| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work
going into the debugfs interface for the thunderbolt (i.e. USB4) code,
to help with debugging the myrad ways that hardware vendors get their
interfaces messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: typec: tcpm: Add support for sink-bc12-completion-time-ms DT property
dt-bindings: usb: maxim,max33359: add usage of sink bc12 time property
dt-bindings: connector: Add time property for Sink BC12 detection completion
usb: dwc3: gadget: Remove dwc3_request->needs_extra_trb
usb: dwc3: gadget: Cleanup SG handling
usb: dwc3: gadget: Fix looping of queued SG entries
usb: dwc3: gadget: Fix checking for number of TRBs left
usb: dwc3: ep0: Don't clear ep0 DWC3_EP_TRANSFER_STARTED
Revert "usb: gadget: composite: fix OS descriptors w_value logic"
usb: ehci-spear: fix call balance of sehci clk handling routines
USB: make to_usb_device_driver() use container_of_const()
USB: make to_usb_driver() use container_of_const()
USB: properly lock dynamic id list when showing an id
USB: make single lock for all usb dynamic id lists
drivers/usb/storage: refactor min with min_t
drivers/usb/serial: refactor min with min_t
drivers/usb/musb: refactor min/max with min_t/max_t
drivers/usb/mon: refactor min with min_t
drivers/usb/misc: refactor min with min_t
drivers/usb/host: refactor min/max with min_t/max_t
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
- Several drivers, including atmel-flexcom/rk8xx-core, palmas, and
tps65010, have undergone minor code improvements to enhance
consistency and fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0
capability for consistent register map configuration across syscons
of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device
compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced
regulator put and ensure proper synchronization during driver
removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant
improvements, including the use of IRQ domains for various devices,
fixing IRQ domain names duplication, and code refactoring for better
consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break
statement in the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver,
along with ensuring a clear relationship between IDs and model names,
and allowing multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved
power management.
- The adp5585 driver has reduced its dependencies by dropping the
obsolete dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397
driver, expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name
from IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing
regmap_del_irq_chip() in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated
i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML
format for better readability and maintainability.
* tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (62 commits)
dt-bindings: mfd: bd71828: Use charger resistor in mOhm instead of MOhm
dt-bindings: mfd: sprd,sc2731: Convert to YAML
mfd: tqmx86: Add I2C IRQ support
mfd: tqmx86: Make IRQ setup errors non-fatal
mfd: tqmx86: Refactor GPIO IRQ setup
mfd: tqmx86: Improve gpio_irq module parameter description
mfd: tqmx86: Add board definitions for TQMx120UC, TQMx130UC and TQMxE41S
mfd: 88pm886: Add the RTC cell
dt-bindings: mfd: Add Realtek RTL9300 switch peripherals
mfd: intel_soc_pmic_crc: Add support for non ACPI instantiated i2c_client
mfd: intel_soc_pmic_*: Consistently use filename as driver name
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917
mfd: rt5033: Fix missing regmap_del_irq_chip()
mfd: cgbc-core: Fix error handling paths in cgbc_init_device()
dt-bindings: mfd: aspeed: Support for AST2700
mfd: Switch back to struct platform_driver::remove()
dt-bindings: mfd: qcom,spmi-pmic: Document PMICs added in SM8750
mfd: rtc: bd7xxxx Drop IC name from IRQ
mfd: mt6397: Add initial support for MT6328
mfd: adp5585: Drop obsolete dependency on COMPILE_TEST
...
|
|
Add support for parsing DT time property "sink-bc12-completion-time-ms".
This timer is used to relax the PD state machine during Sink attach to
allow completion of Battery Charging (BC1.2) charger type detection in
TCPC before PD negotiations. BC1.2 detection is a hardware mechanism to
detect charger port type that is run by some controllers (such as
"maxim,max33359") in parallel to Type-C connection state machines.
This is to ensure that BC1.2 completes before PD is enabled as running
BC1.2 in parallel with PD negotiation results in delays violating timer
constraints in PD spec.
This is an optional timer and will not add any delay unless explicitly
set.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241103034402.2460252-4-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the read of USB_PDPHY_RX_ACKNOWLEDGE_REG failed, then hdr_len and
txbuf_len are uninitialized. This commit stops to print uninitialized
value and misleading/false data.
