature boundaries for the interrupt
support, we must pass the low and high values to the incoming
thresholds routine.
The variables are set from the thermal_zone_set_trips() where the
function loops the thermal trips to figure out the next and the
previous temperatures to set the interrupt to be triggered when they
are crossed.
These variables will be needed by the function in charge of handling
the thresholds in the incoming changes but they are local to the
aforementioned function thermal_zone_set_trips().
Move the low and high boundaries computation out of the function in
thermal_zone_device_update() so they are accessible from there.
The positive side effect is they are computed in the same loop as
handle_thermal_trip(), so we remove one loop.
Co-developed-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://patch.msgid.link/20240816081241.1925221-2-daniel.lezcano@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Change trip_point_hyst_store() and replace thermal_zone_trip_updated()
with thermal_zone_set_trip_hyst() to follow the trip_point_temp_store()
code pattern for more consistency.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/5508466.Sb9uPGUboI@rjwysocki.net
|
|
Instead of allocating memory for trip point sysfs attributes separately,
store them in struct thermal_trip_desc for each trip individually which
allows a few extra memory allocations to be avoided.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/46571375.fMDQidcC6G@rjwysocki.net
|
|
There are no more users of get_thermal_instance(), so drop it.
While at it, replace get_instance() returning a pointer to struct
thermal_instance with thermal_instance_present() returning a bool
which is more straightforward.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/2014591.usQuhbGJ8B@rjwysocki.net
[ rjw: Dropped get_thermal_instance() documentation ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone
temperature is invalid") introduced a polling mechanism by which the
thermal core attampts to get a valid temperature value for thermal zones
where the .get_temp() callback returns errors to start with (for
example, due to initialization ordering woes). However, this polling is
carried out periodically ad infinitum and every iteration of it causes
a message to be printed to the kernel log which means a lot of log noise
on systems where there are thermal zones that never get ready for some
reason. It is also not really useful to continuously poll thermal zones
that never respond.
To address this, modify the thermal core to increase the delay between
consecutive thermal zone temperature checks after every check that fails
until it reaches a certain maximum value. At that point, the thermal
zone in question will be disabled, but user space will be able to
reenable it if it believes that the failure is transient.
Also change the code to print messages regarding failed temperature
checks to the kernel log only twice, once when the thermal zone's
.get_temp() callback returns an error for the first time and once when
disabling the given thermal zone. In addition, a dev_crit() message
will be printed at that point if the given thermal zone contains a
critical trip point to notify the system operator about the situation.
Fixes: a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid")
Link: https://lore.kernel.org/linux-acpi/CAGnHSE=RyPK++UG0-wAtVKgeJxe0uzFYgLxm+RUOKKoQquW=Ow@mail.gmail.com/
Reported-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2962033.e9J7NaK4W3@rjwysocki.net
|
|
The iwlwifi wireless driver registers a thermal zone that is only needed
when the network interface handled by it is up and it wants that thermal
zone to be effectively ignored by the core otherwise.
Before commit a8a261774466 ("thermal: core: Call monitor_thermal_zone()
if zone temperature is invalid") that could be achieved by returning
an error code from the thermal zone's .get_temp() callback because the
core did not really handle errors returned by it almost at all.
However, commit a8a261774466 made the core attempt to recover from the
situation in which the temperature of a thermal zone cannot be
determined due to errors returned by its .get_temp() and is always
invalid from the core's perspective.
That was done because there are thermal zones in which .get_temp()
returns errors to start with due to some difficulties related to the
initialization ordering, but then it will start to produce valid
temperature values at one point.
Unfortunately, the simple approach taken by commit a8a261774466,
which is to poll the thermal zone periodically until its .get_temp()
callback starts to return valid temperature values, is at odds with
the special thermal zone in iwlwifi in which .get_temp() may always
return an error because its network interface may always be down. If
that happens, every attempt to invoke the thermal zone's .get_temp()
callback resulting in an error causes the thermal core to print a
dev_warn() message to the kernel log which is super-noisy.
To address this problem, make the core handle the case in which
.get_temp() returns 0, but the temperature value returned by it
is not actually valid, in a special way. Namely, make the core
completely ignore the invalid temperature value coming from
.get_temp() in that case, which requires folding in
update_temperature() into its caller and a few related changes.
On the iwlwifi side, modify iwl_mvm_tzone_get_temp() to return 0
and put THERMAL_TEMP_INVALID into the temperature return memory
location instead of returning an error when the firmware is not
running or it is not of the right type.
Also, to clearly separate the handling of invalid temperature
values from the thermal zone initialization, introduce a special
THERMAL_TEMP_INIT value specifically for the latter purpose.
Fixes: a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid")
Closes: https://lore.kernel.org/linux-pm/20240715044527.GA1544@sol.localdomain/
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201761
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: 6.10+ <stable@vger.kernel.org> # 6.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/4950004.31r3eYUQgx@rjwysocki.net
[ rjw: Rebased on top of the current mainline ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Commit 202aa0d4bb53 ("thermal: core: Do not call handle_thermal_trip()
if zone temperature is invalid") caused __thermal_zone_device_update()
to return early if the current thermal zone temperature was invalid.
This was done to avoid running handle_thermal_trip() and governor
callbacks in that case which led to confusion. However, it went too
far because monitor_thermal_zone() still needs to be called even when
the zone temperature is invalid to ensure that it will be updated
eventually in case thermal polling is enabled and the driver has no
other means to notify the core of zone temperature changes (for example,
it does not register an interrupt handler or ACPI notifier).
Also if the .set_trips() zone callback is expected to set up monitoring
interrupts for a thermal zone, it has to be provided with valid
boundaries and that can only happen if the zone temperature is known.
Accordingly, to ensure that __thermal_zone_device_update() will
run again after a failing zone temperature check, make it call
monitor_thermal_zone() regardless of whether or not the zone
temperature is valid and make the latter schedule a thermal zone
temperature update if the zone temperature is invalid even if
polling is not enabled for the thermal zone.
Fixes: 202aa0d4bb53 ("thermal: core: Do not call handle_thermal_trip() if zone temperature is invalid")
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2764814.mvXUDI8C0e@rjwysocki.net
[ rjw: Changed THERMAL_RECHECK_DELAY_MS to 250 ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Merge thermal core changes for v6.11:
- Fix and clean up several minor shortcomings in thermal debug (Rafael
Wysocki).
- Rename __thermal_zone_set_trips() to thermal_zone_set_trips() and
make it use trip thresholds (Rafael Wysocki).
- Use READ_ONCE() for lockless access to trip temperature and
hysteresis (Rafael Wysocki).
- Drop unnecessary cooling device target state checks from the
Bang-Bang thermal governor (Rafael Wysocki).
- Avoid invoking thermal governor .trip_crossed() callback for critical
and hot trip points (Rafael Wysocki).
* thermal-core:
thermal: core: Avoid calling .trip_crossed() for critical and hot trips
thermal: gov_bang_bang: Drop unnecessary cooling device target state checks
thermal: trip: Use READ_ONCE() for lockless access to trip properties
thermal: trip: Make thermal_zone_set_trips() use trip thresholds
thermal: trip: Rename __thermal_zone_set_trips() to thermal_zone_set_trips()
thermal: trip: Use common set of trip type names
thermal/debugfs: Move some statements from under thermal_dbg->lock
thermal/debugfs: Compute maximum temperature for mitigation episode as a whole
thermal/debugfs: Adjust check for trips without statistics in tze_seq_show()
thermal/debugfs: Fix up units in "mitigations" files
thermal/debugfs: Print mitigation timestamp value in milliseconds
thermal/debugfs: Do not extend mitigation episodes beyond system resume
thermal/debugfs: Use helper to update trip point overstepping duration
|
|
After commit 5a5efdaffda5 ("thermal: core: Resume thermal zones
asynchronously") it is theoretically possible that, if a system suspend
starts immediately after a system resume, thermal_zone_device_resume()
spawned by the thermal PM notifier for one of the thermal zones at the
end of the system resume will run after the PM thermal notifier for the
suspend-prepare action. If that happens, tz->suspended set by the latter
will be reset by the former which may lead to unexpected consequences.