Cc: stable@vger.kernel.org
Fixes: a4422ff22142 (" usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Rex Nie <rex.nie@jaguarmicro.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20241030133632.2116-1-rex.nie@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well, and this resolves a merge
conflict in:
drivers/usb/typec/tcpm/tcpm.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20241101150730.090dc30f@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
self-powered devices
PD3.1 spec ("8.3.3.3.3 PE_SNK_Wait_for_Capabilities State") mandates
that the policy engine perform a hard reset when SinkWaitCapTimer
expires. Instead the code explicitly does a GET_SOURCE_CAP when the
timer expires as part of SNK_WAIT_CAPABILITIES_TIMEOUT. Due to this the
following compliance test failures are reported by the compliance tester
(added excerpts from the PD Test Spec):
* COMMON.PROC.PD.2#1:
The Tester receives a Get_Source_Cap Message from the UUT. This
message is valid except the following conditions: [COMMON.PROC.PD.2#1]
a. The check fails if the UUT sends this message before the Tester
has established an Explicit Contract
...
* TEST.PD.PROT.SNK.4:
...
4. The check fails if the UUT does not send a Hard Reset between
tTypeCSinkWaitCap min and max. [TEST.PD.PROT.SNK.4#1] The delay is
between the VBUS present vSafe5V min and the time of the first bit
of Preamble of the Hard Reset sent by the UUT.
For the purpose of interoperability, restrict the quirk introduced in
https://lore.kernel.org/all/20240523171806.223727-1-sebastian.reichel@collabora.com/
to only non self-powered devices as battery powered devices will not
have the issue mentioned in that commit.
Cc: stable@vger.kernel.org
Fixes: 122968f8dda8 ("usb: typec: tcpm: avoid resets for missing source capability messages")
Reported-by: Badhri Jagan Sridharan <badhri@google.com>
Closes: https://lore.kernel.org/all/CAPTae5LAwsVugb0dxuKLHFqncjeZeJ785nkY4Jfd+M-tCjHSnQ@mail.gmail.com/
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241024022233.3276995-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for DT time properties to allow users to define platform
specific timing deadlines of certain timers rather than using hardcoded
ones. For values that have not been explicitly defined in DT using this
property, default values will be set therefore, making this change
backward compatible.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241022-pd-dt-time-props-v1-2-fea96f51b302@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If drm_dp_hpd_bridge_register() fails, the probe function returns
without removing the fwnode via fwnode_handle_put(), leaking the
resource.
Jump to fwnode_remove if drm_dp_hpd_bridge_register() fails to remove
the fwnode acquired with device_get_named_child_node().
Cc: stable@vger.kernel.org
Fixes: 7d9f1b72b296 ("usb: typec: qcom-pmic-typec: switch to DRM_AUX_HPD_BRIDGE")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-2-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The right function to release a fwnode acquired via
device_get_named_child_node() is fwnode_handle_put(), and not
fwnode_remove_software_node(), as no software node is being handled.
Replace the calls to fwnode_remove_software_node() with
fwnode_handle_put() in qcom_pmic_typec_probe() and
qcom_pmic_typec_remove().
Cc: stable@vger.kernel.org
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-1-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This line is overwriting the result of the above switch-case.
This fixes the tcpm driver getting stuck in a "Sink TX No Go" loop.
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241005144146.2345-1-jonathan@marek.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While design wise the idea of converting the driver to use
the hierarchy of the IRQ chips is correct, the implementation
has (inherited) flaws. This was unveiled when platform_get_irq()
had started WARN() on IRQ 0 that is supposed to be a Linux
IRQ number (also known as vIRQ).
Rework the driver to respect IRQ domain when creating each MFD
device separately, as the domain is not the same for all of them.
Fixes: 9c6235c86332 ("mfd: intel_soc_pmic_bxtwc: Add bxt_wcove_usbc device")
Fixes: d2061f9cc32d ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Fixes: 57129044f504 ("mfd: intel_soc_pmic_bxtwc: Use chained IRQs for second level IRQ chips")
Reported-by: Zhang Ning <zhangn1985@outlook.com>
Closes: https://lore.kernel.org/r/TY2PR01MB3322FEDCDC048B7D3794F922CDBA2@TY2PR01MB3322.jpnprd01.prod.outlook.com
Tested-by: Zhang Ning <zhangn1985@outlook.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241005193029.1929139-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/usb to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use max() for better readability and to fix cocci warnings.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202409231009.2efXAh9b-lkp@intel.com/
Signed-off-by: R Sundar <prosunofficial@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240925122014.552221-1-prosunofficial@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix typos:
reseet->reset,
reaach->reach,
compatiple->compatible.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240919014646.1635774-1-yujiaoliang@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the large set of USB and Thunderbolt changes for 6.12-rc1.