To avoid that race, synchronize thermal_zone_device_resume() with the
suspend-prepare thermal PM notifier with the help of additional bool
field and completion in struct thermal_zone_device.
Note that this also ensures running __thermal_zone_device_update() at
least once for each thermal zone between system resume and the following
system suspend in case it is needed to start thermal mitigation.
Fixes: 5a5efdaffda5 ("thermal: core: Resume thermal zones asynchronously")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Drop the pointless double underline prefix from the function name as per
the subject.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use the same set of trip type names in sysfs and in the thermal debug
code output.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
mitigation become invalid
When a trip point becomes invalid after being crossed on the way up,
it is involved in a mitigation episode that needs to be adjusted to
compensate for the trip going away.
For this reason, introduce thermal_zone_trip_down() as a wrapper
around thermal_trip_crossed() and make thermal_zone_set_trip_temp()
call it if the new temperature of the trip at hand is equal to
THERMAL_TEMP_INVALID and it has been crossed on the way up to trigger
all of the necessary adjustments in user space, the thermal debug
code and the zone governor.
Fixes: 8c69a777e480 ("thermal: core: Fix the handling of invalid trip points")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since all of the governors in the tree have been switched over to using
the new callbacks, either .trip_crossed() or .manage(), the .throttle()
governor callback is not used any more, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Introduce a new thermal governor callback called .manage() that will be
invoked once per thermal zone update after processing all of the trip
points in the core.
This will allow governors that look at multiple trip points together
to check all of them in a consistent configuration, so they don't need
to play tricks with skipping .throttle() invocations that they are not
interested in and they can avoid carrying out the same computations for
multiple times in one cycle.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Introduce a new thermal governor callback called .trip_crossed()
that will be invoked whenever a trip point is crossed by the zone
temperature, either on the way up or on the way down.
The trip crossing direction information will be passed to it and if
multiple trips are crossed in the same direction during one thermal zone
update, the new callback will be invoked for them in temperature order,
either ascending or descending, depending on the trip crossing
direction.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
Notice that struct thermal_governor is only used by the thermal core
and so move its definition to thermal_core.h.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
If multiple trip points are crossed in one go and the trips table in
the thermal zone device object is not sorted, the corresponding trip
point crossing notifications sent to user space will not be ordered
either.
Moreover, if the trips table is sorted by trip temperature in ascending
order, the trip crossing notifications on the way up will be sent in that
order too, but the trip crossing notifications on the way down will be
sent in the reverse order.
This is generally confusing and it is better to make the kernel send the
notifications in the order of growing (on the way up) or falling (on the
way down) trip temperature.
To achieve that, instead of sending a trip crossing notification and
recording a trip crossing event in the statistics right away from
handle_thermal_trip(), put the trip in question on a list that will be
sorted by __thermal_zone_device_update() after processing all of the trips
and before sending the notifications and recording trip crossing events.
Link: https://lore.kernel.org/linux-pm/20240306085428.88011-1-daniel.lezcano@linaro.org/
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
Move the definitions of struct thermal_trip_desc and struct
thermal_zone_device to an internal header file in the thermal core,
as they don't need to be accessible to any code other than the thermal
core and so they don't need to be present in a global header.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The threshold field in struct thermal_trip is only used internally by
the thermal core and it is better to prevent drivers from misusing it.
It also takes some space unnecessarily in the trip tables passed by
drivers to the core during thermal zone registration.
For this reason, introduce struct thermal_trip_desc as a wrapper around
struct thermal_trip, move the threshold field directly into it and make
the thermal core store struct thermal_trip_desc objects in the internal
thermal zone trip tables. Adjust all of the code using trip tables in
the thermal core accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
In order to allow thermal zone creators to specify the writability of
trip point temperature and hysteresis on a per-trip basis, add a flags
field to struct thermal_trip and define flags to represent the desired
trip properties.
Also make thermal_zone_device_register_with_trips() set the
THERMAL_TRIP_FLAG_RW_TEMP flag for all trips covered by the writable
trips mask passed to it and modify the thermal sysfs code to look at
the trip flags instead of using the writable trips mask directly or
checking the presence of the .set_trip_hyst() zone callback.