Nothing "major" in here, except for a new 9p network gadget that has
been worked on for a long time (all of the needed acks are here)
Other than that, it's the usual set of:
- Thunderbolt / USB4 driver updates and additions for new hardware
- dwc3 driver updates and new features added
- xhci driver updates
- typec driver updates
- USB gadget updates and api additions to make some gadgets more
configurable by userspace
- dwc2 driver updates
- usb phy driver updates
- usbip feature additions
- other minor USB driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
sub: cdns3: Use predefined PCI vendor ID constant
sub: cdns2: Use predefined PCI vendor ID constant
USB: misc: yurex: fix race between read and write
USB: misc: cypress_cy7c63: check for short transfer
USB: appledisplay: close race between probe and completion handler
USB: class: CDC-ACM: fix race between get_serial and set_serial
usb: r8a66597-hcd: make read-only const arrays static
usb: typec: ucsi: Fix busy loop on ASUS VivoBooks
usb: dwc3: rtk: Clean up error code in __get_dwc3_maximum_speed()
usb: storage: ene_ub6250: Fix right shift warnings
usb: roles: Improve the fix for a false positive recursive locking complaint
locking/mutex: Introduce mutex_init_with_key()
locking/mutex: Define mutex_init() once
net/9p/usbg: fix CONFIG_USB_GADGET dependency
usb: xhci: fix loss of data on Cadence xHC
usb: xHCI: add XHCI_RESET_ON_RESUME quirk for Phytium xHCI host
usb: dwc3: imx8mp: disable SS_CON and U3 wakeup for system sleep
usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode
usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk
usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon
devices
Drivers:
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
Documentation updates
Misc minor cleanups and fixes"
* tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: hwmon: Fix missing temp1_max_alarm attribute
power: supply: Drop use_cnt check from power_supply_property_is_writeable()
power: supply: ab8500: Constify struct kobj_type
power: supply: max1720x: fix a double free on error in probe()
power: supply: axp20x_battery: add support for AXP717
power: supply: axp20x_usb_power: Add support for AXP717
dt-bindings: power: supply: axp20x: Add AXP717 compatible
dt-bindings: power: supply: axp20x: Add AXP717 compatible
power: supply: axp20x_usb_power: Fix spelling mistake "reqested" -> "requested"
power: supply: Change usb_types from an array into a bitmask
power: supply: sysfs: Move power_supply_show_enum_with_available() up
power: supply: sysfs: Add power_supply_show_enum_with_available() helper
power: supply: rt9467-charger: Remove "usb_type" property write support
power: supply: ucs1002: Adjust ucs1002_set_usb_type() to accept string values
power: supply: "usb_type" property may be written to
power: supply: max1720x: add read support for nvmem
mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
power: supply: core: constify psy_tzd_ops
power: reset: brcmstb: Do not go into infinite loop if reset fails
power: reset: brcmstb: Use devm_register_sys_off_handler()
...
|
|
TCPCI USB PHY - PTN5110 could be used with SOCs that only support
the edge-triggered GPIO interrupts such as TI's K3 device AM69.
Move the interrupt configuration to the firmware which would
allow to accommodate edge triggered interrupts for such SOCs.
In order to support the edge interrupts, register irq line in advance
and keep track of occurrence during port registering.
When the edge interrupts are used, it is observed that some of the
interrupts are missed when tcpci_irq() is serving the current
interrupt. Therefore, check the status register at the end of
tcpci_irq() and re-run the function if the status is not clear
i.e. pending interrupt.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240905065328.7116-1-parth105105@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.
This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.
This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We need the usb / thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpci_maxim currently never triggers the TCPM state machine when CC
status has not changed due to a contaminant but due to a real
connection event, i.e. a genuine plug event, meaning the system will
stay idle and not notify any subscribers.
The reason is that the initial state of the port is 'toggling', which
causes _max_tcpci_irq() to only drive the contamination part of the
TCPM state machine (via tcpm_port_clean()).
What should happen instead is that if no contamination was detected,
the TCPM should be notified of the CC change in this case.
To fix this, we update ...is_contaminant() to also allow its caller to
determine if more CC processing is required and then call into the TCPM
as required.
While at it, add a kernel-doc for max_contaminant_is_contaminant().
Note: the code has an issue where I2C errors during contaminant
detection also cause the TCPM state machine to not be updated. This
commit doesn't change this behaviour and should be addressed by
follow-up commit(s).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240806-max33359-toggling-v2-1-a66ab37baafb@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit bf20c69cf3cf9c6445c4925dd9a8a6ca1b78bfdf.
During tcpm_init() stage, if the VBUS is still present after
tcpm_reset_port(), then we assume that VBUS will off and goto safe0v
after a specific discharge time. Following a TCPM_VBUS_EVENT event if
VBUS reach to off state. TCPM_VBUS_EVENT event may be set during
PORT_RESET handling stage. If pd_events reset to 0 after TCPM_VBUS_EVENT
set, we will lost this VBUS event. Then the port state machine may stuck
at one state.
Before:
[ 2.570172] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.570179] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.570182] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 3.490213] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [delayed 920 ms]
[ 3.490220] Start toggling
[ 3.546050] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 3.546057] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
After revert this patch, we can see VBUS off event and the port will goto
expected state.
[ 2.441992] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.441999] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.442002] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 2.442122] VBUS off
[ 2.442125] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev1 NONE_AMS]
[ 2.442127] VBUS VSAFE0V
[ 2.442351] CC1: 0 -> 0, CC2: 0 -> 0 [state SNK_UNATTACHED, polarity 0, disconnected]
[ 2.442357] Start toggling
[ 2.491850] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 2.491858] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
[ 2.491863] pending state change SRC_ATTACH_WAIT -> SNK_TRY @ 200 ms [rev1 NONE_AMS]
[ 2.691905] state change SRC_ATTACH_WAIT -> SNK_TRY [delayed 200 ms]
Fixes: bf20c69cf3cf ("usb: typec: tcpm: clear pd_event queue in PORT_RESET")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240809112901.535072-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the usb fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of open-coding the call to tcpci_unregister_port() in various
places, let's just register a hook using devm_add_action_or_reset() so
that it gets called automatically as and when necessary by the device
management APIs.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-15-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dev_err_probe() exists as a useful helper ensuring standardized
error messages during .probe() and using it also helps to make
the code more legible.
Use it.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-14-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert register TCPC_VENDOR_ADC_CTRL1 to using GENMASK() and
FIELD_PREP() so as to keep using a similar approach throughout the code
base and make it arguably easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-13-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert register TCPC_VENDOR_CC_CTRL3 to using GENMASK() so as to keep
using a similar approach throughout the code base and make it arguably
easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-12-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert register TCPC_VENDOR_CC_CTRL2 to using GENMASK() and
FIELD_PREP() so as to keep using a similar approach throughout the code
base and make it arguably easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-11-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Only one user of STATUS_CHECK() remains, and the code can actually be
made more legible by simply avoiding the use of that wrapper macro,
allowing to also drop the macro altogether.
Do so.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-10-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need for using the ternary if/else here, simply mask
TCPC_ALERT_RX_BUF_OVF as necessary, which arguably makes the code
easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-9-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This makes it easier to see what's missing and what's being programmed.
While at it, add brackets to help with formatting and remove a comment
that doesn't add much value.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-8-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert all fields from register TCPC_TRANSMIT to using GENMASK() and
FIELD_PREP() so as to keep using a similar approach throughout the code
base and make it arguably easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-7-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert field TCPC_MSG_HDR_INFO_REV from register TCPC_MSG_HDR_INFO to
using GENMASK() and FIELD_PREP() so as to keep using a similar approach
for all fields.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-6-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Align the last remaining field TCPC_ROLE_CTRL_RP_VAL with the other
fields in the TCPC_ROLE_CTRL register by using GENMASK() and
FIELD_PREP().
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-5-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All this open-coded shifting and masking is quite hard to read, in
particular the if-statement in tcpci_apply_rc().
Declare TCPC_ROLE_CTRL_CC[12] using GENMASK() which allows using
FIELD_GET() and FIELD_PREP() to arguably make the code more legible.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-4-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The existing code here, particularly in maxim_contaminant.c, is
arguably quite hard to read due to the open-coded masking and shifting
spanning multiple lines.
Use GENMASK() and FIELD_GET() instead, which arguably make the code
much easier to follow.