Additionally, make trip_point_temp_store() and trip_point_hyst_store()
fail with an error code if the trip passed to one of them has
THERMAL_TRIP_FLAG_RW_TEMP or THERMAL_TRIP_FLAG_RW_HYST,
respectively, clear in its flags.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The thermal framework does not have any debug information except a
sysfs stat which is a bit controversial. This one allocates big chunks
of memory for every cooling devices with a high number of states and
could represent on some systems in production several megabytes of
memory for just a portion of it. As the sysfs is limited to a page
size, the output is not exploitable with large data array and gets
truncated.
The patch provides the same information than sysfs except the
transitions are dynamically allocated, thus they won't show more
events than the ones which actually occurred. There is no longer a
size limitation and it opens the field for more debugging information
where the debugfs is designed for, not sysfs.
The thermal debugfs directory structure tries to stay consistent with
the sysfs one but in a very simplified way:
thermal/
-- cooling_devices
|-- 0
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
|-- 1
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
|-- 2
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
|-- 3
| |-- clear
| |-- time_in_state_ms
| |-- total_trans
| `-- trans_table
`-- 4
|-- clear
|-- time_in_state_ms
|-- total_trans
`-- trans_table
The content of the files in the cooling devices directory is the same
as the sysfs one except for the trans_table which has the following
format:
Transition Hits
1->0 246
0->1 246
2->1 632
1->2 632
3->2 98
2->3 98
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: White space fixups, rebase ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Because thermal_zone_trip_id() does not update the thermal zone object
passed to it, its pointer argument representing the thermal zone can be
const, so adjust its definition accordingly.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux into thermal
Merge thermal control material for 6.8-rc1 from Daniel Lezcano:
"- Converted Mediatek Thermal to the json-schema (Rafał Miłecki)
- Fixed DT bindings issue on Loongson (Binbin Zhou)
- Fixed returning NULL instead of -ENODEV on Loogsoo (Binbin Zhou)
- Added the DT binding for the tsens on SM8650 platform (Neil Armstrong)
- Added a reboot on critical option feature (Fabio Estevam)
- Made usage of DEFINE_SIMPLE_DEV_PM_OPS on AmLogic (Uwe Kleine-König)
- Added the D1/T113s THS controller support on Sun8i (Maxim Kiselev)
- Fixed example in the DT binding for QCom SPMI (Johan Hovold)
- Fixed compilation warning for the tmon utility (Florian Eckert)
- Added interrupt based configuration on Exynos along with a set of
related cleanups (Mateusz Majewski)"
* tag 'thermal-v6.8-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (24 commits)
thermal/drivers/exynos: Use set_trips ops
thermal/drivers/exynos: Use BIT wherever possible
thermal/drivers/exynos: Split initialization of TMU and the thermal zone
thermal/drivers/exynos: Stop using the threshold mechanism on Exynos 4210
thermal/drivers/exynos: Simplify regulator (de)initialization
thermal/drivers/exynos: Handle devm_regulator_get_optional return value correctly
thermal/drivers/exynos: Wwitch from workqueue-driven interrupt handling to threaded interrupts
thermal/drivers/exynos: Drop id field
thermal/drivers/exynos: Remove an unnecessary field description
tools/thermal/tmon: Fix compilation warning for wrong format
dt-bindings: thermal: qcom-spmi-adc-tm5/hc: Clean up examples
dt-bindings: thermal: qcom-spmi-adc-tm5/hc: Fix example node names
thermal/drivers/sun8i: Add D1/T113s THS controller support
dt-bindings: thermal: sun8i: Add binding for D1/T113s THS controller
thermal: amlogic: Use DEFINE_SIMPLE_DEV_PM_OPS for PM functions
thermal: amlogic: Make amlogic_thermal_disable() return void
thermal/thermal_of: Allow rebooting after critical temp
reboot: Introduce thermal_zone_device_critical_reboot()
thermal/core: Prepare for introduction of thermal reboot
dt-bindings: thermal-zones: Document critical-action
...
|
|
Introduce thermal_zone_device_critical_reboot() to trigger an
emergency reboot.