While at it, use the symbolic name TCPC_CC_STATE_SRC_OPEN for one
instance of open-coded 0x0.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-3-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We loop while the status is != 0, so rephrase the comment slightly for
clarity.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-2-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
source capability message
Since commit (122968f8dda8 usb: typec: tcpm: avoid resets for missing
source capability messages), state will change from SNK_WAIT_CAPABILITIES
to SNK_WAIT_CAPABILITIES_TIMEOUT. We need to change SNK_WAIT_CAPABILITIES
-> SNK_READY path to SNK_WAIT_CAPABILITIES_TIMEOUT -> SNK_READY
accordingly. Otherwise, the sink port will never change to SNK_READY state
if the source does't have PD capability.
[ 503.547183] pending state change SNK_WAIT_CAPABILITIES -> SNK_WAIT_CAPABILITIES_TIMEOUT @ 310 ms [rev3 NONE_AMS]
[ 503.857239] state change SNK_WAIT_CAPABILITIES -> SNK_WAIT_CAPABILITIES_TIMEOUT [delayed 310 ms]
[ 503.857254] PD TX, header: 0x87
[ 503.862440] PD TX complete, status: 2
[ 503.862484] state change SNK_WAIT_CAPABILITIES_TIMEOUT -> SNK_UNATTACHED [rev3 NONE_AMS]
Fixes: 122968f8dda8 ("usb: typec: tcpm: avoid resets for missing source capability messages")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20240802064156.1846768-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tcpci_check_std_output_cap() function is supposed to return negative
error codes but it's declared as type bool so the error handling doesn't
work. Declare it as an int instead.
Fixes: 62ce9ef14797 ("usb: typec: tcpci: add support to set connector orientation")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/b0880888-6719-4614-91fc-8ee63b71d304@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
i2c_device_id::driver_data to 0
These driver don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240710073050.192806-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This add the support to set the optional connector orientation bit which
is part of the optional CONFIG_STANDARD_OUTPUT register 0x18 [1]. This
allows system designers to connect the tcpc orientation pin directly to
the 2:1 ss-mux.
[1] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240701132133.3054394-1-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240604212730.4968-2-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB / Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A USB-C hard reset involves removing the voltage from VBUS for some
time. So basically it has the same effect as removing the USB-C plug
for a short moment. If the machine is powered from the USB-C port and
does not have a fallback supply (e.g. a battery), this will result in
a full machine reset due to power loss.
Ideally we want to avoid triggering a hard reset on these boards. A
non-working USB-C port is probably better than unplanned reboots. But
boards with a backup supply should do the hard reset to get everything
working again.
In theory it would be enough to check the self_powered property, but
it seems the property might not be configured consistently enough in
system firmwares.
So let's start with just printing an error message when a hard reset is
triggered on systems we expect to be affected. This at least makes
debugging issues on affected systems easier without impacting unaffected
systems too much.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240523171645.223225-1-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the Linux Type-C controller drivers probe, they requests a soft
reset, which should result in the source restarting to send Source
Capability messages again independently of the previous state.
Unfortunately some USB PD sources do not follow the specification and
do not send them after a soft reset when they already negotiated a
specific contract before. The current way (and what is described in the
specificiation) to resolve this problem is triggering a hard reset.
But a hard reset is fatal on batteryless platforms powered via USB-C PD,
since that removes VBUS for some time. Since this is triggered at boot
time, the system will be stuck in a boot loop. Examples for platforms
affected by this are the Radxa Rock 5B or the Libre Computer Renegade
Elite ROC-RK3399-PC.
Instead of directly trying a hard reset when no Source Capability
message is send by the USB-PD source automatically, this changes the
state machine to try explicitly asking for the capabilities by sending
a Get Source Capability control message.
For me this solves issues with 2 different USB-PD sources - a RAVPower
powerbank and a Lemorele USB-C dock. Every other PD source I own
follows the specification and automatically sends the Source Capability
message after a soft reset, which works with or without this change.
I decided against making this extra step limited to devices not having
the self_powered flag set, since I don't see any huge drawbacks in this
approach and it keeps the logic simpler. The worst case scenario would
be a power source, which is really stuck. In that case the hard reset
is delayed by another 310ms.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240523171806.223727-1-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Similar to what fixed in Commit a6fe37f428c1 ("usb: typec: tcpm: Skip
hard reset when in error recovery"), the handling of the received Hard
Reset has to be skipped during TOGGLING state.