It is a counterpart of thermal_zone_device_critical() with the
difference that it will force a reboot instead of shutdown.
The motivation for doing this is to allow the thermal subystem
to trigger a reboot when the temperature reaches the critical
temperature.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231129124330.519423-3-festevam@gmail.com
|
|
Add a new callback to the struct thermal_governor. It can be used for
updating governors when there is a change in the thermal zone internals,
e.g. thermal cooling device is bind to the thermal zone.
That makes possible to move some heavy operations like memory allocations
related to the number of cooling instances out of the throttle() callback.
Both callback code paths (throttle() and update_tz()) are protected with
the same thermal zone lock, which guaranties the consistency.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The __thermal_zone_get_trip() header in drivers/thermal/thermal_core.h
is redundant, because there is one already in thermal.h, so drop it.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Both trip_point_temp_store() and trip_point_hyst_store() use
thermal_zone_set_trip() to update a given trip point, but none of them
actually needs to change more than one field in struct thermal_trip
representing it. However, each of them effectively calls
__thermal_zone_get_trip() twice in a row for the same trip index value,
once directly and once via thermal_zone_set_trip(), which is not
particularly efficient, and the way in which thermal_zone_set_trip()
carries out the update is not particularly straightforward.
Moreover, input processing need not be done under the thermal zone lock
in any of these functions.
Rework trip_point_temp_store() and trip_point_hyst_store() to address
the above, move the part of thermal_zone_set_trip() that is still
useful to a new function called thermal_zone_trip_updated() and drop
the rest of it.
While at it, make trip_point_hyst_store() reject negative hysteresis
values.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Modify the governor .throttle() callback definition so that it takes a
trip pointer instead of a trip index as its second argument, adjust the
governors accordingly and update the core code invoking .throttle().
This causes the governors to become independent of the representation
of the list of trips in the thermal zone structure.
This change is not expected to alter the general functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Define a new macro for_each_trip() to be used by the thermal core code
and thermal governors for walking trips in a given thermal zone.
Modify for_each_thermal_trip() to use this macro instead of an open-
coded loop over trips.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
|
|
Replace the integer trip number stored in struct thermal_instance with
a pointer to the relevant trip and adjust the code using the structure
in question accordingly.
The main reason for making this change is to allow the trip point to
cooling device binding code more straightforward, as illustrated by
subsequent modifications of the ACPI thermal driver, but it also helps
to clarify the overall design and allows the governor code overhead to
be reduced (through subsequent modifications).
The only case in which it adds complexity is trip_point_show() that
needs to walk the trips[] table to find the index of the given trip
point, but this is not a critical path and the interface that
trip_point_show() belongs to is problematic anyway (for instance, it
doesn't cover the case when the same cooling devices is associated
with multiple trip points).
This is a preliminary change and the affected code will be refined by
a series of subsequent modifications of thermal governors, the core and
the ACPI thermal driver.
The general functionality is not expected to be affected by this change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Passing a struct thermal_trip pointer instead of a trip index to the
.get_trend() thermal zone callback allows one of its 2 implementations,
the thermal_get_trend() function in the ACPI thermal driver, to be
simplified quite a bit, and the other implementation of it in the
ti-soc-thermal driver does not even use the relevant callback argument.
For this reason, change the .get_trend() thermal zone callback
definition and adjust the related code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rework the currently unused __for_each_thermal_trip() to pass original
pointers to struct thermal_trip objects to the callback, so it can be
used for updating trip data (e.g. temperatures), rename it to
for_each_thermal_trip() and make it available to modular drivers.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For many setups the bang-bang governor is exactly what we want. Many
ARM SoC-based devices use fans to cool down the entire SoC and that
works well only with the bang-bang governor because it uses the
hysteresis in order to let the fan run for a while to cool the SoC
down below the trip point before switching it off again.
The step-wise governor will behave strangely in these situations. It
doesn't use the hysteresis, so it can lead to situations where the fan
is turned on for only a very brief period and then is switched back off,
only to get switched back on again very quickly because the SoC hasn't
cooled down very much.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230609124408.3788680-1-thierry.reding@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