[ 4086.021288] VBUS off
[ 4086.021295] pending state change SNK_READY -> SNK_UNATTACHED @ 650 ms [rev2 NONE_AMS]
[ 4086.022113] VBUS VSAFE0V
[ 4086.022117] state change SNK_READY -> SNK_UNATTACHED [rev2 NONE_AMS]
[ 4086.022447] VBUS off
[ 4086.022450] state change SNK_UNATTACHED -> SNK_UNATTACHED [rev2 NONE_AMS]
[ 4086.023060] VBUS VSAFE0V
[ 4086.023064] state change SNK_UNATTACHED -> SNK_UNATTACHED [rev2 NONE_AMS]
[ 4086.023070] disable BIST MODE TESTDATA
[ 4086.023766] disable vbus discharge ret:0
[ 4086.023911] Setting usb_comm capable false
[ 4086.028874] Setting voltage/current limit 0 mV 0 mA
[ 4086.028888] polarity 0
[ 4086.030305] Requesting mux state 0, usb-role 0, orientation 0
[ 4086.033539] Start toggling
[ 4086.038496] state change SNK_UNATTACHED -> TOGGLING [rev2 NONE_AMS]
// This Hard Reset is unexpected
[ 4086.038499] Received hard reset
[ 4086.038501] state change TOGGLING -> HARD_RESET_START [rev2 HARD_RESET]
Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240520154858.1072347-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There could be a potential use-after-free case in
tcpm_register_source_caps(). This could happen when:
* new (say invalid) source caps are advertised
* the existing source caps are unregistered
* tcpm_register_source_caps() returns with an error as
usb_power_delivery_register_capabilities() fails
This causes port->partner_source_caps to hold on to the now freed source
caps.
Reset port->partner_source_caps value to NULL after unregistering
existing source caps.
Fixes: 230ecdf71a64 ("usb: typec: tcpm: unregister existing source caps before re-registration")
Cc: stable@vger.kernel.org
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240514220134.2143181-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a probe function returns -EPROBE_DEFER after creating another device
there is a change of ending up in a probe deferral loop, (see commit
fbc35b45f9f6 ("Add documentation on meaning of -EPROBE_DEFER"). In case
of the qcom-pmic-typec driver the tcpm_register_port() function looks up
external resources (USB role switch and inherently via called
typec_register_port() USB-C muxes, switches and retimers).
In order to prevent such probe-defer loops caused by qcom-pmic-typec
driver, use the API added by Johan Hovold and move HPD bridge
registration to the end of the probe function.
The devm_drm_dp_hpd_bridge_add() is called at the end of the probe
function after all TCPM start functions. This is done as a way to
overcome a different problem, the DRM subsystem can not properly cope
with the DRM bridges being destroyed once the bridge is attached. Having
this function call at the end of the probe function prevents possible
DRM bridge device creation followed by destruction in case one of the
TCPM start functions returns an error.
Reported-by: Caleb Connolly <caleb.connolly@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240424-qc-pmic-typec-hpd-split-v4-1-f7e10d147443@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
typec_register_partner() does not guarantee partner registration
to always succeed. In the event of failure, port->partner is set
to the error value or NULL. Given that port->partner validity is
not checked, this results in the following crash:
Unable to handle kernel NULL pointer dereference at virtual address xx
pc : run_state_machine+0x1bc8/0x1c08
lr : run_state_machine+0x1b90/0x1c08
..
Call trace:
run_state_machine+0x1bc8/0x1c08
tcpm_state_machine_work+0x94/0xe4
kthread_worker_fn+0x118/0x328
kthread+0x1d0/0x23c
ret_from_fork+0x10/0x20
To prevent the crash, check for port->partner validity before
derefencing it in all the call sites.
Cc: stable@vger.kernel.org
Fixes: c97cd0b4b54e ("usb: typec: tcpm: set initial svdm version based on pd revision")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240427202812.3435268-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Before sending Enter Mode for an Alt Mode, there is a gap between Discover
Modes and the Alt Mode driver queueing the Enter Mode VDM for the port
partner to send a message to the port.
If this message results in unregistering Alt Modes such as in a DR_SWAP,
then the following deadlock can occur with respect to the DisplayPort Alt
Mode driver:
1. The DR_SWAP state holds port->lock. Unregistering the Alt Mode driver
results in a cancel_work_sync() that waits for the current dp_altmode_work
to finish.
2. dp_altmode_work makes a call to tcpm_altmode_enter. The deadlock occurs
because tcpm_queue_vdm_unlock attempts to hold port->lock.
Before attempting to grab the lock, ensure that the port is in a state
vdm_run_state_machine can run in. Alt Mode unregistration will not occur
in these states.
Fixes: 03eafcfb60c0 ("usb: typec: tcpm: Add tcpm_queue_vdm_unlocked() helper")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202356.3372314-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
